Internet-Draft | IPv6 over OMNI Interfaces | November 2021 |
Templin & Whyman | Expires 19 May 2022 | [Page] |
Mobile network platforms and devices (e.g., aircraft of various configurations, terrestrial vehicles, seagoing vessels, enterprise wireless devices, pedestrians with cell phones, etc.) communicate with networked correspondents over multiple access network data links and configure mobile routers to connect end user networks. A multilink interface specification is presented that enables mobile nodes to coordinate with a network-based mobility service and/or with other mobile node peers. This document specifies the transmission of IP packets over Overlay Multilink Network (OMNI) Interfaces.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 19 May 2022.¶
Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.¶
Mobile network platforms and devices (e.g., aircraft of various configurations, terrestrial vehicles, seagoing vessels, enterprise wireless devices, pedestrians with cellphones, etc.) configure mobile routers with multiple interface connections to wireless and/or wired-line data links. These data links may have diverse performance, cost and availability properties that can change dynamically according to mobility patterns, flight phases, proximity to infrastructure, etc. The mobile router acts as a Client of a network-based Mobility Service (MS) by configuring a virtual interface over its underlying interface data link connections to support the "6M's of modern Internetworking" (see below).¶
Each Client configures a virtual interface (termed the "Overlay Multilink Network Interface (OMNI)") as a thin layer over its underlying interfaces. The OMNI interface is therefore the only interface abstraction exposed to the IP layer and behaves according to the Non-Broadcast, Multiple Access (NBMA) interface principle, while underlying interfaces appear as link layer communication channels in the architecture. The OMNI interface internally employs the "OMNI Adaptation Layer (OAL)" to ensure that original IP packets are delivered without loss due to size restrictions. The OMNI interface connects to a virtual overlay service known as the "OMNI link". The OMNI link spans one or more Internetworks that may include private-use infrastructures and/or the global public Internet itself.¶
The Client's OMNI interface interacts with the MS and/or other Clients through IPv6 Neighbor Discovery (ND) control message exchanges [RFC4861]. The MS consists of a distributed set of service nodes known as Proxy/Servers (and other infrastructure elements) that also configure OMNI interfaces. An example MS termed "Automatic Extended Route Optimization (AERO)" appears in [I-D.templin-6man-aero]. In terms of precedence, the AERO specification may provide first-principle insights into a representative mobility service architecture as useful context for this specification.¶
Each OMNI interface provides a multilink nexus for exchanging inbound and outbound traffic via selected underlying interface(s). The IP layer sees the OMNI interface as a point of connection to the OMNI link. Each OMNI link has one or more associated Mobility Service Prefixes (MSPs), which are typically IP Global Unicast Address (GUA) prefixes assigned to the link and from which Mobile Network Prefixes (MNPs) are derived. If there are multiple OMNI links, the IP layer will see multiple OMNI interfaces.¶
Each Client receives an MNP through IPv6 ND control message exchanges with Proxy/Servers. The Client uses the MNP for numbering downstream-attached End User Networks (EUNs) independently of the access network data links selected for data transport. The Client acts as a mobile router on behalf of its EUNs, and uses OMNI interface control messaging to coordinate with Proxy/Servers and/or other Clients. The Client iterates its control messaging over each of the OMNI interface's underlying interfaces in order to register each interface with the MS (see Section 15).¶
Clients may connect to multiple distinct OMNI links within the same OMNI domain by configuring multiple OMNI interfaces, e.g., omni0, omni1, omni2, etc. Each OMNI interface is configured over a set of underlying interfaces and provides a nexus for Safety-Based Multilink (SBM) operation. Each OMNI interface within the same OMNI domain configures a common ULA prefix [ULA]::/48, and configures a unique 16-bit Subnet ID '*' to construct the sub-prefix [ULA*]::/64 (see: Section 9). The IP layer applies SBM routing to select a specific OMNI interface, then the selected OMNI interface applies Performance-Based Multilink (PBM) internally to select appropriate underlying interfaces. Applications select SBM topologies based on IP layer Segment Routing [RFC8402], while each OMNI interface orchestrates PBM internally based on OMNI layer Segment Routing.¶
OMNI provides a link model suitable for a wide range of use cases. In particular, the International Civil Aviation Organization (ICAO) Working Group-I Mobility Subgroup is developing a future Aeronautical Telecommunications Network with Internet Protocol Services (ATN/IPS) and has issued a liaison statement requesting IETF adoption [ATN] in support of ICAO Document 9896 [ATN-IPS]. The IETF IP Wireless Access in Vehicular Environments (ipwave) working group has further included problem statement and use case analysis for OMNI in a document now in AD evaluation for RFC publication [I-D.ietf-ipwave-vehicular-networking]. Still other communities of interest include AEEC, RTCA Special Committee 228 (SC-228) and NASA programs that examine commercial aviation, Urban Air Mobility (UAM) and Unmanned Air Systems (UAS). Pedestrians with handheld devices represent another large class of potential OMNI users.¶
OMNI supports the "6M's of modern Internetworking" including:¶
This document specifies the transmission of IP packets and control messages over OMNI interfaces. The OMNI interface supports either IP protocol version (i.e., IPv4 [RFC0791] or IPv6 [RFC8200]) as the network layer data plane, while using IPv6 ND messaging as the control plane independently of the data plane IP protocol(s). The OAL operates as a sublayer between L3 and L2 based on IPv6 encapsulation [RFC2473] as discussed in the following sections.¶
The terminology in the normative references applies; especially, the terms "link" and "interface" are the same as defined in the IPv6 [RFC8200] and IPv6 Neighbor Discovery (ND) [RFC4861] specifications. Additionally, this document assumes the following IPv6 ND message types: Router Solicitation (RS), Router Advertisement (RA), Neighbor Solicitation (NS), Neighbor Advertisement (NA) and Redirect. Clients and Proxy/Servers that implement IPv6 ND maintain per-neighbor state in Neighbor Cache Entries (NCEs). Each NCE is indexed by the neighbor's Link-Local Address (LLA), while the Unique-Local Address (ULA) used for encapsulation provides context for Identification verification.¶
The Protocol Constants defined in Section 10 of [RFC4861] are used in their same format and meaning in this document. The terms "All-Routers multicast", "All-Nodes multicast" and "Subnet-Router anycast" are the same as defined in [RFC4291] (with Link-Local scope assumed).¶
The term "IP" is used to refer collectively to either Internet Protocol version (i.e., IPv4 [RFC0791] or IPv6 [RFC8200]) when a specification at the layer in question applies equally to either version.¶
The following terms are defined within the scope of this document:¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119][RFC8174] when, and only when, they appear in all capitals, as shown here.¶
An implementation is not required to internally use the architectural constructs described here so long as its external behavior is consistent with that described in this document.¶
An OMNI interface is a virtual interface configured over one or more underlying interfaces, which may be physical (e.g., an aeronautical radio link, etc.) or virtual (e.g., an Internet or higher-layer "tunnel"). The OMNI interface architectural layering model is the same as in [RFC5558][RFC7847], and augmented as shown in Figure 1. The IP layer therefore sees the OMNI interface as a single L3 interface nexus for multiple underlying interfaces that appear as L2 communication channels in the architecture.¶
+----------------------------+ | Upper Layer Protocol | Session-to-IP +---->| | Address Binding | +----------------------------+ +---->| IP (L3) | IP Address +---->| | Binding | +----------------------------+ +---->| OMNI Interface | Logical-to- +---->| (OMNI Adaptation Layer) | Physical | +----------------------------+ Interface +---->| L2 | L2 | | L2 | Binding |(IF#1)|(IF#2)| ..... |(IF#n)| +------+------+ +------+ | L1 | L1 | | L1 | | | | | | +------+------+ +------+
Each underlying interface provides an L2/L1 abstraction according to one of the following models:¶
The OMNI interface forwards original IP packets from the network layer (L3) using the OMNI Adaptation Layer (OAL) (see: Section 5) as an encapsulation and fragmentation sublayer service. This "OAL source" then further encapsulates the resulting OAL packets/fragments in *NET headers to create "carrier packets" for transmission over underlying interfaces (L2/L1). The target OMNI interface receives the carrier packets from underlying interfaces (L1/L2) and discards the *NET headers. If the resulting OAL packets/fragments are addressed to itself, the OMNI interface acts as an "OAL destination" and performs reassembly if necessary, discards the OAL encapsulation, and delivers the original IP packet to the network layer (L3). If the OAL fragments are addressed to another node, the OMNI interface instead acts as an "OAL intermediate node" by re-encapsulating in new *NET headers and forwarding the new carrier packets over an underlying interface without reassembling or discarding the OAL encapsulation. The OAL source and OAL destination are seen as "neighbors" on the OMNI link, while OAL intermediate nodes provide a virtual bridging service that joins the segments of a (multinet) Segment Routing Topology (SRT).¶
The OMNI interface can send/receive original IP packets to/from underlying interfaces while including/omitting various encapsulations including OAL, UDP, IP and L2. The network layer can also access the underlying interfaces directly while bypassing the OMNI interface entirely when necessary. This architectural flexibility may be beneficial for underlying interfaces (e.g., some aviation data links) for which encapsulation overhead may be a primary consideration. OMNI interfaces that send original IP packets directly over underlying interfaces without invoking the OAL can only reach peers located on the same OMNI link segment. Source Clients can instead use the OAL to coordinate with target Clients in the same or different OMNI link segments by sending initial carrier packets to a First-Hop Segment (FHS) Proxy/Server. The FHS Proxy/Sever then forwards the packets into the SRT spanning tree, which transports them to a Last-Hop Segment (LHS) Proxy/Server for the target Client.¶
Original IP packets sent directly over underlying interfaces are subject to the same path MTU related issues as for any Internetworking path, and do not include per-packet identifications that can be used for data origin verification and/or link-layer retransmissions. Original IP packets presented directly to an underlying interface that exceed the underlying network path MTU are dropped with an ordinary ICMPv6 Packet Too Big (PTB) message returned. These PTB messages are subject to loss [RFC2923] the same as for any non-OMNI IP interface.¶
The OMNI interface encapsulation/decapsulation layering possibilities are shown in Figure 2 below. Imaginary vertical lines drawn between the Network Layer and Underlying interfaces in the figure denote the encapsulation/decapsulation layering combinations possible. Common combinations include NULL (i.e., direct access to underlying interfaces with or without using the OMNI interface), IP/IP, IP/UDP/IP, IP/UDP/IP/L2, IP/OAL/UDP/IP, IP/OAL/UDP/L2, etc.¶
+------------------------------------------------------------+ | Network Layer (Original IP packets) | +--+---------------------------------------------------------+ | OMNI Interface (virtual sublayer nexus) | +--------------------------+------------------------------+ | OAL Encaps/Decaps | +------------------------------+ | OAL Frag/Reass | +------------+---------------+--------------+ | UDP Encaps/Decaps/Compress | +----+---+------------+--------+--+ +--------+ | IP E/D | | IP E/D | | IP E/D | +---+------+-+----+ +--+---+----+ +----+---+--+ |L2 E/D| |L2 E/D| |L2 E/D| |L2 E/D| +-------+------+---+------+----+------+---------------+------+ | Underlying Interfaces | +------------------------------------------------------------+
The OMNI/OAL model gives rise to a number of opportunities:¶
Note that even when the OMNI virtual interface is present, applications can still access underlying interfaces either through the network protocol stack using an Internet socket or directly using a raw socket. This allows for intra-network (or point-to-point) communications without invoking the OMNI interface and/or OAL. For example, when an IPv6 OMNI interface is configured over an underlying IPv4 interface, applications can still invoke IPv4 intra-network communications as long as the communicating endpoints are not subject to mobility dynamics.¶
Figure 3 depicts the architectural model for a source Client with an attached EUN connecting to the OMNI link via multiple independent *NETs. The Client's OMNI interface sends IPv6 ND messages over available underlying interfaces to FHS Proxy/Servers using any necessary *NET encapsulations. The IPv6 ND messages traverse the *NETs until they reach an FHS Proxy/Server (FHS#1, FHS#2, ..., FHS#n), which returns an IPv6 ND message response and/or forwards a proxyed version of the message over the SRT to an LHS Proxy/Server near the target Client (LHS#1, LHS#2, ..., LHS#m). The Hop Limit in IPv6 ND messages is not decremented due to encapsulation; hence, the source and target Client OMNI interfaces appear to be attached to a common link.¶
+--------------+ (:::)-. |Source Client |<-->.-(::EUN:::) +--------------+ `-(::::)-' |OMNI interface| +----+----+----+ +--------|IF#1|IF#2|IF#n|------ + / +----+----+----+ \ / | \ / | \ v v v (:::)-. (:::)-. (:::)-. .-(::*NET:::) .-(::*NET:::) .-(::*NET:::) `-(::::)-' `-(::::)-' `-(::::)-' +-----+ +-----+ +-----+ ... |FHS#1| ......... |FHS#2| ......... |FHS#n| ... . +--|--+ +--|--+ +--|--+ . . | | | . \ v / . . \ / . . v (:::)-. v . . .-(::::::::) . . .-(::: Segment :::)-. . . (::::: Routing ::::) . . `-(:: Topology ::)-' . . `-(:::::::-' . . / | \ . . / | \ . . v v v . +-----+ +-----+ +-----+ . ... |LHS#1| ......... |LHS#2| ......... |LHS#m| ... +--|--+ +--|--+ +--|--+ \ | / v v v <-- Target Clients -->
After the initial IPv6 ND message exchange, the source Client (and/or any nodes on its attached EUNs) can send packets to the target Client over the OMNI interface. OMNI interface multilink services will forward the packets via FHS Proxy/Servers for the correct underlying *NETs. The FHS Proxy/Server then forwards them over the SRT which delivers them to an LHS Proxy/Server, and the LHS Proxy/Server in turn forwards the packets to the target Client. (Note that when the source and target Client are on the same SRT segment, the FHS and LHS Proxy/Servers may be one and the same.)¶
Clients select a Hub Proxy/Server (not shown in the figure), which will often be one of their FHS Proxy/Servers but could also be any Proxy/Server on the OMNI link. Clients then register all of their underlying interfaces with the Hub Proxy/Server via the FHS Proxy/Server in a pure proxy role. The Hub Proxy/Server then provides a designated router service for the Client, and the Client can quickly migrate to a new Hub Proxy/Server if the first becomes unresponsive.¶
Clients therefore use Proxy/Servers as gateways into the SRT to reach OMNI link correspondents via a spanning tree established in a manner outside the scope of this document. Proxy/Servers forward critical MS control messages via the secured spanning tree and forward other messages via the unsecured spanning tree (see Security Considerations). When route optimization is applied as discussed in [I-D.templin-6man-aero], Clients can instead forward directly to an SRT intermediate node themselves (or directly to correspondents in the same SRT segment) to reduce Proxy/Server load.¶
The OMNI interface observes the link nature of tunnels, including the Maximum Transmission Unit (MTU), Maximum Reassembly Unit (MRU) and the role of fragmentation and reassembly [I-D.ietf-intarea-tunnels]. The OMNI interface is configured over one or more underlying interfaces as discussed in Section 4, where the interfaces (and their associated *NET paths) may have diverse MTUs. OMNI interface considerations for accommodating original IP packets of various sizes are discussed in the following sections.¶
IPv6 underlying interfaces are REQUIRED to configure a minimum MTU of 1280 octets and a minimum MRU of 1500 octets [RFC8200]. Therefore, the minimum IPv6 path MTU is 1280 octets since routers on the path are not permitted to perform network fragmentation even though the destination is required to reassemble more. The network therefore MUST forward original IP packets of at least 1280 octets without generating an IPv6 Path MTU Discovery (PMTUD) Packet Too Big (PTB) message [RFC8201]. (While the source can apply "source fragmentation" for locally-generated IPv6 packets up to 1500 octets and larger still if it knows the destination configures a larger MRU, this does not affect the minimum IPv6 path MTU.)¶
IPv4 underlying interfaces are REQUIRED to configure a minimum MTU of 68 octets [RFC0791] and a minimum MRU of 576 octets [RFC0791][RFC1122]. Therefore, when the Don't Fragment (DF) bit in the IPv4 header is set to 0 the minimum IPv4 path MTU is 576 octets since routers on the path support network fragmentation and the destination is required to reassemble at least that much. The OMNI interface therefore MUST set DF to 0 in the IPv4 encapsulation headers of carrier packets that are no larger than 576 octets, and SHOULD set DF to 1 in larger carrier packets unless it has a way to determine the encapsulation destination MRU and has carefully considered the issues discussed in Section 6.10.¶
The OMNI interface performs OAL encapsulation by appending an IPv6 header with extenstions that may include a Routing Header of no more than 40-octets followed by an 8-octet Fragment Header and with a 2-octet trailing checksum (see: Section 6). The IPv6 Payload Length and Fragment Offset fields therefore limit the maximum-sized original IP packet that can be accommodated as multiple fragments (i.e., the OMNI interface MTU) to (2**16 - 1) minus the extension lengths calculated as:¶
while the MRU is set to the fixed size (2**16 - 1) since reassembly must account for the lengths of the extensions. The MTU/MRU sizes are therefore not a reflection of the underlying interface or *NET path MTUs, but rather determine the largest original IP packet the OAL (and/or underlying interface) can forward or reassemble as multiple fragments.¶
As for any IP interface the OMNI interface MAY set a smaller MTU value to a minimum of 1280 for IPv6 or 576 for IPv4. For each OAL destination (i.e., for each OMNI link neighbor), the OAL source may discover smaller Reassembly Limit values based on receipt of IPv6 ND advertisement messages (see: Section 12.2.10). The OMNI interface employs the OAL as an encapsulation sublayer service to transform original IP packets into OAL packets/fragments, and the OAL in turn uses *NET encapsulation to forward carrier packets over the underlying interfaces (see: Section 6).¶
While the OAL only supports multi-fragment fragmentation and reassembly for original IPv6 packets no larger than 65485 octets, OMNI interfaces can forward larger packets as an OAL "atomic fragment" through the application of IPv6 Jumbograms [RFC2675]. OMNI interfaces that support jumbograms can set an IPv6 MTU larger than 65485 octets up to a maximum of (2**32 - 1) minus OAL extension lengths.¶
For packets larger than 65485 octets, the OMNI interface performs OAL encapsulation by appending an IPv6 header, followed by an 8-octet Hop-By-Hop extension header with Jumbo Payload option, followed possibly by a Routing header of no more than 40-octets, followed by an 8-octet Fragment Header and with a 2-octet trailing checksum.¶
The OMNI interface then forwards the OAL packet as a singular atomic fragment if possible; otherwise, it drops the packet and returns a PTB "hard error". OMNI interfaces that are capable of generating such PTB messages for large packets while accommodating smaller packets with fragmentation if necessary may consider the OMNI interface MTU as "unlimited".¶
When an OMNI interface forwards an original IP packet from the network layer for transmission over one or more underlying interfaces, the OMNI Adaptation Layer (OAL) acting as the OAL source drops the packet and returns a PTB message if the packet exceeds the MRU and/or the Reassembly Limit for the intended OAL destination. Otherwise, the OAL source applies encapsulation to form OAL packets subject to fragmentation producing OAL fragments suitable for *NET encapsulation and transmission as carrier packets over underlying interfaces as described in Section 6.1.¶
These carrier packets travel over one or more underlying networks spanned by OAL intermediate nodes in the SRT, which re-encapsulate by removing the *NET headers of the first underlying network and appending *NET headers appropriate for the next underlying network in succession. (This process supports the multinet concatenation capability needed for joining multiple diverse networks.) After re-encapsulation by zero or more OAL intermediate nodes, the carrier packets arrive at the OAL destination.¶
When the OAL destination receives the carrier packets, it discards the *NET headers and reassembles the resulting OAL fragments into an OAL packet as described in Section 6.3. The OAL destination then decapsulates the OAL packet to obtain the original IP packet, which it then delivers to the network layer. The OAL source may be either the source Client or its FHS Proxy/Server, while the OAL destination may be either the LHS Proxy/Server or the target Client. Proxy/Servers (and other SRT infrastructure node types such as those discussed in [I-D.templin-6man-aero]) may also serve as OAL intermediate nodes.¶
The OAL presents an OMNI sublayer abstraction similar to ATM Adaptation Layer 5 (AAL5). Unlike AAL5 which performs segmentation and reassembly with fixed-length 53 octet cells over ATM networks, however, the OAL uses IPv6 encapsulation, fragmentation and reassembly with larger variable-length cells over heterogeneous underlying networks. Detailed operations of the OAL are specified in the following sections.¶
When the network layer forwards an original IP packet into the OMNI interface, the OAL source inserts an OAL header consisting of an IPv6 encapsulation header followed possibly by a Routing Header followed by a Fragment Header (see [RFC2473] and below) but does not decrement the Hop Limit/TTL of the original IP packet since encapsulation occurs at a layer below IP forwarding. The OAL source copies the "Type of Service/Traffic Class" [RFC2983] and "Congestion Experienced" [RFC3168] values in the original packet's IP header into the corresponding fields in the OAL header, then sets the OAL header "Flow Label" as specified in [RFC6438]. The OAL source finally sets the OAL header IPv6 Hop Limit to a conservative value sufficient to enable loop-free forwarding over multiple concatenated OMNI link segments and sets the Payload Length to the length of the original IP packet.¶
The OAL next selects source and destination addresses for the IPv6 header of the resulting OAL packet. Client OMNI interfaces set the OAL header source address to a Unique Local Address (ULA) based on the Mobile Network Prefix (MNP-ULA), while Proxy/Server OMNI interfaces set the source address to an Administrative ULA (ADM-ULA) (see: Section 9). When a Client OMNI interface does not (yet) have an MNP-ULA, it can use a Temporary ULA and/or Host Identity Tag (HIT) instead (see: Section 22) as OAL addresses. (In addition to ADM-ULAs, Proxy/Servers also process packets with anycast and/or multicast OAL addresses.)¶
Following OAL encapsulation and address selection, the OAL source next appends a 2 octet trailing Checksum field (initialized to 0) at the end of the original IP packet by incrementing the OAL header IPv6 Payload Length field to reflect the addition of the trailer. The format of the resulting OAL packet following encapsulation is shown in Figure 4:¶
+----------+-----+-----+-----+-----+-----+-----+----+ |OAL Header| Original IP packet |Csum| +----------+-----+-----+-----+-----+-----+-----+----+
The OAL source next selects a 32-bit Identification value for the packet to place in the Fragment Header as specified in Section 6.6 then calculates an OAL checksum using the algorithm specified in Appendix A. The OAL source calculates the checksum over the OAL packet beginning with a pseudo-header of the OAL header similar to that found in Section 8.1 of [RFC8200], followed by the Original IP packet and extending to the end of the (0-initialized) Checksum trailer. The OAL pseudo-header is formed as shown in Figure 5:¶
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + + | | + OAL Source Address + | | + + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + + | | + OAL Destination Address + | | + + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | OAL Payload Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where OAL Payload Length is a 32b-bit value that encodes the lengths of the extension headers, original packet and trailing checksum and Identification is taken from the Fragment Header. (Note that the remaining OAL IPv6, Hob-By-Hop Header, Routing Header and Fragment Header fields are considered mutable information that may change in transit and therefore are not covered by the checksum.)¶
After calculating the checksum, the OAL source next fragments the OAL packet if necessary while assuming the IPv4 minimum path MTU (i.e., 576 octets) as the worst case for OAL fragmentation regardless of the underlying interface IP protocol version since IPv6/IPv4 protocol translation and/or IPv6-in-IPv4 encapsulation may occur in any *NET path. By always assuming the IPv4 minimum even for IPv6 underlying interfaces, the OAL source may produce smaller fragments with additional encapsulation overhead but will always interoperate and never run the risk of loss due to an MTU restriction or due to presenting an underlying interface with a carrier packet that exceeds its MRU. Additionally, the OAL path could traverse multiple SRT segments with intermediate OAL forwarding nodes performing re-encapsulation where the *NET encapsulation of the previous segment is replaced by the *NET encapsulation of the next segment which may be based on a different IP protocol version and/or encapsulation sizes.¶
The OAL source therefore assumes a default minimum path MTU of 576 octets at each SRT segment for the purpose of generating OAL fragments for *NET encapsulation and transmission as carrier packets. Each successive SRT intermediate node may include either a 20 octet IPv4 or 40 octet IPv6 header, an 8 octet UDP header and in some cases an IP security encapsulation (40 octets maximum assumed) during re-encapsulation. Intermediate nodes at any SRT segment may also insert or modify the Routing Header (40 octets maximum) following the 40 octet OAL IPv6 header and preceding the 8 octet Fragment Header. Therefore, assuming a worst case of (40 + 40 + 8) = 88 octets for *NET encapsulation plus (40 + 40 + 8) = 88 octets for OAL encapsulation leaves no less than (576 - 88 - 88) = 400 octets remaining to accommodate a portion of the original IP packet/fragment. The OAL source therefore sets a minimum Maximum Payload Size (MPS) of 400 octets as the basis for the minimum-sized OAL fragment that can be assured of traversing all SRT segments without loss due to an MTU/MRU restriction. The Maximum Fragment Size (MFS) for OAL fragmentation is therefore determined by the MPS plus the size of the OAL encapsulation headers. (Note that the trailing OAL checksum is regarded as ordinary payload data until reassembly and checksum verification are complete.)¶
The OAL source SHOULD maintain "path MPS" values for individual OAL destinations initialized to the minimum MPS and increased to larger values if better information is known or discovered. For example, when *NET peers share a common underlying link or a fixed path with a known larger MTU, the OAL source can set path MPS to this larger size (i.e., greater than 576 octets) as long as the *NET peer reassembles before re-encapsulating and forwarding (while re-fragmenting if necessary). Also, if the OAL source has a way of knowing the maximum *NET encapsulation size for all SRT segments along the path it may be able to increase path MPS to reserve additional room for payload data. Even when OAL header compression is used, the OAL source must include the uncompressed OAL header size in its path MPS calculation since it may need to include a full header at any time.¶
The OAL source can also optimistically set a larger path MPS and/or actively probe individual OAL destinations to discover larger sizes using packetization layer probes in a similar fashion as [RFC4821][RFC8899], but care must be taken to avoid setting static values for dynamically changing paths leading to black holes. The probe involves sending an OAL packet larger than the current path MPS and receiving a small acknowledgement response (with the possible receipt of link-layer error message when a probe is lost). For this purpose, the OAL source can send an NS message with one or more OMNI options with large PadN sub-options (see: Section 12) in order to receive a small NA response from the OAL destination. While observing the minimum MPS will always result in robust and secure behavior, the OAL source should optimize path MPS values when more efficient utilization may result in better performance (e.g. for wireless aviation data links). The OAL source should maintain separate path MPS values for each (source, target) underlying interface pair for the same OAL destination, since different underlying interface pairs may support differing path MPS values.¶
When the OAL source performs fragmentation, it SHOULD produce the minimum number of non-overlapping fragments under current MPS constraints, where each non-final fragment MUST be at least as large as the minimum MPS, while the final fragment MAY be smaller. The OAL source also converts all original IP packets no larger than the current MPS into "atomic fragments" by including a Fragment Header with Fragment Offset and More Fragments both set to 0.¶
OMNI redefines the 1-octet Reserved field in the IPv6 Fragment Header as an integer "Ordinal" value in the most significant 6 bits, followed by a 1-bit "Reserved" flag followed by a 1-bit "ARQ Enabled" flag. For each fragment produced, the OAL source writes a monotonically-increasing value in the Ordinal field and sets the "ARQ Enabled" flag. Specifically, the OAL source writes the ordinal number '0' for the first fragment, '1' for the second fragment, '2' for the third fragment, etc. up to the final fragment or the ordinal value '63', whichever comes first. (The OAL source instead writes the value '0' in the Ordinal field and clears the "ARQ Enabled" flag for any additional fragments.)¶
The OAL source finally encapsulates the fragments in *NET headers to form carrier packets and forwards them over an underlying interface, while retaining the fragments and their ordinal numbers (i.e., #0, #1, #2, etc. up to #63) for a brief period to support link-layer retransmissions (see: Section 6.7). OAL fragment and carrier packet formats are shown in Figure 6.¶
+----------+----------------+ |OAL Header| Frag #0 | +----------+----------------+ +----------+----------------+ |OAL Header| Frag #1 | +----------+----------------+ +----------+----------------+ |OAL Header| Frag #2 | +----------+----------------+ .... +----------+----------------+----+ |OAL Header| Frag #(N-1) |Csum| +----------+----------------+----+ a) OAL fragmentation (Csum in final fragment) +----------+-----+-----+-----+-----+-----+----+ |OAL Header| Original IP packet |Csum| +----------+-----+-----+-----+-----+-----+----+ b) An OAL atomic fragment +--------+----------+----------------+ |*NET Hdr|OAL Header| Frag #i | +--------+----------+----------------+ c) OAL carrier packet after *NET encapsulation
The OAL source or intermediate node encapsulates each OAL fragment (with either full or compressed headers) in *NET encapsulation headers to create a carrier packet. The OAL source or intermediate node (i.e., the *NET source) includes a UDP header as the innermost sublayer if NAT traversal and/or packet filtering middlebox traversal are required; otherwise, the *NET source includes either a full or compressed IP header or a true L2 header (e.g., such as for Ethernet-compatible links). The *NET source then appends any additional encapsulation sublayer headers necessary and presents the resulting carrier packet to an underlying interface, where the underlying network conveys it to a next-hop OAL intermediate node or destination (i.e., the *NET destination).¶
The *NET source encapsulates the OAL information immediately following the *NET innermost sublayer header. If the first four bits of the encapsulated OAL information following the innermost sublayer header encode the value '6', the information must include an uncompressed IPv6 header followed by any IPv6 extension headers followed by upper layer protocol headers and data. Otherwise, the first four bits include a "Type" value, and the OAL information appears in an alternate format as specified in Section 6.4). Alternate formats for Types '0' and '1' are currently specified, while Type value '4' is permanently reserved and all other values are reserved for future use. Carrier packets that contain an unsupported Type value are unconditionally dropped.¶
The OAL node prepares the innermost *NET encapsulation header for OAL packets as follows:¶
When a *NET source includes a UDP header, it SHOULD calculate and include a UDP checksum in carrier packets with full OAL headers to prevent mis-delivery, and MAY disable UDP checksums in carrier packets with compressed OAL headers (see: Section 6.4). If the *NET source discovers that a path is dropping carrier packets with UDP checksums disabled, it should enable UDP checksums in future carrier packets sent to the same *NET destination. If the *NET source discovers that a path is dropping carrier packets that do not include a UDP header, it should include a UDP header in future carrier packets.¶
When a *NET source sends carrier packets with compressed OAL headers and with UDP checksums disabled, mis-delivery due to corruption of the 4-octet Multilink Forwarding Vector Index (MFVI) is possible but unlikely since the corrupted index would somehow have to match valid state in the (sparsely-populated) Multilink Forwarding Information Based (MFIB). In the unlikely event that a match occurs, an OAL destination may receive a mis-delivered carrier packet but can immediately reject packets with an incorrect Identification. If the Identification value is somehow accepted, the OAL destination may submit the mis-delivered carrier packet to the reassembly cache where it will most likely be rejected due to incorrect reassembly parameters. If a reassembly that includes the mis-delivered carrier packets somehow succeeds (or, for atomic fragments) the OAL destination will verify the OAL checksum to detect corruption. Finally, any spurious data that somehow eludes all prior checks will be detected and rejected by end-to-end upper layer integrity checks. See: [RFC6935][RFC6936] for further discussion.¶
For *NET encapsulations over IP, when the *NET source is also the OAL source it next copies the "Type of Service/Traffic Class" [RFC2983] and "Congestion Experienced" [RFC3168] values in the OAL header into the corresponding fields in the *NET IP header, then (for IPv6) set the *NET IPv6 header "Flow Label" as specified in [RFC6438]. The *NET source then sets the *NET IP TTL/Hop Limit the same as for any host (i.e., it does not copy the Hop Limit value from the OAL header) and finally sets the source and destination IP addresses to direct the carrier packet to the next hop. For carrier packets undergoing re-encapsulation, the OAL intermediate node *NET source decrements the OAL header Hop Limit and discards the carrier packet if the value reaches 0. The *NET source then copies the "Type of Service/Traffic Class" and "Congestion Experienced" values from the previous hop *NET encapsulation header into the OAL header, then finally sets the source and destination IP addresses the same as above.¶
Following *NET encapsulation/re-encapsulation, the *NET source sends the resulting carrier packets over one or more underlying interfaces. The underlying interfaces often connect directly to physical media on the local platform (e.g., a laptop computer with WiFi, etc.), but in some configurations the physical media may be hosted on a separate Local Area Network (LAN) node. In that case, the OMNI interface can establish a Layer-2 VLAN or a point-to-point tunnel (at a layer below the underlying interface) to the node hosting the physical media. The OMNI interface may also apply encapsulation at the underlying interface layer (e.g., as for a tunnel virtual interface) such that carrier packets would appear "double-encapsulated" on the LAN; the node hosting the physical media in turn removes the LAN encapsulation prior to transmission or inserts it following reception. Finally, the underlying interface must monitor the node hosting the physical media (e.g., through periodic keepalives) so that it can convey up/down/status information to the OMNI interface.¶
When an OMNI interface receives a carrier packet from an underlying interface, it discards the *NET encapsulation headers and examines the OAL header of the enclosed OAL fragment. If the OAL fragment is addressed to a different node, the OMNI interface (acting as an OAL intermediate node) re-encapsulates and forwards as discussed in Section 6.2. If the OAL fragment is addressed to itself, the OMNI interface (acting as an OAL destination) accepts or drops the fragment based on the (Source, Destination, Identification)-tuple and/or integrity checks.¶
The OAL destination next drops all non-final OAL fragments smaller than the minimum MPS and all fragments that would overlap or leave "holes" smaller than the minimum MPS with respect to other fragments already received. The OAL destination updates a checklist of accepted fragments of the same OAL packet that include an Ordinal number (i.e., Ordinals 0 through 63), but admits all accepted fragments into the reassembly cache. When reassembly is complete, the OAL destination next verifies the OAL packet checksum and discards the packet if the checksum is incorrect. If the OAL packet was accepted, the OAL destination then removes the OAL header/trailer and delivers the original IP packet to the network layer.¶
Carrier packets often travel over paths where all links in the path include CRC-32 integrity checks for effective hop-by-hop error detection for payload sizes up to 9180 octets [CRC], but other paths may traverse links (such as tunnels over IPv4) that do not include adequate integrity protection. The OAL checksum therefore allows OAL destinations to detect reassembly misassociation splicing errors and/or carrier packet corruption caused by unprotected links [CKSUM].¶
The OAL checksum also provides algorithmic diversity with respect to both lower layer CRCs and upper layer Internet checksums as part of a complimentary multi-layer integrity assurance architecture. Any corruption not detected by lower layer integrity checks is therefore very likely to be detected by upper layer integrity checks that use diverse algorithms.¶
OAL sources that send carrier packets with full OAL headers include a CRH-32 extension for segment-by-segment forwarding based on a Multilink Forwarding Information Base (MFIB) in each OAL intermediate node. OAL source, intermediate and destination nodes can instead establish header compression state through IPv6 ND NS/NA message exchanges. After an initial NS/NA exchange, OAL nodes can apply OAL Header Compression to significantly reduce encapsulation overhead.¶
Each OAL node establishes MFIB soft state entries known as Multilink Forwarding Vectors (MVFs) which support both carrier packet forwarding and OAL header compression/decompression. For OAL sources, each MFV is referenced by a single MFV Index (MFVI) that provides compression/decompression and forwarding context for the next hop. For OAL destinations, the MFV is referenced by a single MFVI that provides context for the previous hop. For OAL intermediate nodes, the MFV is referenced by two MFVIs - one for the previous hop and one for the next hop.¶
When an OAL node forwards carrier packets to a next hop, it can include a full OAL header with a CRH-32 extension containing one or more MVFIs. The OAL node can instead omit significant portions of the OAL header (including the CRH-32) while applying OAL header compression. The full or compressed OAL header follows immediately after the innermost *NET encapsulation (i.e., UDP, IP or L2) as discussed in Section 6.2. Two OAL compressed header types (Type '0' and Type '1') are currently specified below.¶
For OAL first-fragments (including atomic fragments), the OAL node uses OMNI Compressed Header - Type 0 (OCH-0) as shown in Figure 7:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Type=0 | Traffic Class | Flow Label | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Next Header | Hop Limit |M| Identification (0-1) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification (2-3) | MFVI (0-1) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MFVI (2-3) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The format begins with a 4-bit Type field set to 0, and is followed by the uncompressed Traffic Class and Flow Label copied from the OAL header, followed by a Next Header field set to the protocol number for the header immediately following the IPv6 Fragment Header. The Next Header field is then followed by a 7-bit compressed Hop Limit field set to the minimum of 127 and the uncompressed OAL IPv6 Hop Limit value. The Hop Limit is then followed by a compressed Fragment Header that includes only the (M)ore Fragments bit and the 4-octet Identification and with all other fields omitted. The compressed Fragment Header is then followed by a 4-octet Multilink Forwarding Vector Index (MFVI).¶
The OAL fragment body is then included immediately following the OCH-0 header, and the *NET header length field is reduced by the difference in length between the compressed headers and full-length IPv6 and Fragment headers. The OCH-0 format applies for first fragments only, which are always regarded as ordinal fragment 0 even though no explicit Ordinal field is included.¶
For OAL non-first fragments (i.e., those with non-zero Fragment Offsets), the OAL uses OMNI Compressed Header - Type 1 (OCH-1) as shown in Figure 8:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Type=1 | Ordinal |M| Fragment Offset | Id(0) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification (1-3) | MFVI(0) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MFVI (1-3) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The format begins with a Type field set to 1 and the IPv6 header is omitted entirely. The Type field is then followed by a compressed IPv6 Fragment Header with a 6-bit Ordinal number field, and with ((M)ore Fragments/Fragment Offset/Identification) copied from the uncompressed fragment header. The compressed Fragment Header is then followed by a 4-octet MFVI.¶
The OAL fragment body is then included immediately following the OCH-1 header, and the *NET header length field is reduced by the difference in length between the compressed headers and full-length IPv6 and Fragment headers. The OCH-1 format applies for non-first fragments only; therefore, Ordinal is set to a monotonically increasing value beginning with 1 for the first non-first fragment, 2 for the second non-first fragment, etc., up to and including the final fragment. If more than 64 fragments are included, the Ordinal value for all fragments beyond the 64th is instead set to 0.¶
When an OAL destination or intermediate node receives a carrier packet, it determines the length of the encapsulated OAL information by examining the length field of the innermost *NET header, verifies that the appropriate *NET header next header field indicates OMNI (see: Section 6.2), then examines the first four bits immediately following the *NET header. If the bits contain the value 6, the OAL node processes the remainder as an uncompressed OAL header. If the bits contain the value 0 or 1, the OAL node instead processes the remainder of the header as an OCH-0 or OCH-1, respectively.¶
For carrier packets with OCH-0/1 or full OAL headers addressed to itself and with CRH-32 extensions, the OAL node then uses the MFVI to locate the cached MFV which determines the next hop. During forwarding, the OAL node changes the MFVI to the cached value for the MVF next hop. If the OAL node is the destination, it instead reconstructs the full OAL headers then adds the resulting OAL fragment to the reassembly cache if the Identification is acceptable. For carrier packets with OCH-1 headers that do not include Traffic Class, Flow Label, Next Header or Hop Limit information, the OAL node writes the value 0 into those fields when it reconstructs the full OAL headers. The values will be correctly populated during reassembly after an OAL first fragment with an OCH-0 or uncompressed OAL header arrives.¶
Note: OAL header compression does not interfere with checksum calculation and verification, which must be applied according to the full OAL pseudo-header per Section 6.1 even when compression is used.¶
Note: when OAL-in-OAL encapsulation is used, any outer OCH-0/1 headers or full OAL headers with CRH-32 extensions include an MVFI, while the innermost OCH-0/1 header or full OAL header must not include an MFVI.¶
When an OAL source is unable to forward carrier packets directly to an OAL destination without "tunneling" through a pair of OAL intermediate nodes, the OAL source must regard the intermediate nodes as ingress and egress tunnel endpoints. This will result in nested OAL-in-OAL encapsulation in which the OAL source performs fragmentation on the inner OAL packet then forwards the fragments to the ingress tunnel endpoint which encapsulates each resulting OAL fragment in an additional OAL header/trailer before performing fragmentation following encapsulation.¶
For example, if the OAL source has an NCE for the OAL destination with MFVI 0x2376a7b5 and Identification 0x12345678 and the OAL ingress tunnel endpoint has an NCE for the OAL egress tunnel endpoint with MFVI 0xacdebf12 and Identification 0x98765432, the OAL source prepares the carrier packets using compressed/uncompressed OAL headers that include the MFVI and Identification corresponding to the OAL destination and with *NET header information addressed to the next hop toward the ingress tunnel endpoint. When the ingress tunnel endpoint receives the carrier packet, it recognizes the current MFVI included by the OAL source and determines the correct next hop MFVI.¶
The ingress tunnel endpoint then discards the *NET headers from the previous hop and encapsulates the original compressed/uncompressed OAL header within a second compressed/uncompressed OAL header/trailer while including the next-hop MVFI in the outer OAL encapsulation header and omitting the MFVI in the inner header. The ingress tunnel endpoint then includes *NET encapsulation headers with destinations appropriate for the next hop on the path to the egress tunnel endpoint. The encapsulation appears as shown in Figure 9:¶
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | *NET headers (previous hop) | | *NET headers (next hop) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Original OAL/OCH Hdr | | Encapsulation OAL/OCH Hdr | | Id=0x12345678 | | Id=0x98765432 | | MFVI=0x2376a7b5 | | MFVI=0xacdebf12 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Original OAL/OCH Hdr | | | | Id=0x12345678 | | Carrier packet data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Carrier packet data | | Original OAL Checksum | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | Original Carrier packet +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ from OAL source | Original OAL Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Encapsulation OAL Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Carrier packet following OAL ingress (re)encapsulation before fragmentation
Note that only a single OAL-in-OAL encapsulation layer is supported, and that MFVIs appear only in the outer OAL header (i.e., either within a CRH-32 routing header when a full OAL header is used or within an OCH-0/1 header). The inner OAL/OCH header should omit the CRH-32 header or set I to 0, respectively.¶
Note that OAL/OCH encapsulation may cause the payloads of OAL packets produced by the ingress tunnel endpoint to exceed the minimum MPS by a small amount. If the ingress has assurance that the path to the egress will include only links capable of transiting the resulting (slightly larger) carrier packets it should forward without further fragmentation. Otherwise, the ingress must perform fragmentation following encapsulation to produce two fragments such that the size of the first fragment matches the size of the original OAL packet, and with the remainder in a second fragment. The egress tunnel endpoint must then reassemble then decapsulate to arrive at the original OAL packet which is then subject to further forwarding.¶
The OAL encapsulates each original IP packet as an OAL packet then performs fragmentation to produce one or more carrier packets with the same 32-bit Identification value. In environments where spoofing is not considered a threat, OMNI interfaces send OAL packets with Identifications beginning with an unpredictable Initial Send Sequence (ISS) value [RFC7739] monotonically incremented (modulo 2**32) for each successive OAL packet sent to either a specific neighbor or to any neighbor. (The OMNI interface may later change to a new unpredictable ISS value as long as the Identifications are assured unique within a timeframe that would prevent the fragments of a first OAL packet from becoming associated with the reassembly of a second OAL packet.) In other environments, OMNI interfaces should maintain explicit per-neighbor send and receive windows to detect and exclude spurious carrier packets that might clutter the reassembly cache as discussed below.¶
OMNI interface neighbors use TCP-like synchronization to maintain windows with unpredictable ISS values incremented (modulo 2**32) for each successive OAL packet and re-negotiate windows often enough to maintain an unpredictable profile. OMNI interface neighbors exchange IPv6 ND messages with OMNI options that include TCP-like information fields to manage streams of OAL packets instead of streams of octets. As a link-layer service, the OAL provides low-persistence best-effort retransmission with no mitigations for duplication, reordering or deterministic delivery. Since the service model is best-effort and only control message sequence numbers are acknowledged, OAL nodes can select unpredictable new initial sequence numbers outside of the current window without delaying for the Maximum Segment Lifetime (MSL).¶
OMNI interface neighbors maintain current and previous window state in IPv6 ND neighbor cache entries (NCEs) to support dynamic rollover to a new window while still sending OAL packets and accepting carrier packets from the previous windows. Each NCE is indexed by the neighbor's LLA, which must also match the ULA used for OAL encapsulation. OMNI interface neighbors synchronize windows through asymmetric and/or symmetric IPv6 ND message exchanges. When a node receives an IPv6 ND message with new window information, it resets the previous window state based on the current window then resets the current window based on new and/or pending information.¶
The IPv6 ND message OMNI option header extension sub-option includes TCP-like information fields including Sequence Number, Acknowledgement Number, Window and flags (see: Section 12). OMNI interface neighbors maintain the following TCP-like state variables in the NCE:¶
Send Sequence Variables (current, previous and pending) SND.NXT - send next SND.WND - send window ISS - initial send sequence number Receive Sequence Variables (current and previous) RCV.NXT - receive next RCV.WND - receive window IRS - initial receive sequence number¶
OMNI interface neighbors "OAL A" and "OAL B" exchange IPv6 ND messages per [RFC4861] with OMNI options that include TCP-like information fields. When OAL A synchronizes with OAL B, it maintains both a current and previous SND.WND beginning with a new unpredictable ISS and monotonically increments SND.NXT for each successive OAL packet transmission. OAL A initiates synchronization by including the new ISS in the Sequence Number of an authentic IPv6 ND message with the SYN flag set and with Window set to M (up to 2**24) as a tentative receive window size while creating a NCE in the INCOMPLETE state if necessary. OAL A caches the new ISS as pending, uses the new ISS as the Identification for OAL encapsulation, then sends the resulting OAL packet to OAL B and waits up to RetransTimer milliseconds to receive an IPv6 ND message response with the ACK flag set (retransmitting up to MAX_UNICAST_SOLICIT times if necessary).¶
When OAL B receives the SYN, it creates a NCE in the STALE state if necessary, resets its RCV variables, caches the tentative (send) window size M, and selects a (receive) window size N (up to 2**24) to indicate the number of OAL packets it is willing to accept under the current RCV.WND. (The RCV.WND should be large enough to minimize control message overhead yet small enough to provide an effective filter for spurious carrier packets.) OAL B then prepares an IPv6 ND message with the ACK flag set, with the Acknowledgement Number set to OAL A's next sequence number, and with Window set to N. Since OAL B does not assert an ISS of its own, it uses the IRS it has cached for OAL A as the Identification for OAL encapsulation then sends the ACK to OAL A.¶
When OAL A receives the ACK, it notes that the Identification in the OAL header matches its pending ISS. OAL A then sets the NCE state to REACHABLE and resets its SND variables based on the Window size and Acknowledgement Number (which must include the sequence number following the pending ISS). OAL A can then begin sending OAL packets to OAL B with Identification values within the (new) current SND.WND for up to ReachableTime milliseconds or until the NCE is updated by a new IPv6 ND message exchange. This implies that OAL A must send a new SYN before sending more than N OAL packets within the current SND.WND, i.e., even if ReachableTime is not nearing expiration. After OAL B returns the ACK, it accepts carrier packets received from OAL A within either the current or previous RCV.WND as well as any new authentic NS/RS SYN messages received from OAL A even if outside the windows.¶
OMNI interface neighbors can employ asymmetric window synchronization as described above using two independent (SYN -> ACK) exchanges (i.e., a four-message exchange), or they can employ symmetric window synchronization using a modified version of the TCP three-way handshake as follows:¶
Following synchronization, OAL A and OAL B hold updated NCEs and can exchange OAL packets with Identifications set to SND.NXT while the state remains REACHABLE and there is available window capacity. Either neighbor may at any time send a new SYN to assert a new ISS. For example, if OAL A's current SND.WND for OAL B is nearing exhaustion and/or ReachableTime is nearing expiration, OAL A continues to send OAL packets under the current SND.WND while also sending a SYN with a new unpredictable ISS. When OAL B receives the SYN, it resets its RCV variables and may optionally return either an asymmetric ACK or a symmetric SYN/ACK to also assert a new ISS. While sending SYNs, both neighbors continue to send OAL packets with Identifications set to the current SND.NXT then reset the SND variables after an acknowledgement is received.¶
While the optimal symmetric exchange is efficient, anomalous conditions such as receipt of old duplicate SYNs can cause confusion for the algorithm as discussed in Section 3.4 of [RFC0793]. For this reason, the OMNI option header includes an RST flag which OAL nodes set in solicited NA responses to ACKs received with incorrect acknowledgement numbers. The RST procedures (and subsequent synchronization recovery) are conducted exactly as specified in [RFC0793].¶
OMNI interfaces may set the PNG ("ping") flag when a reachability confirmation outside the context of the IPv6 ND protocol is needed (OMNI interfaces therefore most often set the PNG flag in advertisement messages and ignore it in solicitation messages). When an OMNI interface receives a PNG, it returns an unsolicited NA (uNA) ACK with the PNG message Identification in the Acknowledgment, but without updating RCV state variables. OMNI interfaces return unicast uNA ACKs even for multicast PNG destination addresses, since OMNI link multicast is based on unicast emulation.¶
OMNI interfaces that employ the window synchronization procedures described above observe the following requirements:¶
Note: Although OMNI interfaces employ TCP-like window synchronization and support uNA ACK responses to SYNs and PNGs, all other aspects of the IPv6 ND protocol (e.g., control message exchanges, NCE state management, timers, retransmission limits, etc.) are honored exactly per [RFC4861].¶
Note: Recipients of OAL-encapsulated IPv6 ND messages index the NCE based on the ULA source address, which also determines the carrier packet Identification window. However, IPv6 ND messages may contain an LLA source address that does not match the ULA source address when the recipient acts as a proxy.¶
Note: OMNI interface neighbors apply the same send and receive windows for all of their (multilink) underlying interface pairs that exchange carrier packets. Each interface pair represents a distinct underlying network path, and the set of paths traversed may be highly diverse when multiple interface pairs are used. OMNI intermediate nodes therefore SHOULD NOT cache window synchronization parameters in IPv6 ND messages they forward since there is no way to ensure network-wide middlebox state consistency.¶
When the OAL source sends carrier packets to an OAL destination, it should cache recently sent packets in case timely best-effort selective retransmission is requested. The OAL destination in turn maintains a checklist for the (Source, Destination, Identification)-tuple of recently received carrier packets and notes the ordinal numbers of OAL packet fragments already received (i.e., as Frag #0, Frag #1, Frag #2, etc.). The timeframe for maintaining the OAL source and destination caches determines the link persistence (see: [RFC3366]).¶
If the OAL destination notices some fragments missing after most other fragments within the same link persistence timeframe have already arrived, it may issue an Automatic Repeat Request (ARQ) with Selective Repeat (SR) by sending a uNA message to the OAL source. The OAL destination creates a uNA message with an OMNI option with one or more Fragmentation Report (FRAGREP) sub-options that include a list of (Identification, Bitmap)-tuples for fragments received and missing from this OAL source (see: Section 12). The OAL destination includes an authentication signature if necessary, performs OAL encapsulation (with the its own address as the OAL source and the source address of the message that prompted the uNA as the OAL destination) and sends the message to the OAL source.¶
When the OAL source receives the uNA message, it authenticates the message then examines the FRAGREP. For each (Source, Destination, Identification)-tuple, the OAL source determines whether it still holds the corresponding carrier packets in its cache and retransmits any for which the Bitmap indicates a loss event. For example, if the Bitmap indicates that ordinal fragments #3, #7, #10 and #13 from the OAL packet with Identification 0x12345678 are missing the OAL source only retransmits carrier packets containing those fragments. When the OAL destination receives the retransmitted carrier packets, it admits the enclosed fragments into the reassembly cache and updates its checklist. If some fragments are still missing, the OAL destination may send a small number of additional uNA ARQ/SRs within the link persistence timeframe.¶
The OAL therefore provides a link-layer low persistence ARQ/SR service consistent with [RFC3366] and Section 8.1 of [RFC3819]. The service provides the benefit of timely best-effort link-layer retransmissions which may reduce packet loss and avoid some unnecessary end-to-end delays. This best-effort network-based service therefore compliments higher layer end-to-end protocols responsible for true reliability.¶
When the OMNI interface forwards original IP packets from the network layer, it invokes the OAL and returns internally-generated ICMPv4 Fragmentation Needed [RFC1191] or ICMPv6 Path MTU Discovery (PMTUD) Packet Too Big (PTB) [RFC8201] messages as necessary. This document refers to both of these ICMPv4/ICMPv6 message types simply as "PTBs", and introduces a distinction between PTB "hard" and "soft" errors as discussed below.¶
Ordinary PTB messages with ICMPv4 header "unused" field or ICMPv6 header Code field value 0 are hard errors that always indicate that a packet has been dropped due to a real MTU restriction. In particular, the OAL source drops the packet and returns a PTB hard error if the packet exceeds the OAL destination MRU. However, the OMNI interface can also forward large original IP packets via OAL encapsulation and fragmentation while at the same time returning PTB soft error messages (subject to rate limiting) if it deems the original IP packet too large according to factors such as link performance characteristics, reassembly congestion, etc. This ensures that the path MTU is adaptive and reflects the current path used for a given data flow. The OMNI interface can therefore continuously forward packets without loss while returning PTB soft error messages recommending a smaller size if necessary. Original sources that receive the soft errors in turn reduce the size of the packets they send (i.e., the same as for hard errors), but can soon resume sending larger packets if the soft errors subside.¶
An OAL source sends PTB soft error messages by setting the ICMPv4 header "unused" field or ICMPv6 header Code field to the value 1. The OAL source sets the PTB destination address to the original IP packet source, and sets the source address to one of its OMNI interface addresses that is routable from the perspective of the original source. The OAL source then sets the MTU field to a value smaller than the original packet size but no smaller than 576 for ICMPv4 or 1280 for ICMPv6, writes the leading portion of the original IP packet into the "packet in error" field, and returns the PTB soft error to the original source. When the original source receives the PTB soft error, it temporarily reduces the size of the packets it sends the same as for hard errors but may seek to increase future packet sizes dynamically while no further soft errors are arriving. (If the original source does not recognize the soft error code, it regards the PTB the same as a hard error but should heed the retransmission advice given in [RFC8201] suggesting retransmission based on normal packetization layer retransmission timers.)¶
An OAL destination may experience reassembly cache congestion, and can return uNA messages to the OAL source that originated the fragments (subject to rate limiting) to advertise reduced Reassembly Limits and/or to report individual reassembly failures. The OAL destination creates a uNA message with an OMNI option containing an authentication message sub-option if necessary followed optionally by a Reassembly Limit sub-option with a reduced value, and optionally including the leading portion an OAL first fragment containing the header of an original IP packet whose source must be notified (see: Section 12). The OAL destination encapsulates the leading portion of the OAL first fragment (beginning with the OAL header) in the "OAL First Fragment" field of sub-option, signs the message if an authentication sub-option is included, performs OAL encapsulation (with the its own address as the OAL source and the source address of the message that prompted the uNA as the OAL destination) and sends the message to the OAL source.¶
When the OAL source receives the uNA message, it records the new Reassembly Limit value for this OAL destination. If the Reassembly Limit sub-option includes an OAL First Fragment, the OAL source next sends a corresponding network layer PTB soft error to the original source to recommend a smaller size. The OAL source crafts the PTB by extracting the leading portion of the original IP packet from the OAL First Fragment field (i.e., not including the OAL header) and writes it in the "packet in error" field of a PTB with destination set to the original IP packet source and source set to one of its OMNI interface addresses that is routable from the perspective of the original source. For future transmissions, if the original IP packet is larger than the Reassembly Limit for this OAL destination the OAL source return a PTB soft error (subject to rate limiting) with Code set to 1 and MTU set to the reassembly limit while still forwarding the packet to the OMNI destination.¶
Original sources that receive PTB soft errors can dynamically tune the size of the original IP packets they to send to produce the best possible throughput and latency, with the understanding that these parameters may change over time due to factors such as congestion, mobility, network path changes, etc. The receipt or absence of soft errors should be seen as hints of when increasing or decreasing packet sizes may be beneficial. The OMNI interface supports continuous transmission and reception of packets of various sizes in the face of dynamically changing network conditions. Moreover, since PTB soft errors do not indicate a hard limit, original sources that receive soft errors can begin sending larger packets without waiting for the recommended 10 minutes specified for PTB hard errors [RFC1191][RFC8201]. The OMNI interface therefore provides an adaptive service that accommodates MTU diversity especially well-suited for dynamic multilink environments.¶
In light of the above, OAL sources, destinations and intermediate nodes observe the following normative requirements:¶
Note: Under the minimum MPS, ordinary 1500 octet original IP packets would require at most 4 OAL fragments, with each non-final fragment containing 400 payload octets and the final fragment containing 302 payload octets (i.e., the final 300 octets of the original IP packet plus the 2 octet trailer). For all packet sizes, the likelihood of successful reassembly may improve when the OMNI interface sends all fragments of the same fragmented OAL packet consecutively over the same underlying interface pair instead of spread across multiple underlying interface pairs. Finally, an assured minimum/path MPS allows continuous operation over all paths including those that traverse bridged L2 media with dissimilar MTUs.¶
Note: Certain legacy network hardware of the past millennium was unable to accept packet "bursts" resulting from an IP fragmentation event - even to the point that the hardware would reset itself when presented with a burst. This does not seem to be a common problem in the modern era, where fragmentation and reassembly can be readily demonstrated at line rate (e.g., using tools such as 'iperf3') even over fast links on ordinary hardware platforms. Even so, while the OAL destination is reporting reassembly congestion (see: Section 6.8) the OAL source could impose an inter-fragment delay and decrease the delay when reassembly congestion subsides.¶
As discussed in Section 3.7 of [RFC8900], there are four basic threats concerning IPv6 fragmentation; each of which is addressed by effective mitigations as follows:¶
IPv4 includes a 16-bit Identification (IP ID) field with only 65535 unique values such that at high data rates the field could wrap and apply to new carrier packets while the fragments of old packets using the same IP ID are still alive in the network [RFC4963]. Since carrier packets sent via an IPv4 path with DF=0 are normally no larger than 576 octets, IPv4 fragmentation is possible only at small-MTU links in the path which should support data rates low enough for safe reassembly [RFC3819]. (IPv4 carrier packets larger than 576 octets with DF=0 may incur high data rate reassembly errors in the path, but the OAL checksum provides OAL destination integrity assurance.) Since IPv6 provides a 32-bit Identification value, IP ID wraparound at high data rates is not a concern for IPv6 fragmentation.¶
Fragmentation security concerns for large IPv6 ND messages are documented in [RFC6980]. These concerns are addressed when the OMNI interface employs the OAL instead of directly fragmenting the IPv6 ND message itself. For this reason, OMNI interfaces MUST NOT send IPv6 ND messages larger than the OMNI interface MTU, and MUST employ OAL encapsulation and fragmentation for IPv6 ND messages larger than the minimum/path MPS for this OAL destination.¶
Unless the path is secured at the network-layer or below (i.e., in environments where spoofing is possible), OMNI interfaces MUST NOT send ordinary carrier packets with Identification values outside the current window and MUST secure IPv6 ND messages used for address resolution or window state synchronization. OAL destinations SHOULD therefore discard without reassembling any out-of-window OAL fragments received over an unsecured path.¶
By default, the OAL source includes a 40-octet IPv6 encapsulation header for each original IP packet during OAL encapsulation. The OAL source also calculates and appends a 2 octet trailing Checksum field then performs fragmentation such that a copy of the 40-octet IPv6 header plus an 8-octet IPv6 Fragment Header is included in each OAL fragment (when a Routing Header is added, the OAL encapsulation headers become larger still). However, these encapsulations may represent excessive overhead in some environments. OAL header compression can dramatically reduce the amount of encapsulation overhead, however a complimentary technique known as "packing" (see: [I-D.ietf-intarea-tunnels]) supports encapsulation of multiple original IP packets and/or control messages within a single OAL "super-packet".¶
When the OAL source has multiple original IP packets to send to the same OAL destination with total length no larger than the OAL destination MRU, it can concatenate them into a super-packet encapsulated in a single OAL header and trailing Checksum field. Within the OAL super-packet, the IP header of the first original IP packet (iHa) followed by its data (iDa) is concatenated immediately following the OAL header, then the IP header of the next original packet (iHb) followed by its data (iDb) is concatenated immediately following the first original packet, etc. with the trailing Checksum field included last. The OAL super-packet format is transposed from [I-D.ietf-intarea-tunnels] and shown in Figure 10:¶
<------- Original IP packets -------> +-----+-----+ | iHa | iDa | +-----+-----+ | | +-----+-----+ | | iHb | iDb | | +-----+-----+ | | | | +-----+-----+ | | | iHc | iDc | | | +-----+-----+ | | | v v v +----------+-----+-----+-----+-----+-----+-----+----+ | OAL Hdr | iHa | iDa | iHb | iDb | iHc | iDc |Csum| +----------+-----+-----+-----+-----+-----+-----+----+ <--- OAL "Super-Packet" with single OAL Hdr/Csum --->
When the OAL source prepares a super-packet, it applies OAL fragmentation and *NET encapsulation then sends the resulting carrier packets to the OAL destination. When the OAL destination receives the super-packet it reassembles if necessary, verifies the checksum, removes the trailing Checksum field, then regards the remaining OAL header Payload Length as the sum of the lengths of all payload packets. The OAL destination then selectively extracts each original IP packet (e.g., by setting pointers into the super-packet buffer and maintaining a reference count, by copying each packet into a separate buffer, etc.) and forwards each packet to the network layer. During extraction, the OAL determines the IP protocol version of each successive original IP packet 'j' by examining the four most-significant bits of iH(j), and determines the length of the packet by examining the rest of iH(j) according to the IP protocol version.¶
When an OAL source prepares a super-packet that includes an IPv6 ND message with an authentication signature or checksum as the first original IP packet (i.e., iHa/iDa), it calculates the authentication signature or checksum over the remainder of super-packet up to but not including the trailing OAL Checksum field. Security and integrity for forwarding initial protocol data packets in conjunction with IPv6 ND messages used to establish NCE state are therefore supported.¶
OAL sources may send NULL OAL packets known as "bubbles" for the purpose of establishing Network Address Translator (NAT) state on the path to the OAL destination. The OAL source prepares a bubble by crafting an OAL header with appropriate IPv6 source and destination ULAs, with the IPv6 Next Header field set to the value 59 ("No Next Header" - see [RFC8200]) and with only the trailing OAL Checksum field (i.e., and no protocol data) immediately following the IPv6 header.¶
The OAL source includes a random Identification value then encapsulates the OAL packet in *NET headers destined to either the mapped address of the OAL destination's first-hop ingress NAT or the INADDR of the OAL destination itself. When the OAL source sends the resulting carrier packet, any egress NATs in the path toward the *NET destination will establish state based on the activity but the bubble will be harmlessly discarded by either an ingress NAT on the path to the OAL destination or by the OAL destination itself.¶
The bubble concept for establishing NAT state originated in [RFC4380] and was later updated by [RFC6081]. OAL bubbles may be employed by mobility services such as [I-D.templin-6man-aero].¶
When the OMNI interface forwards original IP packets from the network layer it first invokes the OAL to create OAL packets/fragments if necessary, then includes any *NET encapsulations and finally engages the native frame format of the underlying interface. For example, for Ethernet-compatible interfaces the frame format is specified in [RFC2464], for aeronautical radio interfaces the frame format is specified in standards such as ICAO Doc 9776 (VDL Mode 2 Technical Manual), for various forms of tunnels the frame format is found in the appropriate tunneling specification, etc.¶
See Figure 2 for a map of the various *NET layering combinations possible. For any layering combination, the final layer (e.g., UDP, IP, Ethernet, etc.) must have an assigned number and frame format representation that is compatible with the selected underlying interface.¶
OMNI interfaces assign IPv6 Link-Local Addresses (LLAs) through pre-service administrative actions. Clients assign "MNP-LLAs" with interface identifiers that embed the Client's unique MNP, while Proxy/Servers assign "ADM-LLAs" that include an administrative ID guaranteed to be unique on the link. LLAs are configured as follows:¶
Since the prefix 0000::/8 is "Reserved by the IETF" [RFC4291], no MNPs can be allocated from that block ensuring that there is no possibility for overlap between the different MNP- and ADM-LLA constructs discussed above.¶
Since MNP-LLAs are based on the distribution of administratively assured unique MNPs, and since ADM-LLAs are guaranteed unique through administrative assignment, OMNI interfaces set the autoconfiguration variable DupAddrDetectTransmits to 0 [RFC4862].¶
Note: If future protocol extensions relax the 64-bit boundary in IPv6 addressing, the additional prefix bits of an MNP could be encoded in bits 16 through 63 of the MNP-LLA. (The most-significant 64 bits would therefore still be in bits 64-127, and the remaining bits would appear in bits 16 through 48.) However, the analysis provided in [RFC7421] suggests that the 64-bit boundary will remain in the IPv6 architecture for the foreseeable future.¶
Note: Even though this document honors the 64-bit boundary in IPv6 addressing, it specifies prefix lengths longer than /64 for routing purposes. This effectively extends IPv6 routing determination into the interface identifier portion of the IPv6 address, but it does not redefine the 64-bit boundary. Modern routing protocol implementations honor IPv6 prefixes of all lengths, up to and including /128.¶
OMNI domains use IPv6 Unique-Local Addresses (ULAs) as the source and destination addresses in OAL packet IPv6 encapsulation headers. ULAs are only routable within the scope of a an OMNI domain, and are derived from the IPv6 Unique Local Address prefix fc00::/7 followed by the L bit set to 1 (i.e., as fd00::/8) followed by a 40-bit pseudo-random Global ID to produce the prefix [ULA]::/48, which is then followed by a 16-bit Subnet ID then finally followed by a 64 bit Interface ID as specified in Section 3 of [RFC4193]. All nodes in the same OMNI domain configure the same 40-bit Global ID as the OMNI domain identifier. The statistic uniqueness of the 40-bit pseudo-random Global ID allows different OMNI domains to be joined together in the future without requiring renumbering.¶
Each OMNI link instance is identified by a 16-bit Subnet ID value between 0x0000 and 0xfeff in bits 48-63 of [ULA]::/48. The Subnet ID values 0xff00 through 0xfffe are reserved for future use, while 0xffff denotes the presence of a Temporary ULA (see below). For example, OMNI ULAs associated with instance 0 are configured from the prefix [ULA]:0000::/64, instance 1 from [ULA]:0001::/64, instance 2 from [ULA]:0002::/64, etc. ULAs and their associated prefix lengths are configured in correspondence with LLAs through stateless prefix translation where "MNP-ULAs" are assigned in correspondence to MNP-LLAs and "ADM-ULAs" are assigned in correspondence to ADM-LLAs. For example, for OMNI link instance [ULA]:1010::/64:¶
The ULA presents an IPv6 address format that is routable within the OMNI routing system and can be used to convey link-scoped IPv6 ND messages across multiple hops using IPv6 encapsulation [RFC2473]. The OMNI link extends across one or more underling Internetworks to include all Proxy/Servers. All Clients are also considered to be connected to the OMNI link, however unnecessary encapsulations are omitted whenever possible to conserve bandwidth (see: Section 14).¶
Temporary ULAs are constructed per [RFC8981] based on the prefix [ULA]:ffff::/64 and used by Clients when they have no other addresses. Temporary ULAs can be used for Client-to-Client communications outside the context of any supporting OMNI link infrastructure, and can also be used as an initial address while the Client is in the process of procuring an MNP. Temporary ULAs are not routable within the OMNI routing system, and are therefore useful only for OMNI link "edge" communications. Temporary ULAs employ optimistic DAD principles [RFC4429] since they are probabilistically unique.¶
Each OMNI link may be subdivided into SRT segments that often correspond to different administrative domains or physical partitions. OMNI nodes can use Segment Routing [RFC8402] to support efficient forwarding to destinations located in other OMNI link segments. A full discussion of Segment Routing over the OMNI link appears in [I-D.templin-6man-aero].¶
Note: IPv6 ULAs taken from the prefix fc00::/7 followed by the L bit set to 0 (i.e., as fc00::/8) are never used for OMNI OAL addressing, however the range could be used for MSP/MNP addressing under certain limiting conditions (see: Section 10).¶
OMNI domains use IP Global Unicast Address (GUA) prefixes [RFC4291] as Mobility Service Prefixes (MSPs) from which Mobile Network Prefixes (MNP) are delegated to Clients. Fixed correspondent node networks reachable from the OMNI domain are represented by non-MNP GUA prefixes that are not derived from the MSP, but are treated in all other ways the same as for MNPs.¶
For IPv6, GUA MSPs are assigned by IANA [IPV6-GUA] and/or an associated regional assigned numbers authority such that the OMNI domain can be interconnected to the global IPv6 Internet without causing inconsistencies in the routing system. An OMNI domain could instead use ULAs with the 'L' bit set to 0 (i.e., from the prefix fc00::/8)[RFC4193], however this would require IPv6 NAT if the domain were ever connected to the global IPv6 Internet.¶
For IPv4, GUA MSPs are assigned by IANA [IPV4-GUA] and/or an associated regional assigned numbers authority such that the OMNI domain can be interconnected to the global IPv4 Internet without causing routing inconsistencies. An OMNI domain could instead use private IPv4 prefixes (e.g., 10.0.0.0/8, etc.) [RFC3330], however this would require IPv4 NAT if the domain were ever connected to the global IPv4 Internet. OMNI interfaces advertise IPv4 MSPs into IPv6 routing systems as IPv4-mapped IPv6 prefixes [RFC4291] (e.g., the IPv6 prefix for the IPv4 MSP 192.0.2.0/24 is ::ffff:192.0.2.0/120).¶
OMNI interfaces assign the IPv4 anycast address TBD3, and IPv4 routers that configure OMNI interfaces advertise the prefix TBD3/N into the routing system of other networks (see: IANA Considerations). OMNI interfaces also configure global IPv6 anycast addresses formed according to [RFC3056] as:¶
2002:TBD3[32]:MNP[64]:Link_ID[16]¶
where TBD3[32] is the 32 bit IPv4 anycast address, MNP[64] encodes an MSP zero-padded to 64 bits (if necessary) and Link_ID[16] encodes a 16 bit value between 0 and 0xfffe that identifies a specific OMNI link within an OMNI domain (the Link_ID value 0xffff is an OMNI link "anycast" value configured by all OMNI interfaces within the same domain). For example, the OMNI IPv6 anycast address for MSP 2001:db8::/32 is 2002:TBD3[32]:2001:db8:0:0:Link_ID[16], the OMNI IPv6 anycast address for MSP 192.0.2.0/24 is 2002:TBD3[32]:0000:ffff:c000:0200:Link_ID[16], etc.).¶
OMNI interfaces assign OMNI IPv6 anycast addresses, and IPv6 routers that configure OMNI interfaces advertise the corresponding prefixes into the routing system of other networks. An OMNI IPv6 anycast prefix is formed the same as for any IPv6 prefix; for example, the prefix 2002:TBD3[32]:2001:db8::/80 matches all OMNI IPv6 anycast addresses covered by the prefix. By advertising OMNI IPv6 anycast prefixes in this way, OMNI Clients can locate and associate with the OMNI domain and/or a specific link within the OMNI domain that services the MSP of interest.¶
OMNI interfaces use OMNI IPv6 and IPv4 anycast addresses to support Service Discovery in the spirit of [RFC7094], i.e., the addresses are not intended for use in long-term transport protocol sessions. Specific applications for OMNI IPv6 and IPv4 anycast addresses are discussed throughout the document as well as in [I-D.templin-6man-aero].¶
OMNI Clients and Proxy/Servers that connect over open Internetworks include a unique node identification value for themselves in the OMNI options of their IPv6 ND messages (see: Section 12.2.12). An example identification value alternative is the Host Identity Tag (HIT) as specified in [RFC7401], while Hierarchical HITs (HHITs) [I-D.ietf-drip-rid] may be more appropriate for certain domains such as the Unmanned (Air) Traffic Management (UTM) service for Unmanned Air Systems (UAS). Another example is the Universally Unique IDentifier (UUID) [RFC4122] which can be self-generated by a node without supporting infrastructure with very low probability of collision.¶
When a Client is truly outside the context of any infrastructure, it may have no MNP information at all. In that case, the Client can use an IPv6 temporary ULA or (H)HIT as an IPv6 source/destination address for sustained communications in Vehicle-to-Vehicle (V2V) and (multihop) Vehicle-to-Infrastructure (V2I) scenarios. The Client can also propagate the ULA/(H)HIT into the multihop routing tables of (collective) Mobile/Vehicular Ad-hoc Networks (MANETs/VANETs) using only the vehicles themselves as communications relays.¶
When a Client connects via a protected-spectrum ANET, an alternate form of node identification (e.g., MAC address, serial number, airframe identification value, VIN, etc.) embedded in an LLA/ULA may be sufficient. The Client can then include OMNI "Node Identification" sub-options (see: Section 12.2.12) in IPv6 ND messages should the need to transmit identification information over the network arise.¶
OMNI interfaces maintain a neighbor cache for tracking per-neighbor state and use the link-local address format specified in Section 8. IPv6 Neighbor Discovery (ND) [RFC4861] messages sent over OMNI interfaces without encapsulation observe the native underlying interface Source/Target Link-Layer Address Option (S/TLLAO) format (e.g., for Ethernet the S/TLLAO is specified in [RFC2464]). IPv6 ND messages sent over OMNI interfaces using encapsulation do not include S/TLLAOs, but instead include a new option type that encodes encapsulation addresses, interface attributes and other OMNI link information. Hence, this document does not define an S/TLLAO format but instead defines a new option type termed the "OMNI option" designed for these purposes. (Note that OMNI interface IPv6 ND messages sent without encapsulation may include both OMNI options and S/TLLAOs, but the information conveyed in each is mutually exclusive.)¶
OMNI interfaces prepare IPv6 ND messages that include one or more OMNI options (and any other IPv6 ND options) then completely populate all option information. If the OMNI interface includes an authentication signature, it sets the IPv6 ND message Checksum field to 0 and calculates the authentication signature over the length of the entire OAL packet or super-packet (beginning with a pseudo-header of the IPv6 ND message IPv6 header up to but not including the trailing OAL Checksum field) but does not calculate/include the IPv6 ND message checksum itself. Otherwise, the OMNI interface calculates the standard IPv6 ND message checksum over the entire OAL packet or super-packet and writes the value in the Checksum field noting that optimized implementations can verify both the OAL and IPv6 ND message checksums in a single pass over the message data. OMNI interfaces verify authentication and/or integrity of each IPv6 ND message received according to the specific check(s) included, and process the message further only following verification.¶
OMNI interface Clients such as aircraft typically have multiple wireless data link types (e.g. satellite-based, cellular, terrestrial, air-to-air directional, etc.) with diverse performance, cost and availability properties. The OMNI interface would therefore appear to have multiple L2 connections, and may include information for multiple underlying interfaces in a single IPv6 ND message exchange. OMNI interfaces manage their dynamically-changing multilink profiles by including OMNI options in IPv6 ND messages as discussed in the following subsections.¶
OMNI options appear in IPv6 ND messages formatted as shown in Figure 11:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Sub-Options ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In this format:¶
The OMNI option is included in all OMNI interface IPv6 ND messages; the option is processed by receiving interfaces that recognize it and otherwise ignored. The OMNI interface processes all OMNI option instances received in the same IPv6 ND message in the consecutive order in which they appear. The OMNI option(s) included in each IPv6 ND message may include full or partial information for the neighbor. The OMNI interface therefore retains the union of the information in the most recently received OMNI options in the corresponding NCE.¶
Each OMNI option includes a Sub-Options block containing zero or more individual sub-options. Each consecutive sub-option is concatenated immediately following its predecessor. All sub-options except Pad1 (see below) are in an OMNI-specific type-length-value (TLV) format encoded as follows:¶
0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- | Sub-Type| Sub-Length | Sub-Option Data ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
Sub-Type is a 5-bit field that encodes the sub-option type. Sub-option types defined in this document are:¶
Sub-Option Name Sub-Type Pad1 0 PadN 1 Interface Attributes 2 Multilink Fwding Parameters 3 Traffic Selector 4 Geo Coordinates 5 DHCPv6 Message 6 HIP Message 7 PIM-SM Message 8 Reassembly Limit 9 Fragmentation Report 10 Node Identification 11 ICMPv6 Error 12 QUIC-TLS Message 13 Proxy/Server Departure 14 OMNI Header Extension 15 Sub-Type Extension 30
Sub-Types 16-29 are available for future assignment for major protocol functions. Sub-Type 31 is reserved by IANA.¶
The OMNI interface codes each sub-option with a 2 octet header that includes Sub-Type in the most significant 5 bits followed by Sub-Length in the next most significant 11 bits. Each sub-option encodes a maximum Sub-Length value of 2038 octets minus the lengths of the OMNI option header and any preceding sub-options. This allows ample Sub-Option Data space for coding large objects (e.g., ASCII strings, domain names, protocol messages, security codes, etc.), while a single OMNI option is limited to 2040 octets the same as for any IPv6 ND option.¶
The OMNI interface codes initial sub-options in a first OMNI option instance and subsequent sub-options in additional instances in the same IPv6 ND message in the intended order of processing. The OMNI interface can then code any remaining sub-options in additional IPv6 ND messages if necessary. Implementations must observe these size limits and refrain from sending IPv6 ND messages larger than the OMNI interface MTU.¶
The OMNI interface processes all OMNI option Sub-Options received in an IPv6 ND message while skipping over and ignoring any unrecognized sub-options. The OMNI interface processes the Sub-Options of all OMNI option instances in the consecutive order in which they appear in the IPv6 ND message, beginning with the first instance and continuing through any additional instances to the end of the message. If an individual sub-option length would cause processing to exceed the OMNI option instance and/or IPv6 ND message lengths, the OMNI interface accepts any sub-options already processed and ignores the remainder of that instance. The interface then processes any remaining OMNI option instances in the same fashion to the end of the IPv6 ND message.¶
When an OMNI interface includes an authentication sub-option (e.g., see: Section 12.2.8), it MUST appear as the first sub-option of the first OMNI option which must appear immediately following the IPv6 ND message header. If the IPv6 ND message includes additional authentication sub-options, only the first sub-option is processed and all others are ignored. If the IPv6 ND message is the first packet in a combined OAL super-packet, the OMNI interface calculates the authentication signature over the entire length of the super-packet, i.e., and not just to the end of the IPv6 ND message itself. (When no authentication sub-option is included, the OMNI interface instead calculates the IPv6 ND message checksum over the entire length of the packet/super-packet.)¶
When a Client OMNI interface prepares a secured unicast RS message, it includes an Interface Attributes sub-option specific to the underlying interface that will transmit the RS (see: Section 12.2.3) immediately following the authentication and header extension sub-options if present; otherwise as the first sub-option of the first OMNI option which must appear immediately following the IPv6 ND message header. When a Client OMNI interface prepares a secured unicast NS message, it instead includes a Multilink Forwarding Parameters sub-option specific to the underlying interface that will transmit the NS (see: Section 12.2.4).¶
Note: large objects that exceed the maximum Sub-Option Data length are not supported under the current specification; if this proves to be limiting in practice, future specifications may define support for fragmenting large sub-options across multiple OMNI options within the same IPv6 ND message (or even across multiple IPv6 ND messages, if necessary).¶
The following sub-option types and formats are defined in this document:¶
If more than one octet of padding is required, the PadN option, described next, should be used, rather than multiple Pad1 options.¶
0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- | S-Type=1| Sub-length=N | N padding octets ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
When a proxy forwards an IPv6 ND message with OMNI options, it can employ PadN to cancel any sub-options (other than Pad1) that should not be processed by the next hop by simply writing the value '1' over the Sub-Type. When the proxy alters the IPv6 ND message contents in this way, any included authentication and integrity checks are invalidated. See: Appendix B for a discussion of IPv6 ND message authentication and integrity.¶
The Interface Attributes sub-option provides neighbors with forwarding information for the multilink conceptual sending algorithm discussed in Section 14. Neighbors use the forwarding information to selecting among potentially multiple candidate underlying interfaces that can be used to forward carrier packets to the neighbor based on factors such as traffic selectors and link quality. Interface Attributes further include link-layer address information to be used for either direct INET encapsulation for targets in the local SRT segment or spanning tree forwarding for targets in remote SRT segments.¶
OMNI nodes include Interface Attributes for some/all of a target Client's underlying interfaces in NS/NA and uNA messages used to publish Client information (see: [I-D.templin-6man-aero]). At most one Interface Attributes sub-option for each distinct omIndex may be included; if an NS/NA message includes multiple Interface Attributes sub-options for the same omIndex, the first is processed and all others are ignored. OMNI nodes that receive NS/NA messages can use all of the included Interface Attributes and/or Traffic Selectors to formulate a map of the prospective target node as well as to seed the information to be populated in a Multilink Forwarding Parameters sub-option (see: Section 12.2.4).¶
OMNI Clients and Proxy/Servers also include Interface Attributes sub-options in RS/RA messages used to initialize, discover and populate routing and addressing information. Each RS message MUST contain exactly one Interface Attributes sub-option with an omIndex corresponding to the Client's underlying interface used to transmit the message, and each RA message MUST echo the same Interface Attributes sub-option with any (proxyed) information populated by the FHS Proxy/Server to provide operational context.¶
OMNI Client RS and Proxy/Server RA messages MUST include the Interface Attributes sub-option for the Client underlying interface in the first OMNI option immediately following an authentication message sub-option if present; otherwise, immediately following the OMNI header. When an FHS Proxy/Server receives an RS message destined to an anycast *NET address, it MUST include an Interface Attributes sub-option with omIndex '0' that encodes a unicast *NET INADDR immediately after the Interface Attributes sub-option for the Client's underlying interface in the solicited RA response. Any additional Interface Attributes sub-options that appear in RS/RA messages are ignored.¶
The Interface Attributes sub-options are formatted as shown below:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=2| Sub-length=N | omIndex | omType | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Provider ID | Link | Resvd | FMT | SRT | ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ LHS Proxy/Server MSID/INADDR ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Sub-Option Data contains an "Interface Attributes" option encoded as follows:¶
FMT - a 3-bit "Forward/Mode/Type" code interpreted as follows:¶
OMNI nodes include the Multilink Forwarding Parameters sub-option in NS/NA messages used to coordinate with multilink route optimization targets. If an NS message includes the sub-option, the solicited NA response must also include the sub-option. The OMNI node MUST include the sub-option in the first OMNI option immediately following an authentication message sub-option. Otherwise, the OMNI node MUST include the sub-option immediately following the OMNI header. Each NS/NA message may contain at most one Multilink Forwarding Parameters sub-option; if an NS/NA message contains additional Multlink Forwarding Parameters sub-options, the first is processed and all others are ignored.¶
When an NS/NA message includes the sub-option, the FHS Client omIndex MUST correspond to the underlying interface used to transmit the message. When the NS/NA message also includes Interface Attributes sub-options any that include the same FHS/LHS Client omIndex are ignored while all others are processed.¶
The Multilink Forwarding Parameters sub-option includes the necessary state for establishing Multilink Forwarding Vectors (MFVs) in the Multilink Forwarding Information Bases (MFIBs) of the OAL source, destination and intermediate nodes in the path. The sub-option also records addressing information for FHS/LHS nodes on the path, including "INADDRs" which MUST be unicast IP encapsulation addresses (i.e., and not anycast/multicast). The manner for populating multilink forwarding information is specified in detail in [I-D.templin-6man-aero].¶
The Multilink Forwarding Parameters sub-option is formatted as shown in Figure 17:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=3| Sub-length=N |Job| A | B | ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ Multilink Forwarding Vector Index (MFVI) List ~ ~ (5 consecutive 4-octet MFVIs) ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ Tunnel Window Synchronization Parameters ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |FHS Cli omIndex| omType | Provider ID | Link | Resvd | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | FMT | SRT | ~ +-+-+-+-+-+-+-+-+ ~ ~ FHS Proxy/Server MSID/INADDR ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ FHS Bridge MSID/INADDR ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |LHS Cli omIndex| omType | Provider ID | Link | Resvd | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | FMT | SRT | ~ +-+-+-+-+-+-+-+-+ ~ ~ LHS Proxy/Server MSID/INADDR ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ LHS Bridge MSID/INADDR ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Sub-Option Data contains Multilink Forwarding Parameters as follows:¶
Job/A/B is a 1-octet field that determines per-hop processing of the MFVI List, where A is a 3-bit count of the number of "A" MVFI List entries and B is a 3-bit count of the number of "B" MVFI List entries (valid A/B values are 0-5). Job is a 2-bit code interpreted as follows:¶
Job/A/B together determine the per-hop behavior at each FHS/LHS source, intermediate node and destination that processes an IPv6 ND message. When a Job code specifies "Initialize", each FHS/LHS node that processes the message creates a new MVF. When a Job code specifies "Build", each node that processes the message assigns a new MFVI. When a Job code specifies "Follow", each node that processes the message uses an A/B MFVI List entry to locate an MFV (if the MFV cannot be located, the node returns a parameter problem and drops the message). Using this algorithm, FHS sources that send code "00" solicitations and receive code "01 advertisements discover only "A" information, while LHS sources that receive code "00" solicitations and return code "01" advertisements discover only "B" information. FHS/LHS intermediate nodes can instead examine A, B and the MFVI List to determine the number of previous hops, the number of remaining hops, and the A/B MFVIs associated with the previous/remaining hops. However, no intermediate nodes will discover inappropriate A/B MFVIs for their location in the multihop forwarding chain. See: [I-D.templin-6man-aero] for further discussion on A/B MFVI processing.¶
For Job codes "00" and "01" only, two trailing state variable blocks are included for First-Hop Segment (FHS) followed by Last-Hop Segment (LHS) network elements. When present, each block encodes the following information:¶
When used in conjunction with Interface Attributes and/or Multilink Forwarding Parameters information, the Traffic Selector sub-option provides forwarding information for the multilink conceptual sending algorithm discussed in Section 14.¶
IPv6 ND messages include Traffic Selectors for some or all of the source/target Client's underlying interfaces. Traffic Selectors for some or all of a target Client's underlying interfaces are also included in uNA messages used to publish Client information changes. See: [I-D.templin-6man-aero] for more information.¶
Traffic Selectors must be honored by all implementations in the format shown below:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=4| Sub-length=N | omIndex | TS Format | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ ~ RFC 6088 Format Traffic Selector ~ ~ ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Sub-Option Data contains a "Traffic Selector" encoded as follows:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=5| Sub-length=N | Geo Type |Geo Coordinates +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ...
Geo Type is a 1 octet field that encodes a type designator that determines the format and contents of the Geo Coordinates field that follows. The following types are currently defined:¶
The Dynamic Host Configuration Protocol for IPv6 (DHCPv6) sub-option may be included in the OMNI options of Client RS messages and Proxy/Server RA messages. FHS Proxy/Servers that forward RS/RA messages between a Client and an LHS Proxy/Server also forward DHCPv6 Sub-Options unchanged. Note that DHCPv6 messages do not include a Checksum field since integrity is protected by the IPv6 ND message checksum, authentication signature and/or lower-layer authentication and integrity checks.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=6| Sub-length=N | msg-type | id (octet 0) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | transaction-id (octets 1-2) | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | . DHCPv6 options . . (variable number and length) . | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Host Identity Protocol (HIP) Message sub-option (when present) provides authentication for IPv6 ND messages exchanged between Clients and FHS Proxy/Servers over an open Internetwork. FHS Proxy/Servers authenticate the HIP authentication signatures in source Client IPv6 ND messages before securely forwarding them to other OMNI nodes. LHS Proxy/Servers that receive secured IPv6 ND messages from other OMNI nodes that do not already include a security sub-option insert HIP authentication signatures before forwarding them to the target Client.¶
OMNI interfaces MUST include the HIP message (when present) as the first sub-option of the first OMNI option, which MUST appear immediately following the IPv6 ND message header. OMNI interfaces can therefore easily locate the HIP message and verify the authentication signature without applying deep inspection. OMNI interfaces that receive IPv6 ND messages without a HIP (or other authentication) sub-option instead verify the IPv6 ND message checksum.¶
OMNI interfaces include the HIP message sub-option when they forward IPv6 ND messages that require security over INET underlying interfaces, i.e., where authentication and integrity is not already assured by lower layers. The OMNI interface calculates the authentication signature over the entire length of the OAL packet (or super-packet) beginning with a pseudo-header of the IPv6 ND message header and extending over the remainder of the OAL packet up to but not including the trailing OAL Checksum field. OMNI interfaces that process OAL packets that contain secured IPv6 ND messages verify the signature then either process the rest of the message locally or forward a proxyed copy to the next hop.¶
When a FHS Client inserts a HIP message sub-option in an NS/NA message destined to a target in a remote spanning tree segment, it must ensure that the insertion does not cause the message to exceed the OMNI interface MTU. When the remote segment LHS Proxy/Server forwards the NS/NA message from the spanning tree to the target Client, it inserts a new HIP message sub-option if necessary while overwriting or cancelling the (now defunct) HIP message sub-option supplied by the FHS Client.¶
If the defunct HIP sub-option size was smaller than the space needed for the LHS Client HIP message (or, if no defunct HIP sub-option is present), the LHS Proxy/Server adjusts the space immediately following the OMNI header by copying the preceding portion of the IPv6 ND message into buffer headroom free space or copying the remainder of the IPv6 ND message into buffer tailroom free space. The LHS Proxy/Server then insets the new HIP sub-option immediately after the OMNI header and immediately before the next sub-option while properly overwriting the defunct sub-option if present.¶
If the defunct HIP sub-option size was larger than the space needed for the LHS Client HIP message, the LHS Proxy/Server instead overwrites the existing sub-option and writes a single Pad1 or PadN sub-option over the next 1-2 octets to cancel the remainder of the defunct sub-option. If the LHS Proxy/Server cannot create sufficient space through any means without causing the OMNI option to exceed 2040 octets or causing the IPv6 ND message to exceed the OMNI interface MTU, it returns a suitable error (see: Section 12.2.13) and drops the message.¶
The HIP message sub-option is formatted as shown below:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=7| Sub-length=N |0| Packet Type |Version| RES.|1| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Controls | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sender's Host Identity Tag (HIT) | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Receiver's Host Identity Tag (HIT) | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | / HIP Parameters / / / | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Note: In some environments, maintenance of a Host Identity Tag (HIT) namespace may be unnecessary for securely associating an OMNI node with an IPv6 address-based identity. In that case, other types of IPv6 addresses (e.g., a Client's MNP-LLA, a Proxy/Server's ADM-LLA, etc.) can be used instead of HITs in the authentication signature as long as the address can be uniquely associated with the Sender/Receiver.¶
The Protocol Independent Multicast - Sparse Mode (PIM-SM) Message sub-option may be included in the OMNI options of IPv6 ND messages. PIM-SM messages are formatted as specified in Section 4.9 of [RFC7761], with the exception that the Checksum field is replaced by a Reserved field (set to 0) since the IPv6 ND message is already protected by the IPv6 ND message checksum, authentication signature and/or lower-layer authentication and integrity checks. The PIM-SM message sub-option format is shown in Figure 22:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=8| Sub-length=N |PIM Ver| Type | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | / PIM-SM Message / / / | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Reassembly Limit sub-option may be included in the OMNI options of IPv6 ND messages. The message consists of a 16-bit Reassembly Limit value optionally followed by an (N-2)-octet leading portion of an OAL First Fragment that triggered the message.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | S-Type=9| Sub-length=N | Reassembly Limit | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | OAL First Fragment (As much of invoking packet | + as possible without causing the IPv6 ND message + | to exceed the minimum IPv6 MTU) | + +
Fragmentation Report (FRAGREP) sub-options may be included in the OMNI options of uNA messages sent from an OAL destination to an OAL source. The message consists of (N / 8)-many (Identification, Bitmap)-tuples which include the Identification values of OAL fragments received plus a Bitmap marking the ordinal positions of individual fragments received and fragments missing.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=10| Sub-Length = N | Identification #1 (bits 0 -15)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification #1 (bits 15-31)| Bitmap #1 (bits 0 - 15) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bitmap #1 (bits 16-47) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bitmap #1 (bits 48 - 63) | Identification #2 (bits 0 -15)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification #2 (bits 15-31)| Bitmap #2 (bits 0 - 15) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bitmap #2 (bits 16-47) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bitmap #2 (bits 48 - 63) | Identification #3 (bits 0 -15)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification #3 (bits 15-31)| Bitmap #3 (bits 0 - 15) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bitmap #3 (bits 16-47) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bitmap #3 (bits 48 - 63) | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... + | ... | + ... +
Bitmap (i) includes an ordinal checklist of fragments, with each bit set to 1 for a fragment received or 0 for a fragment missing. (Up to 64 ordinal numbered fragments for each packet may be recoded.) For example, for a 20-fragment OAL packet with ordinal fragments #3, #10, #13 and #17 missing and all other fragments received, Bitmap (i) encodes the following:¶
0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- |1|1|1|0|1|1|1|1|1|1|0|1|1|0|1|1|1|0|1|1|0|0|0|... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
(Note that loss of an OAL atomic fragment is indicated by a Bitmap(i) with all bits set to 0.)¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=11| Sub-length=N | ID-Type | ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ Node Identification Value (N-1 octets) ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ID-Type is a 1 octet field that encodes the type of the Node Identification Value. The following ID-Type values are currently defined:¶
OMNI interfaces code Node Identification Values used for DHCPv6 messaging purposes as a DHCP Unique IDentifier (DUID) using the "DUID-EN for OMNI" format with enterprise number 45282 (see: Section 25) as shown in Figure 27:¶
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | DUID-Type (2) | EN (high bits == 0) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | EN (low bits = 45282) | ID-Type | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | . Node Identification Value . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In this format, the OMNI interface codes the ID-Type and Node Identification Value fields from the OMNI sub-option following a 6 octet DUID-EN header, then includes the entire "DUID-EN for OMNI" in a DHCPv6 message per [RFC8415].¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=12| Sub-length=N | ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- ~ ~ RFC4443 Error Message Body ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=13| Sub-length=N | ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- ~ ~ QUIC-TLS Message ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
When present, the QUIC-TLS Message sub-option MUST appear immediately after the header of the first OMNI option in the IPv6 ND message; if the sub-option appears in any other location it MUST be ignored. IPv6 ND solicitation and advertisement messages serve as couriers to transport the QUIC and TLS parameters necessary to establish a secured QUIC connection.¶
OMNI Clients include a Proxy/Server Departure sub-option in RS messages when they associate with a new FHS and/or Hub Proxy/Server and need to send a departure indication to an old FHS and/or Hub Proxy/Server. The Proxy/Server Departure sub-option is formatted as shown below:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=14| Sub-length=8 |Old FHS Proxy/Server MSID (0-1)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Old FHS Proxy/Server MSID (2-3)|Old Hub Proxy/Server MSID (0-1)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Old Hub Proxy/Server MSID (2-3)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
IPv6 ND messages used for Prefix Length assertion, service coordination and/or Window Synchronization include an OMNI Header Extension sub-option. If an OMNI Header Extension sub-option is included, it must appear immediately after the authentication sub-option if present; otherwise, as the first (non-padding) sub-option of the first OMNI option. If multiple OMNI Header Extension sub-options are included (whether in a single OMNI option or multiple), only the first is processed and all others are ignored.¶
The OMNI Header Extension sub-option is formatted as follows:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=15| Sub-length=14 | Preflen |N|A|U| Reservd | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Acknowledgment Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S|A|R|O|P| | | |Y|C|S|P|N| Res | Window | |N|K|T|T|G| | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The first two octets of Sub-Option Data contains a 1-octet Prefix Length followed by a 1-octet flags field interpreted as follows:¶
Since the Sub-Type field is only 5 bits in length, future specifications of major protocol functions may exhaust the remaining Sub-Type values available for assignment. This document therefore defines Sub-Type 30 as an "extension", meaning that the actual Sub-Option type is determined by examining a 1 octet "Extension-Type" field immediately following the Sub-Length field. The Sub-Type Extension is formatted as shown in Figure 32:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=30| Sub-length=N | Extension-Type| ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ ~ ~ Extension-Type Body ~ ~ ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Extension-Type values 0 and 1 are defined in the following subsections, while Extension-Type values 2 through 252 are available for assignment by future specifications which must also define the format of the Extension-Type Body and its processing rules. Extension-Type values 253 and 254 are reserved for experimentation, as recommended in [RFC3692], and value 255 is reserved by IANA.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=30| Sub-length=N | Ext-Type=0 | Header Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ Header Option Value ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Header Type and Header Option Value are coded exactly as specified in Section 5.1.1 of [RFC4380]; the following types are currently defined:¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |S-Type=30| Sub-length=N | Ext-Type=1 | Trailer Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ Trailer Option Value ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Trailer Type and Trailer Option Value are coded exactly as specified in Section 4 of [RFC6081]; the following Trailer Types are currently defined:¶
The multicast address mapping of the native underlying interface applies. The Client mobile router also serves as an IGMP/MLD Proxy for its EUNs and/or hosted applications per [RFC4605].¶
The Client uses Multicast Listener Discovery (MLDv2) [RFC3810] to coordinate with Proxy/Servers, and *NET L2 elements use MLD snooping [RFC4541]. The Client can also employ multicast routing protocols to coordinate with network-based multicast sources as specified in [I-D.templin-6man-aero].¶
Since the OMNI link model is NBMA, OMNI links support link-scoped multicast through iterative unicast transmissions to individual multicast group members (i.e., unicast/multicast emulation).¶
The Client's IPv6 layer selects the outbound OMNI interface according to SBM considerations when forwarding original IP packets from local or EUN applications to external correspondents. Each OMNI interface maintains a neighbor cache the same as for any IPv6 interface, but includes additional state for multilink coordination. Each Client OMNI interface maintains default routes via Proxy/Servers discovered as discussed in Section 15, and may configure more-specific routes discovered through means outside the scope of this specification.¶
For each original IP packet it forwards, the OMNI interface selects one or more source underlying interfaces based on PBM factors (e.g., traffic attributes, cost, performance, message size, etc.) and one or more target underlying interfaces for the neighbor based on Interface Attributes received in IPv6 ND messages (see: Section 12.2.3). Multilink forwarding may also direct packet replication across multiple underlying interface pairs for increased reliability at the expense of duplication. The set of all Interface Attributes and Traffic Selectors received in IPv6 ND messages determines the multilink forwarding profile for selecting target underlying interfaces.¶
When the OMNI interface sends an original IP packet over a selected source underlying interface, it first employs OAL encapsulation and fragmentation as discussed in Section 5, then performs *NET encapsulation as directed by the appropriate MFV. The OMNI interface also performs *NET encapsulation (following OAL encapsulation) when the nearest Proxy/Server is located multiple hops away as discussed in Section 15.2.¶
OMNI interface multilink service designers MUST observe the BCP guidance in Section 15 [RFC3819] in terms of implications for reordering when original IP packets from the same flow may be spread across multiple underlying interfaces having diverse properties.¶
Clients may connect to multiple independent OMNI links within the same or different OMNI domains to support SBM. The Client configures a separate OMNI interface for each link so that multiple interfaces (e.g., omni0, omni1, omni2, etc.) are exposed to the IP layer. Each OMNI interface configures one or more OMNI anycast addresses (see: Section 10), and the Client injects the corresponding anycast prefixes into the EUN routing system. Multiple distinct OMNI links can therefore be used to support fault tolerance, load balancing, reliability, etc.¶
Applications in EUNs can use Segment Routing to select the desired OMNI interface based on SBM considerations. The application writes an OMNI anycast address into the original IP packet's destination address, and writes the actual destination (along with any additional intermediate hops) into the Segment Routing Header. Standard IP routing directs the packet to the Client's mobile router entity, where the anycast address identifies the correct OMNI interface for next hop forwarding. When the Client receives the packet, it replaces the IP destination address with the next hop found in the Segment Routing Header and forwards the message via the OMNI interface identified by the anycast address.¶
After a Proxy/Server has registered an MNP for a Client (see: Section 15), the Proxy/Server will forward all packets destined to an address within the MNP to the Client. The Client will under normal circumstances then forward the packet to the correct destination within its internal networks.¶
If at some later time the Client loses state (e.g., after a reboot), it may begin returning packets with destinations corresponding to its MNP to the Proxy/Server as its default router. The Proxy/Server therefore drops any original IP packets received from the Client with a destination address that corresponds to the Client's MNP (i.e., whether LLA, ULA or GUA), and drops any carrier packets with both source and destination address corresponding to the same Client's MNP regardless of their origin.¶
Clients engage the MS by sending RS messages with OMNI options under the assumption that one or more Proxy/Server will process the message and respond. The RS message is received by a FHS Proxy/Server, which may in turn forward a proxyed copy of the RS to a Hub Proxy/Server located on the same or different SRT segment. The Hub Proxy/Server then returns an RA message either directly to the Client or via an FHS Proxy/Server acting as a proxy.¶
Clients and FHS Proxy/Servers include an authentication signature in their RS/RA exchanges when necessary; otherwise, they calculate and include a valid IPv6 ND message checksum (see: Section 12 and Appendix B). FHS and Hub Proxy/Server RS/RA message exchanges over the SRT secured spanning tree instead always include the checksum and omit the authentication signature. Clients and Proxy/Servers use the information included in RS/RA messages to establish NCE state and OMNI link autoconfiguration information as discussed in this section.¶
For each underlying interface, the Client sends RS messages with OMNI options to coordinate with a (potentially different) FHS Proxy/Server for each interface and a single Hub Proxy/Server. All Proxy/Servers are identified by their MSIDs and accept carrier packets addressed to their anycast/unicast *NET INADDRs; the Hub Proxy/Server may be chosen among any of the Client's FHS Proxy/Servers or may be any other Proxy/Server for the OMNI link. Example MSID/INADDR discovery methods are given in [RFC5214] and include data link login parameters, name service lookups, static configuration, a static "hosts" file, etc. In the absence of other information, the Client can resolve the DNS Fully-Qualified Domain Name (FQDN) "linkupnetworks.[domainname]" where "linkupnetworks" is a constant text string and "[domainname]" is a DNS suffix for the OMNI link (e.g., "example.com").¶
Clients configure OMNI interfaces that observe the properties discussed in previous sections. The OMNI interface and its underlying interfaces are said to be in either the "UP" or "DOWN" state according to administrative actions in conjunction with the interface connectivity status. An OMNI interface transitions to UP or DOWN through administrative action and/or through state transitions of the underlying interfaces. When a first underlying interface transitions to UP, the OMNI interface also transitions to UP. When all underlying interfaces transition to DOWN, the OMNI interface also transitions to DOWN.¶
When a Client OMNI interface transitions to UP, it sends RS messages to register its MNP and an initial set of underlying interfaces that are also UP. The Client sends additional RS messages to refresh lifetimes and to register/deregister underlying interfaces as they transition to UP or DOWN. The Client's OMNI interface sends initial RS messages over an UP underlying interface with its MNP-LLA as the source (or with the unspecified address (::) as the source if it does not yet have an MNP-LLA) and with destination set to link-scoped All-Routers multicast or the ADM-LLA of a specific Proxy/Server. The OMNI interface includes an OMNI option per Section 12 with an OMNI header extension with Preflen assertion, N/A/U flags, an Interface Attributes sub-option for the underlying interface and with any other necessary OMNI sub-options such as authentication, Proxy/Server Departure, Reassembly Limits, etc.¶
The Client then calculates the authentication signature or checksum and prepares to forward the RS over the underlying interface using OAL encapsulation and fragmentation if necessary. If the Client uses OAL encapsulation for RS messages sent to an unsynchronized FHS Proxy/Server over an INET interface, the entire RS message must fit within a single carrier packet (i.e., an atomic fragment) so that the FHS Proxy/Server can verify the authentication signature without having to reassemble. The OMNI interface selects an Identification value (see: Section 6.6), sets the OAL source address to the ULA corresponding to the RS source (or a Temporary ULA or (H)HIT if the RS source is the unspecified address (::)), sets the OAL destination to an OMNI IPv6 anycast or ADM-ULA unicast address then performs fragmentation if necessary. When *NET encapsulation is used, the Client includes the discovered FHS Proxy/Server INADDR or an anycast address as the *NET destination then forwards the resulting carrier packet(s) into the *NET.¶
When an FHS Proxy/Server receives the carrier packets containing an RS it sets aside the *NET headers, verifies the Identifications and reassembles if necessary, sets aside the OAL header, then verifies the RS authentication signature or checksum. The FHS Proxy/Server then caches the OMNI Window Synchronization parameters, Interface Attributes and any Traffic Selector sub-options in a NCE for the Client while also caching the *NET (UDP/IP) and OAL (ULA) source and destination address information. The FHS Proxy/Server next caches the OMNI option N flag to determine its role in processing NS(NUD) messages (see: Section 12.1) then examines the RS destination address. If the destination matches its own ADM-LLA, the FHS Proxy/Server assumes the Hub role and acts as the sole entry point for injecting the Client's MNP into the MS routing system (i.e., after performing any necessary MNP prefix delegation operations) according to the RS source address and OMNI option Prefix Length. The FHS/Hub Proxy/Server then caches the OMNI option A/U flags to determine its role in processing NS(AR) messages and generating uNA messages (see: Section 12.1).¶
The FHS/Hub Proxy/Server then prepares to return an RA message directly to the Client by first populating the Cur Hop Limit, Flags, Router Lifetime, Reachable Time and Retrans Timer fields with values appropriate for the OMNI link. The FHS/Hub Proxy/Server next includes as the first RA message option an OMNI option with Window Synchronization information, an authentication sub-option if necessary and a (proxyed) copy of the Client's original Interface Attributes sub-option with its INET-facing interface information written in the FMT/SRT and LHS Proxy/Server MSID/INADDR fields. If the RS *NET destination IP address was anycast, the FHS/Hub Proxy/Server next includes a second Interface Attributes sub-option with omIndex set to '0' and with a unicast *NET IP address for its Client-facing interface in the INADDR field.¶
The FHS/Hub Proxy/Server next includes an Origin Indication sub-option that includes the RS *NET source INADDR information (see: Section 12.2.17.1), then includes any other necessary OMNI sub-options (either within the same OMNI option or in additional OMNI options). Following the OMNI option(s), the FHS/Hub Proxy/Server next includes any other necessary RA options such as PIOs with (A; L=0) that include the OMNI link MSPs [RFC8028], RIOs [RFC4191] with more-specific routes, Nonce and Timestamp options, etc. The FHS/Hub Proxy/Server then sets the RA source address to its own ADM-LLA and destination address to the Client's MNP-LLA, then calculates the authentication signature or checksum. The FHS/Hub Proxy/Server finally performs OAL encapsulation with source set to its own ADM-ULA and destination set to the OAL source that appeared in the RS, then fragments if necessary, encapsulates each fragment in appropriate *NET headers with source and destination address information reversed from the RS *NET information and returns the resulting carrier packets to the Client over the same underlying interface the RS arrived on.¶
When an FHS Proxy/Server receives an RS with a valid authentication signature or checksum and with destination set to link-scoped All-Routers multicast, it can either assume the Hub role the same as above or act as a proxy and select the ADM-LLA of another Proxy/Server to serve as the Hub. When an FHS Proxy/Server assumes the proxy role or receives an RS with destination set to the ADM-LLA of another Proxy/Server, it proxys the message. The FHS Proxy/Server caches the Client's Window Synchronization, N flag, Interface Attributes and *NET/OAL address information as above then writes its own INET-facing FMT/SRT and LHS Proxy/Server MSID/INADDR information into the appropriate Interface Attributes sub-option fields. The FHS Proxy/Server then calculates and includes the checksum, performs OAL encapsulation with source set to its own ADM-ULA and destination set to the ADM-ULA of the Hub Proxy/Server, fragments if necessary, encapsulates each fragment in appropriate *NET headers and sends the resulting carrier packets into the SRT secured spanning tree.¶
When the Hub Proxy/Server receives the carrier packets, it discards the *NET headers, reassembles if necessary to obtain the proxyed RS (i.e., one with an ADM-ULA source address) then caches any state (including the A/U flags, OAL addresses, Interface Attributes information and Traffic Selectors) in a NCE for the Client and performs any necessary prefix delegation and routing protocol injection. The Hub Proxy/Server then returns an RA that echoes the Client's (proxyed) Interface Attributes sub-option and with any RA parameters the same as specified above. The Hub Proxy/Server then sets the RA source address to its own ADM-LLA and destination address to the Client's MNP-LLA, calculates the checksum then encapsulates the RA as an OAL packet with source set to its own ADM-ULA and destination set to the ADM-ULA of the FHS Proxy/Server that sent the RS. The Hub Proxy/Server finally fragments if necessary, encapsulates each fragment in appropriate *NET headers and sends the resulting carrier packets into the secured spanning tree.¶
When the FHS Proxy/Server receives the carrier packets it discards the *NET headers, reassembles to obtain the RA message, verifies the checksum then updates the OMNI interface NCEs for both the Hub and Client. The FHS Proxy/Server then proxies the RA by changing the OAL source to its own ADM-ULA and the OAL destination to the MNP-ULA or temporary ULA of the Client, then sets the P flag in the RA flags field [RFC4389]. The FHS Proxy/Server next includes Window Synchronization parameters responsive to those in the Client's RS, an Interface Attributes sub-option with omIndex '0' and with its unicast *NET IP address if necessary (see above), an Origin Indication sub-option with the Client's cached INADDR and an authentication sub-option if necessary. The FHS Proxy/Server finally selects an Identification value per Section 6.6, calculates the authentication signature or checksum, fragments if necessary, encapsulates each fragment in *NET headers with addresses taken from the Client's NCE and returns the resulting carrier packets via the same underlying interface over which the RS was received.¶
When the Client receives the carrier packets, it discards the *NET headers, reassembles and removes the OAL header/trailer to obtain the RA message, verifies the authentication signature or checksum, then updates the OMNI interface NCEs for both the Hub and FHS Proxy/Server. If the Client has multiple underlying interfaces, it creates additional FHS Proxy/Server NCEs as necessary when it receives RAs over those interfaces (noting that multiple of the Client's underlying interfaces may be serviced by the same FHS Proxy/Server). For each underlying interface, the Client caches the (filled-out) Interface Attributes for its own omIndex and Origin Indication information that it received in an RA message over that interface so that it can include them in future NS/NA messages to provide neighbors with accurate FMT/SRT/LHS information. (If the message includes an Interface Attributes sub-option with omIndex '0', the Client also caches the INADDR as the *NET-local unicast address of the FHS Proxy//Server via that underlying interface.) The Client then compares the Origin Indication INADDR information with its own underlying interface addresses to determine whether there may be NATs on the path to the FHS Proxy/Server; if the INADDR information differs, the Client is behind a NAT and must supply the Origin information in IPv6 ND message exchanges with prospective neighbors on the same SRT segment. The Client finally configures default routes and assigns the OMNI Subnet Router Anycast address corresponding to the MNP (e.g., 2001:db8:1:2::) to the OMNI interface.¶
Following the initial exchange, the FHS Proxy/Server MAY later send additional periodic and/or event-driven unsolicited RA messages per [RFC4861]. (The unsolicited RAs may be initiated either by the FHS Proxy/Server itself or by the Hub via the FHS as a proxy.) The Client then continuously manages its underlying interfaces according to their states as follows:¶
The Client is responsible for retrying each RS exchange up to MAX_RTR_SOLICITATIONS times separated by RTR_SOLICITATION_INTERVAL seconds until an RA is received. If no RA is received over an UP underlying interface (i.e., even after attempting to contact alternate Proxy/Servers), the Client declares this underlying interface as DOWN. When changing to a new FHS or Hub Proxy/Server, the Client also includes a Proxy/Server Departure OMNI sub-option in new RS messages; the (new) FHS Proxy/Server will in turn send uNA messages to the old FHS and/or Hub Proxy/Server to announce the Client's departure as discussed in [I-D.templin-6man-aero].¶
The IPv6 layer sees the OMNI interface as an ordinary IPv6 interface. Therefore, when the IPv6 layer sends an RS message the OMNI interface returns an internally-generated RA message as though the message originated from an IPv6 router. The internally-generated RA message contains configuration information consistent with the information received from the RAs generated by the Hub Proxy/Server. Whether the OMNI interface IPv6 ND messaging process is initiated from the receipt of an RS message from the IPv6 layer or independently of the IPv6 layer is an implementation matter. Some implementations may elect to defer the OMNI interface internal RS/RA messaging process until an RS is received from the IPv6 layer, while others may elect to initiate the process proactively. Still other deployments may elect to administratively disable IPv6 layer RS/RA messaging over the OMNI interface, since the messages are not required to drive the OMNI interface internal RS/RA process. (Note that this same logic applies to IPv4 implementations that employ ICMP-based Router Discovery per [RFC1256].)¶
Note: The Router Lifetime value in RA messages indicates the time before which the Client must send another RS message over this underlying interface (e.g., 600 seconds), however that timescale may be significantly longer than the lifetime the MS has committed to retain the prefix registration (e.g., REACHABLETIME seconds). Proxy/Servers are therefore responsible for keeping MS state alive on a shorter timescale than the Client may be required to do on its own behalf.¶
Note: On certain multicast-capable underlying interfaces, Clients should send periodic unsolicited multicast NA messages and Proxy/Servers should send periodic unsolicited multicast RA messages as "beacons" that can be heard by other nodes on the link. If a node fails to receive a beacon after a timeout value specific to the link, it can initiate a unicast exchange to test reachability.¶
Note: If a single FHS Proxy/Server services multiple of a Client's underlying interfaces, Window Synchronization will initially be repeated for the RS/RA exchange over each underlying interface, i.e., until the Client discovers the many-to-one relationship.¶
Note: Although the Client's FHS Proxy/Server is a first-hop segment node from its own perspective, the Client stores the Proxy/Server's FMT/SRT/MSID/INADDR as last-hop segment (LHS) information. This allows both the Client and Hub Proxy/Server to supply the information to neighbors that will perceive it as LHS information on the return path to the Client.¶
Note: The Hub Proxy/Server injects Client MNP-ULAs into the routing system by simply creating a route-to-interface forwarding table entry for the MNP-ULA via the OMNI interface. The dynamic routing protocol will notice the new entry and advertise the MNP-ULA to its peers. If the Hub receives additional RS messages, it need not re-create the MNP-ULA forwarding table entry (nor disturb the dynamic routing protocol) if an entry is already present.¶
Note: If the Client's initial RS message includes an anycast *NET destination address, the FHS Proxy/Server returns the solicited RA using the same anycast address as the *NET source while including an Interface Attributes sub-option with omIndex '0' and its true unicast address in the INADDR. When the Client sends additional RS messages, it includes this FHS Proxy/Server unicast address as the *NET destination and the FHS Proxy/Server returns the solicited RA using the same unicast address as the *NET source. This will ensure that RS/RA exchanges are not impeded by any NATs on the path while avoiding long-term exposure of messages that use an anycast address as the source.¶
Note: The Origin Indication sub-option is included only by the FHS Proxy/Server and not by the Hub (unless the Hub is also serving as an FHS).¶
Note: Clients should set the N/A/U flags consistently in successive RS messages and only change those settings when an FHS/Hub Proxy/Server service profile update is necessary.¶
In environments where Identification window synchronization is necessary, the RS/RA exchanges discussed above observe the principles specified in Section 6.6. Window synchronization is conducted between the Client and each FHS Proxy/Server used to contact the Hub Proxy/Server, i.e., and not between the Client and the Hub. This is due to the fact that the Hub Proxy/Server is responsible only for forwarding all control and data messages via the secured spanning tree to FHS Proxy/Servers, and is not responsible for forwarding messages directly to the Client under a synchronized window. Also, in the reverse direction the FHS Proxy/Servers handle all default forwarding actions without forwarding Client-initiated data to the Hub.¶
When a Client needs to perform window synchronization via a new FHS Proxy/Server, it sets the RS source address to its own MNP-LLA and destination address to the ADM-LLA of the Hub Proxy/Server, then sets the SYN flag and includes an initial Sequence Number for Window Synchronization. The Client then performs OAL encapsulation using its own MNP-ULA as the source and the ADM-ULA of the FHS Proxy/Server as the destination and includes an Interface Attributes sub-option then forwards the resulting carrier packets to the FHS Proxy/Server. The FHS Proxy/Server then extracts the RS message and caches the Window Synchronization parameters then re-encapsulates with its own ADM-ULA as the source and the ADM-ULA of the Hub Proxy/Server as the target.¶
The FHS Proxy/Server then forwards the resulting carrier packets via the secured spanning tree to the Hub Proxy/Server, which updates the Client's Interface Attributes and returns a unicast RA message with source set to its own ADM-LLA and destination set to the Client's MNP-LLA and with the Client's Interface Attributes echoed. The Hub Proxy/Server then performs OAL encapsulation using its own ADM-ULA as the source and the ADM-ULA of the FHS Proxy/Server as the destination, then forwards the carrier packets via the secured spanning tree to the FHS Proxy/Server. The FHS Proxy/Server then re-encapsulates the message using its own ADM-ULA as the source, the MNP-ULA of the Client as the destination and includes responsive Window Synchronization information. The FHS Proxy/Server then forwards the message to the Client which updates its window synchronization information for the FHS Proxy/Server as necessary.¶
Following the initial RS/RA-driven window synchronization, the Client can re-assert new windows with specific FHS Proxy/Servers by performing NS/NA exchanges between its own MNP-LLA and the ADM-LLAs of the FHS Proxy/Servers without having to disturb the Hub.¶
On some *NETs, a Client may be located multiple IP hops away from the nearest OMNI link Proxy/Server. Forwarding through IP multihop *NETs is conducted through the application of a routing protocol (e.g., a MANET/VANET routing protocol over omni-directional wireless interfaces, an inter-domain routing protocol in an enterprise network, etc.).¶
A Client located potentially multiple *NET hops away from the nearest Proxy/Server prepares an RS message, sets the source address to its MNP-LLA (or to the unspecified address (::) if it does not yet have an MNP-LLA), and sets the destination to link-scoped All-Routers multicast or a unicast ADM-LLA the same as discussed above. The OMNI interface then employs OAL encapsulation, sets the OAL source address to the ULA corresponding to the RS source (or to a Temporary ULA if the RS source was the unspecified address (::)) and sets the OAL destination to an OMNI IPv6 anycast address based on either a native IPv6 or IPv4-mapped IPv6 prefix (see: Section 10).¶
For IPv6-enabled *NETs, if the underlying interface does not configure an IPv6 GUA the Client forwards the message without further encapsulation. Otherwise, the Client encapsulates the message in UDP/IPv6 *NET headers, sets the source to the underlying interface GUA and sets the destination to the same OMNI IPv6 anycast address. The Client then forwards the message into the IPv6 multihop routing system which conveys it to the nearest Proxy/Server that advertises a matching OMNI IPv6 anycast prefix.¶
For IPv4-only *NETs, the Client encapsulates the RS message in UDP/IPv4 *NET headers, sets the source to the underlying interface IPv4 address and sets the destination to the IPv4 anycast address TBD3 (see: IANA Considerations). The Client then forwards the message into the IPv4 multihop routing system which conveys it to the nearest Proxy/Server that advertises the corresponding IPv4 prefix. If the nearest Proxy/Server is too busy and/or does not configure the specified OMNI IPv6 anycast address, it should forward (without Proxying) the OAL-encapsulated RS to another nearby Proxy/Server connected to the same IPv4 (multihop) network that configures the OMNI IPv6 anycast address. (In environments where reciprocal RS forwarding cannot be supported, the first Proxy/Server should instead return an RA based on its own MSP(s).)¶
When an intermediate *NET hop that participates in the routing protocol receives the encapsulated RS, it forwards the message according to its routing tables (note that an intermediate node could be a fixed infrastructure element or another MANET/VANET node). This process repeats iteratively until the RS message is received by a penultimate *NET hop within single-hop communications range of a Proxy/Server, which forwards the message to the Proxy/Server.¶
When a Proxy/Server that configures the OMNI IPv6 anycast OAL destination receives the message, it decapsulates the RS and assumes either the Hub or FHS role (in which case, it forwards the RS to a candidate Hub). The Hub Proxy/Server then prepares an RA message with source address set to its own ADM-LLA and destination address set to the Client MNP-LLA. The Hub Proxy/Server then performs OAL encapsulation with the RA OAL source/destination set to the RS OAL destination/source and forwards the RA to the FHS Proxy/Server or directly to the Client.¶
When the Hub or FHS Proxy/Server forwards the RA to the Client, it encapsulates the message in *NET encapsulation headers (if necessary) with (src, dst) set to the (dst,src) of the RS *NET encapsulation headers. The Proxy/Server then forwards the message to a *NET node within communications range, which forwards the message according to its routing tables to an intermediate node. The multihop forwarding process within the *NET continues repetitively until the message is delivered to the original Client, which decapsulates the message and performs autoconfiguration the same as if it had received the RA directly from a Proxy/Server on the same physical link.¶
Note: When the RS message includes anycast OAL and/or *NET encapsulation destinations, the FHS Proxy/Server must use the same anycast addresses as the OAL and/or *NET encapsulation sources to support forwarding of the RA message and any initial data packets over any NATs on the path. When the Client receives the RA, it will discover the unicast OAL and/or IPv4 encapsulation addresses and can forward future packets using the unicast (instead of anycast) addresses to populate NAT state in the forward path. (If the Client does not have immediate data to send to the FHS Proxy/Server, it can instead send an OAL "bubble" - see Section 6.12.) After the Client begins using unicast OAL/*NET encapsulation addresses in this way, the FHS Proxy/Server should also begin using the same unicast addresses in the reverse direction.¶
Note: As an alternate approach to multihop forwarding via IPv6 encapsulation, the Client and Proxy/Server could statelessly translate the IPv6 LLAs into ULAs and forward the RS/RA messages without encapsulation. This would violate the [RFC4861] requirement that certain IPv6 ND messages must use link-local addresses and must not be accepted if received with Hop Limit less than 255. This document therefore mandates encapsulation since the overhead is nominal considering the infrequent nature and small size of IPv6 ND messages. Future documents may consider encapsulation avoidance through translation while updating [RFC4861].¶
Note: An alternate approach to multihop forwarding via IPv4 encapsulation would be to employ IPv6/IPv4 protocol translation. However, for IPv6 ND messages the LLAs would be truncated due to translation and the OMNI Router and Prefix Discovery services would not be able to function. The use of IPv4 encapsulation is therefore indicated.¶
When a Client is not pre-provisioned with an MNP-LLA (or, when the Client requires additional MNP delegations), it requests the MS to select MNPs on its behalf and set up the correct routing state. The DHCPv6 service [RFC8415] supports this requirement.¶
When a Client requires the MS to select MNPs, it sends an RS message with source set to the unspecified address (::) if it has no MNP_LLAs. If the Client requires only a single MNP delegation, it can then include a Node Identification sub-option in the OMNI option and set the OMNI extension header Preflen to the length of the desired MNP. If the Client requires multiple MNP delegations and/or more complex DHCPv6 services, it instead includes a DHCPv6 Message sub-option containing a Client Identifier, one or more IA_PD options and a Rapid Commit option then sets the 'msg-type' field to "Solicit", and includes a 3 octet 'transaction-id'. The Client then sets the RS destination to link-scoped All-Routers multicast and sends the message using OAL encapsulation and fragmentation if necessary as discussed above.¶
When the Hub Proxy/Server receives the RS message, it performs OAL reassembly if necessary. Next, if the RS source is the unspecified address (::) and/or the OMNI option includes a DHCPv6 message sub-option, the Hub Proxy/Server acts as a "Proxy DHCPv6 Client" in a message exchange with the locally-resident DHCPv6 server. If the RS did not contain a DHCPv6 message sub-option, the Hub Proxy/Server generates a DHCPv6 Solicit message on behalf of the Client using an IA_PD option with the prefix length set to the OMNI extension header Preflen value and with a Client Identifier formed from the OMNI option Node Identification sub-option; otherwise, the Hub Proxy/Server uses the DHCPv6 Solicit message contained in the OMNI option. The Hub Proxy/Server then sends the DHCPv6 message to the DHCPv6 Server, which delegates MNPs and returns a DHCPv6 Reply message with PD parameters. (If the Hub Proxy/Server wishes to defer creation of Client state until the DHCPv6 Reply is received, it can instead act as a Lightweight DHCPv6 Relay Agent per [RFC6221] by encapsulating the DHCPv6 message in a Relay-forward/reply exchange with Relay Message and Interface ID options. In the process, the Hub Proxy/Server packs any state information needed to return an RA to the Client in the Relay-forward Interface ID option so that the information will be echoed back in the Relay-reply.)¶
When the Hub Proxy/Server receives the DHCPv6 Reply, it create OMNI interface MNP-ULA forwarding table entries (i.e., to prompt the dynamic routing protocol) and creates MNP-LLAs based on the delegated MNPs. The Hub Proxy/Server then sends an RA back to the Client with the DHCPv6 Reply message included in an OMNI DHCPv6 message sub-option if and only if the RS message had included an explicit DHCPv6 Solicit. If the RS message source was the unspecified address (::), the Hub Proxy/Server includes one of the (newly-created) MNP-LLAs as the RA destination address and sets the OMNI extension header Preflen accordingly; otherwise, the Hub Proxy/Server includes the RS source address as the RA destination address. The Hub Proxy/Server then sets the RA source address to its own ADM-LLA, performs OAL encapsulation and fragmentation, performs *NET encapsulation and sends the RA to the Client (i.e., either directly or via an FHS Proxy/Server as discussed above). When the Client receives the RA, it reassembles and discards the OAL encapsulation, then creates a default route, assigns Subnet Router Anycast addresses and uses the RA destination address as its primary MNP-LLA. The Client will then use this primary MNP-LLA as the source address of any IPv6 ND messages it sends as long as it retains ownership of the MNP.¶
If the *NET link model is multiple access, the FHS Proxy/Server is responsible for assuring that address duplication cannot corrupt the neighbor caches of other nodes on the link. When the Client sends an RS message on a multiple access *NET link, the Proxy/Server verifies that the Client is authorized to use the address and responds with an RA (or forwards the RS to the Hub) only if the Client is authorized.¶
After verifying Client authorization and returning an RA, the Proxy/Server MAY return IPv6 ND Redirect messages to direct Clients located on the same *NET link to exchange packets directly without transiting the Proxy/Server. In that case, the Clients can exchange packets according to their unicast L2 addresses discovered from the Redirect message instead of using the dogleg path through the Proxy/Server. In some *NET links, however, such direct communications may be undesirable and continued use of the dogleg path through the Proxy/Server may provide better performance. In that case, the Proxy/Server can refrain from sending Redirects, and/or Clients can ignore them.¶
*NETs SHOULD deploy Proxy/Servers in Virtual Router Redundancy Protocol (VRRP) [RFC5798] configurations so that service continuity is maintained even if one or more Proxy/Servers fail. Using VRRP, the Client is unaware which of the (redundant) FHS Proxy/Servers is currently providing service, and any service discontinuity will be limited to the failover time supported by VRRP. Widely deployed public domain implementations of VRRP are available.¶
Proxy/Servers SHOULD use high availability clustering services so that multiple redundant systems can provide coordinated response to failures. As with VRRP, widely deployed public domain implementations of high availability clustering services are available. Note that special-purpose and expensive dedicated hardware is not necessary, and public domain implementations can be used even between lightweight virtual machines in cloud deployments.¶
In environments where fast recovery from Proxy/Server failure is required, FHS Proxy/Servers SHOULD use proactive Neighbor Unreachability Detection (NUD) in a manner that parallels Bidirectional Forwarding Detection (BFD) [RFC5880] to track Hub Proxy/Server reachability. FHS Proxy/Servers can then quickly detect and react to failures so that cached information is re-established through alternate paths. Proactive NUD control messaging is carried only over well-connected ground domain networks (i.e., and not low-end *NET links such as aeronautical radios) and can therefore be tuned for rapid response.¶
FHS Proxy/Servers perform proactive NUD for Hub Proxy/Servers for which there are currently active Clients on the *NET. If a Hub Proxy/Server fails, the FHS Proxy/Server can quickly inform Clients of the outage by sending multicast RA messages on the *NET interface. The FHS Proxy/Server sends RA messages to Clients via the *NET interface with source set to the ADM-LLA of the Hub, with destination address set to All-Nodes multicast (ff02::1) [RFC4291] and with Router Lifetime set to 0.¶
The FHS Proxy/Server SHOULD send MAX_FINAL_RTR_ADVERTISEMENTS RA messages separated by small delays [RFC4861]. Any Clients on the *NET interface that have been using the (now defunct) Hub Proxy/Server will receive the RA messages.¶
When a Client connects to an *NET link for the first time, it sends an RS message with an OMNI option. If the first hop router recognizes the option, it responds according to the appropriate FHS/Hub Proxy/Server role resulting in an RA message with an OMNI option returned to the Client. The Client then engages this FHS Proxy/Sever according to the OMNI link model specified above. If the first hop router is a legacy IPv6 router, however, it instead returns an RA message with no OMNI option and with a non-OMNI unicast source LLA as specified in [RFC4861]. In that case, the Client engages the *NET according to the legacy IPv6 link model and without the OMNI extensions specified in this document.¶
If the *NET link model is multiple access, there must be assurance that address duplication cannot corrupt the neighbor caches of other nodes on the link. When the Client sends an RS message on a multiple access *NET link with an LLA source address and an OMNI option, first hop routers that recognize the OMNI option ensure that the Client is authorized to use the address and return an RA with a non-zero Router Lifetime only if the Client is authorized. First hop routers that do not recognize the OMNI option instead return an RA that makes no statement about the Client's authorization to use the source address. In that case, the Client should perform Duplicate Address Detection to ensure that it does not interfere with other nodes on the link.¶
An alternative approach for multiple access *NET links to ensure isolation for Client-Proxy/Server communications is through L2 address mappings as discussed in Appendix D. This arrangement imparts a (virtual) point-to-point link model over the (physical) multiple access link.¶
Client OMNI interfaces configured over IPv6-enabled underlying interfaces on an open Internetwork without an OMNI-aware first-hop router receive IPv6 RA messages with no OMNI options, while OMNI interfaces configured over IPv4-only underlying interfaces receive no IPv6 RA messages at all (but may receive IPv4 RA messages [RFC1256]). Client OMNI interfaces that receive RA messages with OMNI options configure addresses, on-link prefixes, etc. on the underlying interface that received the RA according to standard IPv6 ND and address resolution conventions [RFC4861] [RFC4862]. Client OMNI interfaces configured over IPv4-only underlying interfaces configure IPv4 address information on the underlying interfaces using mechanisms such as DHCPv4 [RFC2131].¶
Client OMNI interfaces configured over underlying interfaces connected to open Internetworks can apply security services such as VPNs to connect to a Proxy/Server, or can establish a direct link to the Proxy/Server through some other means (see Section 4). In environments where an explicit VPN or direct link may be impractical, Client OMNI interfaces can instead send IPv6 ND messages with OMNI options that include authentication signatures.¶
OMNI interfaces use UDP/IP as *NET encapsulation headers for transmission over open Internetworks with UDP service port number 8060 (see: Section 25.13 and Section 3.6 of [I-D.templin-6man-aero]) for both IPv4 and IPv6 underlying interfaces. The OMNI interface submits original IP packets for OAL encapsulation, then encapsulates the resulting OAL fragments in UDP/IP *NET headers to form carrier packets. (The first four bits following the UDP header determine whether the OAL headers are uncompressed/compressed as discussed in Section 6.4.) The OMNI interface sets the UDP length to the encapsulated OAL fragment length and sets the IP length to an appropriate value at least as large as the UDP datagram.¶
For Client-Proxy/Server (e.g., "Vehicle-to-Infrastructure (V2I)") neighbor exchanges, the source must include an OMNI option with an authentication sub-option in all IPv6 ND messages. The source can apply HIP security services per [RFC7401] using the IPv6 ND message OMNI option as a "shipping container" to convey an authentication signature in a (unidirectional) HIP "Notify" message. For Client-Client (e.g., "Vehicle-to-Vehicle (V2V)") neighbor exchanges, two Clients can exchange HIP "Initiator/Responder" messages coded in OMNI options of multiple IPv6 NS/NA messages for mutual authentication according to the HIP protocol. (Note: a simple Hashed Message Authentication Code (HMAC) such as specified in [RFC4380] or the QUIC-TLS connection-oriented service [RFC9000] can be used as an alternate authentication service in some environments.)¶
When an OMNI interface includes an authentication sub-option, it must appear as the first sub-option of the first OMNI option in the IPv6 ND message which must appear immediately following the IPv6 ND message header. When an OMNI interface prepares a HIP message sub-option, it includes its own (H)HIT as the Sender's HIT and the neighbor's (H)HIT if known as the Receiver's HIT (otherwise 0). If (H)HITs are not available within the OMNI operational environment, the source can instead include other IPv6 address types instead of (H)HITs as long as the Sender and Receiver have some way to associate information embedded in the IPv6 address with the neighbor; such information could include a node identifier, vehicle identifier, MAC address, etc.¶
Before calculating the authentication signature, the source includes any other necessary sub-options (such as Interface Attributes and Origin Indication) and sets both the IPv6 ND message Checksum and authentication signature fields to 0. The source then calculates the authentication signature over the full length of the IPv6 ND message beginning with a pseudo-header of the IPv6 header (i.e., the same as specified in [RFC4443]) and extending over the length of the message. (If the IPv6 ND message is part of an OAL super-packet, the source instead calculates the authentication signature over the remainder of the super-packet up to but not including the trailing OAL Checksum field.) The source next writes the authentication signature into the sub-option signature field and forwards the message.¶
After establishing a VPN or preparing for UDP/IP encapsulation, OMNI interfaces send RS/RA messages for Client-Proxy/Server coordination (see: Section 15) and NS/NA messages for route optimization, window synchronization and mobility management (see: [I-D.templin-6man-aero]). These control plane messages must be authenticated while other control and data plane messages are delivered the same as for ordinary best-effort traffic with source address and/or Identification window-based data origin verification. Upper layer protocol sessions over OMNI interfaces that connect over open Internetworks without an explicit VPN should therefore employ transport- or higher-layer security to ensure authentication, integrity and/or confidentiality.¶
Clients should avoid using INET Proxy/Servers as general-purpose routers for steady streams of carrier packets that do not require authentication. Clients should instead coordinate with other INET nodes that can provide forwarding services instead of burdening the Proxy/Server (or preferably coordinate directly with peer Clients directly). Procedures for coordinating with peer Clients and discovering INET nodes that can provide better forwarding services are discussed in [I-D.templin-6man-aero].¶
Clients that attempt to contact peers over INET underlying interfaces often encounter NATs in the path. OMNI interfaces accommodate NAT traversal using UDP/IP encapsulation and the mechanisms discussed in [I-D.templin-6man-aero]. FHS Proxy/Servers include Origin Indications in RA messages to allow Clients to detect the presence of NATs.¶
Note: Following the initial IPv6 ND message exchange, OMNI interfaces configured over INET underlying interfaces maintain neighbor relationships by transmitting periodic IPv6 ND messages with OMNI options that include HIP "Update" and/or "Notify" messages. When HMAC authentication is used instead of HIP, the Client and Proxy/Server exchange all IPv6 ND messages with HMAC signatures included based on a shared-secret. When QUIC-TLS connections are used, the Client and Proxy/Server observe QUIC-TLS conventions [RFC9000][RFC9001].¶
Note: OMNI interfaces configured over INET underlying interfaces should employ the Identification window synchronization mechanisms specified in Section 6.6 in order to reject spurious carrier packets that might otherwise clutter the reassembly cache. This is especially important in environments where carrier packet spoofing and/or corruption is a threat.¶
Note: NATs may be present on the path from a Client to its FHS Proxy/Server, but never on the path from the FHS Proxy/Server to the Hub where only INET and/or spanning tree hops occur. Therefore, the FHS Proxy/Server does not communicate Client origin information to the Hub where it would serve no purpose.¶
In some use cases, it is desirable, beneficial and efficient for the Client to receive a constant MNP that travels with the Client wherever it moves. For example, this would allow air traffic controllers to easily track aircraft, etc. In other cases, however (e.g., intelligent transportation systems), the Client may be willing to sacrifice a modicum of efficiency in order to have time-varying MNPs that can be changed every so often to defeat adversarial tracking.¶
The prefix delegation services discussed in Section 15.3 allows Clients that desire time-varying MNPs to obtain short-lived prefixes to send RS messages with source set to the unspecified address (::) and/or with an OMNI option with DHCPv6 Option sub-options. The Client would then be obligated to renumber its internal networks whenever its MNP (and therefore also its OMNI address) changes. This should not present a challenge for Clients with automated network renumbering services, but may disrupt persistent sessions that would prefer to use a constant address.¶
Clients that generate (H)HITs but do not have pre-assigned MNPs can request MNP delegations by issuing IPv6 ND messages that use the (H)HIT instead of a Temporary ULA. In particular, when a Client creates an RS message it can set the source to the unspecified address (::) and destination to link-scoped All-Routers multicast. The IPv6 ND message includes an OMNI option with a HIP message sub-option, and need not include a Node Identification sub-option if the Client's HIT appears in the HIP message. The Client then encapsulates the message in an IPv6 header with the (H)HIT as the source address. The Client then sends the message as specified in Section 15.2.¶
When a Proxy/Server receives the RS message, it notes that the source was the unspecified address (::), then examines the OAL encapsulation source address to determine that the source is a (H)HIT and not a Temporary ULA. The Proxy/Server next invokes the DHCPv6 protocol to request an MNP prefix delegation while using the HIT (in the form of a DUID) as the Client Identifier, then prepares an RA message with source address set to its own ADM-LLA and destination set to the MNP-LLA corresponding to the delegated MNP. The Proxy/Server next includes an OMNI option with a HIP message sub-option and any DHCPv6 prefix delegation parameters. The Proxy/Server finally encapsulates the RA in an IPv6 header with source address set to its own ADM-ULA and destination set to the (H)HIT from the RS encapsulation source address, then returns the encapsulated RA to the Client.¶
Clients can also use (H)HITs and/or Temporary ULAs for direct Client-to-Client communications outside the context of any OMNI link supporting infrastructure. When two Clients encounter one another they can use their (H)HITs and/or Temporary ULAs as original IPv6 packet source and destination addresses to support direct communications. Clients can also inject their (H)HITs and/or Temporary ULAs into a MANET/VANET routing protocol to enable multihop communications. Clients can further exchange IPv6 ND messages (such as NS/NA) using their (H)HITs and/or Temporary ULAs as source and destination addresses.¶
Lastly, when Clients are within the coverage range of OMNI link infrastructure a case could be made for injecting (H)HITs and/or Temporary ULAs into the global MS routing system. For example, when the Client sends an RS to an FHS Proxy/Server it could include a request to inject the (H)HIT / Temporary ULA into the routing system instead of requesting an MNP prefix delegation. This would potentially enable OMNI link-wide communications using only (H)HITs or Temporary ULAs, and not MNPs. This document notes the opportunity, but makes no recommendation.¶
Clients use LLAs only for link-scoped communications on the OMNI link. Typically, Clients use LLAs as source/destination IPv6 addresses of IPv6 ND messages, but may also use them for addressing ordinary original IP packets exchanged with an OMNI link neighbor.¶
Clients use MNP-ULAs as source/destination IPv6 addresses in the encapsulation headers of OAL packets. Clients use Temporary ULAs for OAL addressing when an MNP-ULA is not available, or as source/destination IPv6 addresses for communications within a MANET/VANET local area. Clients can also use (H)HITs instead of Temporary ULAs when operation outside the context of a specific ULA domain and/or source address attestation is necessary.¶
Clients use MNP-based GUAs as original IP packet source and destination addresses for communications with Internet destinations when they are within range of OMNI link supporting infrastructure that can inject the MNP into the routing system.¶
Clients use anycast GUAs as OAL and/or *NET encapsulation destination addresses for RS messages used to discover the nearest FHS Proxy/Server. When the Proxy/Server returns a solicited RA, it must also use the same anycast address as the RA OAL/*NET encapsulation source in order to successfully traverse any NATs in the path. The Client should then immediately transition to using the FHS Proxy/Server's discovered unicast OAL/*NET address as the destination in order to minimize dependence on the Proxy/Server's use of an anycast source address.¶
An OAL destination or intermediate node may need to return ICMPv6-like error messages (e.g., Destination Unreachable, Packet Too Big, Time Exceeded, etc.) [RFC4443] to an OAL source. Since ICMPv6 error messages do not themselves include authentication codes, OAL nodes can return error messages as an OMNI ICMPv6 Error sub-option in a secured IPv6 ND uNA message.¶
The following IANA actions are requested in accordance with [RFC8126] and [RFC8726]:¶
The IANA is instructed to allocate an Internet Protocol number TBD1 from the 'protocol numbers' registry for the Overlay Multilink Network Interface (OMNI) protocol. Guidance is found in [RFC5237] (registration procedure is IESG Approval or Standards Action).¶
During final publication stages, the IESG will be requested to procure an IEEE EtherType value TBD2 for OMNI according to the statement found at https://www.ietf.org/about/groups/iesg/statements/ethertypes/.¶
Following this procurement, the IANA is instructed to register the value TBD2 in the 'ieee-802-numbers' registry for Overlay Multilink Network Interface (OMNI) encapsulation on Ethernet networks. Guidance is found in [RFC7042] (registration procedure is Expert Review).¶
The IANA is instructed to assign TBD3/N as an "OMNI IPv4 anycast" address/prefix in the "IPv4 Special-Purpose Address" registry. This specification recommends assigning the address 192.88.99.100/24 as the "OMNI IPv4 anycast" address/prefix, since the former use of the address/prefix 192.88.99.1/24 is deprecated by [RFC7526]. In the event that conflicts with the former use are deemed irreconcilable, the IANA is instructed to work with authors to determine an alternate TBD3/N address/prefix.¶
The IANA is instructed to allocate an official Type number TBD4 from the "IPv6 Neighbor Discovery Option Formats" registry for the OMNI option (registration procedure is RFC required). Implementations set Type to 253 as an interim value [RFC4727].¶
The IANA is instructed to allocate one Ethernet unicast address TBD5 (suggested value '00-52-14') in the 'ethernet-numbers' registry under "IANA Unicast 48-bit MAC Addresses" (registration procedure is Expert Review). The registration should appear as follows:¶
Addresses Usage Reference --------- ----- --------- 00-52-14 Overlay Multilink Network (OMNI) Interface [RFCXXXX]
The IANA is instructed to assign two new Code values in the "ICMPv6 Code Fields: Type 2 - Packet Too Big" registry (registration procedure is Standards Action or IESG Approval). The registry should appear as follows:¶
Code Name Reference --- ---- --------- 0 PTB Hard Error [RFC4443] 1 PTB Soft Error (loss) [RFCXXXX] 2 PTB Soft Error (no loss) [RFCXXXX]
(Note: this registry also to be used to define values for setting the "unused" field of ICMPv4 "Destination Unreachable - Fragmentation Needed" messages.)¶
The OMNI option defines a 5-bit Sub-Type field, for which IANA is instructed to create and maintain a new registry entitled "OMNI Option Sub-Type Values". Initial values are given below (registration procedure is RFC required):¶
Value Sub-Type name Reference ----- ------------- ---------- 0 Pad1 [RFCXXXX] 1 PadN [RFCXXXX] 2 Interface Attributes [RFCXXXX] 3 Multilink Fwding Parameters [RFCXXXX] 4 Traffic Selector [RFCXXXX] 5 Geo Coordinates [RFCXXXX] 6 DHCPv6 Message [RFCXXXX] 7 HIP Message [RFCXXXX] 8 PIM-SM Message [RFCXXXX] 9 Reassembly Limit [RFCXXXX] 10 Fragmentation Report [RFCXXXX] 11 Node Identification [RFCXXXX] 12 ICMPv6 Error [RFCXXXX] 13 QUIC-TLS Message [RFCXXXX] 14 Proxy/Server Departure [RFCXXXX] 15 OMNI Header Extension [RFCXXXX] 16-29 Unassigned 30 Sub-Type Extension [RFCXXXX] 31 Reserved by IANA [RFCXXXX]
The OMNI Geo Coordinates sub-option (see: Section 12.2.6) contains an 8-bit Type field, for which IANA is instructed to create and maintain a new registry entitled "OMNI Geo Coordinates Type Values". Initial values are given below (registration procedure is RFC required):¶
Value Sub-Type name Reference ----- ------------- ---------- 0 NULL [RFCXXXX] 1-252 Unassigned [RFCXXXX] 253-254 Reserved for Experimentation [RFCXXXX] 255 Reserved by IANA [RFCXXXX]
The OMNI Node Identification sub-option (see: Section 12.2.12) contains an 8-bit ID-Type field, for which IANA is instructed to create and maintain a new registry entitled "OMNI Node Identification ID-Type Values". Initial values are given below (registration procedure is RFC required):¶
Value Sub-Type name Reference ----- ------------- ---------- 0 UUID [RFCXXXX] 1 HIT [RFCXXXX] 2 HHIT [RFCXXXX] 3 Network Access Identifier [RFCXXXX] 4 FQDN [RFCXXXX] 5 IPv6 Address [RFCXXXX] 6-252 Unassigned [RFCXXXX] 253-254 Reserved for Experimentation [RFCXXXX] 255 Reserved by IANA [RFCXXXX]
The OMNI option defines an 8-bit Extension-Type field for Sub-Type 30 (Sub-Type Extension), for which IANA is instructed to create and maintain a new registry entitled "OMNI Option Sub-Type Extension Values". Initial values are given below (registration procedure is RFC required):¶
Value Sub-Type name Reference ----- ------------- ---------- 0 RFC4380 UDP/IP Header Option [RFCXXXX] 1 RFC6081 UDP/IP Trailer Option [RFCXXXX] 2-252 Unassigned 253-254 Reserved for Experimentation [RFCXXXX] 255 Reserved by IANA [RFCXXXX]
The OMNI Sub-Type Extension "RFC4380 UDP/IP Header Option" defines an 8-bit Header Type field, for which IANA is instructed to create and maintain a new registry entitled "OMNI RFC4380 UDP/IP Header Option". Initial registry values are given below (registration procedure is RFC required):¶
Value Sub-Type name Reference ----- ------------- ---------- 0 Origin Indication (IPv4) [RFC4380] 1 Authentication Encapsulation [RFC4380] 2 Origin Indication (IPv6) [RFCXXXX] 3-252 Unassigned 253-254 Reserved for Experimentation [RFCXXXX] 255 Reserved by IANA [RFCXXXX]
The OMNI Sub-Type Extension for "RFC6081 UDP/IP Trailer Option" defines an 8-bit Trailer Type field, for which IANA is instructed to create and maintain a new registry entitled "OMNI RFC6081 UDP/IP Trailer Option". Initial registry values are given below (registration procedure is RFC required):¶
Value Sub-Type name Reference ----- ------------- ---------- 0 Unassigned 1 Nonce [RFC6081] 2 Unassigned 3 Alternate Address (IPv4) [RFC6081] 4 Neighbor Discovery Option [RFC6081] 5 Random Port [RFC6081] 6 Alternate Address (IPv6) [RFCXXXX] 7-252 Unassigned 253-254 Reserved for Experimentation [RFCXXXX] 255 Reserved by IANA [RFCXXXX]
The IANA has assigned the UDP port number "8060" for an earlier experimental version of AERO [RFC6706]. This document reclaims the UDP port number "8060" for 'aero' as the service port for UDP/IP encapsulation. (Note that, although [RFC6706] was not widely implemented or deployed, any messages coded to that specification can be easily distinguished and ignored since they use an invalid ICMPv6 message type number '0'.) The IANA is therefore instructed to update the reference for UDP port number "8060" from "RFC6706" to "RFCXXXX" (i.e., this document) while retaining the existing name 'aero'.¶
The IANA has assigned a 4 octet Private Enterprise Number (PEN) code "45282" in the "enterprise-numbers" registry. This document is the normative reference for using this code in DHCP Unique IDentifiers based on Enterprise Numbers ("DUID-EN for OMNI Interfaces") (see: Section 11). The IANA is therefore instructed to change the enterprise designation for PEN code "45282" from "LinkUp Networks" to "Overlay Multilink Network Interface (OMNI)".¶
The IANA has assigned the ifType code "301 - omni - Overlay Multilink Network Interface (OMNI)" in accordance with Section 6 of [RFC8892]. The registration appears under the IANA "Structure of Management Information (SMI) Numbers (MIB Module Registrations) - Interface Types (ifType)" registry.¶
No further IANA actions are required.¶
Security considerations for IPv4 [RFC0791], IPv6 [RFC8200] and IPv6 Neighbor Discovery [RFC4861] apply. OMNI interface IPv6 ND messages SHOULD include Nonce and Timestamp options [RFC3971] when transaction confirmation and/or time synchronization is needed. (Note however that when OAL encapsulation is used the (echoed) OAL Identification value can provide sufficient transaction confirmation.)¶
Client OMNI interfaces configured over secured ANET interfaces inherit the physical and/or link-layer security properties (i.e., "protected spectrum") of the connected ANETs. Client OMNI interfaces configured over open INET interfaces can use symmetric securing services such as VPNs or can by some other means establish a direct link. When a VPN or direct link may be impractical, however, the security services specified in [RFC7401] and/or [RFC4380] can be employed. While the OMNI link protects control plane messaging, applications must still employ end-to-end transport- or higher-layer security services to protect the data plane.¶
Strong network layer security for control plane messages and forwarding path integrity for data plane messages between Proxy/Servers MUST be supported. In one example, the AERO service [I-D.templin-6man-aero] constructs an SRT spanning tree with Proxy/Serves as leaf nodes and secures the spanning tree links with network layer security mechanisms such as IPsec [RFC4301] or WireGuard. Secured control plane messages are then constrained to travel only over the secured spanning tree paths and are therefore protected from attack or eavesdropping. Other control and data plane messages can travel over route optimized paths that do not strictly follow the secured spanning tree, therefore end-to-end sessions should employ transport- or higher-layer security services. Additionally, the OAL Identification value can provide a first level of data origin authentication to mitigate off-path spoofing in some environments.¶
Identity-based key verification infrastructure services such as iPSK may be necessary for verifying the identities claimed by Clients. This requirement should be harmonized with the manner in which (H)HITs are attested in a given operational environment.¶
Security considerations for specific access network interface types are covered under the corresponding IP-over-(foo) specification (e.g., [RFC2464], [RFC2492], etc.).¶
Security considerations for IPv6 fragmentation and reassembly are discussed in Section 6.10. In environments where spoofing is considered a threat, OMNI nodes SHOULD employ Identification window synchronization and OAL destinations SHOULD configure an (end-system-based) firewall.¶
AERO/OMNI Release-3.2 was tagged on March 30, 2021, and is undergoing internal testing. Additional internal releases expected within the coming months, with first public release expected end of 1H2021.¶
Many AERO/OMNI functions are implemented and undergoing final integration. OAL fragmentation/reassembly buffer management code has been cleared for public release.¶
This document does not itself update other RFCs, but suggests that the following could be updated through future IETF initiatives:¶
Updates can be through, e.g., standards action, the errata process, etc. as appropriate.¶
The first version of this document was prepared per the consensus decision at the 7th Conference of the International Civil Aviation Organization (ICAO) Working Group-I Mobility Subgroup on March 22, 2019. Consensus to take the document forward to the IETF was reached at the 9th Conference of the Mobility Subgroup on November 22, 2019. Attendees and contributors included: Guray Acar, Danny Bharj, Francois D'Humieres, Pavel Drasil, Nikos Fistas, Giovanni Garofolo, Bernhard Haindl, Vaughn Maiolla, Tom McParland, Victor Moreno, Madhu Niraula, Brent Phillips, Liviu Popescu, Jacky Pouzet, Aloke Roy, Greg Saccone, Robert Segers, Michal Skorepa, Michel Solery, Stephane Tamalet, Fred Templin, Jean-Marc Vacher, Bela Varkonyi, Tony Whyman, Fryderyk Wrobel and Dongsong Zeng.¶
The following individuals are acknowledged for their useful comments: Amanda Barber, Stuart Card, Donald Eastlake, Michael Matyas, Robert Moskowitz, Madhu Niraula, Greg Saccone, Stephane Tamalet, Eduard Vasilenko, Eric Vyncke. Pavel Drasil, Zdenek Jaron and Michal Skorepa are especially recognized for their many helpful ideas and suggestions. Akash Agarwal, Madhuri Madhava Badgandi, Sean Dickson, Don Dillenburg, Joe Dudkowski, Vijayasarathy Rajagopalan, Ron Sackman, Bhargava Raman Sai Prakash and Katherine Tran are acknowledged for their hard work on the implementation and technical insights that led to improvements for the spec.¶
Discussions on the IETF 6man and atn mailing lists during the fall of 2020 suggested additional points to consider. The authors gratefully acknowledge the list members who contributed valuable insights through those discussions. Eric Vyncke and Erik Kline were the intarea ADs, while Bob Hinden and Ole Troan were the 6man WG chairs at the time the document was developed; they are all gratefully acknowledged for their many helpful insights. Many of the ideas in this document have further built on IETF experiences beginning in the 1990s, with insights from colleagues including Ron Bonica, Brian Carpenter, Ralph Droms, Christian Huitema, Thomas Narten, Dave Thaler, Joe Touch, and many others who deserve recognition.¶
Early observations on IP fragmentation performance implications were noted in the 1986 Digital Equipment Corporation (DEC) "qe reset" investigation, where fragment bursts from NFS UDP traffic triggered hardware resets resulting in communication failures. Jeff Chase, Fred Glover and Chet Juzsczak of the Ultrix Engineering Group led the investigation, and determined that setting a smaller NFS mount block size reduced the amount of fragmentation and suppressed the resets. Early observations on L2 media MTU issues were noted in the 1988 DEC FDDI investigation, where Raj Jain, KK Ramakrishnan and Kathy Wilde represented architectural considerations for FDDI networking in general including FDDI/Ethernet bridging. Jeff Mogul (who led the IETF Path MTU Discovery working group) and other DEC colleagues who supported these early investigations are also acknowledged.¶
Throughout the 1990's and into the 2000's, many colleagues supported and encouraged continuation of the work. Beginning with the DEC Project Sequoia effort at the University of California, Berkeley, then moving to the DEC research lab offices in Palo Alto CA, then to Sterling Software at the NASA Ames Research Center, then to SRI in Menlo Park, CA, then to Nokia in Mountain View, CA and finally to the Boeing Company in 2005 the work saw continuous advancement through the encouragement of many. Those who offered their support and encouragement are gratefully acknowledged.¶
This work is aligned with the NASA Safe Autonomous Systems Operation (SASO) program under NASA contract number NNA16BD84C.¶
This work is aligned with the FAA as per the SE2025 contract number DTFAWA-15-D-00030.¶
This work is aligned with the Boeing Information Technology (BIT) Mobility Vision Lab (MVL) program.¶
The OAL Checksum Algorithm adopts the 8-bit Fletcher algorithm specified in Appendix I of [RFC1146] as also analyzed in [CKSUM]. [RFC6247] declared [RFC1146] historic for the reason that the algorithms had never seen widespread use with TCP, however this document adopts the 8-bit Fletcher algorithm for a different purpose. Quoting from Appendix I of [RFC1146], the OAL Checksum Algorithm proceeds as follows:¶
"The 8-bit Fletcher Checksum Algorithm is calculated over a sequence of data octets (call them D[1] through D[N]) by maintaining 2 unsigned 1's-complement 8-bit accumulators A and B whose contents are initially zero, and performing the following loop where i ranges from 1 to N:¶
It can be shown that at the end of the loop A will contain the 8-bit 1's complement sum of all octets in the datagram, and that B will contain (N)D[1] + (N-1)D[2] + ... + D[N]."¶
To calculate the OAL checksum, the above algorithm is applied over the N-octet concatenation of the OAL pseudo-header, the encapsulated IP packet and the two-octet trailing checksum field initialized to 0. Specifically, the algorithm is first applied over the 40 octets of the OAL pseudo-header as data octets D[1] through D[40], then continues over the entire length of the original IP packet as data octets D[41] through D[N-2] and finally concludes with the two trailing 0 octets as data octets D[N-1] and D[N].¶
OMNI interface IPv6 ND messages are subject to authentication and integrity checks at multiple levels. When an OMNI interface sends an IPv6 ND message over an INET interface, it includes an authentication sub-option with a valid signature but does not include an IPv6 ND message checksum. The OMNI interface that receives the message verifies the OAL checksum as a first-level integrity check, then verifies the authentication signature (while ignoring the IPv6 ND message checksum) to ensure IPv6 ND message authentication and integrity.¶
When an OMNI interface sends an IPv6 ND message over an underlying interface connected to a secured network, it omits the authentication sub-option but instead calculates/includes an IPv6 ND message checksum. The OMNI interface that receives the message applies any lower-layer authentication and integrity checks, then verifies both the OAL checksum (if present) and the IPv6 ND message checksum. (Note that optimized implementations can verify both the OAL and IPv6 ND message checksums in a single pass over the data.) When an OMNI interface sends IPv6 ND messages to a synchronized neighbor, it includes an authentication sub-option only if authentication is necessary; otherwise, it calculates/includes the IPv6 ND message checksum.¶
When the OMNI interface calculates the authentication signature or IPv6 ND message checksum, it performs the calculation beginning with a pseudo-header of the IPv6 ND message header and extends over all following OAL packet data up to but not including the trailing OAL checksum field. In particular, for OAL super-packets any additional original IP packets included beyond the end of the IPv6 ND message are simply considered as extensions of the IPv6 ND message for the purpose of the calculation.¶
OAL destinations discard carrier packets with unacceptable Identifications and submit the encapsulated fragments in others for reassembly. The reassembly algorithm rejects any fragments with unacceptable sizes, offsets, etc. and reassembles all others. Following reassembly, the OAL checksum algorithm provides an integrity assurance layer that compliments any integrity checks already applied by lower layers as well as a first-pass filter for any checks that will be applied later by upper layers.¶
ICAO Doc 9776 is the "Technical Manual for VHF Data Link Mode 2" (VDLM2) that specifies an essential radio frequency data link service for aircraft and ground stations in worldwide civil aviation air traffic management. The VDLM2 link type is "multicast capable" [RFC4861], but with considerable differences from common multicast links such as Ethernet and IEEE 802.11.¶
First, the VDLM2 link data rate is only 31.5Kbps - multiple orders of magnitude less than most modern wireless networking gear. Second, due to the low available link bandwidth only VDLM2 ground stations (i.e., and not aircraft) are permitted to send broadcasts, and even so only as compact layer 2 "beacons". Third, aircraft employ the services of ground stations by performing unicast RS/RA exchanges upon receipt of beacons instead of listening for multicast RA messages and/or sending multicast RS messages.¶
This beacon-oriented unicast RS/RA approach is necessary to conserve the already-scarce available link bandwidth. Moreover, since the numbers of beaconing ground stations operating within a given spatial range must be kept as sparse as possible, it would not be feasible to have different classes of ground stations within the same region observing different protocols. It is therefore highly desirable that all ground stations observe a common language of RS/RA as specified in this document.¶
Note that links of this nature may benefit from compression techniques that reduce the bandwidth necessary for conveying the same amount of data. The IETF lpwan working group is considering possible alternatives: [https://datatracker.ietf.org/wg/lpwan/documents].¶
Per [RFC4861], IPv6 ND messages may be sent to either a multicast or unicast link-scoped IPv6 destination address. However, IPv6 ND messaging should be coordinated between the Client and Proxy/Server only without invoking other nodes on the *NET. This implies that Client-Proxy/Server control messaging should be isolated and not overheard by other nodes on the link.¶
To support Client-Proxy/Server isolation on some *NET links, Proxy/Servers can maintain an OMNI-specific unicast L2 address ("MSADDR"). For Ethernet-compatible *NETs, this specification reserves one Ethernet unicast address TBD5 (see: IANA Considerations). For non-Ethernet statically-addressed *NETs, MSADDR is reserved per the assigned numbers authority for the *NET addressing space. For still other *NETs, MSADDR may be dynamically discovered through other means, e.g., L2 beacons.¶
Clients map the L3 addresses of all IPv6 ND messages they send (i.e., both multicast and unicast) to MSADDR instead of to an ordinary unicast or multicast L2 address. In this way, all of the Client's IPv6 ND messages will be received by Proxy/Servers that are configured to accept packets destined to MSADDR. Note that multiple Proxy/Servers on the link could be configured to accept packets destined to MSADDR, e.g., as a basis for supporting redundancy.¶
Therefore, Proxy/Servers must accept and process packets destined to MSADDR, while all other devices must not process packets destined to MSADDR. This model has well-established operational experience in Proxy Mobile IPv6 (PMIP) [RFC5213][RFC6543].¶
<< RFC Editor - remove prior to publication >>¶
Differences from earlier versions to draft-templin-6man-omni-45:¶