Architecture and Framework for IPv6 over Non-Broadcast Access

2.1. ND-Classic and ND-Proxies

Though ND-Classic was the state of the art when designed for early Ethernet links at the end of the twentieth century, it is less appropriate for modern networks such as wireless and overlays that cannot provide the same cheap and reliable broadcast as a shared yellow wire. The reactive AR operation was designed to limit the amount of memory that is needed for the ND cache, at times where memory was scarce in the adapters. This trade-off, broadcast bandwidth vs. memory in the adapters, should be reevaluated for networks where router memory is aplenty but broadcast has become expensive.¶

The ND-Classic Neighbor Solicitation (NS) [RFC4861] message is used as a multicast IP packet for AR and DAD [RFC4862]. While the AR message is intended for one node that owns the Target address, the expectation for DAD is that there's no node at all with that address. A message that is intended for at most one node is certainly a poor match for a broadcast operation.¶

The NS message for AR and DAD are sent at the network layer to a Solicited-Node multicast address (SNMA) [RFC4291] and should in theory only reach a very small group of nodes. But to support SNMA, the host must also support multicast Listener Discovery (MLD) [RFC3810], which may be an additional burden to a constrained stack, and the switches should support their own multicast routing and state, which is pushing the real problems to the lower layers.¶

Also, if implemented, the SNMA proceure would entail close to one state per address is every switch since there is often only one address with the same SNMA in the network - though the birthday paradox applies. This amount of memory may not have been available in early switches, and still makes little economical sense today when a complete ND cache requires one state per address in every router only, as opposed to one in every switch, when the Subnet prefix is advertised as not-onlink.¶

This is why, in practice, ND-Classic messages to a SNMA are mapped to link-layer broadcast on Ethernet and Wireless networks, and to full ingress replication in overlays. multicast NS transmissions may occur when a node joins the network, moves, or wakes up and reconnects to the network. Over a very large fabric, this can generate hundreds of broadcasts per second.¶

If the broadcasts were blindly copied over Wi-Fi links, the link-layer broadcast traffic associated to ND network-layer multicast could consume enough bandwidth to cause a substantial degradation to the unicast service [MCAST EFFICIENCY]. This is why ND Proxies are deployed and charged to reduce the resulting flood; sadly, ND-Proxies are not fully reliable for the lack of a deterministic state on all existing addresses, which leads to unpredictable failures in ND-Classic operations.¶

The ND-Classic Neighbor Advertisement (NA) [RFC4861] message can also be sent as a multicast to all nodes, as a gratuitous information that can be used to override the address mapping in nodes with an existing Neighbor Cache Entry (NCE) for the Target address. If this is done, all nodes in the broadcast domain are impected though there's probably none or very few with an NCE. When it is not done, nodes with an NCE will be unable to reach the Target IP address until Neighbor Unreachability Detection (NUD) discovers the issue. Both alternatives are unsatisfactory, meaning that the whole approach should be revisited.¶

This problem can be alleviated by reducing the size of the broadcast domain that encompasses wireless access links. This has been done in the art of IP subnetting by partitioning the subnets and by routing between them, at the extreme by assigning a prefix, say a /64, to each wireless node (see [RFC8273]).¶

Another way to split the broadcast domain within a Subnet is to proxy the network-layer protocols that rely on link-layer broadcast operations at the boundary of the split broadcast domains. As an example, [IEEE Std. 802.11] recommends deploying an "ARP proxy" for the IPv4 address Resolution Protocol (ARP) and ND-Classic at the APs. The correct operation of the proxy requires the exhaustive list of the IP addresses for which proxying is provided. Forming and maintaining that knowledge is a hard problem in the general case of radio connectivity, which keeps changing with movements and variations in the environment that alter the range of transmissions. It is achieved in Wi-Fi networks through the proactive method of the wireless association, which is akin to the registration procedure in this architecture.¶

[SAVI] suggests discovering the addresses by snooping the ND-Classic protocol, but that can also be unreliable. An IPv6 address may not be discovered immediately due to a packet loss. It may never be discovered in the case of a "silent" node that is not currently using one of its addresses, e.g., a printer that waits in wake-on-lan state. A change of anchor, e.g. due to a movement, may be missed or misordered, leading to unreliable connectivity and an incomplete list of addresses. Bottom line: snooping ND-Classic is not appropriate to form and maintain a deterministic knowledge of the IPv6 addresses of all the neighbors that are reachable over a network port.¶

2.2. The case of Wireless

Like Transparent Bridging, the ND-Classic operation is reactive, and relies on IP multicast for the AR and DAD procedures. As discussed in Section 2, the network-layer multicast operation is typically implemented as a link-layer broadcast for the lack of an adapted and scalable link-layer multicast operation on most WLANs and Low-Power Personal Area Networks (LoWPANs). It results that on wireless, ND-Classic multicast messages are typically broadcasted.¶

As opposed to unicast transmissions, the broadcast transmissions over wireless links are not subject to automatic retries (ARQ) and therefore are not reliable. Reducing the speed at the physical (PHY) layer for broadcast transmissions can increase the reliability, at the expense of a higher relative cost of broadcast on the overall available bandwidth.¶

Excessive use of broadcast by protocols such as ND-Classic and Bonjour led network administrators to install multicast rate limiting to protect the network. Experimentally, this proved to have a dramatic effect on ND performance in large wireless networks. From some testing done at an IETF meeting a few years ago, it seemed that up to 90% of IPv6 link-local multicasts were dropped. The impact on user experience is usually limited since for the most part, the users will connect to addresses outside the Subnet and will not attempt to locate one another. The impact on the NOC might still be significant, since a failure related to ND operations might be transient and difficult to debunk after the fact.¶

Another experiment conducted during an IETF meeting consisted in manually forcing address duplicates to observe the DAD behavior. This experiment showed that DAD often (up to 80% of times was observed) fails to discover the duplication of IPv6 addresses, at least in a large wireless access networks, see [DAD ISSUES] for more. In practice, IPv6 addresses very rarely conflict, not because the address duplications are detected and resolved by the DAD operation, but thanks to the entropy of the typically 64-bit Interface IDs (IIDs) that makes a collision quasi-impossible for randomized IIDs. This is why, even when DAD fails, the user experience is rarely affected.¶

Excessive use of broadcast also places a toll on the battery of wireless devices such as IoT sensors and smartphones. On paper, a Wi-Fi station must keep its radio turned on to listen to the periodic series of broadcast frames. Most of those broadcasts are dropped at the network layer when the receiving node finds it is not interested, as is the case of NS messages when the node is not the Target. In order to protect the battery lifetime, a typical smartphone will listen at a multiple of the broadcast period, blindly ignoring a large ratio of the broadcasts, and making ND-Classic operations even less reliable.¶

Net-net: broadcast transmissions are not reliable on wireless. Protocols designed for bridged networks that rely on broadcast transmissions often exhibit disappointing behaviors when employed unmodified on a local wireless medium (more in [MCAST PROBLEMS]). Even though there is at most one intended Target for a broadcast AR or DAD message, the broadcast impacts many wireless nodes over the whole Subnet (e.g., the ESS fabric), and yet the chances that intended Target receives the packet are limited. The fact that the user experience for classic-ND is not so dramatically affected only shows that those broadcasts are, for a large part, a useless waste of expensive resources.¶

Wi-Fi Access Points [IEEE Std. 802.11] (APs) deployed in an Extended Service Set (ESS) act as [IEEE Std. 802.1] bridges between the wireless stations (STA) and the wired backbone. As opposed to the classical Transparent (aka Learning) Bridge operation that installs the forwarding state reactively to traffic, the bridging state in the AP is established proactively, at the time of association. The association process registers the link-layer (MAC) address of the STA to the AP proactively, i.e., before it is needed. Based on that information, the AP maintains the exhaustive list of the associated MAC addresses and blocks the link-layer lookups for destination MAC addresses that are not associated to this AP. The association procedure protects the wireless medium against broadcast-intensive Transparent Bridging lookups, but the network-layer problem remains for the lack of a similar procedure at the network layer.¶

2.3. The case of Overlays

link-layer Overlays (VLANs) reduce the broadcast domain from the physical one, whereas network-layer overlays (e.g., VxLAN) can extend the Subnet beyond the limits of the physical network, enabling to deploy a Subnet over large physical domains. network-layer overlays are a clear indication of the need to decouple the Subnet from the limits of the physical network.¶

A network-layer overlay is typically a partial or full mesh of point to point tunnels between routers. In case of a full mesh, BUM (Broadcast, Unknown, and multicast) forwarding across the overlay can be implemented as a replication at the ingress router or at a dedicated reflector, but either way entails a growing congestion and latency as the overlay grows in size. BUM forwarding has become so detrimental to the network operations that some operators decide to turn it off. This means that a silent node, whose location is unknown to the fabric control plane and possibly forgotten, cannot be rediscovered by AR procedures, and will not be reachable again until it volunteers its own sign of life. To avoid this, modern protocols should be designed such that the use of overlay-wide broadcasts are limited to operations where a real distribution operation is desired, e.g., every node is interested in receiving the packet.¶

While a multicast ND-Classic RA message may be of interest within a site or a subsite to all local nodes, it is probably of little interest to other sites that are served by other routers, even when the overlay spans across both sites. The same goes for a local printer, the broadcast mDNS lookup should reach local printers but not faraway ones. This is another indication of the need to decouple the span of the Subnet from the lower layer broadcast domain, and dedicate the broadcast service to local operations such as discovery.¶

As discussed in Section 2.2, multicast ND-Classic messages are in fact broadcasted across the overlay, meaning that they contribute to the BUM traffic and are treated as full broadcast. Yet, those messages are used for AR and DAD and intend to reach at most one node, the owner of the Target address, if any. Using a BUM transmission that reaches every nodes in the overlay to communicate with at most one is a misuse of the overlay resources and should be replaced by unicast-based methods.¶

In data centers, overlays are typically combined with server multihoming at the edge. An advanced Network Interface Card (NIC) is equipped with more than one Ethernet ports for redundancy, which connect to different leaf switches (aka ToR) to the same cloud network. The server (say, using Kubernetes) needs a single address and would rather use that address on both ports to the same Subnet, and use either network port for its own reasons, e.g., load balancing, independently of IP addressing considerations. This means that the IP Interface abstraction that the server needs is a logical construct, decoupled from the network ports, and capable to encompass more than one.¶

2.4. Power and Sustainability

In the wireless case, broadcasts are sent at the slowest speed available, which can be a hundred time slower than unicast transmissions, in order to maximize the chances that all nodes in the BSS will receive the frame. For that extra long duration, the broadcast transmission holds the spectrum locally, which adds to the unicast latency, and generates interferences remotely, which may cascade in losses and retries in adjacent networks. In the process, the broadcast transmission consumes up to a hundred time more power than unicast transmission of equivalent payload size. Power is also wasted when replicating a multicast packet to span an overlay, each time the packet is ultimately dropped by the recipient.¶

Constrained IoT devices conserve their power by placing themselves in deep sleep for most of the time. While a device is sleeping, it cannot answer ND-Classic messages for AR and DAD. This makes ND-Classic unsuitable to IoT devices. The 6LoWPAN WG has determined that the most appropriate model for a constrained network is a pull model where the device wakes up, negotiates with its router(s) for addresses and connectivity for some amount of time in the future, and goes back to sleep. The router can then perform a role of sleep proxy that defends the address(es) and holds traffic for the device till the device wakes up and pulls it from the router. Additionally, when the constrained network grows into a mesh, broadcast operations become rapidly inacceptable in terms of power and bandwidth, and the not-onlink model whereby for the most part hosts do not lookup one another, is mandatory.¶

In all cases, to make the internet greener, we must reconsider the use of broadcast over large access networks. To maintain the capability to build the Subnets we want, the IPv6 architecture must enable to decouple the Subnet from the broadcast domain, make the broadcast domain small and local, and refocus the use of broadcast to the cases where all nodes are interested. Additionally, the IPv6 architecture must enable a model where the network serves and protects low-power devices that sleep most of the time and wake up on their own schedule.¶

2.5. Security and Privacy

Broadcasting ND_Classic messages expose the source and the Target addresses to the whole network, including nodes that do not need to know that those addresses are present in the network. A passive listener may discover the addresses without any observable action or possibility of control by the source. Once it has discovered the presence of neighbor addresses, the onlink attacker can impersonate any host in the network, either by sourcing packets with a stolen address, or by overriding the neighbor caches with a NA that indicates the attacker's link-layer address.¶

It is thus desirable to avoid exposing the host IPv6 address in broadcast ND messages. A more private approach has each node see and connect to only a subset of the routers using the not-onlink model. The source may still shortcut to the destination when the destination is effectively on link, based on redirect messages from the router, when desirable. Additionally, it is desirable that only the address owner can source packets with that address, and that another party may not be able to claim and use that address.¶

The reactive NS lookup method can also be leveraged from the outside of the network to perform DOS attacks on constrained resources in the network. The attacker just needs to forge any random address from the Subnet prefix and send one packet to that random address. The Subnet ingress router will have to store that packet for the duration of the lookup time, and broadcast an NS to lookup the forged address. This both locks memory in the router and consumes bandwidth and energy, impacting all nodes in the Subnet.¶

To avoid the lookup delays and associated attacks, it makes sense to use a proactive method whereby the router knows all the address mappings in advance. When that is achieved, if the destination address of an incoming packet is not present in the router tables, then the destination does not exist in the network and the packet can safely be dropped by the forwarding engine, e.g., in hardware.¶

2.6. More Middleboxes

The above problems have been observed at least since the early 2000s. A number of actions were taken. For instance, IEEE std 802.11 [IEEE Std. 802.11] mandates the support of a middlebox operation called "ARP proxy" for IPv4 and IPv6 in the Access Point (AP). The "ARP Proxy" cancels broadcasts over a BSS when the IP Target of the ARP/ND message is not owned by a STA associated to the AP. With IPv4, the expectation is that the STA owns exactly one IP address, and that the address is obtained via DHCP right after the association, so it is simple and deterministic to snoop the address in the DHCP exchange (as long as it remains in the clear) and cancel undesirable ARP lookups.¶

In contrast to IPv4, IPv6 enables a node to form multiple addresses, some of them temporary and with a particular attention paid to privacy. Addresses may be formed and deprecated asynchronously to the association. Even if the knowledge of IPv6 addresses used by a STA can be obtained by snooping protocols such as ND-Classic and DHCPv6, or by observing data traffic sourced at the STA, such methods provide only an imperfect knowledge of the state of the STA at the AP. This may result in a loss of connectivity for some IPv6 addresses, in particular for addresses rarely used and in a situation of mobility. This may also result in undesirable state persistence in the AP when a STA ceases to use an IPv6 address. It follows that snooping protocols is not a recommended technique and that it should only be used as last resort.¶

Because ND-Classic is so easy to attack, some vendors have deployed undocumented proprietary counter measures as middlebox operation in the switches and routers. Those middleboxes snoop the ND-Classic messages, filter them or modify them, for instance to change their link-layer scope from broadcast to unicast. Based on the snooped information, the middlebox may for instance drop an RA message that appears to be coming from a host (e.g., as inferred because it is received on a wireless adapter), or an NA message coming from a device that does not appear to be the owner. But, for the lack of an explicit contract between the host and the middlebox, the middlebox cannot determine who the real owner is, and it may deny a rightful user.¶

In a managed network, IP addresses are an expensive and thus a limited resource. To ensure a fair use and protect against DOS attacks, the middlebox may also block Stateless address Autoconfiguration (SLAAC) from a host above a fixed number of addresses. When that happens, the host believes that it can use the address but fails to connect with it. This might happen even if the host has ceased to use other addresses and is now within the allowed quota. Classic-ND lacks both a method for the host to know how many addresses it can own, and a method for the router to know which addresses the host uses at any point of time. The infrastructure needs a deterministic knowledge of the addresses in use, and for that a contract must be passed between the host and the network to ensure that the all the addresses are known and usable.¶

Maybe the most insidious side effect of those middleboxes is that as opposed to NAT, their operation is obfuscated and proprietary. From one vendor to the next, and from one product generation to the next, their behavior may evolve and affect ND-Classic in different fashions. In the short term, this may only impact some specific deployments, which may have to work around the issues. In the longer term, this may affect the capability we have to evolve the protocol, like firewalls impact our capability to develop new transports in parallel to TCP and UDP. We must either standardize (e.g., for ND proxy) or eliminate those middlebox activities, and for that, the IPv6 ND protocol must evolve to a model where proprietary middleboxes are not needed anymore. This demands a model that minimizes the use of broadcasts, and where a contract provides mutual guarantees for the host that need IPv6 addresses and the routers that provide reachability and protection for these addresses.¶

2.7. Summary of Issues

ND-Classic inherited 2 majors design points from IPv4, a strong coupling of logical and physical concepts, which creates unacceptable constraints on modern deployments with virtual and intangible links, and a reactive operation for AR and DAD that requires an extensive use of broadcast spanning the Subnet. While IPv4 and IPv6 behaviors are similar for addresses obtained via DHCP, the cost of AR and DAD makes IPv6 significantly more expensive than IPv4 when SLAAC is enabled.¶

And while IPv4 supported NBMA and P2MP models (e.g., on Frame Relay leveraging OSPFv2), the IPv6 promise to support NBMA (for ATM) remains unmet to this day, as only P2P and Transit links are properly supported by ND-Classic. For those reasons, as well as inherent complexity and unpredictability, IPv6 with SLAAC can be significantly less attractive than IPv4 to some network administrators.¶

ND-Classic exposes all addresses to all nodes in the network, which is unfit for privacy. It is prone to DOS attacks from outside the network and impersonation attacks from the inside, with no method to prove the address ownership and perform Source address Validation (SAVI) later on the data traffic. To protect against such threats, the vendors had to introduce middleboxes that interfere with the protocol operation and affect the capability to evolve the protocol in the future.¶

ND-Classic lacks a support for mobility (which typically entails a sequence counter maintained by the host and the deprecation of state that is based on older sequences) and for anycast. This makes it very hard for the network to defend the addresses on behalf of the owner, e.g., when the owner is temporarily disconnected. It results that the operation of the middleboxes is unsatisfactory and may cause discontinuities in connectivity.¶

The extensive use of broadcast operations in ND-Classic is not only detrimental to bandwidth, it is also an issue for energy conservation and sustainability. Devices must be always attached and always powered on to answer NS messages, which makes ND-Classic inapplicable to power-conserving devices such as IoT sensors that sleep for the vast majority of their time.¶

3.1. Basic Concepts

This document introduces an alternate architecture for IPv6 access networks that is designed to apply to the WLANs and LoWPANs types of networks as well as other NBMA networks such as Data-Center overlays and P2MP networks such as IoT radio meshes. It may be used as a replacement to the ND-Classic reactive model in any network where the issues discussed in Section 2 are detrimental to the network operation.¶

The key design points in this architecture derive from the original observations made at the 6LoWPAN WG for constrained devices and networks, and focus on avoiding waste of limited resources such as spectrum and energy, by using broadcasts only when broadcast is really needed, and decoupling the IP abstraction of a Subnet from the broadcast domains to avoid Subnet-wide broadcast storms. To that effect, this architecture leverages the not-onlink model and routing inside the Subnet, which enables to form potentially large MLSNs without creating a large broadcast domain at the link layer.¶

To support the deployment agility that virtual (e.g., VxLAN overlays and pseudowires) and intangible (e.g., wireless, laser, and quantum) links enable, the IP abstractions of Interface, Link, and Subnet are decoupled from their classical physical counterparts of port, link, and broadcast domains. The Subnet is defined by a prefix length called Subnet Prefix Length (SPL), as the longest aggregation that can be advertised in the IGP. An SPL of 64 is typical though the architecture does not mandate it. Host routes and prefixes longer than SPL are advertised inside the Subnet only, using a separate Subnet Gateway protocol (SGP).¶

Any device that owns an address within the Subnet prefix belongs to the Subnet, this is now decoupled from the physical connectivity and broadcast domain. Instead, the IPv6 routers that serve a Subnet must form a connected dominating set such that every host in the Subnet is connected to at least one router and the routers are connected to one another directly (classical NBMA, aka full mesh) or indirectly via other routers (Point to MultiPoint, P2MP, aka partial mesh). The not-onlink model is used throughout, so hosts do not look each other up, saving all the associated broadcast. Instead, they rely on the routers to forward the packets inside and outside the Subnet. This way, the Subnet can have any structure needed for the deployment, where hosts can move from router to router in the Subnet, or anywhere in the Internet provided they can lay a mobility tunnel to one of the routers for use as IP Link to the Subnet.¶

All IP Links are abstracted as Point-to-Point, though a lower-layer broadcast service may be used by the router to send RAs to a subset of local hosts in the Subnet, or by the host to send an RS message to a subset of the routers. An IP Interface bundles one or more subInterfaces, one per Subnet that can be reached through that Interface. A Global IPv6 address is installed on the subInterface that connects to the Subnet from which the address derives. The IP Interface connects to one or more IP Links (to different neighbors) over the same or over different physical ports (they are decoupled). A link-local address is associated to the IP Link directly. Each SubInterface connects to the subset of those IP Links that reach other nodes in the Subnet.¶

In a fashion similar to a IEEE std 802.11 [IEEE Std. 802.11] Association, IPv6 nodes register their addresses to one or more neighbor router(s), which may reject the registration, e.g., in case of a duplication. With the registration, the routers collectively build a complete knowledge of the hosts they serve and in return, hosts obtain guaranteed routing services for their registered addresses for a contractual lifetime.¶

To support distributed routers in the Subnet, an abstract registrar service maintains the state of all active registrations in the Subnet and answers queries to lookup mappings, validate ownership, and avoid duplications. The registration is abstract to the routing service and the registrar service, and it can be protected to prevent impersonation attacks. The registration enables the network to know deterministically all the IPv6 addresses and link-layer address mapping currently in use, and eliminates the need for lookups and DAD, and for the associated broadcasts.¶

The abstract routing service allows an ingress router to find a path to the destination address within the Subnet. It can be a simple reflection in a Hub-and-Spoke Subnet that emulates an IEEE Std. 802.11 Infrastructure BSS at the network layer. It can also be a full-fledge routing protocol, e.g., RPL (see [RFC9010]), which is designed to adapt to various LLNs such as WLAN and WPAN radio meshes, or RIFT (see [I-D.ietf-rift-rift]) or BGP/EVPN (see [RFC8365]), for application in data centers. It can be based on overlay tunnels between ingress router and egress router leveraging a resolver service such as LISP, see [RFC7834] for more. Finally, the routing service can also be an ND proxy that emulates an IEEE Std. 802.11 Infrastructure ESS at the network layer, as specified in the IPv6 Backbone Router [RFC8929].¶

The abstract registrar service maintains the mapping between the registered node link-layer address and the registered IPv6 address. It contains meta data that enables to ascertain that the second registration for the same address is performed for the same registered node, so it also binds the registered node with the registered IPv6 address. The registrar service provides APIs to look up a link-layer address for an IPv6 address as well as validate IPv6 address ownership. The registrar can be implemented as a mapping server ala LISP [RFC6830], a distributed state ala ND proxy [RFC8929], or a synchronized state ala EVPN [RFC7432]. In the former case, this enables the reactive lookups to be performed as unicast requests to the map resolver. In the latter, the address mapping is synchronized by the routing protocol and known to all the routers for all nodes in the IP Subnet, so there is never a need for a reactive lookup.¶

On the one hand, the Architecture proposed in this document avoids the use of broadcast operation for DAD and AR, and on the other hand, it supports use cases where Subnet and link-layer domains are not congruent, which is common in wireless networks unless a specific link-layer emulation is provided.¶

The address registration establishes a contract between the nodes and the routers where nodes can ask for addresses which will be guaranteed to be operational for a contractual lifetime, and the network may accept or refuse granting additional addresses based on state (e.g., duplicate address) as well as policy (e.g., quota). This ways hosts and routers agree deterministically on which addresses will be served to which nodes in the Subnet. The registration is agnostic to the router to router and router to registrar interfaces. The latter interface can be implemented in various fashions that can blend in existing technologies such as legacy ND-Classic network through ND proxy, as well as EVPN-based and LISP-based overlays.¶

3.2. Acronyms

This document uses the following abbreviations:¶

6BBR:

6LoWPAN Backbone Router¶

6LN:

6LoWPAN Node¶

6LR:

6LoWPAN Router¶

ARO:

address Registration Option¶

BGP:

Border Gateway Protocol¶

DAC:

Duplicate address Confirmation (message)¶

DAD:

Duplicate address Detection¶

DAR:

Duplicate address Request (message)¶

EDAC:

Extended Duplicate address Confirmation¶

EDAR:

Extended Duplicate address Request¶

EVPN:

Ethernet VPN¶

IGP:

Interior Gateway Protocol¶

LAN:

Local Area Network¶

LISP:

Locator/ID Separation Protocol¶

LLN:

Low-Power and Lossy Network¶

LLA:

link-local address¶

LoWPAN:

Low-Power WPAN¶

MAC:

Medium Access Control¶

MLSN:

Multi-link Subnet¶

MLD:

multicast Listener Discovery¶

NA:

Neighbor Advertisement (message)¶

NBMA:

Non-Broadcast Multi-Access¶

NCE:

Neighbor Cache Entry¶

ND:

Neighbor Discovery (protocol)¶

NDP:

Neighbor Discovery Protocol¶

NS:

Neighbor Solicitation (message)¶

P2P:

Point-to-Point¶

P2MP:

Point-to-Multipoint¶

RPL:

IPv6 Routing Protocol for LLNs¶

RA:

Router Advertisement (message)¶

RS:

Router Solicitation (message)¶

SGP:

Subnet Gateway Protocol¶

SPL:

Subnet Prefix Length¶

ULP:

Upper-Layer Protocol¶

VLAN:

Virtual LAN¶

VxLAN:

Virtual Extensible LAN¶

VPN:

Virtual Private Network¶

WAN:

Wide Area Network¶

WiND:

Wireless Neighbor Discovery (protocol)¶

WLAN:

Wireless Local Area Network¶

WPAN:

Wireless Personal Area Network¶

3.3. Terminology

+--------------------
|
|   IP Link 1 ---------------------------> Node 1
       link-layer address MAC1             link-layer address MAC3
|      link-local address LLA1             link-local address LLAN1
|
|   IP Link 2 ---------------------------> Node 2
       link-layer address MAC2             link-layer address MAC4
|      link-local address LLA2             link-local address LLAN2
|                ...
|
|             (LLA 1 may be the same as LLA 2)
+--------------------
      network port

+--------------------
|
|   IP SubInterface a  ------------------> IP Link A
|      IP Subnet a::/64                    IP Link B
|         IP Addresses a::1 .. a::n           ...
|                                          IP Link N
|
|   IP SubInterface b  ------------------> IP Link A
|      IP Subnet b::/64                    IP Link D
|         IP Addresses b::1 .. b::n           ...
|                                          IP Link P
|                ...
|
|  (Link A and B may be attached to different network ports)
|  (Link A may belong to both subInterfaces a and b)
|
+--------------------
      IP Interface, using SPL=64

+--------------------
|                                              router 4
|                                              ^    ^
| +----------------------------------+      /       |
| |      L2 broadcast domain        IP Link     IP Link
| |                               /  |              |
| |                            v     |              v
| |  router1 <--IP Link--> router 2 <--IP Link--> router 3
| |    ^  ^                 ^  ^     |              ^
| |    |    \             /    |     |              |
| | IP Link IP Link IP Link IP Link  |          IP Link
| |    |       \      /        |     |              |
| |    v         v  v          v     |              v
| |  host 1     host 2       host 3  |           host 4
| |                                  |
| +----------------------------------+
|
|  (Different IP Links may be sustained by different media)
|
+--------------------

      IP Subnet

3.5. Stateful address Autoconfiguration and Subnet Routing

This Architecture defines a new operation for ND that is based on 2 major paradigm changes, a proactive address registration by hosts to their attachment routers and routing to host routes (/128) within the Subnet. This allows ND to avoid the expectations of transit links and Subnet-wide broadcast domains.¶

The proactive address registration, called Stateful address Autoconfiguration (SFAAC) by opposition to SLAAC, is agnostic to the method used for address Assignment, e.g., Manual, Semantically Opaque Autoconfiguration [RFC7217], randomized [RFC8981], or DHCPv6 [RFC8415]. It does not change the IPv6 addressing [RFC4291] or the current practices of assigning prefixes, with typically a SPL of 64, to a Subnet. But the DAD operation is performed as a unicast exchange with the abstract egistrar service.¶

This Architecture combines SFAAC with the not-onlink model on the IP Interfaces. Hosts do not expect the IP Subnet to be reachable over the L2 broadcast domain and rely on their routers to forward the packets inside and outside the Subnet. In turn, the router expose to each other all the IPv6 addresses that are either owned or registered to it as host routes over a Subnet Gateway Protocol, a routing protocol that is specialized in routing inside the Subnet and can be decoupled with the IGP, that is the routing protocol used between subnets.¶