| Internet-Draft | Connecting IPv4 Islands over IPv6 Core ( | November 2022 |
| Mishra & Tantsura | Expires 14 May 2023 | [Page] |
The 4Provider Edge (4PE) design explains how to interconnect IPv4 islands over a Multiprotocol Label Switching (MPLS) LDPv6 enabled IPv6-Only core, Segment Routing (SR) enabled SR-MPLS IPv6-Only core or SRv6 IPv6-Only core. The 4PE routers exchange the IPv4 reachability information transparently over the core using the Multiprotocol Border Gateway Protocol (MP-BGP) over IPv6. In doing so, the BGP Next Hop field is used to convey the IPv6 address of the 4PE router so that dynamically established IPv6-signaled MPLS Label Switched Paths (LSPs) or SRv6 Network Programming IPv6 forwarding path instantiation and can be utilized without any explicit tunnel configuration.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 14 May 2023.¶
Copyright (c) 2022 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
The 4PE design explains how to interconnect IPv4 islands over a Multiprotocol Label Switching (MPLS) LDPv6 enabled IPv6-Only core, Segment Routing (SR) enabled SR-MPLS IPv6-Only core or SRv6 IPv6-Only core. The 4PE routers exchange the IPv4 reachability information transparently over the core using the Multiprotocol Border Gateway Protocol (MP-BGP) over IPv6. In doing so, the BGP Next Hop field is used to convey the IPv6 address of the 4PE router so that dynamically established IPv6-signaled MPLS Label Switched Paths (LSPs) or SRv6 Network Programming IPv6 forwarding path instantiation and can be utilized without any explicit tunnel configuration.¶
The 4PE design is required as an alternative to the use of standard overlay tunneling technologies such as GRE/IP or any other tunneling technologies which requries explicit tunnel termination at the tunnel endpoints which creates added layer of complexity to the existing MPLS or Segment routing underlay transport layer. The 4PE design provides a solution for MPLS as well as Segment Routing environment, where all tunnels are established dynamically using existing Service Provider Network MPLS signalling or SRv6 Network Programming thereby addressing environments where the effort to configure and maintain explicitly configured tunnels is not acceptable.¶
This design specifies operations of the 4PE approach for interconnection of IPv4 islands over an MPLS LDP IPv6 core or Segment Routing SR-MPLS IPv6 core or SRv6 core. The approach requires that the Provider Edge (PE) routers Provider Edge - Customer Edge (PE-CE) connections to Customer Edge (CE) IPv4 islands to be Dual Stack using Multiprotocol BGP (MP-BGP) routers [RFC4760], while the core is a [RFC5565] Softwire Mesh Framework single protocol Provider (P) Core routers, are required only to support IPv6-Only dataplane to transport IPv4 packets over an IPv6-Only Core supporting three core technologies, MPLS LDPv6 [RFC5036] and Segment Routing, SR-MPLS [RFC8660] and Segment Routing IPv6 (SRv6) SRv6 Network Programming [RFC8986]. The approach uses MP-BGP over IPv6, relies on identification of the 4PE routers by their IPv6 address, and uses an underlay transport label switched IPv6-signaled MPLS, SR-MPLS LSP's, underlay SRv6 SRv6-TE or SRv6 SRv6-BE Best Effort path instantiation which does not require any explicit tunnel configurations.¶
Throughout this document, the terminology of [RFC2460] and [RFC4364] is used.¶
In this document an 'IPv4 island' is a network running native IPv4 as per [RFC2460]. A typical example of an IPv4 island would be a customer's IPv4 site connected via its IPv4 Customer Edge (CE) router to one (or more) Dual Stack Provider Edge router(s) of a Service Provider. These Dual Stacked or IPv4-Only Provider Edge routers (4PE) are connected to an IPv6 MPLS core network.¶
The interconnection method described in this document typically applies to an Internet Service Provider (ISP) that has an MPLS LDP IPv6 core, Segment Routing SR-MPLS IPv6 core or SRv6 core, that is already offering IPv6 BGP/MPLS VPN services, that wants to continue support IPv4 services to its customers. These 4PE PE Edge routers provide connectivity to the Customer Edge (CE) IPv4 islands Edge routers. They may also provide other services simultaneously (IPv6 connectivity, IPv6 L3VPN services, IPv6 L2VPN services, etc.). With the 4PE approach, no tunnels need to be explicitly configured, and no IPv6 headers need to be inserted in front of the IPv4 packets between the customer and provider edge, PE-CE Demark.¶
The PE-CE interface between the edge router of the IPv4 island Customer Edge (CE) router and the 4PE router is a native IPv4 interface which can be multiple physical or logical. Static routing or a dynamic routing protocol Interior Gateway Protocol IGP, Open Shortest Path First (OSPF) or Intermediate System Intermediate System (ISIS) or Exterior Gatway Protocol such as BGP may run between the CE router and the 4PE router for the distribution of IPv4 Network Layer Reachability Information (NLRI).¶
The 4PE design described in this document can be used for customers that require both IPv4 and IPv6 service as well as for customers that require IPv4-Only connectivity thus providing global IPv4 reachability.¶
Deployment of the 4PE approach over an existing IPv6 MPLS or Segment Routing core does not require an introduction of new mechanisms in the core underlay transport. Configuration and operations of the 4PE approach has similarities with the configuration and operations of an IPv4 VPN service [RFC4364] or IPv6 VPN service [RFC4659] over an IPv6 MPLS or Segment Routing core because they all use MP-BGP to distribute IPv4 Network Layer Reachability Information (NLRI) for transport over an IPv6 Core.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
Each IPv4 site is connected to at least one Provider Edge router that is located on the border of the MPLS LDP IPv6 or Segment Routing SR-MPLS IPv6 or SRv6 core. The PE router providing IPv4 connectivity to the IPv4 Islands over an IPv6-Only Core is called a 4PE router. The 4PE router MUST be IPv4 and IPv6 dual stack . The 4PE router MUST be configured with at least one IPv6 address on the IPv6 side and at least one IPv4 address on the IPv4 side. In the MPLS LDP IPv6 and SR-MPLS IPv6 Core scenario, the IPv6 address needs to be routable in the IPv6 core. For the MPLS LDP IPv6 Core there MUST be an LDP IPv6 label binding, and for SR-MPLS an IPv6 Prefix / Node SID label binding and for SRv6 SRH processing of SRv6 SID list [RFC8754] and SRv6 Network Programming [RFC8986] SRv6 End.DX (Cross Connect to Next Hop) and SRv6 BGP Overlay Services [RFC9252]¶
The 4PE router receiving IPv4 packets from the local Attachment Circuit (AC) PE-CE IPv4-Only or IPv4 and IPv6 Dual Stacked interface "Source Sending" location IPv4 Site is called the Ingress 4PE router relative to these IPv4 packets sent by the CE IPv4 Island. The 4PE router forwarding IPv4 packets from the local Attachment Circuit (AC) PE-CE IPv4-Only or IPv4 and IPv6 Dual stacked interface Destinaton IPv4 Site Receiving location is called the Egress 4PE router relative to these IPv4 packets received by the CE IPv4 Island.¶
Every ingress 4PE router can signal an IPv6 MPLS LSP or instantiate an SRv6 Best Effort (BE) or Segment Routing Traffic Engineering (SR-TE) [RFC9256]. path to send to any egress 4PE router without injecting any additional prefixes into the IPv6 core.¶
Interconnecting IPv4 islands over an IPv6 MPLS or Segment Routing core takes place through the following steps:¶
1. Exchange IPv4 reachability information among 4PE Ingress and Egress PE routers using MP- BGP [RFC2545]:¶
The 4PE routers MUST exchange the IPv4 prefixes over MP-BGP sessions as per [RFC2545] running over IPv6. The MP-BGP Address Family Identifier (AFI) used MUST be IPv4 (value 1). In doing so, the 4PE routers convey their IPv6 address as the BGP Next Hop for the advertised IPv4 prefixes. The IPv6 address of the egress 4PE next hop router MUST be encoded using [RFC8950] next hop encoding for the BGP Next Hop field with a length of 16 or 32 bytes. The next hop encoding [RFC8950] is constructed using MP-BGP for IPv6 [RFC2545] is a 16 byte IPv6 Global Unicast Address followed by the 16 byte IPv6 Link Local Address if the Next Hop. In addition, the 4PE router MUST bind a label to the IPv4 prefix as per [RFC8277]. The Subsequence Address Family Identifier (SAFI) used in MP-BGP MUST be the "label" SAFI (value 4) as defined in [RFC8277] called BGP Labeled Unicast (BGP-LU). BGP Labeled Unicast hereinafter will be referred to as BGP-LU. The Ingress and Egress PE Label Stack on the 4PE router contains the Service label with Bottom of Stack "S" bit set and contains the IPv4 NLRI prefixes "labeled" using BGP-LU, IPv4 Address Family Identifier (AFI) IPv4 (value 1) Subsequent Address Family Identifier (SAFI)(value 4).¶
2. Transport IPv4 packets from the ingress 4PE router to the egress 4PE router over IPv6-signaled LSPs or SRv6 BE or SR-TE instantiated path over an IPv6-only core:¶
The Ingress 4PE router MUST forward IPv4 NLRI as Labeled prefixes using BGP-LU SAFI over the IPv6-signaled LSP towards the Egress 4PE router identified by the IPv4 address advertised in the IPv6 next hop encoding per [RFC8950].¶
The 4PE design is fully applicable to both full mesh BGP peering between all Ingress and Egress PE's as well as when Route Reflectors are utilized as per BGP specification [RFC4271].¶
In this design, using IPv6 Next hop encoding defined in [RFC8950] allows a 4PE router that has to forward an IPv4 packets to automatically determine the IPv6-signaled LSP to use for a particular IPv4 destination by using the MP-BGP IPv4 NLRI.¶
The IPv6-signaled LSPs can be established using any existing technique for label setup [RFC3031] using Label Distribution Protocol (LDP) [RFC5036] or Resource Reservation Protocol (RSVP-TE) [RFC3209].¶
To ensure interoperability among systems that implement the 4PE design described in this document, all such systems MUST support building the topmost transport label tunneling using IPv6-signaled MPLS LSPs established by LDP [RFC5036] or Resource Reservation Protocol (RSVP-TE) [RFC3209].¶
When tunneling IPv4 packets over the IPv6 MPLS core, rather than successively prepend an IPv6 header and then perform label imposition based on the IPv6 header, the ingress 4PE Router MUST directly perform label imposition of the IPv4 header without prepending any IPv6 header. The (outer) label imposed MUST correspond to the IPv6- signaled LSP starting on the ingress 4PE Router and ending on the egress 4PE Router.¶
While this design concept could theoretically operate in some situations using a single level of labels, there are significant advantages in using a second level of labels that are bound to IPv6 prefixes via MP-BGP advertisements in accordance with [RFC8277].¶
One of the main reasons and requirements for the use of a second level bottom of stack service label is that it allows for Penultimate Hop Popping (PHP) on the IPv6 Label Switch Router (LSR) Provider (P) node, upstream of the egress 4PE router, this is because it still transmits the MPLS topmost label preserved due to 2 label, label stack, even after the PHP, instead of having to transmit unlableled IPv4 packets and encapsulate them appropriately.¶
Another critical reason for the second label is that an existing IPv6-signaled LSP that is using "IPv6 Explicit NULL label" over the last hop (e.g., because that LSP is already being used to transport IPv6 traffic with the Pipe Diff-Serv Tunneling Model as defined in [RFC3270]) could not be used to carry IPv4 with a single label since the "IPv6 Explicit NULL label" cannot be used to carry native IPv4 traffic (see [RFC3032]), while it could be used to carry Labeled IPv4 traffic (see [RFC4182]).¶
This is why a second label MUST be used with the 4PE design.¶
The label bound by MP-BGP to the IPv4 prefix indicates to the egress 4PE Router that the packet is an IPv4 packet. This label advertised by the egress 4PE Router with MP-BGP MAY be an arbitrary label value, which identifies an IPv4 routing context or outgoing interface to forward the packet, or could be the IPv4 Explicit Null Label Pipe Diff-Serv Tunneling Model use case as defined in [RFC3270]). An ingress 4PE Router MUST be able to accept any such advertised label.¶
Every link in the IPv4 Internet must have an MTU of 576 octets or larger per [RFC1122]. Therefore, on MPLS links that are used for transport of IPv4, as per the 4PE approach, and that do not support link-specific fragmentation and reassembly, the MTU must be configured to at least 576 octets plus the MPLS label stack encapsulation overhead bytes.¶
Some IPv4 hosts might be sending packets larger than the MTU available in the IPv6 MPLS core and rely on Path MTU discovery to learn about those links. To simplify MTU discovery operations, one option is for the network administrator to engineer the MTU on the core facing interfaces of the ingress 4PE consistent with the core MTU. ICMP ' Destination Unreachable' messages can then be sent back by the ingress 4PE without the corresponding packets ever entering the MPLS core. Otherwise, routers in the IPv6 MPLS network have the option to generate an ICMP "Destination Unreachable" Fragmentation Required Type 3 Code 4 message using mechanisms as described in Section 2.3.2, "Tunneling Private Addresses through a Public Backbone" of [RFC3032].¶
Note that in the above case, should a core router with an outgoing link with an MTU smaller than 1280 receive an encapsulated IPv4 packet larger than 576, then the mechanisms of [RFC3032] may result in the "Unreachable" message never reaching the sender. This is because, according to [RFC4443], the core router will build an ICMP "Unreachable " message filled with the invoking packet up to 576 bytes, and when forwarding downstream towards the egress PE as per [RFC3032], the MTU of the outgoing link will cause the packet to be dropped. This may cause significant operational problems; the originator of the packets will notice that his data is not getting through, without knowing why and where they are discarded. This issue would only occur if the above recommendation (to configure MTU on MPLS links of at least 1280 octets plus encapsulation overhead) is not adhered to (perhaps by misconfiguration).¶
Segment Routing (SR) [RFC3031] leverages the source-routing paradigm to steer packets from a source node through a controlled set of instructions, called segments, by prepending the packet with an SR header in the MPLS data plane SR-MPLS [RFC8660] through a label stack or IPv6 data plane using an Segment Routing Header (SRH) header via SRv6 [RFC8754] to construct an SR path. Segment Routing will be referred to hereinafter as "SR". SR uses instructions called segments which can be topological segments used for transport underlay traffic steering or service instructions for overlay services. SR's Source Routing Architecture provides a mechansim to steer a flow onto a topological path, while maintaining per flow state only on the ingress source nodes within the SR domain. SR-MPLS reuses the Interior Gateway Protocol (IGP) control plane as well as the MPLS forwarding plane functions as the SR segments are instantiated as MPLS labels and the Segment Routing SR-MPLS Header is instantiated as a stack of MPLS labels. SR-MPLS L2 VPN and L3 VPN services can be steered using Traffic Engineered paths using SR-TE Policy coloring for the path instantiation per [RFC9256] and [I-D.ietf-idr-segment-routing-te-policy].¶
In the 4PE design with Segment Routing SR-MPLS architecture [RFC8660] the design is identical as the IPv6 signaled LSP from ingress PE to egress PE is identical but now with underlay traffic steering capabilities. For the 4PE overlay the design for SR-MPLS is identical to MPLS where the Ingress and Egress PE Label Stack on the 4PE router contains the Service label with Bottom of Stack "S" bit set and contains the IPv4 NLRI prefixes "labeled" using BGP-LU, IPv4 Address Family Identifier (AFI) IPv4 (value 1) Subsequent Address Family Identifier (SAFI)(value 4).¶
SR-MPLS can use Inter-AS options for 4PE procedures which is identical to MPLS as well as can use SR-TE Policy and Binding SID for candidate path per [RFC9256] and [I-D.ietf-idr-segment-routing-te-policy].¶
Segment Routing (SR) [RFC3031] SRv6 leverages the source-routing paradigm to steer packets from a source node through a controlled set of instructions, called segments, by prepending the packet with a new SR header over an IPv6 data plane called an IPv6 Routing Extension Header type 4 called a Segment Routing Header (SRH) header with IPv6 SRH encoding [RFC8754] to construct an SR steered path. SRv6 Network Programming framework provides the mechanism based on segment endpoint behaviors to encode a sequence of instructions called Segments into an IPv6 header. SRv6 defines a topological or service segment as an IPv6 address with is called hereinafter a SID or "Segment ID". Each SID is encoded into an SRH header per [RFC8754]on the SR domain source node in the SR domain to steer a flow onto a topological path. In SRv6 each SID is an IPv6 address with format LOC:FUNC:ARG where the LOCATOR field "LOC" is the L most significant bits of the SID, followd by F bits of FUNCTION field "FUNC" and A bits of ARGUMENT "ARG". Each node in the SRv6 domain has a "LOC" prefix assigned which is routable and it leads to the SRv6 node which instantiates the SID by performing the endpoint processing on the node. The SRv6 SID FUNCTION "FUNC" field is used to encode the BGP/MPLS L3 VPN [RFC4364] or BGP EVPN Service labels [RFC7432] as defined in SRv6 BGP Overlay Services [RFC9252]. Intermediate nodes within an SRv6 domain process the topolocial SID at each segment endpoint defined in the SRH header until the packet reaches the egress PE where decapsulation happens similar to BGP/MPLS L3 VPN [RFC4364], where the service labels encoded in the FUNC field can be instantiated and processed for the corresponding Layer 2 VPN and Layer 3 VPN service specific endpoint functions. SRv6 based BGP services referes to Layer 2 VPN and Layer 3 VPN overlay services with BGP as a control plane and SRv6 as a Data Plane to provide Best Effort (BE) which means that an SRH is not present and is reffered to as SRv6-BE. SRv6 based BGP services referes to Layer 2 VPN and Layer 3 VPN overlay services with BGP as a control plane and SRv6 as a Data Plane to provide Traffic Engineered (TE) which means that an SRH is present is reffered to as SRv6-TE policy for SRH topological instruction encoding for SR-TE Policy coloring for path steering instantiation per [RFC9256] and [I-D.ietf-idr-segment-routing-te-policy]. SRv6 Service SID and refers to an SRv6 SID associated with one of the service-specific endpoint behaviors on the advertising PE router such as END.DT (Table Lookup in a VRF) or END.DX (Cross Connect to a Next Hop) behaviors for Layer 3 VPN services defined in SRv6 Network Programming [RFC8986] BGP Prefix SID Attribue is used to carry the SRv6 SIDs and their associaed BGP Address Families and defines a SRv6 L3 Service TLV which encodes the SRv6 Service SID Information for SRv6 based L3 Services. SRv6-BE providing "Best Effort" connectivity where an SRH is not present, the egress PE signals the SRv6 Service SID with the BGP overlay service route and encapsulates the payload in an outer IPv6 header where the destination address is the SRv6 Service SID enclosed in SRv6 Service TLV(s) provided by the Egress PE in which case the underlay need only support plan IPv6 forwarding. SRv6-TE provides connectivity over a "Traffic Engineered" (TE) path by encapsulating the payload packet in an outer IPv6 header with the segment list of the SR policy related to the SLA along with SRv6 Service SID enclosed in SRv6 Service TLV(s) assoicated with route using SRH segment list encoding [RFC8754] from ingress PE to egress PE, the egress PE colors the overlay service route with a Color Extended Community [I-D.ietf-idr-segment-routing-te-policy] to instantiate the steering of flows with per flow state only maintained on the SRv6 source node and all underlay nodes whos SRv6 SID are part of the SRH Segment List MUST support the SRv6 Data Plane forwarding.¶
In the 4PE design over an SRv6 network using SRv6 Netowrk Programming [RFC8986] forwarding plane would use endpoint behavior "Endpoint with decapsulation and IPv4 cross-connect" behavior ("End.DX4" for short) is a variant of the End.X behavior for Global Table IPv4 Routing over SRv6 Core. The End.DX4 SID MUST be the last segment in an SR Policy, and it is associated with one or more L3 IPv4 adjacencies and and SRv6 BGP Overlay Services [RFC9252] where the next hop encoding [RFC8950] is constructed using MP-BGP for IPv6 [RFC2545] is a 16 byte IPv6 Global Unicast Address followed by the 16 byte IPv6 Link Local Address if the Next Hop. In the 4PE design the SRv6 L3 Service SID is encoded as part of the SRv6 L3 Service TLV for SRv6 Netowrk Programming [RFC8986] endpoint behavior End.DX4 BGP Prefix SID Attribute encoding of SRv6 Service SID, SRv6 L3 Service TLV encoding [RFC9252] advertised by egress PEs which supports SRv6 based Layer 3 Services along with Service SID enclosed in SRv6 Layer 3 Service TLV, Label field for an IPv4 prefix is encoded with 20-bit label value set as specified by BGP-LU [RFC8277] to the whole or portion of the "FUNCTION" part of the SRv6 SID when the transposition encoding scheme is used or otherwise set to NULL. The "FUNCTION" part of the SRv6 SID now carries the overlay 4PE BGP-LU IPv4 Labeled prefix identical to MPLS and SR-MPLS.¶
In the 4PE design over an SRv6 network using SRv6 Netowrk Programming [RFC8986] forwarding plane would use endpoint behavior "Endpoint with decapsulation and specific IPv4 table lookup" behavior ("End.DT4" for short) is a variant of the End.T behavior for Global Table IPv4 Routing over SRv6 Core, The End.DT4 SID MUST be the last segment in an SR Policy, and a SID instance is assocated with a IPv4 FIB Table T. and SRv6 BGP Overlay Services [RFC9252] where the next hop encoding [RFC8950] is constructed using MP-BGP for IPv6 [RFC2545] is a 16 byte IPv6 Global Unicast Address followed by the 16 byte IPv6 Link Local Address if the Next Hop. In the 4PE design the SRv6 L3 Service SID is encoded as part of the SRv6 L3 Service TLV for SRv6 Netowrk Programming [RFC8986] endpoint behavior End.DT4 BGP Prefix SID Attribute encoding of SRv6 Service SID, SRv6 L3 Service TLV encoding [RFC9252] advertised by egress PEs which supports SRv6 based Layer 3 Services along with Service SID enclosed in SRv6 Layer 3 Service TLV, Label field for an IPv4 prefix is encoded with 20-bit label value set as specified by BGP-LU [RFC8277] to the whole or portion of the "FUNCTION" part of the SRv6 SID when the transposition encoding scheme is used or otherwise set to NULL. The "FUNCTION" part of the SRv6 SID now carries the overlay 4PE BGP-LU IPv4 Labeled prefix identical to MPLS and SR-MPLS.¶
SRv6 can use Inter-AS options for 4PE procedures which is equivalent to MPLS using SRv6 Service SID enocded in BGP Prefix SID Attribute as well as can use SR-TE Policy and Binding SID for candidate path per [RFC9256] and [I-D.ietf-idr-segment-routing-te-policy].¶
This section discusses the use case where two IPv4 islands are connected to different Core Autonomous Systems (ASes)and utilizes 4 PE to connect the two Core ASes together. The Inter-AS connectivity is established by connecting the PE from one AS to the PE of another AS, whereby the PE providing global table routing reachability between ASes, as a 4PE router, is acting as an Autonomous System Boundary Router (ASBR) to provide the Inter-AS ASBR to ASBR, PE to PE connectivity between ASN's. In the 4PE design the Inter-AS link extends the underlay transport LSP so it is now extended between the ASes. Bottom of Stack S bit is set and using BGP-LU IPv4 BGP Labeled Unicast all the IPv4 prefixes can now be advertised between the ASes.¶
Like in the case of multi-AS backbone operations for IPv6 VPNs described in Section 10 of [RFC4364], there are three inter-as design options and a fourth option defined in [I-D.mapathak-interas-ab] that are described below.¶
This 4PE Inter-AS extension involves the advertisement of IPv4 prefixes (non-Labeled) using Inter-AS Style procedure (a).¶
This design is the equivalent for exchange of IPv4 prefixes to Inter-AS Style procedure (a) Back to Back CE (no-labeled) Inter-AS path where each PE acts like a CE (No MPLS) as described in Section 10 of [RFC4364] for the exchange of VPN-IPv4 prefixes. In the Inter-AS Style Procedure (a) the Control plane carrying the (non-labeled) prefixes is together per VRF subinterfaces with the Data Plane forwarding over the Inter-AS ASBR to ASBR link.¶
In this design, the Source 4PE routers within the Source AS use IBGP MP-BGP [RFC4760] carrying IPv4 NLRI over an IPv6 Next Hop using IPv6 Next hop encoding [RFC8950] and BGP-LU [RFC8277] to advertise labeled IPv4 prefixes to a Route Reflector to which it is a client, which then advertises the labeled IPv4 prefixes to an Autonomous System Border Router (ASBR) 4PE router which is also a client of the route reflector, connecting eBGP to another Autonomous System Border Router (ASBR) 4PE router. The ASBR then uses eBGP to advertise the (non-labeled) IPv4 prefixes to an ASBR in another AS, which in turn advertises the IPv4 prefixes to a route reflector within that AS of which it is a client which then advertises the IPv4 prefixes to all the 4PE routers in that directly connected AS or as described earlier in this specification to another ASBR, which in turn repeats the Inter-AS Procedure (a) herinafter in a case where ASN's are linked togetther with multiple 4PE AS hops.¶
There may be one, or multiple, ASBR interconnection(s) across any two ASes. IPv4 MUST to be activated on the Inter-AS ASBR to ASBR (non-labeled) links and each ASBR 4PE router MUST have at least one IPv4 address on the interface connected to the Inter-AS ASBR to ASBR, PE to PE link.¶
No inter-AS LSPs are used are used in this Inter-AS Procedure (a) as described in Section 10 of [RFC4364]. There is effectively a separate mesh of LSPs across the 4PE routers within each AS for which the (non-labeled) IPv4 prefixes are advertised within the AS as BGP-LU IPv4 labled prefixes carried in the IPv6 signaled transport LSP mesh.¶
In this design, the ASBR exchanging IPv4 prefixes MUST peer over IPv4. The exchange of IPv4 prefixes MUST be carried out as per [RFC4760].¶
This 4PE Inter-AS extension involves the advertisement of labeled IPv4 prefixes over a segmented LSP using Inter-AS Style procedure (b). In this 4PE extension of Inter-AS Style procedure (b) the 4PE IPv4 BGP-LU labeled Unicast RIB is maintained on the ASBR.¶
This design is the equivalent for exchange of IPv4 prefixes to Inter-AS procedure (b) described in Section 10 of [RFC4364] for the exchange of VPN-IPv4 prefixes. In the Inter-AS Style Procedure (b) the Control plane carrying the Service label prefixes is together in the label stack with the Data Plane forwarding over the Inter-AS ASBR to ASBR link.¶
In this design, the Source 4PE routers within the Source AS use IBGP MP-BGP [RFC4760] carrying IPv4 NLRI over an IPv6 Next Hop using IPv6 Next hop encoding [RFC8950] and BGP-LU [RFC8277] to advertise labeled IPv4 prefixes to a Route Reflector to which it is a client, which then advertises the labeled IPv4 prefixes to an Autonomous System Border Router (ASBR) 4PE router which is also a client of the route reflector, connecting eBGP to another Autonomous System Border Router (ASBR) 4PE router. The ASBR then uses eBGP to advertise the labeled IPv4 prefixes to an ASBR in another AS, which in turn advertises the IPv4 prefixes to a route reflector within that AS of which it is a client which then advertises the IPv4 prefixes to all the 4PE routers in that directly connected AS or as described earlier in this specification to another ASBR, which in turn repeats the Inter-AS Procedure (a) herinafter in a case where ASN's are linked togetther with multiple 4PE AS hops.¶
There may be one, or multiple, ASBR interconnection(s) across any two ASes. The label stack on the ASBR to ASBR, PE to PE link is 2 labels deep, with the IPv6 tompost transport label IPv6 signaled LSP using BGP-LU IPv6 Labeled Unicast, IPv6 Address Family Identifier (AFI) IPv4 (value 2) Subsequent Address Family Identifier (SAFI)(value 4) and Bottom of Stack BGP-LU IPv4 labeled Unicast Service label, IPv4 Address Family Identifier (AFI) IPv4 (value 1) Subsequent Address Family Identifier (SAFI)(value 4) Thus IPv4 is not required to be activated on the Inter-AS ASBR to ASBR PE to PE links as IPv4 is tunnled through the IPv6 signaled LSP.¶
This 4PE Inter-AS procedure (b) described in Section 10 of [RFC4364] requires that there be label switched paths established across ASes. Hence the corresponding considerations described for procedure (b) in Section 10 of [RFC4364] apply equally to this design regarding trust relationship between Service Providers in extending the Inter-AS LSP between ASBR's.¶
This 4PE Inter-AS extension involves the Route Reflector to Route Reflector Control Plane Multi-hop eBGP advertisement of labeled IPv4 Unicast prefixes between source and destination ASes, with Inter-AS link transport underlay IPv6 signaled LSP eBGP advertisement of labeled Unicast IPv4 prefixes from AS to neighboring AS. In this 4PE extension of Inter-AS Style procedure (c), the 4PE IPv4 BGP-LU labeled Unicast RIB is not maintained on the ASBR.¶
This design is the equivalent for exchange of IPv4 prefixes to Inter-AS procedure (c) described in Section 10 of [RFC4364] for exchange of VPN-IPv4 prefixes. In the Inter-AS Style Procedure (c) the Control plane carrying the Service label prefixes eBGP Multihop, Route Reflector to Route Reflector is separated from the data plane forwarding over the Inter-AS ASBR to ASBR link which caries the underlay PE loopbacks advertised using BGP-LU between the Source and Destination AS over the Inter-AS ASBR-ASBR link. The Core AS underlay /128 PE loopbacks must be advertised in IPv6 Address Family Identifier (AFI) IPv4 (value 2) Subsequent Address Family Identifier (SAFI)(value 4).¶
In this design, the Source 4PE routers within the Source AS use IBGP MP-BGP [RFC4760] carrying IPv4 NLRI over an IPv6 Next Hop using IPv6 Next hop encoding [RFC8950] and BGP-LU [RFC8277] to advertise the control plane labeled IPv4 prefixes to a Route Reflector to which it is a client, which then advertises the labeled IPv4 Unicast prefixes over an eBGP Multihop Inter-AS peering to the route reflector in the Destination AS. The ASBR in the Source AS over the Inter-AS ASBR to ASBR link then uses eBGP to advertise the core underlay Labeled Unicast IPv6 PE loopabcks prefixes in the underlay to an ASBR in Destination AS, which in turn advertises the IPv6 PE loopabcks prefixes to a route reflector within the Destination AS of which it is a client which then advertises the PE loopabcks IPv6 prefixes to all the PE routers within the AS to establish an end to end LSP from ingress PE in the Source AS to egress PE in the Destination AS.¶
IPv4 need not be activated on the Inter-AS ASBR to ASBR, PE to PE links.¶
The considerations described for procedure (c) in Section 10 of [RFC4364] with respect to possible use of multi-hop eBGP connections via route-reflectors in different ASes, as well as with respect to the use of a third label in case the IPv6 /128 prefixes for the PE routers are NOT made known to the P routers, apply equally to this design for IPv4 underlay transport.¶
There may be one, or multiple, ASBR interconnection(s) across any two ASes. The label stack on the ASBR to ASBR, PE to PE link is 2 labels deep, with the IPv6 tompost transport label IPv6 signaled LSP using BGP-LU IPv6 Labeled Unicast, IPv6 Address Family Identifier (AFI) IPv4 (value 2) Subsequent Address Family Identifier (SAFI)(value 4) and the route reflector to route reflector Multihop eBGP Peering next-hop-unchanged forwarding plane from ingress PE to egress PE loopback with unchanged next-hop is forwarded over the Inter-AS ASBR to ASBR PE-PE link, Bottom of Stack BGP-LU IPv4 labeled Unicast Service label, IPv4 Address Family Identifier (AFI) IPv4 (value 1) Subsequent Address Family Identifier (SAFI)(value 4) Thus IPv4 is not required to be activated on the Inter-AS ASBR to ASBR PE to PE links as IPv4 is tunnled through the IPv6 signaled LSP.¶
This 4PE design for procedure (c) in Section 10 of [RFC4364] requires that there be IPv6 label switched paths established across the ASes leading from a packet's ingress 4PE router to its egress 4PE router. Hence the considerations described for procedure (c) in Section 10 of [RFC4364], with respect to LSPs spanning multiple ASes, apply equally to this design for IPv4.¶
Note that the 4PE Inter-AS extension for procedure (c) in Section 10 of [RFC4364] that the exchange of IPv4 prefixes control plane function can only start after BGP has created IPv6 end to end LSP has established between the ASes.¶
The new MP-BGP extensions defined in [RFC8950] is used to support IPV4 islands over an IPv6 MPLS LDPv6 or SRv6 backbone. In this scenario the PE routers would use BGP Labeled unicast address family (BGP-LU) to advertise BGP with label binding and receive Labeled IPv4 NLRI in the MP_REACH_NLRI along with an IPv6 Next Hop from the Route Reflector (RR).¶
MP-BGP Reach Pseudo code:¶
If ((Update AFI == IPv4)¶
and (Length of next hop == 16 Bytes || 32 Bytes))¶
{¶
This is an IPv4 route, but¶
with an IPv6 next hop;¶
}¶
The MP_REACH_NLRI is encoded with:¶
During BGP Capability Advertisement, the PE routers would include the following fields in the Capabilities Optional Parameter:¶
There are not any IANA considerations.¶
The extensions defined in this document allow BGP to propagate reachability information about IPv6 prefixes over an MPLS IPv4 core network. As such, no new security issues are raised beyond those that already exist in BGP-4 and use of MP-BGP for IPv6.¶
The security features of BGP and corresponding security policy defined in the ISP domain are applicable.¶
For the inter-AS distribution of IPv6 prefixes according to case (a) of Section 4 of this document, no new security issues are raised beyond those that already exist in the use of eBGP for IPv6 [RFC2545].¶