Transmission of IP Packets over Overlay Multilink Network (OMNI) Interfaces

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶

This Internet-Draft will expire on 7 March 2022.¶

Copyright Notice

Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved.¶

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.¶

Table of Contents

1. Introduction

Mobile network platforms and devices (e.g., aircraft of various configurations, terrestrial vehicles, seagoing vessels, enterprise wireless devices, pedestrians with cellphones, etc.) configure mobile routers with multiple interface connections to wireless and/or wired-line data links. These data links may have diverse performance, cost and availability properties that can change dynamically according to mobility patterns, flight phases, proximity to infrastructure, etc. The mobile router acts as a Client of a network-based Mobility Service (MS) by configuring a virtual interface over its underlying interface data link connections to support the "6M's of modern Internetworking" (see below).¶

Each Client configures a virtual interface (termed the "Overlay Multilink Network Interface (OMNI)") as a thin layer over its underlying interfaces. The OMNI interface is therefore the only interface abstraction exposed to the IP layer and behaves according to the Non-Broadcast, Multiple Access (NBMA) interface principle, while underlying interfaces appear as link layer communication channels in the architecture. The OMNI interface internally employs the "OMNI Adaptation Layer (OAL)" to ensure that original IP packets are delivered without loss due to size restrictions. The OMNI interface connects to a virtual overlay service known as the "OMNI link". The OMNI link spans one or more Internetworks that may include private-use infrastructures and/or the global public Internet itself.¶

The Client's OMNI interface interacts with the MS and/or other Clients through IPv6 Neighbor Discovery (ND) control message exchanges [RFC4861]. The MS consists of a distributed set of service nodes known as Proxy/Servers (and other infrastructure elements) that also configure OMNI interfaces. An example MS termed "Automatic Extended Route Optimization (AERO)" appears in [I-D.templin-6man-aero]. In terms of precedence, the AERO specification may provide first-principle insights into a representative mobility service architecture as useful context for this specification.¶

Each OMNI interface provides a multilink nexus for exchanging inbound and outbound traffic via the correct underlying interface(s). The IP layer sees the OMNI interface as a point of connection to the OMNI link. Each OMNI link has one or more associated Mobility Service Prefixes (MSPs), which are typically IP Global Unicast Address (GUA) prefixes assigned to the link and from which Mobile Network Prefixes (MNPs) are derived. If there are multiple OMNI links, the IP layer will see multiple OMNI interfaces.¶

Each Client receives an MNP through IPv6 ND control message exchanges with Proxy/Servers. The Client uses the MNP for numbering downstream-attached End User Networks (EUNs) independently of the access network data links selected for data transport. The Client acts as a mobile router on behalf of its EUNs, and uses OMNI interface control messaging to coordinate with Proxy/Servers and/or other Clients. The Client iterates its control messaging over each of the OMNI interface's underlying interfaces in order to register each interface with the MS (see Section 15).¶

Clients may connect to multiple distinct OMNI links within the same OMNI domain by configuring multiple OMNI interfaces, e.g., omni0, omni1, omni2, etc. Each OMNI interface is configured over a set of underlying interfaces and provides a nexus for Safety-Based Multilink (SBM) operation. Each OMNI interface within the same OMNI domain configures a common ULA prefix [ULA]::/48, and configures a unique 16-bit Subnet ID '*' to construct the sub-prefix [ULA*]::/64 (see: Section 9). The IP layer applies SBM routing to select a specific OMNI interface, then the selected OMNI interface applies Performance-Based Multilink (PBM) internally to select appropriate underlying interfaces. Applications select SBM topologies based on IP layer Segment Routing [RFC8402], while each OMNI interface orchestrates PBM internally based on OMNI layer Segment Routing.¶

OMNI provides a link model suitable for a wide range of use cases. In particular, the International Civil Aviation Organization (ICAO) Working Group-I Mobility Subgroup is developing a future Aeronautical Telecommunications Network with Internet Protocol Services (ATN/IPS) and has issued a liaison statement requesting IETF adoption [ATN] in support of ICAO Document 9896 [ATN-IPS]. The IETF IP Wireless Access in Vehicular Environments (ipwave) working group has further included problem statement and use case analysis for OMNI in a document now in AD evaluation for RFC publication [I-D.ietf-ipwave-vehicular-networking]. Still other communities of interest include AEEC, RTCA Special Committee 228 (SC-228) and NASA programs that examine commercial aviation, Urban Air Mobility (UAM) and Unmanned Air Systems (UAS). Pedestrians with handheld devices represent another large class of potential OMNI users.¶

OMNI supports the "6M's of modern Internetworking" including:¶

1. Multilink - a Client's ability to coordinate multiple diverse underlying data links as a single logical unit (i.e., the OMNI interface) to achieve the required communications performance and reliability objectives.¶
2. Multinet - the ability to span the OMNI link over a segment routing topology with multiple diverse administrative domain network segments while maintaining seamless end-to-end communications between mobile Clients and correspondents such as air traffic controllers, fleet administrators, etc.¶
3. Mobility - a Client's ability to change network points of attachment (e.g., moving between wireless base stations) which may result in an underlying interface address change, but without disruptions to ongoing communication sessions with peers over the OMNI link.¶
4. Multicast - the ability to send a single network transmission that reaches multiple Clients belonging to the same interest group, but without disturbing other Clients not subscribed to the interest group.¶
5. Multihop - a mobile Client vehicle-to-vehicle relaying capability useful when multiple forwarding hops between vehicles may be necessary to "reach back" to an infrastructure access point connection to the OMNI link.¶
6. MTU assurance - the ability to deliver packets of various robust sizes between peers without loss due to a link size restriction, and to dynamically adjust packets sizes to achieve the optimal performance for each independent traffic flow.¶

This document specifies the transmission of IP packets and control messages over OMNI interfaces. The OMNI interface supports either IP protocol version (i.e., IPv4 [RFC0791] or IPv6 [RFC8200]) as the network layer data plane, while using IPv6 ND messaging as the control plane independently of the data plane IP protocol(s). The OAL operates as a sublayer between L3 and L2 based on IPv6 encapsulation [RFC2473] as discussed in the following sections.¶

2. Terminology

The terminology in the normative references applies; especially, the terms "link" and "interface" are the same as defined in the IPv6 [RFC8200] and IPv6 Neighbor Discovery (ND) [RFC4861] specifications. Additionally, this document assumes the following IPv6 ND message types: Router Solicitation (RS), Router Advertisement (RA), Neighbor Solicitation (NS), Neighbor Advertisement (NA) and Redirect. Clients and Proxy/Servers that implement IPv6 ND maintain per-neighbor state in Neighbor Cache Entries (NCEs). Each NCE is indexed by the neighbor's Link-Local Address (LLA), while the Unique-Local Address (ULA) used for encapsulation provides context for Identification verification.¶

The Protocol Constants defined in Section 10 of [RFC4861] are used in their same format and meaning in this document. The terms "All-Routers multicast", "All-Nodes multicast" and "Subnet-Router anycast" are the same as defined in [RFC4291] (with Link-Local scope assumed).¶

The term "IP" is used to refer collectively to either Internet Protocol version (i.e., IPv4 [RFC0791] or IPv6 [RFC8200]) when a specification at the layer in question applies equally to either version.¶

The following terms are defined within the scope of this document:¶

Client

a network platform/device mobile router that has one or more distinct upstream data link connections grouped together into one or more logical units. The Client's data link connection parameters can change over time due to, e.g., node mobility, link quality, etc. The Client further connects downstream-attached End User Networks (EUNs).¶

End User Network (EUN)

a simple or complex downstream-attached mobile network that travels with the Client as a single logical unit. The IP addresses assigned to EUN devices remain stable even if the Client's upstream data link connections change.¶

Mobility Service (MS)

a mobile routing service that tracks Client movements and ensures that Clients remain continuously reachable even across mobility events. The MS consists of the set of all Proxy/Servers (and any other supporting infrastructure nodes) for the OMNI link. Specific MS details are out of scope for this document, with an example found in [I-D.templin-6man-aero].¶

Proxy/Server

a segment routing topology edge node that provides Clients with a multi-purpose interface to the MS. As a server, the Proxy/Server responds directly to some Client IPv6 ND messages. As a proxy, the Proxy/Server forwards other Client IPv6 ND messages to other Proxy/Servers and Clients. As a router, the Proxy/Server provides a forwarding service for ordinary data packets that may be essential in some environments and a last resort in others.¶

First-Hop Segment (FHS) Proxy/Server

a Proxy/Server reached via an underlying interface of the source Client that forwards packets sent by the source Client over that interface into the segment routing topology. FHS Proxy/Servers act as intermediate forwarding nodes to facilitate RS/RA exchanges between a Client and its Hub Proxy/Server.¶

Last-Hop Segment (LHS) Proxy/Server

a Proxy/Server for an underlying interface of the target Client that forwards packets received from the segment routing topology to the target Client over that interface.¶

Hub Proxy/Server

a single Proxy/Server selected by the Client that provides a designated router service for all of the Client's underlying interfaces. Clients normally select the first FHS Proxy/Server they coordinate with to serve in the Hub role (as all FHS Proxy/Servers are equally capable candidates to serve in that capacity), however the Hub can also be any available Proxy/Server for the OMNI link (as there is no requirement that the Hub must also be one of the Client's FHS Proxy/Servers).¶

Segment Routing Topology (SRT)

a multinet forwarding region between the FHS Proxy/Server and LHS Proxy/Server. FHS/LHS Proxy/Servers and the SRT span the OMNI link on behalf of source/target Client pairs using segment routing in a manner outside the scope of this document (see: [I-D.templin-6man-aero]).¶

Mobility Service Prefix (MSP)

an aggregated IP Global Unicast Address (GUA) prefix (e.g., 2001:db8::/32, 192.0.2.0/24, etc.) assigned to the OMNI link and from which more-specific Mobile Network Prefixes (MNPs) are delegated. OMNI link administrators typically obtain MSPs from an Internet address registry, however private-use prefixes can alternatively be used subject to certain limitations (see: Section 10). OMNI links that connect to the global Internet advertise their MSPs to their interdomain routing peers.¶

Mobile Network Prefix (MNP)

a longer IP prefix delegated from an MSP (e.g., 2001:db8:1000:2000::/56, 192.0.2.8/30, etc.) and assigned to a Client. Clients sub-delegate the MNP to devices located in EUNs. Note that OMNI link Relay nodes may also service non-MNP routes (i.e., GUA prefixes not covered by an MSP) but that these correspond to fixed correspondent nodes and not Clients. Other than this distinction, MNP and non-MNP routes are treated exactly the same by the OMNI routing system.¶

Access Network (ANET)

a data link service network (e.g., an aviation radio access network, satellite service provider network, cellular operator network, WiFi network, etc.) that connects Clients. Physical and/or data link level security is assumed, and sometimes referred to as "protected spectrum". Private enterprise networks and ground domain aviation service networks may provide multiple secured IP hops between the Client's point of connection and the nearest Proxy/Server.¶

ANET interface

a Client's attachment to a link in an ANET.¶

Internetwork (INET)

a connected network region with a coherent IP addressing plan that provides transit forwarding services between ANETs and nodes that connect directly to the open INET via unprotected media. No physical and/or data link level security is assumed, therefore security must be applied by upper layers. The global public Internet itself is an example.¶

INET interface

a node's attachment to a link in an INET.¶

*NET

a "wildcard" term used when a given specification applies equally to both ANET and INET cases.¶

INADDR

the IP address (and also the UDP port number when UDP is used) that appear in *NET header address fields. The terms "*NET address" and "INADDR" are used interchangeably.¶

OMNI link

a Non-Broadcast, Multiple Access (NBMA) virtual overlay configured over one or more INETs and their connected ANETs. An OMNI link may comprise multiple distinct segments joined by bridges the same as for any link; the addressing plans in each segment may be mutually exclusive and managed by different administrative entities. Proxy/Servers and other MS infrastructure elements extend the link to support communications between Clients as single-hop neighbors.¶

OMNI interface

a node's attachment to an OMNI link, and configured over one or more underlying *NET interfaces. If there are multiple OMNI links in an OMNI domain, a separate OMNI interface is configured for each link.¶

OMNI Adaptation Layer (OAL)

an OMNI interface sublayer service whereby original IP packets admitted into the interface are wrapped in an IPv6 header and subject to fragmentation and reassembly. The OAL is also responsible for generating MTU-related control messages as necessary, and for providing addressing context for OMNI link SRT traversal.¶

original IP packet

a whole IP packet or fragment admitted into the OMNI interface by the network layer prior to OAL encapsulation and fragmentation, or an IP packet delivered to the network layer by the OMNI interface following OAL decapsulation and reassembly.¶

OAL packet

an original IP packet encapsulated in OAL headers and trailers, which is then submitted for OAL fragmentation and reassembly.¶

OAL fragment

a portion of an OAL packet following fragmentation but prior to *NET encapsulation, or following *NET encapsulation but prior to OAL reassembly.¶

(OAL) atomic fragment

an OAL packet that does not require fragmentation is always encapsulated as an "atomic fragment" with a Fragment Header with Fragment Offset and More Fragments both set to 0, but with a valid Identification value.¶

(OAL) carrier packet

an encapsulated OAL fragment following *NET encapsulation or prior to *NET decapsulation. OAL sources and destinations exchange carrier packets over underlying interfaces, and may be separated by one or more OAL intermediate nodes. OAL intermediate nodes may perform re-encapsulation on carrier packets by removing the *NET headers of the first hop network and replacing them with new *NET headers for the next hop network.¶

OAL source

an OMNI interface acts as an OAL source when it encapsulates original IP packets to form OAL packets, then performs OAL fragmentation and *NET encapsulation to create carrier packets.¶

OAL destination

an OMNI interface acts as an OAL destination when it decapsulates carrier packets, then performs OAL reassembly and decapsulation to derive the original IP packet.¶

OAL intermediate node

an OMNI interface acts as an OAL intermediate node when it removes the *NET headers of carrier packets received on a first segment, then re-encapsulates the carrier packets in new *NET headers and forwards them into the next segment.¶

OMNI Option

an IPv6 Neighbor Discovery option providing multilink parameters for the OMNI interface as specified in Section 12.¶

Mobile Network Prefix Link Local Address (MNP-LLA)

an IPv6 Link Local Address that embeds the most significant 64 bits of an MNP in the lower 64 bits of fe80::/64, as specified in Section 8.¶

Mobile Network Prefix Unique Local Address (MNP-ULA)

an IPv6 Unique-Local Address derived from an MNP-LLA.¶

Administrative Link Local Address (ADM-LLA)

an IPv6 Link Local Address that embeds a 32-bit administratively-assigned identification value in the lower 32 bits of fe80::/96, as specified in Section 8.¶

Administrative Unique Local Address (ADM-ULA)

an IPv6 Unique-Local Address derived from an ADM-LLA.¶

Multilink

an OMNI interface's manner of managing diverse underlying interface connections to data links as a single logical unit. The OMNI interface provides a single unified interface to upper layers, while underlying interface selections are performed on a per-packet basis considering traffic selectors such as DSCP, flow label, application policy, signal quality, cost, etc. Multilink selections are coordinated in both the outbound and inbound directions based on source/target underlying interface pairs.¶

Multinet

an OAL intermediate node's manner of spanning multiple diverse IP Internetwork and/or private enterprise network "segments" at the OAL layer below IP. Through intermediate node concatenation of SRT bridged network segments, multiple diverse Internetworks (such as the global public IPv4 and IPv6 Internets) can serve as transit segments in a bridged path for forwarding IP packets end-to-end. This bridging capability provide benefits such as supporting IPv4/IPv6 transition and coexistence, joining multiple diverse operator networks into a cooperative single service network, etc.¶

Multihop

an iterative relaying of IP packets between Client's over an OMNI underlying interface technology (such as omnidirectional wireless) without support of fixed infrastructure. Multihop services entail Client-to-Client relaying within a Mobile/Vehicular Ad-hoc Network (MANET/VANET) for Vehicle-to-Vehicle (V2V) communications and/or for Vehicle-to-Infrastructure (V2I) "range extension" where Clients within range of communications infrastructure elements provide forwarding services for other Clients.¶

L2

The second layer in the OSI network model. Also known as "layer-2", "link-layer", "sub-IP layer", "data link layer", etc.¶

L3

The third layer in the OSI network model. Also known as "layer-3", "network-layer", "IP layer", etc.¶

underlying interface

a *NET interface over which an OMNI interface is configured. The OMNI interface is seen as a L3 interface by the IP layer, and each underlying interface is seen as a L2 interface by the OMNI interface. The underlying interface either connects directly to the physical communications media or coordinates with another node where the physical media is hosted.¶

Mobility Service Identification (MSID)

Each Proxy/Server is assigned a unique 32-bit Identification (MSID) (see: Section 8). IDs are assigned according to MS-specific guidelines (e.g., see: [I-D.templin-6man-aero]).¶

Safety-Based Multilink (SBM)

A means for ensuring fault tolerance through redundancy by connecting multiple affiliated OMNI interfaces to independent routing topologies (i.e., multiple independent OMNI links).¶

Performance Based Multilink (PBM)

A means for selecting one or more underlying interface(s) for packet transmission and reception within a single OMNI interface.¶

OMNI Domain

The set of all SBM/PBM OMNI links that collectively provides services for a common set of MSPs. Each OMNI domain consists of a set of affiliated OMNI links that all configure the same ::/48 ULA prefix with a unique 16-bit Subnet ID as discussed in Section 9.¶

Multilink Forwarding Information Base (MFIB)

A forwarding table on each OMNI source, destination and intermediate node that includes Multilink Forwarding Vectors (MFV) with both next hop forwarding instructions and context for reconstructing compressed headers for specific underlying interface pairs used to communicate with peers. See: [I-D.templin-6man-aero] for further discussion.¶

Multilink Forwarding Vector (MFV)

An MFIB entry that includes soft state for each underlying interface pairwise communication session between peers. MFVs are identified by both a next-hop and previous-hop MFV Index (MFVI), with the next-hop established based on an IPv6 ND solicitation and the previous hop established based on the solicited IPv6 ND advertisement response. See: [I-D.templin-6man-aero] for further discussion.¶

Multilink Forwarding Vector Index (MVFI)

A 4 octet value selected by an OMNI node when it creates an MFV, then advertised to either a next-hop or previous-hop. OMNI intermediate nodes assign two distinct MFVIs for each MFV and advertise one to the next-hop and the other to the previous-hop. OMNI end systems assign and advertise a single MFVI. See: [I-D.templin-6man-aero] for further discussion.¶

3. Requirements

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119][RFC8174] when, and only when, they appear in all capitals, as shown here.¶

An implementation is not required to internally use the architectural constructs described here so long as its external behavior is consistent with that described in this document.¶

4. Overlay Multilink Network (OMNI) Interface Model

An OMNI interface is a virtual interface configured over one or more underlying interfaces, which may be physical (e.g., an aeronautical radio link, etc.) or virtual (e.g., an Internet or higher-layer "tunnel"). The OMNI interface architectural layering model is the same as in [RFC5558][RFC7847], and augmented as shown in Figure 1. The IP layer therefore sees the OMNI interface as a single L3 interface nexus for multiple underlying interfaces that appear as L2 communication channels in the architecture.¶

                                  +----------------------------+
                                  |    Upper Layer Protocol    |
           Session-to-IP    +---->|                            |
           Address Binding  |     +----------------------------+
                            +---->|           IP (L3)          |
           IP Address       +---->|                            |
           Binding          |     +----------------------------+
                            +---->|       OMNI Interface       |
           Logical-to-      +---->|   (OMNI Adaptation Layer)  |
           Physical         |     +----------------------------+
           Interface        +---->|  L2  |  L2  |       |  L2  |
           Binding                |(IF#1)|(IF#2)| ..... |(IF#n)|
                                  +------+------+       +------+
                                  |  L1  |  L1  |       |  L1  |
                                  |      |      |       |      |
                                  +------+------+       +------+

Each underlying interface provides an L2/L1 abstraction according to one of the following models:¶

• INET interfaces connect to an INET either natively or through one or several IPv4 Network Address Translators (NATs). Native INET interfaces have global IP addresses that are reachable from any INET correspondent. NATed INET interfaces typically have private IP addresses and connect to a private network behind one or more NATs that provide INET access.¶
• ANET interfaces connect to a protected and secured ANET that is separated from the open INET by a Proxy/Server. The ANET interface may be either on the same L2 link segment as the Proxy/Server, or separated from the Proxy/Server by multiple IP hops. (Note that NATs may appear internally within an ANET and may require NAT traversal the same as for the INET case.)¶
• VPNed interfaces use security encapsulation over a *NET to a Proxy/Server acting as a Virtual Private Network (VPN) gateway. Other than the link-layer encapsulation format, VPNed interfaces behave the same as for Direct interfaces.¶
• Direct (aka "point-to-point") interfaces connect directly to a peer without crossing any *NET paths. An example is a line-of-sight link between a remote pilot and an unmanned aircraft.¶

The OMNI interface forwards original IP packets from the network layer (L3) using the OMNI Adaptation Layer (OAL) (see: Section 5) as an encapsulation and fragmentation sublayer service. This "OAL source" then further encapsulates the resulting OAL packets/fragments in *NET headers to create "carrier packets" for transmission over underlying interfaces (L2/L1). The target OMNI interface receives the carrier packets from underlying interfaces (L1/L2) and discards the *NET headers. If the resulting OAL packets/fragments are addressed to itself, the OMNI interface acts as an "OAL destination" and performs reassembly if necessary, discards the OAL encapsulation, and delivers the original IP packet to the network layer (L3). If the OAL fragments are addressed to another node, the OMNI interface instead acts as an "OAL intermediate node" by re-encapsulating in new *NET headers and forwarding the new carrier packets over an underlying interface without reassembling or discarding the OAL encapsulation. The OAL source and OAL destination are seen as "neighbors" on the OMNI link, while OAL intermediate nodes provide a virtual bridging service that joins the segments of a (multinet) Segment Routing Topology (SRT).¶

The OMNI interface can send/receive original IP packets to/from underlying interfaces while including/omitting various encapsulations including OAL, UDP, IP and L2. The network layer can also access the underlying interfaces directly while bypassing the OMNI interface entirely when necessary. This architectural flexibility may be beneficial for underlying interfaces (e.g., some aviation data links) for which encapsulation overhead may be a primary consideration. OMNI interfaces that send original IP packets directly over underlying interfaces without invoking the OAL can only reach peers located on the same OMNI link segment. Source Clients can instead use the OAL to coordinate with target Clients in the same or different OMNI link segments by sending initial carrier packets to a First-Hop Segment (FHS) Proxy/Server. The FHS Proxy/Sever then forwards the packets into the SRT spanning tree, which transports them to a Last-Hop Segment (LHS) Proxy/Server for the target Client.¶

Original IP packets sent directly over underlying interfaces are subject to the same path MTU related issues as for any Internetworking path, and do not include per-packet identifications that can be used for data origin verification and/or link-layer retransmissions. Original IP packets presented directly to an underlying interface that exceed the underlying network path MTU are dropped with an ordinary ICMPv6 Packet Too Big (PTB) message returned. These PTB messages are subject to loss [RFC2923] the same as for any non-OMNI IP interface.¶

The OMNI interface encapsulation/decapsulation layering possibilities are shown in Figure 2 below. Imaginary vertical lines drawn between the Network Layer and Underlying interfaces in the figure denote the encapsulation/decapsulation layering combinations possible. Common combinations include NULL (i.e., direct access to underlying interfaces with or without using the OMNI interface), IP/IP, IP/UDP/IP, IP/UDP/IP/L2, IP/OAL/UDP/IP, IP/OAL/UDP/L2, etc.¶

   +------------------------------------------------------------+
   |             Network Layer (Original IP packets)            |
   +--+---------------------------------------------------------+
      |         OMNI Interface (virtual sublayer nexus)         |
      +--------------------------+------------------------------+
                                 |      OAL Encaps/Decaps       |
                                 +------------------------------+
                                 |        OAL Frag/Reass        |
                    +------------+---------------+--------------+
                    | UDP Encaps/Decaps/Compress |
               +----+---+------------+--------+--+  +--------+
               | IP E/D |            | IP E/D |     | IP E/D |
           +---+------+-+----+    +--+---+----+     +----+---+--+
           |L2 E/D|   |L2 E/D|    |L2 E/D|               |L2 E/D|
   +-------+------+---+------+----+------+---------------+------+
   |                   Underlying Interfaces                    |
   +------------------------------------------------------------+

The OMNI/OAL model gives rise to a number of opportunities:¶

• Clients receive MNPs from the MS, and coordinate with the MS through IPv6 ND message exchanges with Proxy/Servers. Clients use the MNP to construct a unique Link-Local Address (MNP-LLA) through the algorithmic derivation specified in Section 8 and assign the LLA to the OMNI interface. Since MNP-LLAs are uniquely derived from an MNP, no Duplicate Address Detection (DAD) or Multicast Listener Discovery (MLD) messaging is necessary.¶
• since Temporary ULAs are statistically unique, they can be used without DAD until an MNP-LLA is obtained.¶
• underlying interfaces on the same L2 link segment as a Proxy/Server do not require any L3 addresses (i.e., not even link-local) in environments where communications are coordinated entirely over the OMNI interface.¶
• as underlying interface properties change (e.g., link quality, cost, availability, etc.), any active interface can be used to update the profiles of multiple additional interfaces in a single message. This allows for timely adaptation and service continuity under dynamically changing conditions.¶
• coordinating underlying interfaces in this way allows them to be represented in a unified MS profile with provisions for mobility and multilink operations.¶
• exposing a single virtual interface abstraction to the IPv6 layer allows for multilink operation (including QoS based link selection, packet replication, load balancing, etc.) at L2 while still permitting L3 traffic shaping based on, e.g., DSCP, flow label, etc.¶
• the OMNI interface allows multinet traversal over the SRT when communications across different administrative domain network segments are necessary. This mode of operation would not be possible via direct communications over the underlying interfaces themselves.¶
• the OAL supports lossless and adaptive path MTU mitigations not available for communications directly over the underlying interfaces themselves. The OAL supports "packing" of multiple IP payload packets within a single OAL "super-packet".¶
• the OAL applies per-packet identification values that allow for link-layer reliability and data origin authentication.¶
• L3 sees the OMNI interface as a point of connection to the OMNI link; if there are multiple OMNI links (i.e., multiple MS's), L3 will see multiple OMNI interfaces.¶
• Multiple independent OMNI interfaces can be used for increased fault tolerance through Safety-Based Multilink (SBM), with Performance-Based Multilink (PBM) applied within each interface.¶

Note that even when the OMNI virtual interface is present, applications can still access underlying interfaces either through the network protocol stack using an Internet socket or directly using a raw socket. This allows for intra-network (or point-to-point) communications without invoking the OMNI interface and/or OAL. For example, when an IPv6 OMNI interface is configured over an underlying IPv4 interface, applications can still invoke IPv4 intra-network communications as long as the communicating endpoints are not subject to mobility dynamics.¶

Figure 3 depicts the architectural model for a source Client with an attached EUN connecting to the OMNI link via multiple independent *NETs. The Client's OMNI interface sends IPv6 ND messages over available underlying interfaces to FHS Proxy/Servers using any necessary *NET encapsulations. The IPv6 ND messages traverse the *NETs until they reach an FHS Proxy/Server (FHS#1, FHS#2, ..., FHS#n), which returns an IPv6 ND message response and/or forwards a proxyed version of the message over the SRT to an LHS Proxy/Server near the target Client (LHS#1, LHS#2, ..., LHS#m). The Hop Limit in IPv6 ND messages is not decremented due to encapsulation; hence, the source and target Client OMNI interfaces appear to be attached to a common link.¶

                        +--------------+        (:::)-.
                        |Source Client |<-->.-(::EUN:::)
                        +--------------+      `-(::::)-'
                        |OMNI interface|
                        +----+----+----+
               +--------|IF#1|IF#2|IF#n|------ +
              /         +----+----+----+        \
             /                 |                 \
            /                  |                  \
           v                   v                   v
        (:::)-.              (:::)-.              (:::)-.
   .-(::*NET:::)        .-(::*NET:::)        .-(::*NET:::)
     `-(::::)-'           `-(::::)-'           `-(::::)-'
      +-----+              +-----+              +-----+
 ...  |FHS#1|  .........   |FHS#2|   .........  |FHS#n|  ...
.     +--|--+              +--|--+              +--|--+     .
.        |                    |                    |
.        \                    v                    /        .
.         \                                       /         .
.           v                 (:::)-.           v            .
.                        .-(::::::::)                       .
.                    .-(::: Segment :::)-.                  .
.                  (:::::   Routing   ::::)                 .
.                     `-(:: Topology ::)-'                  .
.                         `-(:::::::-'                      .
.                  /          |          \                  .
.                 /           |           \                 .
.                v            v            v
.     +-----+              +-----+              +-----+     .
 ...  |LHS#1|  .........   |LHS#2|   .........  |LHS#m|  ...
      +--|--+              +--|--+              +--|--+
          \                   |                    /
           v                  v                   v
                    <-- Target Clients -->

After the initial IPv6 ND message exchange, the source Client (and/or any nodes on its attached EUNs) can send packets to the target Client over the OMNI interface. OMNI interface multilink services will forward the packets via FHS Proxy/Servers for the correct underlying *NETs. The FHS Proxy/Server then forwards them over the SRT which delivers them to an LHS Proxy/Server, and the LHS Proxy/Server in turn forwards the packets to the target Client. (Note that when the source and target Client are on the same SRT segment, the FHS and LHS Proxy/Servers may be one and the same.)¶

Clients select a Hub Proxy/Server (not shown in the figure), which will often be one of their FHS Proxy/Servers but could also be any Proxy/Server on the OMNI link. Clients then register all of their underlying interfaces with the Hub Proxy/Server via the FHS Proxy/Server in a pure proxy role. The Hub Proxy/Server then provides a designated router service for the Client, and the Client can quickly migrate to a new Hub Proxy/Server if the first becomes unresponsive.¶

Clients therefore use Proxy/Servers as gateways into the SRT to reach OMNI link correspondents via a spanning tree established in a manner outside the scope of this document. Proxy/Servers forward critical MS control messages via the secured spanning tree and forward other messages via the unsecured spanning tree (see Security Considerations). When route optimization is applied as discussed in [I-D.templin-6man-aero], Clients can instead forward directly to an SRT intermediate system themselves (or directly to correspondents in the same SRT segment) to reduce Proxy/Server load.¶

5. OMNI Interface Maximum Transmission Unit (MTU)

The OMNI interface observes the link nature of tunnels, including the Maximum Transmission Unit (MTU), Maximum Reassembly Unit (MRU) and the role of fragmentation and reassembly [I-D.ietf-intarea-tunnels]. The OMNI interface is configured over one or more underlying interfaces as discussed in Section 4, where the interfaces (and their associated *NET paths) may have diverse MTUs. OMNI interface considerations for accommodating original IP packets of various sizes are discussed in the following sections.¶

IPv6 underlying interfaces are REQUIRED to configure a minimum MTU of 1280 bytes and a minimum MRU of 1500 bytes [RFC8200]. Therefore, the minimum IPv6 path MTU is 1280 bytes since routers on the path are not permitted to perform network fragmentation even though the destination is required to reassemble more. The network therefore MUST forward original IP packets of at least 1280 bytes without generating an IPv6 Path MTU Discovery (PMTUD) Packet Too Big (PTB) message [RFC8201]. (While the source can apply "source fragmentation" for locally-generated IPv6 packets up to 1500 bytes and larger still if it knows the destination configures a larger MRU, this does not affect the minimum IPv6 path MTU.)¶

IPv4 underlying interfaces are REQUIRED to configure a minimum MTU of 68 bytes [RFC0791] and a minimum MRU of 576 bytes [RFC0791][RFC1122]. Therefore, when the Don't Fragment (DF) bit in the IPv4 header is set to 0 the minimum IPv4 path MTU is 576 bytes since routers on the path support network fragmentation and the destination is required to reassemble at least that much. The OMNI interface therefore MUST set DF to 0 in the IPv4 encapsulation headers of carrier packets that are no larger than 576 bytes, and SHOULD set DF to 1 in larger carrier packets unless it has a way to determine the encapsulation destination MRU and has carefully considered the issues discussed in Section 6.10.¶

The OMNI interface configures an MTU and MRU of 9180 bytes [RFC2492]; the size is therefore not a reflection of the underlying interface or *NET path MTUs, but rather determines the largest original IP packet the OAL (and/or underlying interface) can forward or reassemble. For each OAL destination (i.e., for each OMNI link neighbor), the OAL source may discover "hard" or "soft" Reassembly Limit values smaller than the MRU based on receipt of IPv6 ND messages with OMNI Reassembly Limit sub-options (see: Section 12.2.10). The OMNI interface employs the OAL as an encapsulation sublayer service to transform original IP packets into OAL packets/fragments, and the OAL in turn uses *NET encapsulation to forward carrier packets over the underlying interfaces (see: Section 6).¶

6. The OMNI Adaptation Layer (OAL)

When an OMNI interface forwards an original IP packet from the network layer for transmission over one or more underlying interfaces, the OMNI Adaptation Layer (OAL) acting as the OAL source drops the packet and returns a PTB message if the packet exceeds the MRU and/or the hard Reassembly Limit for the intended OAL destination. Otherwise, the OAL source applies encapsulation to form OAL packets subject to fragmentation producing OAL fragments suitable for *NET encapsulation and transmission as carrier packets over underlying interfaces as described in Section 6.1.¶

These carrier packets travel over one or more underlying networks spanned by OAL intermediate nodes in the SRT, which re-encapsulate by removing the *NET headers of the first underlying network and appending *NET headers appropriate for the next underlying network in succession. (This process supports the multinet concatenation capability needed for joining multiple diverse networks.) After re-encapsulation by zero or more OAL intermediate nodes, the carrier packets arrive at the OAL destination.¶

When the OAL destination receives the carrier packets, it discards the *NET headers and reassembles the resulting OAL fragments into an OAL packet as described in Section 6.3. The OAL destination then decapsulates the OAL packet to obtain the original IP packet, which it then delivers to the network layer. The OAL source may be either the source Client or its FHS Proxy/Server, while the OAL destination may be either the LHS Proxy/Server or the target Client. Proxy/Servers (and other SRT infrastructure node types such as those discussed in [I-D.templin-6man-aero]) may also serve as OAL intermediate nodes.¶

The OAL presents an OMNI sublayer abstraction similar to ATM Adaptation Layer 5 (AAL5). Unlike AAL5 which performs segmentation and reassembly with fixed-length 53 octet cells over ATM networks, however, the OAL uses IPv6 encapsulation, fragmentation and reassembly with larger variable-length cells over heterogeneous underlying networks. Detailed operations of the OAL are specified in the following sections.¶

   +----------+-----+-----+-----+-----+-----+-----+----+
   |OAL Header|         Original IP packet        |Csum|
   +----------+-----+-----+-----+-----+-----+-----+----+

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |                                                               |
   +                     OAL Source Address                        +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |                                                               |
   +                  OAL Destination Address                      +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       OAL Payload Length      |     zero      |  Next Header  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         Identification                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     +----------+----------------+
     |OAL Header|     Frag #0    |
     +----------+----------------+
         +----------+----------------+
         |OAL Header|     Frag #1    |
         +----------+----------------+
             +----------+----------------+
             |OAL Header|     Frag #2    |
             +----------+----------------+
                               ....
                 +----------+----------------+----+
                 |OAL Header|   Frag #(N-1)  |Csum|
                 +----------+----------------+----+
     a) OAL fragmentation (Csum in final fragment)


     +----------+-----+-----+-----+-----+-----+----+
     |OAL Header|      Original IP packet     |Csum|
     +----------+-----+-----+-----+-----+-----+----+
     b) An OAL atomic fragment


     +--------+----------+----------------+
     |*NET Hdr|OAL Header|     Frag #i    |
     +--------+----------+----------------+
     c) OAL carrier packet after *NET encapsulation

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Type=0 | Traffic Class |           Flow Label                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Next Header  | Hop Limit |I|M|      Identification (0-1)     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Identification (2-3)    |           MFVI (0-1)          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            MFVI (2-3)         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Type=1 | Ordinal |I|M|    Fragment Offset      |     Id(0)     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             Identification (1-3)              |    MFVI(0)    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  MFVI (1-3)                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  *NET headers (previous hop)  |   |    *NET headers (next hop)    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Original OAL/OCH Hdr      |   |   Encapsulation OAL/OCH Hdr   |
   |        Id=0x12345678          |   |         Id=0x98765432         |
   |       MFVI=0x2376a7b5         |   |        MFVI=0xacdebf12        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                               |   |      Original OAL/OCH Hdr     |
   |                               |   |         Id=0x12345678         |
   |      Carrier packet data      |   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                               |   |                               |
   |                               |   |                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |      Carrier packet data      |
   |     Original OAL Checksum     |   |                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |                               |
       Original Carrier packet         +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
          from OAL source              |     Original OAL Checksum     |
                                       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                       |   Encapsulation OAL Checksum  |
                                       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                                      Carrier packet following OAL ingress
                                       encapsulation before fragmentation

    Send Sequence Variables (current, previous and pending)

      SND.NXT - send next
      SND.WND - send window
      ISS     - initial send sequence number

    Receive Sequence Variables (current and previous)

      RCV.NXT - receive next
      RCV.WND - receive window
      IRS     - initial receive sequence number

                <------- Original IP packets ------->
                +-----+-----+
                | iHa | iDa |
                +-----+-----+
                      |
                      |     +-----+-----+
                      |     | iHb | iDb |
                      |     +-----+-----+
                      |           |
                      |           |     +-----+-----+
                      |           |     | iHc | iDc |
                      |           |     +-----+-----+
                      |           |           |
                      v           v           v
     +----------+-----+-----+-----+-----+-----+-----+----+
     |  OAL Hdr | iHa | iDa | iHb | iDb | iHc | iDc |Csum|
     +----------+-----+-----+-----+-----+-----+-----+----+
     <--- OAL "Super-Packet" with single OAL Hdr/Csum --->

7. Frame Format

When the OMNI interface forwards original IP packets from the network layer it first invokes the OAL to create OAL packets/fragments if necessary, then includes any *NET encapsulations and finally engages the native frame format of the underlying interface. For example, for Ethernet-compatible interfaces the frame format is specified in [RFC2464], for aeronautical radio interfaces the frame format is specified in standards such as ICAO Doc 9776 (VDL Mode 2 Technical Manual), for various forms of tunnels the frame format is found in the appropriate tunneling specification, etc.¶

See Figure 2 for a map of the various *NET layering combinations possible. For any layering combination, the final layer (e.g., UDP, IP, Ethernet, etc.) must have an assigned number and frame format representation that is compatible with the selected underlying interface.¶

8. Link-Local Addresses (LLAs)

OMNI interfaces assign IPv6 Link-Local Addresses (LLAs) through pre-service administrative actions. Clients assign "MNP-LLAs" with interface identifiers that embed the Client's unique MNP, while Proxy/Servers assign "ADM-LLAs" that include an administrative ID guaranteed to be unique on the link. LLAs are configured as follows:¶

• IPv6 MNP-LLAs encode the most-significant 64 bits of a MNP within the least-significant 64 bits of the IPv6 link-local prefix fe80::/64, i.e., in the LLA "interface identifier" portion. The prefix length for the LLA is determined by adding 64 to the MNP prefix length. For example, for the MNP 2001:db8:1000:2000::/56 the corresponding MNP-LLA prefix is fe80::2001:db8:1000:2000/120. (The base MNP-LLA for each "/N" prefix sets the final 128-N bits to 0, but all MNP-LLAs that match the prefix are also accepted.) Non-MNP routes are also represented the same as for MNP-LLAs, but include a GUA prefix that is not properly covered by the MSP.¶
• IPv4-mapped MNP-LLAs are constructed as fe80::ffff:[IPv4], i.e., the interface identifier consists of 16 '0' bits, followed by 16 '1' bits, followed by a 32bit IPv4 address/prefix. The prefix length for the LLA is determined by adding 96 to the MNP prefix length. For example, the IPv4-mapped MNP-LLA for 192.0.2.0/24 is fe80::ffff:192.0.2.0/120, also written as fe80::ffff:c000:0200/120. (The base MNP-LLA for each "/N" prefix sets the final 128-N bits to 0, but all MNP-LLAs that match the prefix are also accepted.)¶
• ADM-LLAs are assigned to Proxy/Servers (and possibly other SRT infrastructure elements) and MUST be managed for uniqueness. The lower 32 bits of the LLA includes a unique integer "MSID" value between 0x00000001 and 0xfeffffff, e.g., as in fe80::1, fe80::2, fe80::3, etc., fe80::feffffff. The ADM-LLA prefix length is determined by adding 96 to the MSID prefix length. For example, if the prefix length for MSID 0x10012001 is 16 then the ADM-LLA prefix length is set to 112 and the LLA is written as fe80::1001:2001/112. The "zero" address for each ADM-LLA prefix is the Subnet-Router anycast address for that prefix [RFC4291]; for example, the Subnet-Router anycast address for fe80::1001:2001/112 is simply fe80::1001:2000. The MSID range 0xff000000 through 0xffffffff is reserved for future use.¶

Since the prefix 0000::/8 is "Reserved by the IETF" [RFC4291], no MNPs can be allocated from that block ensuring that there is no possibility for overlap between the different MNP- and ADM-LLA constructs discussed above.¶

Since MNP-LLAs are based on the distribution of administratively assured unique MNPs, and since ADM-LLAs are guaranteed unique through administrative assignment, OMNI interfaces set the autoconfiguration variable DupAddrDetectTransmits to 0 [RFC4862].¶

Note: If future protocol extensions relax the 64-bit boundary in IPv6 addressing, the additional prefix bits of an MNP could be encoded in bits 16 through 63 of the MNP-LLA. (The most-significant 64 bits would therefore still be in bits 64-127, and the remaining bits would appear in bits 16 through 48.) However, the analysis provided in [RFC7421] suggests that the 64-bit boundary will remain in the IPv6 architecture for the foreseeable future.¶

Note: Even though this document honors the 64-bit boundary in IPv6 addressing, it specifies prefix lengths longer than /64 for routing purposes. This effectively extends IPv6 routing determination into the interface identifier portion of the IPv6 address, but it does not redefine the 64-bit boundary. Modern routing protocol implementations honor IPv6 prefixes of all lengths, up to and including /128.¶

9. Unique-Local Addresses (ULAs)

OMNI domains use IPv6 Unique-Local Addresses (ULAs) as the source and destination addresses in OAL packet IPv6 encapsulation headers. ULAs are only routable within the scope of a an OMNI domain, and are derived from the IPv6 Unique Local Address prefix fc00::/7 followed by the L bit set to 1 (i.e., as fd00::/8) followed by a 40-bit pseudo-random Global ID to produce the prefix [ULA]::/48, which is then followed by a 16-bit Subnet ID then finally followed by a 64 bit Interface ID as specified in Section 3 of [RFC4193]. All nodes in the same OMNI domain configure the same 40-bit Global ID as the OMNI domain identifier. The statistic uniqueness of the 40-bit pseudo-random Global ID allows different OMNI domains to be joined together in the future without requiring renumbering.¶

Each OMNI link instance is identified by a 16-bit Subnet ID value between 0x0000 and 0xfeff in bits 48-63 of [ULA]::/48. The Subnet ID values 0xff00 through 0xfffe are reserved for future use, while 0xffff denotes the presence of a Temporary ULA (see below). For example, OMNI ULAs associated with instance 0 are configured from the prefix [ULA]:0000::/64, instance 1 from [ULA]:0001::/64, instance 2 from [ULA]:0002::/64, etc. ULAs and their associated prefix lengths are configured in correspondence with LLAs through stateless prefix translation where "MNP-ULAs" are assigned in correspondence to MNP-LLAs and "ADM-ULAs" are assigned in correspondence to ADM-LLAs. For example, for OMNI link instance [ULA]:1010::/64:¶

• the MNP-ULA corresponding to the MNP-LLA fe80::2001:db8:1:2 with a 56-bit MNP length is derived by copying the lower 64 bits of the LLA into the lower 64 bits of the ULA as [ULA]:1010:2001:db8:1:2/120 (where, the ULA prefix length becomes 64 plus the IPv6 MNP length).¶
• the MNP-ULA corresponding to fe80::ffff:192.0.2.0 with a 28-bit MNP length is derived by simply writing the LLA interface ID into the lower 64 bits as [ULA]:1010:0:ffff:192.0.2.0/124 (where, the ULA prefix length is 64 plus 32 plus the IPv4 MNP length).¶
• the ADM-ULA corresponding to fe80::1000/112 is simply [ULA]:1010::1000/112.¶
• the ADM-ULA corresponding to fe80::/128 is simply [ULA]:1010::/128.¶
• etc.¶

The ULA presents an IPv6 address format that is routable within the OMNI routing system and can be used to convey link-scoped IPv6 ND messages across multiple hops using IPv6 encapsulation [RFC2473]. The OMNI link extends across one or more underling Internetworks to include all Proxy/Servers. All Clients are also considered to be connected to the OMNI link, however unnecessary encapsulations are omitted whenever possible to conserve bandwidth (see: Section 14).¶

Temporary ULAs are constructed per [RFC8981] based on the prefix [ULA]:ffff::/64 and used by Clients when they have no other addresses. Temporary ULAs can be used for Client-to-Client communications outside the context of any supporting OMNI link infrastructure, and can also be used as an initial address while the Client is in the process of procuring an MNP. Temporary ULAs are not routable within the OMNI routing system, and are therefore useful only for OMNI link "edge" communications. Temporary ULAs employ optimistic DAD principles [RFC4429] since they are probabilistically unique.¶

Each OMNI link may be subdivided into SRT segments that often correspond to different administrative domains or physical partitions. OMNI nodes can use Segment Routing [RFC8402] to support efficient forwarding to destinations located in other OMNI link segments. A full discussion of Segment Routing over the OMNI link appears in [I-D.templin-6man-aero].¶

Note: IPv6 ULAs taken from the prefix fc00::/7 followed by the L bit set to 0 (i.e., as fc00::/8) are never used for OMNI OAL addressing, however the range could be used for MSP/MNP addressing under certain limiting conditions (see: Section 10).¶

10. Global Unicast Addresses (GUAs)

OMNI domains use IP Global Unicast Address (GUA) prefixes [RFC4291] as Mobility Service Prefixes (MSPs) from which Mobile Network Prefixes (MNP) are delegated to Clients. Fixed correspondent node networks reachable from the OMNI domain are represented by non-MNP GUA prefixes that are not derived from the MSP, but are treated in all other ways the same as for MNPs.¶

For IPv6, GUA MSPs are assigned by IANA [IPV6-GUA] and/or an associated regional assigned numbers authority such that the OMNI domain can be interconnected to the global IPv6 Internet without causing inconsistencies in the routing system. An OMNI domain could instead use ULAs with the 'L' bit set to 0 (i.e., from the prefix fc00::/8)[RFC4193], however this would require IPv6 NAT if the domain were ever connected to the global IPv6 Internet.¶

For IPv4, GUA MSPs are assigned by IANA [IPV4-GUA] and/or an associated regional assigned numbers authority such that the OMNI domain can be interconnected to the global IPv4 Internet without causing routing inconsistencies. An OMNI domain could instead use private IPv4 prefixes (e.g., 10.0.0.0/8, etc.) [RFC3330], however this would require IPv4 NAT if the domain were ever connected to the global IPv4 Internet. OMNI interfaces advertise IPv4 MSPs into IPv6 routing systems as IPv4-mapped IPv6 prefixes [RFC4291] (e.g., the IPv6 prefix for the IPv4 MSP 192.0.2.0/24 is ::ffff:192.0.2.0/120).¶

OMNI interfaces assign the IPv4 anycast address TBD3, and IPv4 routers that configure OMNI interfaces advertise the prefix TBD3/N into the routing system of other networks (see: IANA Considerations). OMNI interfaces also configure global IPv6 anycast addresses formed according to [RFC3056] as:¶

2002:TBD3[32]:MNP[64]:Link_ID[16]¶

where TBD3[32] is the 32 bit IPv4 anycast address, MNP[64] encodes an MSP zero-padded to 64 bits (if necessary) and Link_ID[16] encodes a 16 bit value between 0 and 0xfffe that identifies a specific OMNI link within an OMNI domain (the Link_ID value 0xffff is an OMNI link "anycast" value configured by all OMNI interfaces within the same domain). For example, the OMNI IPv6 anycast address for MSP 2001:db8::/32 is 2002:TBD3[32]:2001:db8:0:0:Link_ID[16], the OMNI IPv6 anycast address for MSP 192.0.2.0/24 is 2002:TBD3[32]:0000:ffff:c000:0200:Link_ID[16], etc.).¶

OMNI interfaces assign OMNI IPv6 anycast addresses, and IPv6 routers that configure OMNI interfaces advertise the corresponding prefixes into the routing system of other networks. An OMNI IPv6 anycast prefix is formed the same as for any IPv6 prefix; for example, the prefix 2002:TBD3[32]:2001:db8::/80 matches all OMNI IPv6 anycast addresses covered by the prefix. By advertising OMNI IPv6 anycast prefixes in this way, OMNI Clients can locate and associate with the OMNI domain and/or a specific link within the OMNI domain that services the MSP of interest.¶

OMNI interfaces use OMNI IPv6 and IPv4 anycast addresses to support Service Discovery in the spirit of [RFC7094], i.e., the addresses are not intended for use in long-term transport protocol sessions. Specific applications for OMNI IPv6 and IPv4 anycast addresses are discussed throughout the document as well as in [I-D.templin-6man-aero].¶

11. Node Identification

OMNI Clients and Proxy/Servers that connect over open Internetworks include a unique node identification value for themselves in the OMNI options of their IPv6 ND messages (see: Section 12.2.12). An example identification value alternative is the Host Identity Tag (HIT) as specified in [RFC7401], while Hierarchical HITs (HHITs) [I-D.ietf-drip-rid] may be more appropriate for certain domains such as the Unmanned (Air) Traffic Management (UTM) service for Unmanned Air Systems (UAS). Another example is the Universally Unique IDentifier (UUID) [RFC4122] which can be self-generated by a node without supporting infrastructure with very low probability of collision.¶

When a Client is truly outside the context of any infrastructure, it may have no MNP information at all. In that case, the Client can use an IPv6 temporary ULA or (H)HIT as an IPv6 source/destination address for sustained communications in Vehicle-to-Vehicle (V2V) and (multihop) Vehicle-to-Infrastructure (V2I) scenarios. The Client can also propagate the ULA/(H)HIT into the multihop routing tables of (collective) Mobile/Vehicular Ad-hoc Networks (MANETs/VANETs) using only the vehicles themselves as communications relays.¶

When a Client connects via a protected-spectrum ANET, an alternate form of node identification (e.g., MAC address, serial number, airframe identification value, VIN, etc.) embedded in an LLA/ULA may be sufficient. The Client can then include OMNI "Node Identification" sub-options (see: Section 12.2.12) in IPv6 ND messages should the need to transmit identification information over the network arise.¶

12. Address Mapping - Unicast

OMNI interfaces maintain a neighbor cache for tracking per-neighbor state and use the link-local address format specified in Section 8. IPv6 Neighbor Discovery (ND) [RFC4861] messages sent over OMNI interfaces without encapsulation observe the native underlying interface Source/Target Link-Layer Address Option (S/TLLAO) format (e.g., for Ethernet the S/TLLAO is specified in [RFC2464]). IPv6 ND messages sent over OMNI interfaces using encapsulation do not include S/TLLAOs, but instead include a new option type that encodes encapsulation addresses, interface attributes and other OMNI link information. Hence, this document does not define an S/TLLAO format but instead defines a new option type termed the "OMNI option" designed for these purposes. (Note that OMNI interface IPv6 ND messages sent without encapsulation may include both OMNI options and S/TLLAOs, but the information conveyed in each is mutually exclusive.)¶

OMNI interfaces prepare IPv6 ND messages that include one or more OMNI options (and any other IPv6 ND options) then completely populate all option information. If the OMNI interface includes an authentication signature, it sets the IPv6 ND message Checksum field to 0 and calculates the authentication signature over the length of the entire OAL packet or super-packet (beginning with a pseudo-header of the IPv6 ND message IPv6 header up to but not including the trailing OAL Checksum field) but does not calculate/include the IPv6 ND message checksum itself. Otherwise, the OMNI interface calculates the standard IPv6 ND message checksum over the entire OAL packet or super-packet and writes the value in the Checksum field noting that optimized implementations can verify both the OAL and IPv6 ND message checksums in a single pass over the message data. OMNI interfaces verify authentication and/or integrity of each IPv6 ND message received according to the specific check(s) included, and process the message further only following verification.¶

OMNI interface Clients such as aircraft typically have multiple wireless data link types (e.g. satellite-based, cellular, terrestrial, air-to-air directional, etc.) with diverse performance, cost and availability properties. The OMNI interface would therefore appear to have multiple L2 connections, and may include information for multiple underlying interfaces in a single IPv6 ND message exchange. OMNI interfaces manage their dynamically-changing multilink profiles by including OMNI options in IPv6 ND messages as discussed in the following subsections.¶

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |      Type     |     Length    |    Preflen    |    Reserved   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Sequence Number                        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Acknowledgment Number                     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S|A|R|O|P|     |                                               |
     |Y|C|S|P|N| Res |                   Window                      |
     |N|K|T|T|G|     |                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                          Sub-Options                          ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
     |     Type      |     Length    | Sub-Options ...
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
     | Sub-Type|      Sub-length     | Sub-Option Data ...
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

      0
      0 1 2 3 4 5 6 7
     +-+-+-+-+-+-+-+-+
     | S-Type=0|x|x|x|
     +-+-+-+-+-+-+-+-+

      0                   1                   2
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
     | S-Type=1|    Sub-length=N     | N padding octets ...
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=2|    Sub-length=N     |    omIndex    |     omType    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |  Provider ID  |  Link | Resvd | FMT |   SRT   |               ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+               ~
     ~                  LHS Proxy/Server MSID/INADDR                 ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   Old Hub Proxy/Server MSID                   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   Old FHS Proxy/Server MSID                   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=3|    Sub-length=N     |Job|  A  |  B  |               ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+               ~
     ~        Multilink Forwarding Vector Index (MFVI) List          ~
     ~               (5 consecutive 4-octet MFVIs)                   ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     ~           Tunnel Window Synchronization Parameters            ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |FHS Cli omIndex|     omType    |  Provider ID  |  Link | Resvd |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | FMT |   SRT   |                                               ~
     +-+-+-+-+-+-+-+-+                                               ~
     ~                 FHS Proxy/Server MSID/INADDR                  ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     ~                    FHS Bridge MSID/INADDR                     ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |LHS Cli omIndex|     omType    |  Provider ID  |  Link | Resvd |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | FMT |   SRT   |                                               ~
     +-+-+-+-+-+-+-+-+                                               ~
     ~                 LHS Proxy/Server MSID/INADDR                  ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     ~                     LHS Bridge MSID/INADDR                    ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=4|    Sub-length=N     |    omIndex    |   TS Format   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     ~                                                               ~
     ~                RFC 6088 Format Traffic Selector               ~
     ~                                                               ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=5|    Sub-length=N     |    Geo Type   |Geo Coordinates
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ...

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=6|    Sub-length=N     |    msg-type   |  id (octet 0) |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |   transaction-id (octets 1-2) |                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               |
     |                                                               |
     .                        DHCPv6 options                         .
     .                 (variable number and length)                  .
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=7|    Sub-length=N     |0| Packet Type |Version| RES.|1|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |           Reserved            |           Controls            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                Sender's Host Identity Tag (HIT)               |
     |                                                               |
     |                                                               |
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |               Receiver's Host Identity Tag (HIT)              |
     |                                                               |
     |                                                               |
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     /                        HIP Parameters                         /
     /                                                               /
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=8|    Sub-length=N     |PIM Ver| Type  |   Reserved    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     /                         PIM-SM Message                        /
     /                                                               /
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | S-Type=9|    Sub-length=N     |      Reassembly Limit       |H|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |          OAL First Fragment (As much of invoking packet       |
     +         as possible without causing the IPv6 ND message       +
     |                to exceed the minimum IPv6 MTU)                |
     +                                                               +

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S-Type=10|   Sub-Length = N    | Identification #1 (bits 0 -15)|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Identification #1 (bits 15-31)|    Bitmap #1 (bits 0 - 15)    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       Bitmap #1 (bits 16-31)  | Identification #2 (bits 0 -15)|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Identification #2 (bits 15-31)|    Bitmap #2 (bits 0 - 15)    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       Bitmap #2 (bits 16-31)  | Identification #3 (bits 0 -15)|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Identification #3 (bits 15-31)|    Bitmap #3 (bits 0 - 15)    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       Bitmap #3 (bits 16-31)  |             ...               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+             ...               +
     |                              ...                              |
     +                              ...                              +

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S-Type=11|    Sub-length=N    |     ID-Type    |               ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+               ~
     ~            Node Identification Value (N-1 octets)             ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         DUID-Type (2)         |      EN (high bits == 0)      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     EN (low bits = 45282)     |    ID-Type    |               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+               |
     .                    Node Identification Value                  .
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S-Type=12|    Sub-length=N    |                                ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-                                ~
     ~                    RFC4443 Error Message Body                 ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S-Type=13|    Sub-length=N    |                                ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-                                ~
     ~                         QUIC-TLS Message                      ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S-Type=30|     Sub-length=N    | Extension-Type|               ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+               ~
     ~                                                               ~
     ~                       Extension-Type Body                     ~
     ~                                                               ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S-Type=30|      Sub-length=N   |   Ext-Type=0  |   Header Type |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     ~                      Header Option Value                      ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S-Type=30|      Sub-length=N   |   Ext-Type=1  |  Trailer Type |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     ~                     Trailer Option Value                      ~
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

13. Address Mapping - Multicast

The multicast address mapping of the native underlying interface applies. The Client mobile router also serves as an IGMP/MLD Proxy for its EUNs and/or hosted applications per [RFC4605].¶

The Client uses Multicast Listener Discovery (MLDv2) [RFC3810] to coordinate with Proxy/Servers, and *NET L2 elements use MLD snooping [RFC4541]. The Client can also employ multicast routing protocols to coordinate with network-based multicast sources as specified in [I-D.templin-6man-aero].¶

Since the OMNI link model is NBMA, OMNI links support link-scoped multicast through iterative unicast transmissions to individual multicast group members (i.e., unicast/multicast emulation).¶

14. Multilink Conceptual Sending Algorithm

The Client's IPv6 layer selects the outbound OMNI interface according to SBM considerations when forwarding original IP packets from local or EUN applications to external correspondents. Each OMNI interface maintains a neighbor cache the same as for any IPv6 interface, but includes additional state for multilink coordination. Each Client OMNI interface maintains default routes via Proxy/Servers discovered as discussed in Section 15, and may configure more-specific routes discovered through means outside the scope of this specification.¶

For each original IP packet it forwards, the OMNI interface selects one or more source underlying interfaces based on PBM factors (e.g., traffic attributes, cost, performance, message size, etc.) and one or more target underlying interfaces for the neighbor based on Interface Attributes received in IPv6 ND messages (see: Section 12.2.3). Multilink forwarding may also direct packet replication across multiple underlying interface pairs for increased reliability at the expense of duplication. The set of all Interface Attributes and Traffic Selectors received in IPv6 ND messages determines the multilink forwarding profile for selecting target underlying interfaces.¶

When the OMNI interface sends an original IP packet over a selected source underlying interface, it first employs OAL encapsulation and fragmentation as discussed in Section 5, then performs *NET encapsulation as directed by the appropriate MFV. The OMNI interface also performs *NET encapsulation (following OAL encapsulation) when the nearest Proxy/Server is located multiple hops away as discussed in Section 15.2.¶

OMNI interface multilink service designers MUST observe the BCP guidance in Section 15 [RFC3819] in terms of implications for reordering when original IP packets from the same flow may be spread across multiple underlying interfaces having diverse properties.¶

15. Router Discovery and Prefix Registration

Clients interface with the MS by sending RS messages with OMNI options under the assumption that one or more Proxy/Server will process the message and respond. The RS message is received by a FHS Proxy/Server, which may in turn forward a proxyed copy of the RS to a Hub Proxy/Server located on the same or different SRT segment. The Hub Proxy/Server then returns an RA message either directly to the Client or via an FHS Proxy/Server acting as a proxy.¶

Clients and FHS Proxy/Servers include an authentication signature in their RS/RA exchanges when necessary; otherwise, they calculate and include a valid IPv6 ND message checksum (see: Section 12 and Appendix B). FHS and Hub Proxy/Server RS/RA message exchanges over the SRT secured spanning tree instead always include the checksum and omit the authentication signature. Clients and Proxy/Servers use the information included in RS/RA messages to establish NCE state and OMNI link autoconfiguration information as discussed in this section.¶

For each underlying interface, the Client sends RS messages with OMNI options to coordinate with a (potentially different) FHS Proxy/Server for each interface and a single Hub Proxy/Server. All Proxy/Servers are identified by their MSIDs and accept carrier packets addressed to their INADDRs; the Hub Proxy/Server may be chosen among any of the Client's FHS Proxy/Servers or may be any other Proxy/Server for the OMNI link. Example MSID/INADDR discovery methods are given in [RFC5214] and include data link login parameters, name service lookups, static configuration, a static "hosts" file, etc. In the absence of other information, the Client can resolve the DNS Fully-Qualified Domain Name (FQDN) "linkupnetworks.[domainname]" where "linkupnetworks" is a constant text string and "[domainname]" is a DNS suffix for the OMNI link (e.g., "example.com").¶

Clients configure OMNI interfaces that observe the properties discussed in previous sections. The OMNI interface and its underlying interfaces are said to be in either the "UP" or "DOWN" state according to administrative actions in conjunction with the interface connectivity status. An OMNI interface transitions to UP or DOWN through administrative action and/or through state transitions of the underlying interfaces. When a first underlying interface transitions to UP, the OMNI interface also transitions to UP. When all underlying interfaces transition to DOWN, the OMNI interface also transitions to DOWN.¶

When a Client OMNI interface transitions to UP, it sends RS messages to register its MNP and an initial set of underlying interfaces that are also UP. The Client sends additional RS messages to refresh lifetimes and to register/deregister underlying interfaces as they transition to UP or DOWN. The Client's OMNI interface sends initial RS messages over an UP underlying interface with its MNP-LLA as the source (or with the unspecified address (::) as the source if it does not yet have an MNP-LLA) and with destination set to link-scoped All-Routers multicast or the ADM-LLA of a specific Proxy/Server. The OMNI interface includes an OMNI option per Section 12 with a Preflen assertion, an Interface Attributes sub-option for the underlying interface and with any other necessary OMNI sub-options such as authentication, Reassembly Limits, etc.¶

The Client then calculates the authentication signature or checksum and prepares to forward the RS over the underlying interface using OAL encapsulation and fragmentation if necessary. If the Client uses OAL encapsulation for RS messages sent to an unsynchronized FHS Proxy/Server over an INET interface, the entire RS message must fit within a single carrier packet (i.e., an atomic fragment) so that the FHS Proxy/Server can verify the authentication signature without having to reassemble. The OMNI interface selects an Identification value (see: Section 6.6), sets the OAL source address to the ULA corresponding to the RS source (or a Temporary ULA or (H)HIT if the RS source is the unspecified address (::)), sets the OAL destination to an OMNI IPv6 anycast or ADM-ULA unicast address then performs fragmentation if necessary. When *NET encapsulation is used, the Client includes the discovered FHS Proxy/Server INADDR or an anycast address as the *NET destination then forwards the resulting carrier packet(s) into the *NET.¶

When an FHS Proxy/Server receives the carrier packets containing an RS it discards the *NET headers, reassembles if necessary, then verifies the authentication signature or checksum. The FHS Proxy/Server then caches the Window Synchronization parameters, Interface Attributes and any Traffic Selector sub-options in a NCE for the Client while also caching the *NET source address as Client INADDR information. If the RS destination address matches its own ADM-LLA, the FHS Proxy/Server then assumes the Hub role and acts as the sole entry point for injecting the Client's MNP into the MSE routing system (i.e., after performing any necessary MNP prefix delegation operations). The FHS/Hub Proxy/Server then prepares to return an RA message directly to the Client that includes Window Synchronization information and the Client's original Interface Attributes sub-option while writing its INET-facing interface information in the FMT/SRT and LHS Proxy/Server MSID/INADDR fields. If the FHS/Hub Proxy/Server's Client-facing interface is different than its INET-facing interface, it also includes an Interface Attributes sub-option with omIndex set to '0' while writing its Client-facing interface information in the LHS Proxy/Server MSID/INADDR fields to inform the Client of its unicast INADDR. The FHS/Hub Proxy/Server also includes an Origin Indication sub-option with the Client's cached *NET source INADDR (see: Section 12.2.15.1) then populates the RA with any information for the OMNI link including Cur Hop Limit, M and O flags, Router Lifetime, Reachable Time and Retrans Timer values. The FHS Proxy/Server next includes any necessary RA options such as PIOs with (A; L=0) that include the OMNI link MSPs [RFC8028], RIOs [RFC4191] with more-specific routes, etc. The FHS/Hub Proxy/Server then includes an authentication sub-option if necessary, sets the RA source address to its own ADM-LLA and destination address to the Client's MNP-LLA, then encapsulates the message in an OAL header with source set to its own ADM-ULA and destination set to the ULA source that appeared in the Client's RS message. The FHS/Hub Proxy/Server finally calculates the authentication signature or checksum, fragments if necessary, encapsulates each fragment in appropriate *NET headers and returns the resulting carrier packets to the Client over the same underlying interface the RS arrived on.¶

When an FHS Proxy/Server receives an RS with a valid authentication signature or checksum and with destination set to link-scoped All-Routers multicast, it can either assume the Hub role the same as above or act as a proxy and select the ADM-LLA of another Proxy/Server to serve as the Hub. When an FHS Proxy/Server assumes the proxy role or receives an RS with destination set to the ADM-LLA of another Proxy/Server, it proxys the message. The FHS Proxy/Server caches the Client's Window Synchronization, Interface Attributes and *NET INADDR information as above then writes its own INET-facing FMT/SRT and LHS Proxy/Server MSID/INADDR information into the appropriate Interface Attributes sub-option fields. The FHS Proxy/Server then sets the OAL header source to its own ADM-ULA and destination to the ADM-ULA of the Hub Proxy/Server then calculates and includes the checksum, fragments if necessary, encapsulates each fragment in appropriate *NET headers and sends the resulting carrier packets into the SRT secured spanning tree.¶

When the Hub Proxy/Server receives the carrier packets, it discards the *NET headers, reassembles if necessary to obtain the proxyed RS (i.e., one with an ADM-ULA source address) then caches any state (including Interface Attributes information and Traffic Selectors) in a NCE for the Client and performs any necessary prefix delegation and routing protocol injection. The Hub Proxy/Server then returns an RA that echoes the Client's (proxyed) Interface Attributes sub-option and with any RA parameters the same as specified above. The Hub Proxy/Server then sets the RA source address to its own ADM-LLA and destination address to the Client's MNP-LLA, then encapsulates the RA as an OAL packet with source set to its own ADM-ULA and destination set to the ADM-ULA of the FHS Proxy/Server that sent the RS. The Hub Proxy/server finally calculates the checksum, fragments if necessary, encapsulates each fragment in appropriate *NET headers and sends the resulting carrier packets into the secured spanning tree.¶

When the FHS Proxy/Server receives the carrier packets, it discards the *NET headers, reassembles to obtain the RA message, verifies the checksum then updates the OMNI inteface NCEs for both the Hub and Client. The FHS Proxy/Server then proxies the RA by changing the OAL source to its own ADM-ULA and the OAL destination to the MNP-ULA or temporary ULA of the Client, then sets the P flag in the RA flags field [RFC4389]. The FHS Proxy/Server next includes Window Synchronization parameters responsive to those in the Client's RS, an Interface Attributes sub-option with omIndex '0' and with its Client-facing INADDR information if necessary, an Origin Indication sub-option with the Client's cached INADDR and an authentication sub-option if necessary. The FHS Proxy/Server finally selects an Identification value per Section 6.6, calculates the authentication signature or checksum, fragments if necessary, encapsulates each fragment in appropriate *NET headers and returns the resulting carrier packets via the same underlying interface over which the RS was received.¶

When the Client receives the carrier packets, it discards the *NET headers, reassembles to obtain the RA message, verifies the authentication signature or checksum, then updates the OMNI interface NCEs for both the Hub and FHS Proxy/Server. If the Client has multiple underlying interfaces, it creates additional FHS Proxy/Server NCEs as necessary when it receives RAs over those interfaces (noting that multiple of the Client's underlying interfaces may be serviced by the same FHS Proxy/Server). For each underlying interface, the Client caches the (filled-out) Interface Attributes for its own omIndex and Origin Indication information that it received in an RA message over that interface so that it can include them in future NS/NA messages to provide neighbors with accurate LHS information. (If the message includes an Interface Attributes sub-option with omIndex '0', the Client also caches the INADDR information as the unicast address of the FHS Proxy//Server.) The Client then compares the Origin Indication INADDR information with its own underlying interface addresses to determine whether there may be NATs on the path to the FHS Proxy/Server; if the INADDRs differ, the Client is behind a NAT and must supply the Origin information in IPv6 ND message exchanges with prospective neighbors on the same SRT segment. The Client finally configures default routes and assigns the OMNI Subnet Router Anycast address corresponding to the MNP (e.g., 2001:db8:1:2::) to the OMNI interface.¶

Following the initial exchange, the FHS Proxy/Server MAY later send additional periodic and/or event-driven unsolicited RA messages per [RFC4861]. (The unsolicited RAs may be initiated either by the FHS Proxy/Server itself or by the Hub via the FHS as a proxy.) The Client then continuously manages its underlying interfaces according to their states as follows:¶

• When an underlying interface transitions to UP, the Client sends an RS over the underlying interface with an OMNI option with sub-options as specified above.¶
• When an underlying interface transitions to DOWN, the Client sends unsolicited NA messages over any UP underlying interface with an OMNI option containing Interface Attributes sub-options for the DOWN underlying interface with Link set to '0'. The Client sends isolated unsolicited NAs when reliability is not thought to be a concern (e.g., if redundant transmissions are sent on multiple underlying interfaces), or may instead set the PNG flag in the OMNI header to trigger a uNA reply.¶
• When the Router Lifetime for the Hub Proxy/Server nears expiration, the Client sends an RS over any underlying interface to receive a fresh RA from the Hub. If no RA messages are received over a first underlying interface (i.e., after retrying), the Client marks the underlying interface as DOWN and should attempt to contact the Hub Proxy/Server via a different underlying interface. If the Hub Proxy/Server is unresponsive over additional underlying interface, the Client selects a different FHS Proxy/Server and sends an RS message with destination set to the ADM-LLA of the FHS Proxy/Server which will then assume the Hub role.¶
• When all of a Client's underlying interfaces have transitioned to DOWN (or if the prefix registration lifetime expires), the Hub Proxy/Server withdraws the MNP the same as if it had received a message with a release indication.¶

The Client is responsible for retrying each RS exchange up to MAX_RTR_SOLICITATIONS times separated by RTR_SOLICITATION_INTERVAL seconds until an RA is received. If no RA is received over an UP underlying interface (i.e., even after attempting to contact alternate Proxy/Servers), the Client declares this underlying interface as DOWN.¶

The IPv6 layer sees the OMNI interface as an ordinary IPv6 interface. Therefore, when the IPv6 layer sends an RS message the OMNI interface returns an internally-generated RA message as though the message originated from an IPv6 router. The internally-generated RA message contains configuration information consistent with the information received from the RAs generated by the Hub Proxy/Server. Whether the OMNI interface IPv6 ND messaging process is initiated from the receipt of an RS message from the IPv6 layer or independently of the IPv6 layer is an implementation matter. Some implementations may elect to defer the OMNI interface internal RS/RA messaging process until an RS is received from the IPv6 layer, while others may elect to initiate the process proactively. Still other deployments may elect to administratively disable IPv6 layer RS/RA messaging over the OMNI interface, since the messages are not required to drive the OMNI interface internal RS/RA process. (Note that this same logic applies to IPv4 implementations that employ ICMP-based Router Discovery per [RFC1256].)¶

Note: The Router Lifetime value in RA messages indicates the time before which the Client must send another RS message over this underlying interface (e.g., 600 seconds), however that timescale may be significantly longer than the lifetime the MS has committed to retain the prefix registration (e.g., REACHABLETIME seconds). Proxy/Servers are therefore responsible for keeping MS state alive on a shorter timescale than the Client may be required to do on its own behalf.¶

Note: On multicast-capable underlying interfaces, Clients should send periodic unsolicited multicast NA messages and Proxy/Servers should send periodic unsolicited multicast RA messages as "beacons" that can be heard by other nodes on the link. If a node fails to receive a beacon after a timeout value specific to the link, it can initiate a unicast exchange to test reachability.¶

Note: If a single FHS Proxy/Server services multiple of a Client's underlying interfaces, Window Synchronization will initially be repeated for the RS/RA exchange over each underlying interface, i.e., until the Client discovers the many-to-one relationship.¶

Note: Although the Client's FHS Proxy/Server is a first-hop segment node from its own perspective, the Client stores the Proxy/Server's FMT/SRT/MSID/INADDR as last-hop segment (LHS) information. This allows both the Client and Hub Proxy/Server to supply the information to neighbors that will perceive it as LHS information on the return path to the Client.¶

Note: The Hub Proxy/Server injects Client MNP-ULAs into the routing system by simply creating a route-to-interface forwarding table entry for the MNP-ULA via the OMNI interface. The dynamic routing protocol will notice the new entry and advertise the MNP-ULA to its peers. If the Hub receives additional RS messages, it need not re-create the MNP-ULA forwarding table entry (nor disturb the dynamic routing protocol) if an entry is already present.¶

Note: If the Client's initial RS message includes an anycast *NET destination address, the FHS Proxy/Server returns the solicited RA using the same anycast address as the *NET source while including an Interface Attributes sub-option with omIndex '0' and its true unicast address in the INADDR. When the Client sends additional RS messages, it includes this FHS Proxy/Server unicast address as the *NET destination and the FHS Proxy/Server returns the solicited RA using the same unicast address as the *NET source. This will ensure that RS/RA exchanges are not impeded by any NATs on the path while avoiding long-term exposure of messages that use an anycast address as the source.¶

Note: The Origin Indication sub-option is included only by the FHS Proxy/Server and not by the Hub (unless the Hub is also serving as an FHS).¶

16. Secure Redirection

If the *NET link model is multiple access, the FHS Proxy/Server is responsible for assuring that address duplication cannot corrupt the neighbor caches of other nodes on the link. When the Client sends an RS message on a multiple access *NET link, the Proxy/Server verifies that the Client is authorized to use the address and responds with an RA (or forwards the RS to the Hub) only if the Client is authorized.¶

After verifying Client authorization and returning an RA, the Proxy/Server MAY return IPv6 ND Redirect messages to direct Clients located on the same *NET link to exchange packets directly without transiting the Proxy/Server. In that case, the Clients can exchange packets according to their unicast L2 addresses discovered from the Redirect message instead of using the dogleg path through the Proxy/Server. In some *NET links, however, such direct communications may be undesirable and continued use of the dogleg path through the Proxy/Server may provide better performance. In that case, the Proxy/Server can refrain from sending Redirects, and/or Clients can ignore them.¶

17. Proxy/Server Resilience

*NETs SHOULD deploy Proxy/Servers in Virtual Router Redundancy Protocol (VRRP) [RFC5798] configurations so that service continuity is maintained even if one or more Proxy/Servers fail. Using VRRP, the Client is unaware which of the (redundant) FHS Proxy/Servers is currently providing service, and any service discontinuity will be limited to the failover time supported by VRRP. Widely deployed public domain implementations of VRRP are available.¶

Proxy/Servers SHOULD use high availability clustering services so that multiple redundant systems can provide coordinated response to failures. As with VRRP, widely deployed public domain implementations of high availability clustering services are available. Note that special-purpose and expensive dedicated hardware is not necessary, and public domain implementations can be used even between lightweight virtual machines in cloud deployments.¶

18. Detecting and Responding to Proxy/Server Failures

In environments where fast recovery from Proxy/Server failure is required, FHS Proxy/Servers SHOULD use proactive Neighbor Unreachability Detection (NUD) in a manner that parallels Bidirectional Forwarding Detection (BFD) [RFC5880] to track Hub Proxy/Server reachability. FHS Proxy/Servers can then quickly detect and react to failures so that cached information is re-established through alternate paths. Proactive NUD control messaging is carried only over well-connected ground domain networks (i.e., and not low-end *NET links such as aeronautical radios) and can therefore be tuned for rapid response.¶

FHS Proxy/Servers perform proactive NUD for Hub Proxy/Servers for which there are currently active Clients on the *NET. If a Hub Proxy/Server fails, the FHS Proxy/Server can quickly inform Clients of the outage by sending multicast RA messages on the *NET interface. The FHS Proxy/Server sends RA messages to Clients via the *NET interface with source set to the ADM-LLA of the Hub, with destination address set to All-Nodes multicast (ff02::1) [RFC4291] and with Router Lifetime set to 0.¶

The FHS Proxy/Server SHOULD send MAX_FINAL_RTR_ADVERTISEMENTS RA messages separated by small delays [RFC4861]. Any Clients on the *NET interface that have been using the (now defunct) Hub Proxy/Server will receive the RA messages.¶

19. Transition Considerations

When a Client connects to an *NET link for the first time, it sends an RS message with an OMNI option. If the first hop router recognizes the option, it responds according to the appropriate FHS/Hub Proxy/Server role resulting in an RA message with an OMNI option returned to the Client. The Client then engages this FHS Proxy/Sever according to the OMNI link model specified above. If the first hop router is a legacy IPv6 router, however, it instead returns an RA message with no OMNI option and with a non-OMNI unicast source LLA as specified in [RFC4861]. In that case, the Client engages the *NET according to the legacy IPv6 link model and without the OMNI extensions specified in this document.¶

If the *NET link model is multiple access, there must be assurance that address duplication cannot corrupt the neighbor caches of other nodes on the link. When the Client sends an RS message on a multiple access *NET link with an LLA source address and an OMNI option, first hop routers that recognize the OMNI option ensure that the Client is authorized to use the address and return an RA with a non-zero Router Lifetime only if the Client is authorized. First hop routers that do not recognize the OMNI option instead return an RA that makes no statement about the Client's authorization to use the source address. In that case, the Client should perform Duplicate Address Detection to ensure that it does not interfere with other nodes on the link.¶

An alternative approach for multiple access *NET links to ensure isolation for Client-Proxy/Server communications is through L2 address mappings as discussed in Appendix D. This arrangement imparts a (virtual) point-to-point link model over the (physical) multiple access link.¶

20. OMNI Interfaces on Open Internetworks

Client OMNI interfaces configured over IPv6-enabled underlying interfaces on an open Internetwork without an OMNI-aware first-hop router receive IPv6 RA messages with no OMNI options, while OMNI interfaces configured over IPv4-only underlying interfaces receive no IPv6 RA messages at all (but may receive IPv4 RA messages [RFC1256]). Client OMNI interfaces that receive RA messages with OMNI options configure addresses, on-link prefixes, etc. on the underlying interface that received the RA according to standard IPv6 ND and address resolution conventions [RFC4861] [RFC4862]. Client OMNI interfaces configured over IPv4-only underlying interfaces configure IPv4 address information on the underlying interfaces using mechanisms such as DHCPv4 [RFC2131].¶

Client OMNI interfaces configured over underlying interfaces connected to open Internetworks can apply security services such as VPNs to connect to a Proxy/Server, or can establish a direct link to the Proxy/Server through some other means (see Section 4). In environments where an explicit VPN or direct link may be impractical, Client OMNI interfaces can instead send IPv6 ND messages with OMNI options that include authentication signatures.¶

OMNI interfaces use UDP/IP as *NET encapsulation headers for transmission over open Internetworks with UDP service port number 8060 (see: Section 25.13 and Section 3.6 of [I-D.templin-6man-aero]) for both IPv4 and IPv6 underlying interfaces. The OMNI interface submits original IP packets for OAL encapsulation, then encapsulates the resulting OAL fragments in UDP/IP *NET headers to form carrier packets. (The first four bits following the UDP header determine whether the OAL headers are uncompressed/compressed as discussed in Section 6.4.) The OMNI interface sets the UDP length to the encapsulated OAL fragment length and sets the IP length to an appropriate value at least as large as the UDP datagram.¶

For Client-Proxy/Server (e.g., "Vehicle-to-Infrastructure (V2I)") neighbor exchanges, the source must include an OMNI option with an authentication sub-option in all IPv6 ND messages. The source can apply HIP security services per [RFC7401] using the IPv6 ND message OMNI option as a "shipping container" to convey an authentication signature in a (unidirectional) HIP "Notify" message. For Client-Client (e.g., "Vehicle-to-Vehicle (V2V)") neighbor exchanges, two Clients can exchange HIP "Initiator/Responder" messages coded in OMNI options of multiple IPv6 NS/NA messages for mutual authentication according to the HIP protocol. (Note: a simple Hashed Message Authentication Code (HMAC) such as specified in [RFC4380] or the QUIC-TLS connection-oriented service [RFC9000] can be used as an alternate authentication service in some environments.)¶

When an OMNI interface includes an authentication sub-option, it must appear as the first sub-option of the first OMNI option in the IPv6 ND message which must appear immediately following the IPv6 ND message header. When an OMNI interface prepares a HIP message sub-option, it includes its own (H)HIT as the Sender's HIT and the neighbor's (H)HIT if known as the Receiver's HIT (otherwise 0). If (H)HITs are not available within the OMNI operational environment, the source can instead include other IPv6 address types instead of (H)HITs as long as the Sender and Receiver have some way to associate information embedded in the IPv6 address with the neighbor; such information could include a node identifier, vehicle identifier, MAC address, etc.¶

Before calculating the authentication signature, the source includes any other necessary sub-options (such as Interface Attributes and Origin Indication) and sets both the IPv6 ND message Checksum and authentication signature fields to 0. The source then calculates the authentication signature over the full length of the IPv6 ND message beginning with a pseudo-header of the IPv6 header (i.e., the same as specified in [RFC4443]) and extending over the length of the message. (If the IPv6 ND message is part of an OAL super-packet, the source instead calculates the authentication signature over the remainder of the super-packet up to but not including the trailing OAL Checksum field.) The source next writes the authentication signature into the sub-option signature field and forwards the message.¶

After establishing a VPN or preparing for UDP/IP encapsulation, OMNI interfaces send RS/RA messages for Client-Proxy/Server coordination (see: Section 15) and NS/NA messages for route optimization, window synchronization and mobility management (see: [I-D.templin-6man-aero]). These control plane messages must be authenticated while other control and data plane messages are delivered the same as for ordinary best-effort traffic with source address and/or Identification window-based data origin verification. Upper layer protocol sessions over OMNI interfaces that connect over open Internetworks without an explicit VPN should therefore employ transport- or higher-layer security to ensure authentication, integrity and/or confidentiality.¶

Clients should avoid using INET Proxy/Servers as general-purpose routers for steady streams of carrier packets that do not require authentication. Clients should instead coordinate with other INET nodes that can provide forwarding services instead of burdening the Proxy/Server (or preferably coordinate directly with peer Clients directly). Procedures for coordinating with peer Clients and discovering INET nodes that can provide better forwarding services are discussed in [I-D.templin-6man-aero].¶

Clients that attempt to contact peers over INET underlying interfaces often encounter NATs in the path. OMNI interfaces accommodate NAT traversal using UDP/IP encapsulation and the mechanisms discussed in [I-D.templin-6man-aero]. FHS Proxy/Servers include Origin Indications in RA messages to allow Clients to detect the presence of NATs.¶

Note: Following the initial IPv6 ND message exchange, OMNI interfaces configured over INET underlying interfaces maintain neighbor relationships by transmitting periodic IPv6 ND messages with OMNI options that include HIP "Update" and/or "Notify" messages. When HMAC authentication is used instead of HIP, the Client and Proxy/Server exchange all IPv6 ND messages with HMAC signatures included based on a shared-secret. When QUIC-TLS connections are used, the Client and Proxy/Server observe QUIC-TLS conventions [RFC9000][RFC9001].¶

Note: OMNI interfaces configured over INET underlying interfaces should employ the Identification window synchronization mechanisms specified in Section 6.6 in order to reject spurious carrier packets that might otherwise clutter the reassembly cache. This is especially important in environments where carrier packet spoofing and/or corruption is a threat.¶

Note: NATs may be present on the path from a Client to its FHS Proxy/Server, but never on the path from the FHS Proxy/Server to the Hub where only INET and/or spanning tree hops occur. Therefore, the FHS Proxy/Server does not communicate Client origin information to the Hub where it would serve no purpose.¶

21. Time-Varying MNPs

In some use cases, it is desirable, beneficial and efficient for the Client to receive a constant MNP that travels with the Client wherever it moves. For example, this would allow air traffic controllers to easily track aircraft, etc. In other cases, however (e.g., intelligent transportation systems), the Client may be willing to sacrifice a modicum of efficiency in order to have time-varying MNPs that can be changed every so often to defeat adversarial tracking.¶

The prefix delegation services discussed in Section 15.3 allows Clients that desire time-varying MNPs to obtain short-lived prefixes to send RS messages with source set to the unspecified address (::) and/or with an OMNI option with DHCPv6 Option sub-options. The Client would then be obligated to renumber its internal networks whenever its MNP (and therefore also its OMNI address) changes. This should not present a challenge for Clients with automated network renumbering services, but may disrupt persistent sessions that would prefer to use a constant address.¶

22. (H)HITs and Temporary ULAs

Clients that generate (H)HITs but do not have pre-assigned MNPs can request MNP delegations by issuing IPv6 ND messages that use the (H)HIT instead of a Temporary ULA. In particular, when a Client creates an RS message it can set the source to the unspecified address (::) and destination to link-scoped All-Routers multicast. The IPv6 ND message includes an OMNI option with a HIP message sub-option, and need not include a Node Identification sub-option if the Client's HIT appears in the HIP message. The Client then encapsulates the message in an IPv6 header with the (H)HIT as the source address. The Client then sends the message as specified in Section 15.2.¶

When a Proxy/Server receives the RS message, it notes that the source was the unspecified address (::), then examines the encapsulation source address to determine that the source is a (H)HIT and not a Temporary ULA. The Proxy/Server next invokes the DHCPv6 protocol to request an MNP prefix delegation while using the HIT (in the form of a DUID) as the Client Identifier, then prepares an RA message with source address set to its own ADM-LLA and destination set to the MNP-LLA corresponding to the delegated MNP. The Proxy/Server next includes an OMNI option with a HIP message sub-option and any DHCPv6 prefix delegation parameters. The Proxy/Server finally encapsulates the RA in an IPv6 header with source address set to its own ADM-ULA and destination set to the (H)HIT from the RS encapsulation source address, then returns the encapsulated RA to the Client.¶

Clients can also use (H)HITs and/or Temporary ULAs for direct Client-to-Client communications outside the context of any OMNI link supporting infrastructure. When two Clients encounter one another they can use their (H)HITs and/or Temporary ULAs as original IPv6 packet source and destination addresses to support direct communications. Clients can also inject their (H)HITs and/or Temporary ULAs into a MANET/VANET routing protocol to enable multihop communications. Clients can further exchange IPv6 ND messages (such as NS/NA) using their (H)HITs and/or Temporary ULAs as source and destination addresses.¶

Lastly, when Clients are within the coverage range of OMNI link infrastructure a case could be made for injecting (H)HITs and/or Temporary ULAs into the global MS routing system. For example, when the Client sends an RS to an FHS Proxy/Server it could include a request to inject the (H)HIT / Temporary ULA into the routing system instead of requesting an MNP prefix delegation. This would potentially enable OMNI link-wide communications using only (H)HITs or Temporary ULAs, and not MNPs. This document notes the opportunity, but makes no recommendation.¶

23. Address Selection

Clients use LLAs only for link-scoped communications on the OMNI link. Typically, Clients use LLAs as source/destination IPv6 addresses of IPv6 ND messages, but may also use them for addressing ordinary original IP packets exchanged with an OMNI link neighbor.¶

Clients use MNP-ULAs as source/destination IPv6 addresses in the encapsulation headers of OAL packets. Clients use Temporary ULAs for OAL addressing when an MNP-ULA is not available, or as source/destination IPv6 addresses for communications within a MANET/VANET local area. Clients can also use (H)HITs instead of Temporary ULAs when operation outside the context of a specific ULA domain and/or source address attestation is necessary.¶

Clients use MNP-based GUAs as original IP packet source and destination addresses for communications with Internet destinations when they are within range of OMNI link supporting infrastructure that can inject the MNP into the routing system.¶

Clients use anycast GUAs as OAL and/or *NET encapsulation destination addresses for RS messages used to discover the nearest FHS Proxy/Server. When the Proxy/Server returns a solicited RA, it must also use the same anycast address as the RA OAL/*NET encapsulation source in order to successfully traverse any NATs in the path. The Client should then immediately transition to using the FHS Proxy/Server's discovered unicast OAL/*NET address as the destination in order to minimize dependence on the Proxy/Server's use of an anycast source address.¶

24. Error Messages

An OAL destination or intermediate node may need to return ICMPv6-like error messages (e.g., Destination Unreachable, Packet Too Big, Time Exceeded, etc.) [RFC4443] to an OAL source. Since ICMPv6 error messages do not themselves include authentication codes, OAL nodes can return error messages as an OMNI ICMPv6 Error sub-option in a secured IPv6 ND uNA message.¶

25. IANA Considerations

The following IANA actions are requested in accordance with [RFC8126] and [RFC8726]:¶

   Addresses      Usage                                         Reference
   ---------      -----                                         ---------
   00-52-14       Overlay Multilink Network (OMNI) Interface    [RFCXXXX]

   Code      Name                         Reference
   ---       ----                         ---------
   0         PTB Hard Error               [RFC4443]
   1         PTB Soft Error (loss)        [RFCXXXX]
   2         PTB Soft Error (no loss)     [RFCXXXX]

   Value    Sub-Type name                  Reference
   -----    -------------                  ----------
   0        Pad1                           [RFCXXXX]
   1        PadN                           [RFCXXXX]
   2        Interface Attributes           [RFCXXXX]
   3        Multilink Fwding Parameters    [RFCXXXX]
   4        Traffic Selector               [RFCXXXX]
   5        Geo Coordinates                [RFCXXXX]
   6        DHCPv6 Message                 [RFCXXXX]
   7        HIP Message                    [RFCXXXX]
   8        PIM-SM Message                 [RFCXXXX]
   9        Reassembly Limit               [RFCXXXX]
   10       Fragmentation Report           [RFCXXXX]
   11       Node Identification            [RFCXXXX]
   12       ICMPv6 Error                   [RFCXXXX]
   13       QUIC-TLS Message               [RFCXXXX]
   14-29    Unassigned
   30       Sub-Type Extension             [RFCXXXX]
   31       Reserved by IANA               [RFCXXXX]

   Value    Sub-Type name                  Reference
   -----    -------------                  ----------
   0        NULL                           [RFCXXXX]
   255      Reserved by IANA               [RFCXXXX]

   Value    Sub-Type name                  Reference
   -----    -------------                  ----------
   0        UUID                           [RFCXXXX]
   1        HIT                            [RFCXXXX]
   2        HHIT                           [RFCXXXX]
   3        Network Access Identifier      [RFCXXXX]
   4        FQDN                           [RFCXXXX]
   5        IPv6 Address                   [RFCXXXX]
   6-252    Unassigned                     [RFCXXXX]
   253-254  Reserved for Experimentation   [RFCXXXX]
   255      Reserved by IANA               [RFCXXXX]

   Value    Sub-Type name                  Reference
   -----    -------------                  ----------
   0        RFC4380 UDP/IP Header Option   [RFCXXXX]
   1        RFC6081 UDP/IP Trailer Option  [RFCXXXX]
   2-252    Unassigned
   253-254  Reserved for Experimentation   [RFCXXXX]
   255      Reserved by IANA               [RFCXXXX]

   Value    Sub-Type name                  Reference
   -----    -------------                  ----------
   0        Origin Indication (IPv4)       [RFC4380]
   1        Authentication Encapsulation   [RFC4380]
   2        Origin Indication (IPv6)       [RFCXXXX]
   3-252    Unassigned
   253-254  Reserved for Experimentation   [RFCXXXX]
   255      Reserved by IANA               [RFCXXXX]

   Value    Sub-Type name                  Reference
   -----    -------------                  ----------
   0        Unassigned
   1        Nonce                          [RFC6081]
   2        Unassigned
   3        Alternate Address (IPv4)       [RFC6081]
   4        Neighbor Discovery Option      [RFC6081]
   5        Random Port                    [RFC6081]
   6        Alternate Address (IPv6)       [RFCXXXX]
   7-252    Unassigned
   253-254  Reserved for Experimentation   [RFCXXXX]
   255      Reserved by IANA               [RFCXXXX]

26. Security Considerations

Security considerations for IPv4 [RFC0791], IPv6 [RFC8200] and IPv6 Neighbor Discovery [RFC4861] apply. OMNI interface IPv6 ND messages SHOULD include Nonce and Timestamp options [RFC3971] when transaction confirmation and/or time synchronization is needed. (Note however that when OAL encapsulation is used the (echoed) OAL Identification value can provide sufficient transaction confirmation.)¶

Client OMNI interfaces configured over secured ANET interfaces inherit the physical and/or link-layer security properties (i.e., "protected spectrum") of the connected ANETs. Client OMNI interfaces configured over open INET interfaces can use symmetric securing services such as VPNs or can by some other means establish a direct link. When a VPN or direct link may be impractical, however, the security services specified in [RFC7401] and/or [RFC4380] can be employed. While the OMNI link protects control plane messaging, applications must still employ end-to-end transport- or higher-layer security services to protect the data plane.¶

Strong network layer security for control plane messages and forwarding path integrity for data plane messages between Proxy/Servers MUST be supported. In one example, the AERO service [I-D.templin-6man-aero] constructs an SRT spanning tree with Proxy/Serves as leaf nodes and secures the spanning tree links with network layer security mechanisms such as IPsec [RFC4301] or WireGuard. Secured control plane messages are then constrained to travel only over the secured spanning tree paths and are therefore protected from attack or eavesdropping. Other control and data plane messages can travel over route optimized paths that do not strictly follow the secured spanning tree, therefore end-to-end sessions should employ transport- or higher-layer security services. Additionally, the OAL Identification value can provide a first level of data origin authentication to mitigate off-path spoofing in some environments.¶

Identity-based key verification infrastructure services such as iPSK may be necessary for verifying the identities claimed by Clients. This requirement should be harmonized with the manner in which (H)HITs are attested in a given operational environment.¶

Security considerations for specific access network interface types are covered under the corresponding IP-over-(foo) specification (e.g., [RFC2464], [RFC2492], etc.).¶

Security considerations for IPv6 fragmentation and reassembly are discussed in Section 6.10. In environments where spoofing is considered a threat, OMNI nodes SHOULD employ Identification window synchronization and OAL destinations SHOULD configure an (end-system-based) firewall.¶

27. Implementation Status

AERO/OMNI Release-3.2 was tagged on March 30, 2021, and is undergoing internal testing. Additional internal releases expected within the coming months, with first public release expected end of 1H2021.¶

Many AERO/OMNI functions are implemented and undergoing final integration. OAL fragmentation/reassembly buffer management code has been cleared for public release and will be presented at the June 2021 ICAO mobility subgroup meeting.¶

28. Document Updates

This document does not itself update other RFCs, but suggests that the following could be updated through future IETF initiatives:¶

• [RFC1191]¶
• [RFC4443]¶
• [RFC8201]¶
• [RFC7526]¶

Updates can be through, e.g., standards action, the errata process, etc. as appropriate.¶

29. Acknowledgements

The first version of this document was prepared per the consensus decision at the 7th Conference of the International Civil Aviation Organization (ICAO) Working Group-I Mobility Subgroup on March 22, 2019. Consensus to take the document forward to the IETF was reached at the 9th Conference of the Mobility Subgroup on November 22, 2019. Attendees and contributors included: Guray Acar, Danny Bharj, Francois D'Humieres, Pavel Drasil, Nikos Fistas, Giovanni Garofolo, Bernhard Haindl, Vaughn Maiolla, Tom McParland, Victor Moreno, Madhu Niraula, Brent Phillips, Liviu Popescu, Jacky Pouzet, Aloke Roy, Greg Saccone, Robert Segers, Michal Skorepa, Michel Solery, Stephane Tamalet, Fred Templin, Jean-Marc Vacher, Bela Varkonyi, Tony Whyman, Fryderyk Wrobel and Dongsong Zeng.¶

The following individuals are acknowledged for their useful comments: Amanda Barber, Stuart Card, Donald Eastlake, Michael Matyas, Robert Moskowitz, Madhu Niraula, Greg Saccone, Stephane Tamalet, Eduard Vasilenko, Eric Vyncke. Pavel Drasil, Zdenek Jaron and Michal Skorepa are especially recognized for their many helpful ideas and suggestions. Madhuri Madhava Badgandi, Sean Dickson, Don Dillenburg, Joe Dudkowski, Vijayasarathy Rajagopalan, Ron Sackman and Katherine Tran are acknowledged for their hard work on the implementation and technical insights that led to improvements for the spec.¶

Discussions on the IETF 6man and atn mailing lists during the fall of 2020 suggested additional points to consider. The authors gratefully acknowledge the list members who contributed valuable insights through those discussions. Eric Vyncke and Erik Kline were the intarea ADs, while Bob Hinden and Ole Troan were the 6man WG chairs at the time the document was developed; they are all gratefully acknowledged for their many helpful insights. Many of the ideas in this document have further built on IETF experiences beginning in the 1990s, with insights from colleagues including Ron Bonica, Brian Carpenter, Ralph Droms, Christian Huitema, Thomas Narten, Dave Thaler, Joe Touch, and many others who deserve recognition.¶

Early observations on IP fragmentation performance implications were noted in the 1986 Digital Equipment Corporation (DEC) "qe reset" investigation, where fragment bursts from NFS UDP traffic triggered hardware resets resulting in communication failures. Jeff Chase, Fred Glover and Chet Juzsczak of the Ultrix Engineering Group led the investigation, and determined that setting a smaller NFS mount block size reduced the amount of fragmentation and suppressed the resets. Early observations on L2 media MTU issues were noted in the 1988 DEC FDDI investigation, where Raj Jain, KK Ramakrishnan and Kathy Wilde represented architectural considerations for FDDI networking in general including FDDI/Ethernet bridging. Jeff Mogul (who led the IETF Path MTU Discovery working group) and other DEC colleagues who supported these early investigations are also acknowledged.¶

Throughout the 1990's and into the 2000's, many colleagues supported and encouraged continuation of the work. Beginning with the DEC Project Sequoia effort at the University of California, Berkeley, then moving to the DEC research lab offices in Palo Alto CA, then to Sterling Software at the NASA Ames Research Center, then to SRI in Menlo Park, CA, then to Nokia in Mountain View, CA and finally to the Boeing Company in 2005 the work saw continuous advancement through the encouragement of many. Those who offered their support and encouragement are gratefully acknowledged.¶

This work is aligned with the NASA Safe Autonomous Systems Operation (SASO) program under NASA contract number NNA16BD84C.¶

This work is aligned with the FAA as per the SE2025 contract number DTFAWA-15-D-00030.¶

This work is aligned with the Boeing Information Technology (BIT) Mobility Vision Lab (MVL) program.¶

Appendix A. OAL Checksum Algorithm

The OAL Checksum Algorithm adopts the 8-bit Fletcher algorithm specified in Appendix I of [RFC1146] as also analyzed in [CKSUM]. [RFC6247] declared [RFC1146] historic for the reason that the algorithms had never seen widespread use with TCP, however this document adopts the 8-bit Fletcher algorithm for a different purpose. Quoting from Appendix I of [RFC1146], the OAL Checksum Algorithm proceeds as follows:¶

• "The 8-bit Fletcher Checksum Algorithm is calculated over a sequence of data octets (call them D[1] through D[N]) by maintaining 2 unsigned 1's-complement 8-bit accumulators A and B whose contents are initially zero, and performing the following loop where i ranges from 1 to N:¶

  • A := A + D[i]¶
  • B := B + A¶

  It can be shown that at the end of the loop A will contain the 8-bit 1's complement sum of all octets in the datagram, and that B will contain (N)D[1] + (N-1)D[2] + ... + D[N]."¶

To calculate the OAL checksum, the above algorithm is applied over the N-octet concatenation of the OAL pseudo-header, the encapsulated IP packet and the two-octet trailing checksum field initialized to 0. Specifically, the algorithm is first applied over the 40 octets of the OAL pseudo-header as data octets D[1] through D[40], then continues over the entire length of the original IP packet as data octets D[41] through D[N-2] and finally concludes with the two trailing 0 octets as data octets D[N-1] and D[N].¶

Appendix B. IPv6 ND Message Authentication and Integrity

OMNI interface IPv6 ND messages are subject to authentication and integrity checks at multiple levels. When an OMNI interface sends an IPv6 ND message over an INET interface, it includes an authentication sub-option with a valid signature but does not include an IPv6 ND message checksum. The OMNI interface that receives the message verifies the OAL checksum as a first-level integrity check, then verifies the authentication signature (while ignoring the IPv6 ND message checksum) to ensure IPv6 ND message authentication and integrity.¶

When an OMNI interface sends an IPv6 ND message over an underlying interface connected to a secured network, it omits the authentication sub-option but instead calculates/includes an IPv6 ND message checksum. The OMNI interface that receives the message applies any lower-layer authentication and integrity checks, then verifies both the OAL checksum (if present) and the IPv6 ND message checksum. (Note that optimized implementations can verify both the OAL and IPv6 ND message checksums in a single pass over the data.) When an OMNI interface sends IPv6 ND messages to a synchronized neighbor, it includes an authentication sub-option only if authentication is necessary; otherwise, it calculates/includes the IPv6 ND message checksum.¶

When the OMNI interface calculates the authentication signature or IPv6 ND message checksum, it performs the calculation beginning with a pseudo-header of the IPv6 ND message header and extends over all following OAL packet data up to but not including the trailing OAL checksum field. In particular, for OAL super-packets any additional original IP packets included beyond the end of the IPv6 ND message are simply considered as xensions of the IPv6 ND message for the purpose of the calculation.¶

OAL destinations discard carrier packets with unacceptable Identifications and submit the encapsulated fragments in others for reassembly. The reassembly algorithm rejects any fragments with unacceptable sizes, offsets, etc. and reassembles all others. Following reassembly, the OAL checksum algorithm provides an integrity assurance layer that compliments any integrity checks already applied by lower layers as well as a first-pass filter for any checks that will be applied later by upper layers.¶

Appendix C. VDL Mode 2 Considerations

ICAO Doc 9776 is the "Technical Manual for VHF Data Link Mode 2" (VDLM2) that specifies an essential radio frequency data link service for aircraft and ground stations in worldwide civil aviation air traffic management. The VDLM2 link type is "multicast capable" [RFC4861], but with considerable differences from common multicast links such as Ethernet and IEEE 802.11.¶

First, the VDLM2 link data rate is only 31.5Kbps - multiple orders of magnitude less than most modern wireless networking gear. Second, due to the low available link bandwidth only VDLM2 ground stations (i.e., and not aircraft) are permitted to send broadcasts, and even so only as compact layer 2 "beacons". Third, aircraft employ the services of ground stations by performing unicast RS/RA exchanges upon receipt of beacons instead of listening for multicast RA messages and/or sending multicast RS messages.¶

This beacon-oriented unicast RS/RA approach is necessary to conserve the already-scarce available link bandwidth. Moreover, since the numbers of beaconing ground stations operating within a given spatial range must be kept as sparse as possible, it would not be feasible to have different classes of ground stations within the same region observing different protocols. It is therefore highly desirable that all ground stations observe a common language of RS/RA as specified in this document.¶

Note that links of this nature may benefit from compression techniques that reduce the bandwidth necessary for conveying the same amount of data. The IETF lpwan working group is considering possible alternatives: [https://datatracker.ietf.org/wg/lpwan/documents].¶

Appendix D. Client-Proxy/Server Isolation Through L2 Address Mapping

Per [RFC4861], IPv6 ND messages may be sent to either a multicast or unicast link-scoped IPv6 destination address. However, IPv6 ND messaging should be coordinated between the Client and Proxy/Server only without invoking other nodes on the *NET. This implies that Client-Proxy/Server control messaging should be isolated and not overheard by other nodes on the link.¶

To support Client-Proxy/Server isolation on some *NET links, Proxy/Servers can maintain an OMNI-specific unicast L2 address ("MSADDR"). For Ethernet-compatible *NETs, this specification reserves one Ethernet unicast address TBD5 (see: IANA Considerations). For non-Ethernet statically-addressed *NETs, MSADDR is reserved per the assigned numbers authority for the *NET addressing space. For still other *NETs, MSADDR may be dynamically discovered through other means, e.g., L2 beacons.¶

Clients map the L3 addresses of all IPv6 ND messages they send (i.e., both multicast and unicast) to MSADDR instead of to an ordinary unicast or multicast L2 address. In this way, all of the Client's IPv6 ND messages will be received by Proxy/Servers that are configured to accept packets destined to MSADDR. Note that multiple Proxy/Servers on the link could be configured to accept packets destined to MSADDR, e.g., as a basis for supporting redundancy.¶

Therefore, Proxy/Servers must accept and process packets destined to MSADDR, while all other devices must not process packets destined to MSADDR. This model has well-established operational experience in Proxy Mobile IPv6 (PMIP) [RFC5213][RFC6543].¶

Appendix E. Change Log

<< RFC Editor - remove prior to publication >>¶

Differences from earlier versions to draft-templin-6man-omni-45:¶

• New baseline version with corrections and section reorganizations to improve document flow.¶

Authors' Addresses