| Internet-Draft | BGP CPR for SRv6 Service | March 2023 |
| Wang, et al. | Expires 27 September 2023 | [Page] |
This document describes a mechanism to advertise different IPv6 prefixes which are associated with different color attributes to establish end-to-end intent-aware paths for SRv6 services. Such IPv6 prefixes are called "Colorful Prefixes", and this mechanism is called Colorful Prefix Routing (CPR). In SRv6 networks, the colorful prefixes are the SRv6 locators associated with different intent. SRv6 services (e.g. SRv6 VPN services) with specific intent could be assigned with SRv6 SIDs under the corresponding SRv6 locators, which are advertised as colorful prefixes. This allows the SRv6 service traffic to be steered into end-to-end intent-aware paths simply based on the SRv6 Service SIDs. The existing IPv6 Address Family could be used for the advertisement of IPv6 colorful prefixes, thus this mechanism is easy to interoperate and allows incremental deployment in multi-domain networks.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 27 September 2023.¶
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
With the trend of using one common network to carry multiple types of services, each service type can have different requirements on the network. Such requirements are usually considered as the "intent" of the service or customer, and is represented as an abstract notion called "color".¶
In network scenarios where the services are delivered across multiple network domains, there is need to provide the services with different end-to-end paths to meet the intent. [I-D.hr-spring-intentaware-routing-using-color] describes the problem statements and requirements for inter-domain intent-aware routing.¶
The inter-domain path can be established using either MPLS or IP data plane. In MPLS based networks, the traditional inter-domain approach is to establish an end-to-end LSP based on the BGP-LU mechanisms as defined in [RFC8277]. Each domain or area border node needs to perform label swapping for the end-to-end BGP-LU LSP, and encapsulate the label stack which are used for the intra-domain LSP within the subsequent network domain or area.¶
While in IP based networks, the IP reachability information can be advertised to network nodes in different domains using BGP, so that all the domain or area border nodes have the routes to the IP prefixes of the destination node in other domains. With the introduction of SRv6 [RFC8986], services are assigned with SRv6 Service SIDs [RFC9252], which are routable in the network according to its SRv6 locator prefix. Thus the inter-domain path can be established simply based on the inter-domain prefix routes, and the BGP-LU inter-domain LSP mechanism is not necessary for IPv6 and SRv6 based networks.¶
This document describes a mechanism to advertise different IPv6 prefixes which are associated with different color attributes to establish end-to-end intent-aware paths for SRv6 services. Such IPv6 prefixes are called "Colorful Prefixes", and this mechanism is called Colorful Prefix Routing (CPR). In SRv6 networks, the colorful prefixes are the SRv6 locators associated with different intent. SRv6 services (e.g. SRv6 VPN services) with specific intent could be assigned with SRv6 SIDs under the corresponding SRv6 locators, which are advertised as colorful prefixes. This allows the SRv6 service traffic to be steered into end-to-end intent-aware paths simply based on the SRv6 Service SIDs. The existing IPv6 Address Family could be used for the advertisement of IPv6 colorful prefixes, thus this mechanism is easy to interoperate and allows incremental deployment in multi-domain networks.¶
This section describes the BGP CPR mechanisms. More specifically, section 2.1 describes the allocation of the IPv6 colorful prefixes, section 2.2 describes the advertisement of colorful prefixes in BGP, section 2.3 describes the resolution of CPR routes to the intra-domain paths, and section 2.4 describes the steering of SRv6 services to CPR routes.¶
In SRv6 networks, an SRv6 locator needs to be allocated for each node. In order to distinguish N different intent, a PE node needs to be allocated with N SRv6 locators, each of which is associated a different intent. This can be achieved by splitting the base SRv6 locator of the node into N sub-locators, and these sub-locators are called colorful locators.¶
For example, node PE2 is allocated with the base SRv6 Locator 2001:db8:aaaa:1::/64. In order to provide 16 different intent, this base SRv6 Locator is split into 16 sub-locators from 2001:db8:aaaa:1:0000::/68 to 2001:db8:aaaa:1:F000::/68, each of these sub-locators is associated with a different intent, such as low-delay, high-bandwidth, etc.¶
After the allocation of colorful prefixes on a PE node, routes to these colorful prefixes need to be advertised both in the local domain and also to other domains using BGP, so that the SRv6 services routes could be resolved using the corresponding CPR route.¶
In a multi-domain IPv6 network, the IPv6 unicast Address Family/Subsequent Address Family (AFI/SAFI = 2/1) [RFC2545] is used for the advertisement of the colorful prefix routes. The color extended community [RFC9012] is carried with the colorful prefix route. The procedure of colorful prefix advertisement is described using an example with the following topology:¶
Color Domain: Color Domain: Color Domain:
C11, C12,... C21, C22,... C31, C32,...
+--------------+ +--------------+ +-------------+
| | | | | |
| [ASBR11]---[ASBR21] [ASBR23]---[ASBR31] |
--[PE1] [P1] | X | [P2] | X | [P3] [PE3]--
| [ASBR12]---[ASBR22] [ASBR24]---[ASBR32] |
| | | | | |
+--------------+ +--------------+ +-------------+
AS1 AS2 AS3
Colorful Prefixes of PE3:
Low delay: 2001:db8:aaaa:1:1000::/68
high bandwidth: 2001:db8:aaaa:1:2000::/68
...
Figure 1. Example Topology for CPR Route Illustration
¶
Assume PE3 is provisioned with two different colorful prefixes CLP-1 and CLP-2 for two different intent such as "low-delay" and "high-bandwidth" respectively. Note that in different network domains, the color representing the same intent may be different. In this example, the color used for "low-delay" in AS1, AS2 and AS3 are C11, C21 and C31 respectively, and the color used for "high-bandwidth" in AS1, AS2 and AS3 are C12, C22 and C32 respectively.¶
In network scenarios where some of the intermediate network domains are MPLS based, the CPR routes may still be advertised using the IPv6 unicast address family (AFI/SAFI=2/1) in the MPLS-based intermediate domains, and at the MPLS domain border nodes, some route resolution policy could be used to make the CPR routes resolved to intra-domain intent-aware MPLS LSPs. Another possible mechanism is to use the IPv6 Labeled Unicast address family (AFI/SAFI=2/4) to advertise the CPR routes in the MPLS domains, the detailed procedure is described in Section 7.1.2.1 of [I-D.agrawal-spring-srv6-mpls-interworking].¶
A domain border node which receives a CPR route can resolve the CPR route to an intra-domain color-aware path based on the tupple (N, C), where N is the next-hop of the CPR route, and C is the color extended community of the CPR route. The intra-domain color-aware path could be built with any of the following mechanisms:¶
For example, PE1 receives a CPR route to PE3:CL1 with color C31 and next-hop ASBR11, it can resolve the CPR routes to an intra-domain SRv6 Policy based on the tupple (ASBR11, C31).¶
The intra-domain path resolution scheme could be based on any existing tunnel resolution policy, and new tunnel resolution mechanisms could be introduced if needed.¶
For an SRv6 service which is associated with a specific intent, the SRv6 Service SID could be allocated under the corresponding colorful locator prefix. For example, on PE3 in the example topology, an SRv6 VPN service with the low delay intent can be allocated with the SRv6 End.DT4 SID 2001:db8:aaaa:1:1000::0100, where 2001:db8:aaaa:1:1000::/68 is the SRv6 colorful prefix for low delay service.¶
The SRv6 service routes are advertised using the mechanism defined in [RFC9252], the SRv6 Service SID is carried using the BGP Prefix-SID attribute [RFC8669]. The inter-domain VPN Option C is used, which means the next-hop of the SRv6 service route is set to the originating PE and not changed. Since the intent of the service is embedded in the SRv6 service SID, the SRv6 service route does not need to carry the color extended community.¶
With the CPR routing mechanism, the ingress PE node which receives the SRv6 service routes follows the behavior of SRv6 best-effort forwarding. The SRv6 service SID carried in the service route is used as the destination address in the outer IPv6 header encapsulated to the service packet. If the corresponding CPR route has been received and installed, the SRv6 service SID can match with the colorful prefix of the CPR route, then the intra-domain color-aware path which the CPR route is resolved to is used for forwarding the SRv6 service traffic.¶
This section describes the encapsulation and forwarding process of data packets which are matched with the corresponding CPR route.¶
Following is an illustration of the packet encapsulation and forwarding process of CPR over SRv6 Policy. The abstract representation of IPv6 and SRH in section 6 of [RFC8754] is used.¶
PE3 is provisioned with a colorful prefix PE3:C1 for "low-delay".¶
In AS1, the SRv6 Policy for (ASBR11, C11) is represented with SID list (P1, BR11).¶
In AS2, the SRv6 Policy for (ASBR23, C21) is represented with the SID list (P2, BR23).¶
In AS3, the SRv6 Policy for (PE3, C31) is represented with the SID list (P3, PE3).¶
For packets which belong to an SRv6 VPN service associated with the SRv6 Service SID PE3:CL1.DT, the packet encapsulation and forwarding process is shown as below:¶
PE1 ->P1 : (PE1, P1)(PE3:CL1.DT, BR11; SL=2)(C-pkt) P1 ->BR11: (PE1, BR11)(PE3:CL1.DT, BR11; SL=1)(C-pkt) BR11->BR21: (PE1, PE3:CL1.DT)(C-pkt) BR21->P2 : (PE1, P2)(PE3:CL1.DT, BR23; SL=2)(C-pkt) P2 ->BR23: (PE1, BR23)(PE3:CL1.DT, BR23; SL=1)(C-pkt) BR23->BR31: (PE1, PE3:CL1.DT)(C-pkt) BR31->P3 : (PE1, P3)(PE3:CL1.DT, PE3; SL=2)(C-pkt) P3 ->PE3 : (PE1, PE3)(PE3:CL1.DT, PE3; SL=1)(C-pkt)¶
In some network domains, SRv6 Flex-Algo may be used to provide intent aware intra-domain path. The encapsulation is similar to the case with SRv6 Policy.¶
In network scenarios where some of the network domains use MPLS based data plane, the CPR route can be resolved over a color-aware intra-domain MPLS LSP. Such intra-domain MPLS LSP may be established using SR-MPLS Policy, SR-MPLS Flex-Algo or RSVP-TE.¶
The encapsulation and forwarding of SRv6 service packets over an intra-domain MPLS LSP is based on the MPLS mechanisms as defined in [RFC3031] [RFC3032] and [RFC8660].¶
In AS1, the SR-MPLS Policy for (ASBR11, C11) is represented with Label-stack (P1, BR11).¶
In AS2, the SR-MPLS Flex-Algo for (ASBR23, C21) is represented with Label-stack (BR23).¶
In AS3, the SR-MPLS Policy for (PE3, C31) is represented with Label-stack (P3, PE3).¶
For packets which belong to an SRv6 VPN service associated with the SRv6 Service SID PE3:CL1.DT, the packet encapsulation and forwarding process is shown as below:¶
PE1 ->P1 : Label-stack (P1, BR11) (PE1, PE3:CL1.DT)(C-pkt) P1 ->BR11: Label-stack (BR11) (PE1, PE3:CL1.DT)(C-pkt) BR11->BR21: (PE1, PE3:CL1.DT)(C-pkt) BR21->P2 : Label-stack (BR23) (PE1, PE3:CL1.DT)(C-pkt) P2 ->BR23: Label-stack (BR23) (PE1, PE3:CL1.DT)(C-pkt) BR23->BR31: (PE1, PE3:CL1.DT)(C-pkt) BR31->P3 : Label-stack (P3, PE3) (PE1, PE3:CL1.DT)(C-pkt) P3 ->PE3 : Label-stack (PE3) (PE1, PE3:CL1.DT)(C-pkt)¶
When the colorful prefixes are assigned as the sub-locators of the node's base SRv6 locator, the IPv6 unicast route of the base locator prefix is the covering prefix of all the colorful locator prefixes. To make sure the colorful locator prefixes can be distributed to the ingress PE nodes along the border nodes, it is required that route aggregation be disabled for IPv6 unicast routes which carries the color extended community.¶
All the border nodes and the ingress PE nodes needs to install the colorful locator prefixes into the RIB and FIB. For transit domains which support the CPR mechanism, the border nodes can use the tupple (N, C) to resolve the CPR routes to intent-aware intra-domain paths. For transit domains which do not support the CPR mechanism, the border nodes could resolve the CPR routes over a best effort intra-domain path to the next-hop N, while the CPR route will be advertised further to the downstream domains with only the next-hop changed to itself. This allows the CPR routes to be resolved to intent-aware intra-domain paths in any network domains which support the CPR mechanism, while can fall back to resolve over best-effort intra-domain paths in the legacy network domains.¶
This document makes no request of IANA.¶
The mechanism described in this document provide an approach for inter-domain intent-aware routing based on existing BGP protocol mechanisms. It does not introduces any additional security considerations than those described in [RFC4271] and [RFC4272].¶
The authors would like to thank Shunwan Zhuang and Zhibo Hu for the review and discussion.¶