| Internet-Draft | TE YANG Data Model | March 2023 |
| Saad, et al. | Expires 13 September 2023 | [Page] |
This document defines a YANG data model for the provisioning and management of Traffic Engineering (TE) tunnels, Label Switched Paths (LSPs), and interfaces. The model covers data that is independent of any technology or dataplane encapsulation and is divided into two YANG modules that cover device-specific, and device independent data.¶
This model covers data for configuration, operational state, remote procedural calls, and event notifications.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 13 September 2023.¶
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
YANG [RFC6020] and [RFC7950] is a data modeling language that was introduced to define the contents of a conceptual data store that allows networked devices to be managed using NETCONF [RFC6241]. YANG has proved relevant beyond its initial confines, as bindings to other interfaces (e.g. RESTCONF [RFC8040]) and encoding other than XML (e.g. JSON) are being defined. Furthermore, YANG data models can be used as the basis of implementation for other interfaces, such as CLI and programmatic APIs.¶
This document describes a YANG data model for Traffic Engineering (TE) tunnels, Label Switched Paths (LSPs), and interfaces. The data model is divided into two YANG modules. The module 'ietf-te.yang' includes data that is generic and device-independent, while the module 'ietf-te-device.yang' includes data that is device-specific.¶
The document describes a high-level relationship between the modules defined in this document, as well as other external protocol YANG modules. The TE generic YANG data model does not include any data specific to a signaling protocol. It is expected other data plane technology model(s) will augment the TE generic YANG data model.¶
Also, it is expected other YANG modules that model TE signaling protocols, such as RSVP-TE ([RFC3209], [RFC3473]), or Segment-Routing TE (SR-TE) [RFC9256] will augment the generic TE YANG module.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
The following terms are defined in [RFC6241] and are used in this specification:¶
This document also makes use of the following terminology introduced in the YANG Data Modeling Language [RFC7950]:¶
In this document, names of data nodes and other data model objects are prefixed using the standard prefix associated with the corresponding YANG imported modules, as shown in Table 1.¶
| Prefix | YANG module | Reference |
|---|---|---|
| yang | ietf-yang-types | [RFC6991] |
| inet | ietf-inet-types | [RFC6991] |
| rt-types | ietf-routing-types | [RFC8294] |
| te-types | ietf-te-types | [RFC8776] |
| te-packet-types | ietf-te-packet-types | [RFC8776] |
| te | ietf-te | this document |
| te-dev | ietf-te-device | this document |
The tree diagrams extracted from the module(s) defined in this document are given in subsequent sections as per the syntax defined in [RFC8340].¶
This document describes a generic TE YANG data model that is independent of any dataplane technology. One of the design objectives is to allow specific data plane technology models to reuse the TE generic data model and possibly augment it with technology specific data.¶
The elements of the generic TE YANG data model, including TE Tunnels, LSPs, and interfaces have leaf(s) that identify the technology layer where they reside. For example, the LSP encoding type can identify the technology associated with a TE Tunnel or LSP.¶
Also, the generic TE YANG data model does not cover signaling protocol data. The signaling protocol used to instantiate TE LSPs are outside the scope of this document and expected to be covered by augmentations defined in other document(s).¶
The following other design considerations are taken into account with respect to data organization:¶
The Network Management Datastore Architecture (NMDA) [RFC8342] addresses modeling state data for ephemeral objects. This document adopts the NMDA model for configuration and state data representation as per IETF guidelines for new IETF YANG models.¶
The data models defined in this document cover the core TE features that are commonly supported by different vendor implementations. The support of extended or vendor specific TE feature(s) is expected to either be in augmentations, or deviations to this model that are defined in separate documents.¶
The generic TE YANG data model that is defined in "ietf-te.yang" covers the building blocks that are device independent and agnostic of any specific technology or control plane instances. The TE device model defined in "ietf-te-device.yang" augments the generic TE YANG data model and covers data that is specific to a device -- for example, attributes of TE interfaces, or TE timers that are local to a TE node.¶
The TE data models for specific instances of data plane technology exist in separate YANG modules that augment the generic TE YANG data model. The TE data models for specific instances of signaling protocols are outside the scope of this document and are defined in other documents. For example, the RSVP-TE YANG model augmentation of the TE model is covered in a separate document.¶
TE generic +---------+ o: augment
module | ietf-te |o-------------+
+---------+ \
o \
|\ \
| \ TE device module \
| +----------------+ \
| | ietf-te-device | \
| +----------------+ \
| o \
| / \
| / \
+---------------+ +---------------+
RSVP-TE module | ietf-rsvp-te^ |o . | ietf-te-mpls^ |
+---------------+ \ +---------------+
| \
| \
| \
| \
| \
o +-------------------+
+------------+ | ietf-rsvp-otn-te^ |
RSVP module | ietf-rsvp^ | +-------------------+
+------------+ RSVP-TE with OTN
extensions
X---oY indicates that module X augments module Y
^ indicates a module defined in other documents
The generic TE YANG module ('ietf-te') is meant for the management and operation of a TE network. This includes creating, modifying and retrieving information about TE Tunnels, LSPs, and interfaces and their associated attributes (e.g. Administrative-Groups, SRLGs, etc.).¶
A full tree diagram of the TE model is shown in the Appendix in Figure 13.¶
The 'te' container is the top level container in the 'ietf-te' module. The presence of the 'te' container enables TE function system wide. Below provides further descriptions of containers that exist under the 'te' top level container.¶
There are three further containers grouped under the 'te' container as shown in Figure 2 and described below.¶
globals:¶
The 'globals' container maintains the set of global TE attributes that can be applicable to TE Tunnels and interfaces.¶
tunnels:¶
The 'tunnels' container includes the list of TE Tunnels that are instantiated. Refer to Section 5.1.2 for further details on the properties of a TE Tunnel.¶
lsps:¶
The 'lsps' container includes the list of TE LSP(s) that are instantiated for TE Tunnels. Refer to Section 5.1.3 for further details on the properties of a TE LSP.¶
The model also contains two Remote Procedure Calls (RPCs) as shown in Figure 13 and described below.¶
tunnels-path-compute:¶
A RPC to request path computation for a specific TE Tunnel. The RPC allows requesting path computation using atomic and stateless operation. A tunnel may also be configured in 'compute-only' mode to provide stateful path updates - see Section 5.1.2 for further details.¶
tunnels-action:¶
An RPC to request a specific action (e.g. reoptimize, or tear-and-setup) to be taken on a specific tunnel or all tunnels.¶
Figure 13 shows the relationships of these containers and RPCs within the 'ietf-te' module.¶
module: ietf-te
+--rw te!
+--rw globals
| ...
+--rw tunnels
| ...
+--ro lsps
...
rpcs:
+---x tunnels-path-compute
| +---w input
| | ...
| +--ro output
| ...
+---x tunnels-actions
+---w input
| ...
+--ro output
...
The 'globals' container covers properties that control a TE feature's behavior system-wide, and its respective state as shown in Figure 3 and described in the text that follows.¶
+--rw globals
| +--rw named-admin-groups
| | +--rw named-admin-group* [name]
| | ...
| +--rw named-srlgs
| | +--rw named-srlg* [name]
| | ...
| +--rw named-path-constraints
| +--rw named-path-constraint* [name]
named-admin-groups:¶
A YANG container for the list of named (extended) administrative groups that may be applied to TE links.¶
named-srlgs:¶
A YANG container for the list of named Shared Risk Link Groups (SRLGs) that may be applied to TE links.¶
named-path-constraints:¶
A YANG container for a list of named path constraints. Each named path constraint is composed of a set of constraints that can be applied during path computation. A named path constraint can be applied to multiple TE Tunnels. Path constraints may also be specified directly under the TE Tunnel. The path constraints specified under the TE Tunnel take precedence over the path constraints derived from the referenced named path constraint. A named path constraint entry can be formed of the path constraints shown in Figure 4:¶
| +--rw named-path-constraints
| +--rw named-path-constraint* [name]
| {te-types:named-path-constraints}?
| +--rw name string
| +--rw te-bandwidth
| | ...
| +--rw link-protection? identityref
| +--rw setup-priority? uint8
| +--rw hold-priority? uint8
| +--rw signaling-type? identityref
| +--rw path-metric-bounds
| | ...
| +--rw path-affinities-values
| | ...
| +--rw path-affinity-names
| | ...
| +--rw path-srlgs-lists
| | ...
| +--rw path-srlgs-names
| | ...
| +--rw disjointness?
| | te-path-disjointness
| +--rw explicit-route-objects-always
| | ...
| +--rw path-in-segment!
| | ...
| +--rw path-out-segment!
| ...
explicit-route-objects-always: A YANG container that contains two route objects lists:¶
The 'route-object-include-exclude' is used to configure constraints on which route objects (e.g., nodes, links) are included or excluded in the path computation.¶
The interpretation of an empty 'route-object-include-exclude' list depends on the TE Tunnel (end-to-end or Tunnel Segment) and on the specific path, according to the following rules:¶
The 'tunnels' container holds the list of TE Tunnels that are provisioned on devices in the network as shown in Figure 5.¶
+--rw tunnels
| +--rw tunnel* [name]
| +--rw name string
| +--rw alias? string
| +--rw identifier? uint32
| +--rw color? uint32
| +--rw description? string
| +--rw admin-state? identityref
| +--ro operational-state? identityref
| +--rw encoding? identityref
| +--rw switching-type? identityref
| +--rw source? te-types:te-node-id
| +--rw destination? te-types:te-node-id
| +--rw src-tunnel-tp-id? binary
| +--rw dst-tunnel-tp-id? binary
| +--rw bidirectional? boolean
| +--rw controller
| | +--rw protocol-origin? identityref
| | +--rw controller-entity-id? string
| +--rw reoptimize-timer? uint16
| +--rw association-objects
| | +--rw association-object* [association-key]
| | | ...
| | +--rw association-object-extended* [association-key]
| | ...
| +--rw protection
| | +--rw enable? boolean
| | +--rw protection-type? identityref
| | +--rw protection-reversion-disable? boolean
| | +--rw hold-off-time? uint32
| | +--rw wait-to-revert? uint16
| | +--rw aps-signal-id? uint8
| +--rw restoration
| | +--rw enable? boolean
| | +--rw restoration-type? identityref
| | +--rw restoration-scheme? identityref
| | +--rw restoration-reversion-disable? boolean
| | +--rw hold-off-time? uint32
| | +--rw wait-to-restore? uint16
| | +--rw wait-to-revert? uint16
| +--rw te-topology-identifier
| | +--rw provider-id? te-global-id
| | +--rw client-id? te-global-id
| | +--rw topology-id? te-topology-id
| +--rw te-bandwidth
| | +--rw (technology)?
| | ...
| +--rw link-protection? identityref
| +--rw setup-priority? uint8
| +--rw hold-priority? uint8
| +--rw signaling-type? identityref
| +--rw hierarchy
| | +--rw dependency-tunnels
| | | ...
| | +--rw hierarchical-link
| | ...
| +--rw primary-paths
| | +--rw primary-path* [name]
| | ...
| +--rw secondary-paths
| | +--rw secondary-path* [name]
| | ...
| +--rw secondary-reverse-paths
| | +--rw secondary-reverse-path* [name]
| | ...
| +---x tunnel-action
| | +---w input
| | | ...
| | +--ro output
| | ...
| +---x protection-external-commands
| +---w input
| ...
When the model is used to manage a specific device, the 'tunnels' list contains the TE Tunnels originating from the specific device. When the model is used to manage a TE controller, the 'tunnels' list contains all TE Tunnels and TE tunnel segments originating from device(s) that the TE controller manages.¶
The TE Tunnel model allows the configuration and management of the following TE tunnel objects:¶
TE Tunnel:¶
A YANG container of one or more TE LSPs established between the source and destination TE Tunnel termination points.¶
TE Path:¶
An engineered path that once instantiated in the forwarding plane can be used to forward traffic from the source to the destination TE Tunnel termination points.¶
TE LSP:¶
A TE LSP is a connection-oriented service established over a TE Path and that allows the delivery of traffic between the TE Tunnel source and destination termination points.¶
TE Tunnel Segment:¶
A part of a multi-domain TE Tunnel that is within a specific network domain.¶
The TE Tunnel has a number of attributes that are set directly under the tunnel (as shown in Figure 5). The main attributes of a TE Tunnel are described below:¶
operational-state:¶
A YANG leaf that holds the operational state of the tunnel.¶
name:¶
A YANG leaf that holds the name of a TE Tunnel. The name of the TE Tunnel uniquely identifies the tunnel within the TE tunnel list. The name of the TE Tunnel can be formatted as a Uniform Resource Indicator (URI) by including the namespace to ensure uniqueness of the name amongst all the TE Tunnels present on devices and controllers. The configured TE Tunnels can be reported with the name of the device embedded within the TE Tunnel name. For initiated TE Tunnels from the controller, the controller is responsible to ensures that TE Tunnel names are unique.¶
alias:¶
A YANG leaf that holds an alternate name to the TE tunnel. Unlike the TE tunnel name, the alias can be modified at any time during the lifetime of the TE tunnel.¶
identifier:¶
A YANG leaf that holds an identifier of the tunnel. This identifier is unique amongst tunnels originated from the same ingress device.¶
color:¶
A YANG leaf that holds the color associated with the TE tunnel. The color is used to map or steer services that carry matching color on to the TE tunnel as described in [RFC9012].¶
admin-state:¶
A YANG leaf that holds the tunnel administrative state. The administrative status in state datastore transitions to 'tunnel-admin-up' when the tunnel used by the client layer, and to 'tunnel-admin-down' when it is not used by the client layer.¶
operational-state:¶
A YANG leaf that holds the tunnel operational state.¶
encoding/switching:¶
The 'encoding' and 'switching-type' are YANG leafs that define the specific technology in which the tunnel operates in as described in [RFC3945].¶
source/destination:¶
YANG leafs that define the tunnel source and destination node endpoints.¶
src-tunnel-tp-id/dst-tunnel-tp-id:¶
YANG leafs that hold the identifiers of source and destination TE Tunnel Termination Points (TTPs) [RFC8795] residing on the source and destination nodes. The TTP identifiers are optional on nodes that have a single TTP per node. For example, TTP identifiers are optional for packet (IP/MPLS) routers.¶
bidirectional:¶
A YANG leaf that when present indicates the LSP of a TE Tunnel is bidirectional and co-routed as defined in [rfc3473].¶
controller:¶
A YANG container that holds tunnel data relevant to an optional external TE controller that may initiate or control a tunnel. This target node may be augmented by external module(s), for example, to add data for PCEP initiated and/or delegated tunnels.¶
reoptimize-timer:¶
A YANG leaf to set the interval period for tunnel reoptimization.¶
association-objects:¶
A YANG container that holds the set of associations of the TE Tunnel to other TE Tunnels. Associations at the TE Tunnel level apply to all paths of the TE Tunnel. The TE tunnel associations can be overridden by associations configured directly under the TE Tunnel path.¶
protection:¶
A YANG container that holds the TE Tunnel protection properties.¶
restoration:¶
A YANG container that holds the TE Tunnel restoration properties.¶
te-topology-identifier:¶
A YANG container that holds the topology identifier associated with the topology where paths for the TE tunnel are computed.¶
hierarchy:¶
A YANG container that holds hierarchy related properties of the TE Tunnel. A TE LSP can be set up in MPLS or Generalized MPLS (GMPLS) networks to be used as a TE link to carry traffic in other (client) networks [RFC6107]. In this case, the model introduces the TE Tunnel hierarchical link endpoint parameters to identify the specific link in the client layer that the underlying TE Tunnel is associated with. The hierarchy container includes the following:¶
primary-paths:¶
A YANG container that holds the list of primary paths. A primary path is identified by 'name'. A primary path is selected from the list to instantiate a primary forwarding LSP for the tunnel. The list of primary paths is visited by order of preference. A primary path has the following attributes:¶
secondary-paths:¶
A YANG container that holds the set of secondary paths. A secondary path is identified by 'name'. A secondary path can be referenced from the TE Tunnel's 'candidate-secondary-path' list.¶
secondary-reverse-paths:¶
A YANG container that holds the set of secondary reverse paths. A secondary reverse path is identified by 'name'. A secondary reverse path can be referenced from the TE Tunnel's 'candidate-secondary-reverse-paths' list. A secondary reverse path contains attributes similar to a primary path.¶
The following set of common path attributes are shared for primary (forward and reverse) and secondary paths:¶
path-computation-method:¶
A YANG leaf that specifies the method used for computing the TE path.¶
path-computation-server:¶
A YANG container that holds the path computation server properties when the path is externally queried.¶
compute-only:¶
A path of a TE Tunnel is, by default, provisioned so that it can be instantiated in the forwarding plane so that it can carry traffic as soon as a valid path is computed. In some cases, a TE path may be configured only for the purpose of computing a path and reporting it without the need to instantiate the LSP or commit any resources. In such a case, the path is configured in 'compute-only' mode to distinguish it from the default behavior. A 'compute-only' path is configured as a usual with the associated per path constraint(s) and properties on a device or TE controller. The device or TE controller computes the feasible path(s) subject to configured constraints. A client may query the 'compute-only' computed path properties 'on-demand', or alternatively, can subscribe to be notified of computed path(s) and whenever the path properties change.¶
use-path-computation:¶
A YANG leaf that indicates whether or not path computation is to be used for a specified path.¶
lockdown:¶
A YANG leaf that when set indicates the existing path should not be reoptimized after a failure on any of its traversed links.¶
path-scope:¶
A YANG leaf that specifies the path scope if segment or an end-to-end path.¶
preference:¶
A YANG leaf that specifies the preference for the path. The lower the number higher the preference.¶
k-requested-paths:¶
A YANG leaf that specifies the number of k-shortest-paths requested from the path computation server and returned sorted by its optimization objective.¶
association-objects:¶
A YANG container that holds a list of tunnel association properties.¶
optimizations:¶
A YANG container that holds the optimization objectives that path computation will use to select a path.¶
named-path-constraint:¶
A YANG leafref that references an entry from the global list of named path constraints.¶
te-bandwidth:¶
link-protection:¶
A YANG leaf that specifies the link protection type required for the links to be included the computed path (see [RFC8776]).¶
setup/hold-priority:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
signaling-type:¶
see description provided in Section 5.1.1. This value overrides the provided one in the referenced named-path-constraint.¶
path-metric-bounds:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
path-affinities-values:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
path-affinity-names:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
path-srlgs-lists:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
path-srlgs-names:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
disjointness:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
explicit-route-objects-always:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
path-in-segment:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
path-out-segment:¶
see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint.¶
computed-paths-properties:¶
A YANG container that holds properties for the list of computed paths.¶
computed-path-error-infos:¶
A YANG container that holds a list of errors related to the path.¶
lsp-provisioning-error-infos:¶
A YANG container that holds the list of LSP provisioning error information.¶
lsps:¶
A YANG container that holds a list of LSPs that have been instantiated for this specific path.¶
In addition to the path common attributes, the primary path has the following attributes that are not present in the secondary path:¶
The 'lsps' container includes the set of TE LSP(s) that have been instantiated. A TE LSP is identified by a 3-tuple ('tunnel-name', 'lsp-id', 'node').¶
When the model is used to manage a specific device, the 'lsps' list contains all TE LSP(s) that traverse the device (including ingressing, transiting and egressing the device).¶
When the model is used to manage a TE controller, the 'lsps' list contains all TE LSP(s) that traverse all network devices (including ingressing, transiting and egressing the device) that the TE controller manages.¶
Figure 6 shows the tree diagram of depth=4 for the generic TE YANG model defined in modules 'ietf-te.yang'. The full tree diagram is shown in Section 13.¶
module: ietf-te
+--rw te
+--rw enable? boolean
+--rw globals
| +--rw named-admin-groups
| | +--rw named-admin-group* [name]
| | {te-types:extended-admin-groups,
| | te-types:named-extended-admin-groups}?
| | ...
| +--rw named-srlgs
| | +--rw named-srlg* [name] {te-types:named-srlg-groups}?
| | ...
| +--rw named-path-constraints
| +--rw named-path-constraint* [name]
| {te-types:named-path-constraints}?
| ...
+--rw tunnels
| +--rw tunnel* [name]
| +--rw name string
| +--rw alias? string
| +--rw identifier? uint32
| +--rw color? uint32
| +--rw description? string
| +--rw admin-state? identityref
| +--ro operational-state? identityref
| +--rw encoding? identityref
| +--rw switching-type? identityref
| +--rw source? te-types:te-node-id
| +--rw destination? te-types:te-node-id
| +--rw src-tunnel-tp-id? binary
| +--rw dst-tunnel-tp-id? binary
| +--rw bidirectional? boolean
| +--rw controller
| | ...
| +--rw reoptimize-timer? uint16
| +--rw association-objects
| | ...
| +--rw protection
| | ...
| +--rw restoration
| | ...
| +--rw te-topology-identifier
| | ...
| +--rw te-bandwidth
| | ...
| +--rw link-protection? identityref
| +--rw setup-priority? uint8
| +--rw hold-priority? uint8
| +--rw signaling-type? identityref
| +--rw hierarchy
| | ...
| +--rw primary-paths
| | ...
| +--rw secondary-paths
| | ...
| +--rw secondary-reverse-paths
| | ...
| +---x tunnel-action
| | ...
| +---x protection-external-commands
| ...
+--ro lsps
+--ro lsp* [tunnel-name lsp-id node]
+--ro tunnel-name string
+--ro lsp-id uint16
+--ro node
| te-types:te-node-id
+--ro source?
| te-types:te-node-id
+--ro destination?
| te-types:te-node-id
+--ro tunnel-id? uint16
+--ro extended-tunnel-id?
| yang:dotted-quad
+--ro operational-state? identityref
+--ro signaling-type? identityref
+--ro origin-type? enumeration
+--ro lsp-resource-status? enumeration
+--ro lockout-of-normal? boolean
+--ro freeze? boolean
+--ro lsp-protection-role? enumeration
+--ro lsp-protection-state? identityref
+--ro protection-group-ingress-node-id?
| te-types:te-node-id
+--ro protection-group-egress-node-id?
| te-types:te-node-id
+--ro lsp-actual-route-information
...
rpcs:
+---x tunnels-path-compute
| +---w input
| | +---w path-compute-info
| +--ro output
| +--ro path-compute-result
+---x tunnels-actions
+---w input
| +---w tunnel-info
| | +---w (filter-type)
| | ...
| +---w action-info
| +---w action? identityref
| +---w disruptive? empty
+--ro output
+--ro action-result? identityref
The generic TE YANG module 'ietf-te' imports the following modules:¶
This module references the following documents: [RFC4206], [RFC4427], [RFC4872], [RFC3209], [RFC6780], [RFC7471], [RFC9012], [RFC8570], [RFC8232], [RFC7271], [RFC8234], [RFC7308], and [ITU_G.808.1].¶
<CODE BEGINS> file "ietf-te@2023-03-11.yang"
module ietf-te {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-te";
/* Replace with IANA when assigned */
prefix te;
/* Import TE generic types */
import ietf-te-types {
prefix te-types;
reference
"RFC8776: Common YANG Data Types for Traffic Engineering.";
}
import ietf-inet-types {
prefix inet;
reference
"RFC6991: Common YANG Data Types.";
}
import ietf-yang-types {
prefix yang;
reference
"RFC6991: Common YANG Data Types.";
}
organization
"IETF Traffic Engineering Architecture and Signaling (TEAS)
Working Group.";
contact
"WG Web: <https://tools.ietf.org/wg/teas/>
WG List: <mailto:teas@ietf.org>
Editor: Tarek Saad
<mailto:tsaad.net@gmail.com>
Editor: Rakesh Gandhi
<mailto:rgandhi@cisco.com>
Editor: Vishnu Pavan Beeram
<mailto:vbeeram@juniper.net>
Editor: Himanshu Shah
<mailto:hshah@ciena.com>
Editor: Xufeng Liu
<mailto: xufeng.liu.ietf@gmail.com>
Editor: Igor Bryskin
<mailto:i_bryskin@yahoo.com>";
description
"YANG data module for TE configuration, state, and RPCs.
The model fully conforms to the Network Management
Datastore Architecture (NMDA).
Copyright (c) 2023 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject to
the license terms contained in, the Revised BSD License set
forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX
(https://www.rfc-editor.org/info/rfcXXXX); see the RFC itself
for full legal notices.";
// RFC Ed.: replace XXXX with actual RFC number and remove this
// note.
// RFC Ed.: update the date below with the date of RFC publication
// and remove this note.
revision 2023-03-11 {
description
"Initial revision for the TE generic YANG module.";
reference
"RFCXXXX: A YANG Data Model for Traffic Engineering Tunnels
and Interfaces.";
}
typedef tunnel-ref {
type leafref {
path "/te:te/te:tunnels/te:tunnel/te:name";
}
description
"This type is used by data models that need to reference
configured TE tunnel.";
}
typedef te-gen-node-id {
type union {
type te-types:te-node-id;
type inet:ip-address;
}
description
"Generic type that identifies a node in a TE topology.";
}
/**
* TE tunnel generic groupings
*/
grouping te-generic-node-id {
description
"A reusable grouping for a TE generic node identifier.";
leaf id {
type te-gen-node-id;
description
"The identifier of the node. Can be represented as IP
address or dotted quad address.";
}
leaf type {
type enumeration {
enum ip {
description
"IP address representation of the node identifier.";
}
enum dotted-quad {
description
"Dotted quad address representation of the node
identifier.";
}
}
description
"Type of node identifier representation.";
}
}
grouping path-common-properties {
description
"Common path attributes.";
leaf name {
type string;
description
"TE path name.";
}
leaf path-computation-method {
type identityref {
base te-types:path-computation-method;
}
default "te-types:path-locally-computed";
description
"The method used for computing the path, either
locally computed, queried from a server or not
computed at all (explicitly configured).";
}
container path-computation-server {
when "derived-from-or-self(../path-computation-method, "
+ "'te-types:path-externally-queried')" {
description
"The path-computation server when the path is
externally queried.";
}
uses te-generic-node-id;
description
"Address of the external path computation
server.";
}
leaf compute-only {
type empty;
description
"When present, the path is computed and updated whenever
the topology is updated. No resources are committed
or reserved in the network.";
}
leaf use-path-computation {
when "derived-from-or-self(../path-computation-method, "
+ "'te-types:path-locally-computed')";
type boolean;
default "true";
description
"When 'true' indicates the path is dynamically computed
and/or validated against the Traffic-Engineering Database
(TED), and when 'false' indicates no path expansion or
validation against the TED is required.";
}
leaf lockdown {
type empty;
description
"When present, indicates no reoptimization to be attempted
for this path.";
}
leaf path-scope {
type identityref {
base te-types:path-scope-type;
}
default "te-types:path-scope-end-to-end";
config false;
description
"Indicates whether the path is a segment or portion of
of the full path., or is the an end-to-end path for
the TE Tunnel.";
}
}
/* This grouping is re-used in path-computation rpc */
grouping path-compute-info {
description
"Attributes used for path computation request.";
uses tunnel-associations-properties;
uses te-types:generic-path-optimization;
leaf named-path-constraint {
if-feature "te-types:named-path-constraints";
type leafref {
path "/te:te/te:globals/te:named-path-constraints/"
+ "te:named-path-constraint/te:name";
}
description
"Reference to a globally defined named path constraint set.";
}
uses path-constraints-common;
}
/* This grouping is re-used in path-computation rpc */
grouping path-forward-properties {
description
"The path preference.";
leaf preference {
type uint8 {
range "1..255";
}
default "1";
description
"Specifies a preference for this path. The lower the number
higher the preference.";
}
leaf co-routed {
when "/te:te/te:tunnels/te:tunnel/te:bidirectional = 'true'" {
description
"Applicable to bidirectional tunnels only.";
}
type boolean;
default "false";
description
"Indicates whether the reverse path must to be co-routed
with the primary.";
}
}
/* This grouping is re-used in path-computation rpc */
grouping k-requested-paths {
description
"The k-shortest paths requests.";
leaf k-requested-paths {
type uint8;
default "1";
description
"The number of k-shortest-paths requested from the path
computation server and returned sorted by its optimization
objective.";
}
}
grouping path-state {
description
"TE per path state parameters.";
uses path-computation-response;
container lsp-provisioning-error-infos {
config false;
description
"LSP provisioning error information.";
list lsp-provisioning-error-info {
description
"List of LSP provisioning error info entries.";
leaf error-reason {
type identityref {
base te-types:lsp-provisioning-error-reason;
}
description
"LSP provision error type.";
}
leaf error-description {
type string;
description
"The textual representation of the error occurred during
path computation.";
}
leaf error-timestamp {
type yang:date-and-time;
description
"Timestamp of when the reported error occurred.";
}
leaf error-node-id {
type te-types:te-node-id;
description
"Node identifier of node where error occurred.";
}
leaf error-link-id {
type te-types:te-tp-id;
description
"Link ID where the error occurred.";
}
leaf lsp-id {
type uint16;
description
"The LSP-ID for which path computation was performed.";
}
}
}
container lsps {
config false;
description
"The TE LSPs container.";
list lsp {
key "node lsp-id";
description
"List of LSPs associated with the tunnel.";
leaf tunnel-name {
type leafref {
path "/te:te/te:lsps/te:lsp/te:tunnel-name";
}
description "TE tunnel name.";
}
leaf node {
type leafref {
path "/te:te/te:lsps/te:lsp[tunnel-name="
+ "current()/../te:tunnel-name][lsp-id="
+ "current()/../te:lsp-id]/te:node";
}
description "The node where the LSP state resides on.";
}
leaf lsp-id {
type leafref {
path "/te:te/te:lsps/te:lsp[tunnel-name="
+ "current()/../tunnel-name]/te:lsp-id";
}
description "The TE LSP identifier.";
}
}
}
}
/* This grouping is re-used in path-computation rpc */
grouping path-computation-response {
description
"Attributes reported by path computation response.";
container computed-paths-properties {
config false;
description
"Computed path properties container.";
list computed-path-properties {
key "k-index";
description
"List of computed paths.";
leaf k-index {
type uint8;
description
"The k-th path returned from the computation server.
A lower k value path is more optimal than higher k
value path(s)";
}
uses te-types:generic-path-properties {
augment "path-properties" {
description
"additional path properties returned by path
computation.";
uses te-types:te-bandwidth;
leaf disjointness-type {
type te-types:te-path-disjointness;
config false;
description
"The type of resource disjointness.
When reported for a primary path, it represents the
minimum level of disjointness of all the secondary
paths. When reported for a secondary path, it
represents the disjointness of the secondary path.";
}
}
}
}
}
container computed-path-error-infos {
config false;
description
"Path computation information container.";
list computed-path-error-info {
description
"List of path computation info entries.";
leaf error-description {
type string;
description
"Textual representation of the error occurred during
path computation.";
}
leaf error-timestamp {
type yang:date-and-time;
description
"Timestamp of last path computation attempt.";
}
leaf error-reason {
type identityref {
base te-types:path-computation-error-reason;
}
description
"Reason for the path computation error.";
}
}
}
}
grouping protection-restoration-properties {
description
"Protection and restoration parameters.";
container protection {
description
"Protection parameters.";
leaf protection-type {
type identityref {
base te-types:lsp-protection-type;
}
default "te-types:lsp-protection-unprotected";
description
"LSP protection type.";
}
leaf protection-reversion-disable {
type boolean;
default "false";
description
"Disable protection reversion to working path.";
}
leaf hold-off-time {
type uint32;
units "milli-seconds";
description
"The time between the declaration of an SF or SD condition
and the initialization of the protection switching
algorithm.";
reference
"RFC4427";
}
leaf wait-to-revert {
type uint16;
units "seconds";
description
"Time to wait before attempting LSP reversion.";
reference
"RFC4427";
}
leaf aps-signal-id {
type uint8 {
range "1..255";
}
default "1";
description
"The APS signal number used to reference the traffic of
this tunnel. The default value for normal traffic is 1.
The default value for extra-traffic is 255. If not
specified, non-default values can be assigned by the
server, if and only if, the server controls both
endpoints.";
reference
"RFC4427";
}
}
container restoration {
description
"Restoration parameters.";
leaf restoration-type {
type identityref {
base te-types:lsp-restoration-type;
}
default "te-types:lsp-restoration-restore-none";
description
"LSP restoration type.";
}
leaf restoration-scheme {
type identityref {
base te-types:restoration-scheme-type;
}
default "te-types:restoration-scheme-preconfigured";
description
"LSP restoration scheme.";
}
leaf restoration-reversion-disable {
type boolean;
default "false";
description
"Disable restoration reversion to working path.";
}
leaf hold-off-time {
type uint32;
units "milli-seconds";
description
"The time between the declaration of an SF or SD condition
and the initialization of the protection switching
algorithm.";
reference
"RFC4427";
}
leaf wait-to-restore {
type uint16;
units "seconds";
description
"Time to wait before attempting LSP restoration.";
reference
"RFC4427";
}
leaf wait-to-revert {
type uint16;
units "seconds";
description
"Time to wait before attempting LSP reversion.";
reference
"RFC4427";
}
}
}
grouping tunnel-associations-properties {
description
"TE tunnel association grouping.";
container association-objects {
description
"TE tunnel associations.";
list association-object {
key "association-key";
unique "type id source/id source/type";
description
"List of association base objects.";
reference
"RFC4872";
leaf association-key {
type string;
description
"Association key used to identify a specific
association in the list";
}
leaf type {
type identityref {
base te-types:association-type;
}
description
"Association type.";
reference
"RFC4872";
}
leaf id {
type uint16;
description
"Association identifier.";
reference
"RFC4872";
}
container source {
uses te-generic-node-id;
description
"Association source.";
reference
"RFC4872";
}
}
list association-object-extended {
key "association-key";
unique
"type id source/id source/type global-source extended-id";
description
"List of extended association objects.";
reference
"RFC6780";
leaf association-key {
type string;
description
"Association key used to identify a specific
association in the list";
}
leaf type {
type identityref {
base te-types:association-type;
}
description
"Association type.";
reference
"RFC4872, RFC6780";
}
leaf id {
type uint16;
description
"Association identifier.";
reference
"RFC4872, RFC6780";
}
container source {
uses te-generic-node-id;
description
"Association source.";
reference
"RFC4872, RFC6780";
}
leaf global-source {
type uint32;
description
"Association global source.";
reference
"RFC6780";
}
leaf extended-id {
type yang:hex-string;
description
"Association extended identifier.";
reference
"RFC6780";
}
}
}
}
/* This grouping is re-used in path-computation rpc */
grouping tunnel-common-attributes {
description
"Common grouping to define the TE tunnel parameters";
leaf source {
type te-types:te-node-id;
description
"TE tunnel source node ID.";
}
leaf destination {
type te-types:te-node-id;
description
"TE tunnel destination node identifier.";
}
leaf src-tunnel-tp-id {
type binary;
description
"TE tunnel source termination point identifier.";
}
leaf dst-tunnel-tp-id {
type binary;
description
"TE tunnel destination termination point identifier.";
}
leaf bidirectional {
type boolean;
default "false";
description
"Indicates a bidirectional co-routed LSP (non-associated
LSP case).";
}
}
/* This grouping is re-used in path-computation rpc */
grouping tunnel-hierarchy-properties {
description
"A grouping for TE tunnel hierarchy information.";
container hierarchy {
description
"Container for TE hierarchy related information.";
container dependency-tunnels {
description
"List of tunnels that this tunnel can be potentially
dependent on.";
list dependency-tunnel {
key "name";
description
"A tunnel entry that this tunnel can potentially depend
on.";
leaf name {
type leafref {
path "/te:te/te:tunnels/te:tunnel/te:name";
require-instance false;
}
description
"Dependency tunnel name. The tunnel may not have been
instantiated yet.";
}
uses te-types:encoding-and-switching-type;
}
}
container hierarchical-link {
description
"Identifies a hierarchical link (in client layer)
that this tunnel is associated with. By default, the
topology of the hierarchical link is the same topology of
the tunnel;";
reference
"RFC4206";
leaf enable {
type boolean;
description
"Enables the hierarchical link properties supported by
this tunnel";
}
leaf local-te-node-id {
type te-types:te-node-id;
description
"The local TE node identifier.";
}
leaf local-te-link-tp-id {
type te-types:te-tp-id;
description
"The local TE link termination point identifier.";
}
leaf remote-te-node-id {
type te-types:te-node-id;
description
"Remote TE node identifier.";
}
uses te-types:te-topology-identifier {
description
"The topology identifier where the hierarchical link
supported by this TE tunnel is instantiated.";
}
}
}
}
grouping path-constraints-common {
description
"Global named path constraints configuration
grouping.";
uses te-types:common-path-constraints-attributes {
description
"The constraints applicable to the path. This includes:
- The path bandwidth constraint
- The path link protection type constraint
- The path setup/hold priority constraint
- path signaling type constraint
- path metric bounds constraint. The unit of path metric
bound is interpreted in the context of the metric-type.
For example for metric-type 'path-metric-loss', the bound
is multiples of the basic unit 0.000003% as described
in RFC7471 for OSPF, and RFC8570 for ISIS.
- path affinity constraints
- path SRLG constraints";
}
uses te-types:generic-path-disjointness;
uses te-types:path-constraints-route-objects;
container path-in-segment {
presence "The end-to-end tunnel starts in a previous domain;
this tunnel is a segment in the current domain.";
description
"If an end-to-end tunnel crosses multiple domains using
the same technology, some additional constraints have to be
taken in consideration in each domain.
This TE tunnel segment is stitched to the upstream TE tunnel
segment.";
uses te-types:label-set-info;
}
container path-out-segment {
presence
"The end-to-end tunnel is not terminated in this domain;
this tunnel is a segment in the current domain.";
description
"If an end-to-end tunnel crosses multiple domains using
the same technology, some additional constraints have to be
taken in consideration in each domain.
This TE tunnel segment is stitched to the downstream TE
tunnel segment.";
uses te-types:label-set-info;
}
}
/**
* TE container
*/
container te {
description
"TE global container.";
leaf enable {
type boolean;
default "false";
description
"Enables the TE component features.";
}
/* TE Global Data */
container globals {
description
"Globals TE system-wide configuration data container.";
container named-admin-groups {
description
"TE named admin groups container.";
list named-admin-group {
if-feature "te-types:extended-admin-groups";
if-feature "te-types:named-extended-admin-groups";
key "name";
description
"List of named TE admin-groups.";
leaf name {
type string;
description
"A string name that uniquely identifies a TE
interface named admin-group.";
}
leaf bit-position {
type uint32;
description
"Bit position representing the administrative group.";
reference
"RFC3209 and RFC7308";
}
}
}
container named-srlgs {
description
"TE named SRLGs container.";
list named-srlg {
if-feature "te-types:named-srlg-groups";
key "name";
description
"A list of named SRLG groups.";
leaf name {
type string;
description
"A string name that uniquely identifies a TE
interface named SRLG.";
}
leaf value {
type te-types:srlg;
description
"An SRLG value.";
}
leaf cost {
type uint32;
description
"SRLG associated cost. Used during path to append
the path cost when traversing a link with this SRLG.";
}
}
}
container named-path-constraints {
description
"TE named path constraints container.";
list named-path-constraint {
if-feature "te-types:named-path-constraints";
key "name";
leaf name {
type string;
description
"A string name that uniquely identifies a
path constraint set.";
}
uses path-constraints-common;
description
"A list of named path constraints.";
}
}
}
/* TE Tunnel Data */
container tunnels {
description
"Tunnels TE configuration data container.";
list tunnel {
key "name";
description
"The list of TE tunnels.";
leaf name {
type string;
description
"TE tunnel name.";
}
leaf alias {
type string;
description
"An alternate name of the TE tunnel that can be modified
anytime during its lifetime.";
}
leaf identifier {
type uint32;
description
"TE tunnel Identifier.";
reference
"RFC3209";
}
leaf color {
type uint32;
description "The color associated with the TE tunnel.";
reference "RFC9012";
}
leaf description {
type string;
default "None";
description
"Textual description for this TE tunnel.";
}
leaf admin-state {
type identityref {
base te-types:tunnel-admin-state-type;
}
default "te-types:tunnel-admin-state-up";
description
"TE tunnel administrative state.";
}
leaf operational-state {
type identityref {
base te-types:tunnel-state-type;
}
config false;
description
"TE tunnel operational state.";
}
uses te-types:encoding-and-switching-type;
uses tunnel-common-attributes;
container controller {
description
"Contains tunnel data relevant to external controller(s).
This target node may be augmented by external module(s),
for example, to add data for PCEP initiated and/or
delegated tunnels.";
leaf protocol-origin {
type identityref {
base te-types:protocol-origin-type;
}
description
"The protocol origin for instantiating the tunnel.";
}
leaf controller-entity-id {
type string;
description
"An identifier unique within the scope of visibility
that associated with the entity that controls the
tunnel.";
reference "RFC8232";
}
}
leaf reoptimize-timer {
type uint16;
units "seconds";
description
"Frequency of reoptimization of a traffic engineered
LSP.";
}
uses tunnel-associations-properties;
uses protection-restoration-properties;
uses te-types:tunnel-constraints;
uses tunnel-hierarchy-properties;
container primary-paths {
description
"The set of primary paths.";
reference "RFC4872";
list primary-path {
key "name";
description
"List of primary paths for this tunnel.";
uses path-common-properties;
uses path-forward-properties;
uses k-requested-paths;
uses path-compute-info;
uses path-state;
container primary-reverse-path {
when "../../../te:bidirectional = 'false'";
description
"The reverse primary path properties.";
uses path-common-properties;
uses path-compute-info;
uses path-state;
container candidate-secondary-reverse-paths {
when "../../../../te:bidirectional = 'false'";
description
"The set of referenced candidate reverse secondary
paths from the full set of secondary reverse paths
which may be used for this primary path.";
list candidate-secondary-reverse-path {
key "secondary-path";
ordered-by user;
description
"List of candidate secondary reverse path(s)";
leaf secondary-path {
type leafref {
path "../../../../../../"
+ "te:secondary-reverse-paths/"
+ "te:secondary-reverse-path/te:name";
}
description
"A reference to the secondary reverse path that
should be utilised when the containing primary
reverse path option is in use.";
}
}
}
}
container candidate-secondary-paths {
description
"The set of candidate secondary paths which may be
used for this primary path. When secondary paths are
specified in the list the path of the secondary LSP
in use must be restricted to those path options
referenced.
The priority of the secondary paths is specified
within the list. Higher priority values are less
preferred - that is to say that a path with priority
0 is the most preferred path. In the case that the
list is empty, any secondary path option may be
utilised when the current primary path is in use.";
list candidate-secondary-path {
key "secondary-path";
ordered-by user;
description
"List of candidate secondary paths for this
tunnel.";
leaf secondary-path {
type leafref {
path "../../../../../te:secondary-paths/"
+ "te:secondary-path/te:name";
}
description
"A reference to the secondary path that should be
utilised when the containing primary path option
is
in use.";
}
leaf active {
type boolean;
config false;
description
"Indicates the current active path option that
has been selected of the candidate secondary
paths.";
}
}
}
}
}
container secondary-paths {
description
"The set of secondary paths.";
reference "RFC4872";
list secondary-path {
key "name";
description
"List of secondary paths for this tunnel.";
uses path-common-properties;
leaf preference {
type uint8 {
range "1..255";
}
default "1";
description
"Specifies a preference for this path. The lower the
number higher the preference.";
}
uses path-compute-info;
uses protection-restoration-properties;
uses path-state;
}
}
container secondary-reverse-paths {
description
"The set of secondary reverse paths.";
list secondary-reverse-path {
key "name";
description
"List of secondary paths for this tunnel.";
uses path-common-properties;
leaf preference {
type uint8 {
range "1..255";
}
default "1";
description
"Specifies a preference for this path. The lower the
number higher the preference. Paths that have the
same preference will be activated together.";
}
uses path-compute-info;
uses protection-restoration-properties;
uses path-state;
}
}
action tunnel-action {
description
"Tunnel action.";
input {
leaf action-type {
type identityref {
base te-types:tunnel-action-type;
}
description
"Tunnel action type.";
}
}
output {
leaf action-result {
type identityref {
base te-types:te-action-result;
}
description
"The result of the tunnel action operation.";
}
}
}
action protection-external-commands {
input {
leaf protection-external-command {
type identityref {
base te-types:protection-external-commands;
}
description
"Protection external command.";
}
leaf protection-group-ingress-node {
type boolean;
default "true";
description
"When 'true', indicates that the action is
applied on ingress node.
By default, the action applies to the ingress node
only.";
}
leaf protection-group-egress-node {
type boolean;
default "false";
description
"When set to 'true', indicates that the action is
applied on egress node.
By default, the action applies to the ingress node
only.";
}
leaf path-name {
type string;
description
"The name of the path that the external command
applies to.";
}
leaf path-type {
type te-types:path-type;
description
"The type of the path that the external command
applies to.";
}
leaf traffic-type {
type enumeration {
enum normal-traffic {
description
"The manual-switch or forced-switch command
applies to the normal traffic (this Tunnel).";
}
enum null-traffic {
description
"The manual-switch or forced-switch command
applies to the null traffic.";
}
enum extra-traffic {
description
"The manual-switch or forced-switch command
applies to the extra traffic (the extra-traffic
Tunnel sharing protection bandwidth with this
Tunnel).";
}
}
description
"Indicates whether the manual-switch or forced-switch
commands applies to the normal traffic, the null
traffic or the extra-traffic.";
reference
"RFC4427";
}
leaf extra-traffic-tunnel-ref {
type tunnel-ref;
description
"In case there are multiple extra-traffic tunnels
sharing protection bandwidth with this Tunnel
(m:n protection), represents which extra-traffic
Tunnel the manual-switch or forced-switch to
extra-traffic command applies to.";
}
}
}
}
}
/* TE LSPs Data */
container lsps {
config false;
description
"TE LSPs state container.";
list lsp {
key "tunnel-name lsp-id node";
unique "source destination tunnel-id lsp-id "
+ "extended-tunnel-id";
description
"List of LSPs associated with the tunnel.";
leaf tunnel-name {
type string;
description "The TE tunnel name.";
}
leaf lsp-id {
type uint16;
description
"Identifier used in the SENDER_TEMPLATE and the
FILTER_SPEC that can be changed to allow a sender to
share resources with itself.";
reference
"RFC3209";
}
leaf node {
type te-types:te-node-id;
description
"The node where the TE LSP state resides on.";
}
leaf source {
type te-types:te-node-id;
description
"Tunnel sender address extracted from
SENDER_TEMPLATE object.";
reference
"RFC3209";
}
leaf destination {
type te-types:te-node-id;
description
"The tunnel endpoint address.";
reference
"RFC3209";
}
leaf tunnel-id {
type uint16;
description
"The tunnel identifier that remains
constant over the life of the tunnel.";
reference
"RFC3209";
}
leaf extended-tunnel-id {
type yang:dotted-quad;
description
"The LSP Extended Tunnel ID.";
reference
"RFC3209";
}
leaf operational-state {
type identityref {
base te-types:lsp-state-type;
}
description
"The LSP operational state.";
}
leaf signaling-type {
type identityref {
base te-types:path-signaling-type;
}
description
"The signaling protocol used to set up this LSP.";
}
leaf origin-type {
type enumeration {
enum ingress {
description
"Origin ingress.";
}
enum egress {
description
"Origin egress.";
}
enum transit {
description
"Origin transit.";
}
}
description
"The origin of the LSP relative to the location of the
local switch in the path.";
}
leaf lsp-resource-status {
type enumeration {
enum primary {
description
"A primary LSP is a fully established LSP for which
the resource allocation has been committed at the
data plane.";
}
enum secondary {
description
"A secondary LSP is an LSP that has been provisioned
in the control plane only; e.g. resource allocation
has not been committed at the data plane.";
}
}
description
"LSP resource allocation state.";
reference
"RFC4872, section 4.2.1";
}
leaf lockout-of-normal {
type boolean;
description
"When set to 'true', it represents a lockout of normal
traffic external command. When set to 'false', it
represents a clear lockout of normal traffic external
command. The lockout of normal traffic command applies
to this Tunnel.";
reference
"RFC4427";
}
leaf freeze {
type boolean;
description
"When set to 'true', it represents a freeze external
command. When set to 'false', it represents a clear
freeze external command. The freeze command applies to
all the Tunnels which are sharing the protection
resources with this Tunnel.";
reference
"RFC4427";
}
leaf lsp-protection-role {
type enumeration {
enum working {
description
"A working LSP must be a primary LSP whilst a
protecting LSP can be either a primary or a
secondary LSP. Also, known as protected LSPs when
working LSPs are associated with protecting LSPs.";
}
enum protecting {
description
"A secondary LSP is an LSP that has been provisioned
in the control plane only; e.g. resource allocation
has not been committed at the data plane.";
}
}
description
"LSP role type.";
reference
"RFC4872, section 4.2.1";
}
leaf lsp-protection-state {
type identityref {
base te-types:lsp-protection-state;
}
description
"The APS state machine controlling which
tunnels are using the resources of the protecting LSP.";
reference
"ITU_G.808.1, RFC7271, and RFC8234";
}
leaf protection-group-ingress-node-id {
type te-types:te-node-id;
description
"Indicates the te-node-id of the protection group
ingress node when the APS state represents an external
command (LoP, SF, MS) applied to it or a WTR timer
running on it. If the external command is not applied to
the ingress node or the WTR timer is not running on it,
this attribute is not specified. A value 0.0.0.0 is used
when the te-node-id of the protection group ingress node
is unknown (e.g., because the ingress node is outside
the scope of control of the server)";
}
leaf protection-group-egress-node-id {
type te-types:te-node-id;
description
"Indicates the te-node-id of the protection group egress
node when the APS state represents an external command
(LoP, SF, MS) applied to it or a WTR timer running on
it. If the external command is not applied to the
ingress node or the WTR timer is not running on it, this
attribute is not specified. A value 0.0.0.0 is used when
the te-node-id of the protection group ingress node is
unknown (e.g., because the ingress node is outside the
scope of control of the server)";
}
container lsp-actual-route-information {
description
"RSVP recorded route object information.";
list lsp-actual-route-information {
when "../../origin-type = 'ingress'" {
description
"Applicable on ingress LSPs only.";
}
key "index";
description
"Record route list entry.";
uses te-types:record-route-state;
}
}
}
}
}
/* TE Tunnel RPCs/execution Data */
rpc tunnels-path-compute {
description
"TE tunnels RPC nodes.";
input {
container path-compute-info {
/*
* An external path compute module may augment this
* target.
*/
description
"RPC input information.";
}
}
output {
container path-compute-result {
/*
* An external path compute module may augment this
* target.
*/
description
"RPC output information.";
}
}
}
rpc tunnels-actions {
description
"TE tunnels actions RPC";
input {
container tunnel-info {
description
"TE tunnel information.";
choice filter-type {
mandatory true;
description
"Filter choice.";
case all-tunnels {
leaf all {
type empty;
mandatory true;
description
"When present, applies the action on all TE
tunnels.";
}
}
case one-tunnel {
leaf tunnel {
type tunnel-ref;
description
"Apply action on the specific TE tunnel.";
}
}
}
}
container action-info {
description
"TE tunnel action information.";
leaf action {
type identityref {
base te-types:tunnel-action-type;
}
description
"The action type.";
}
leaf disruptive {
when "derived-from-or-self(../action, "
+ "'te-types:tunnel-action-reoptimize')";
type empty;
description
"When present, specifies whether or not the
reoptimization
action is allowed to be disruptive.";
}
}
}
output {
leaf action-result {
type identityref {
base te-types:te-action-result;
}
description
"The result of the tunnel action operation.";
}
}
}
}
<CODE ENDS>
The device TE YANG module ('ietf-te-device') models data that is specific to managing a TE device. This module augments the generic TE YANG module.¶
This branch of the model manages TE interfaces that are present on a device. Examples of TE interface properties are:¶
Flooding parameters¶
Interface attributes¶
The derived state associated with interfaces is grouped under the interface "state" sub-container as shown in Figure 8. This covers state data such as:¶
List of admitted LSPs¶
Adjacency information¶
module: ietf-te-device
augment /te:te:
+--rw interfaces
.
+-- rw te-dev:te-attributes
<<intended configuration>>
.
+-- ro state
<<derived state associated with the TE interface>>
Figure 9 shows the tree diagram of the device TE YANG model defined in modules 'ietf-te-device.yang'.¶
module: ietf-te-device
augment /te:te:
+--rw interfaces
+--rw threshold-type? enumeration
+--rw delta-percentage? rt-types:percentage
+--rw threshold-specification? enumeration
+--rw up-thresholds* rt-types:percentage
+--rw down-thresholds* rt-types:percentage
+--rw up-down-thresholds* rt-types:percentage
+--rw interface* [interface]
+--rw interface if:interface-ref
+--rw te-metric?
| te-types:te-metric
+--rw (admin-group-type)?
| +--:(value-admin-groups)
| | +--rw (value-admin-group-type)?
| | +--:(admin-groups)
| | | +--rw admin-group?
| | | te-types:admin-group
| | +--:(extended-admin-groups)
| | {te-types:extended-admin-groups}?
| | +--rw extended-admin-group?
| | te-types:extended-admin-group
| +--:(named-admin-groups)
| +--rw named-admin-groups* [named-admin-group]
| {te-types:extended-admin-groups,
| te-types:named-extended-admin-groups}?
| +--rw named-admin-group leafref
+--rw (srlg-type)?
| +--:(value-srlgs)
| | +--rw values* [value]
| | +--rw value uint32
| +--:(named-srlgs)
| +--rw named-srlgs* [named-srlg]
| {te-types:named-srlg-groups}?
| +--rw named-srlg leafref
+--rw threshold-type? enumeration
+--rw delta-percentage?
| rt-types:percentage
+--rw threshold-specification? enumeration
+--rw up-thresholds*
| rt-types:percentage
+--rw down-thresholds*
| rt-types:percentage
+--rw up-down-thresholds*
| rt-types:percentage
+--rw switching-capabilities* [switching-capability]
| +--rw switching-capability identityref
| +--rw encoding? identityref
+--ro te-advertisements-state
+--ro flood-interval? uint32
+--ro last-flooded-time? uint32
+--ro next-flooded-time? uint32
+--ro last-flooded-trigger? enumeration
+--ro advertised-level-areas* [level-area]
+--ro level-area uint32
augment /te:te/te:globals:
+--rw lsp-install-interval? uint32
+--rw lsp-cleanup-interval? uint32
+--rw lsp-invalidation-interval? uint32
augment /te:te/te:tunnels/te:tunnel:
+--rw path-invalidation-action? identityref
+--rw lsp-install-interval? uint32
+--rw lsp-cleanup-interval? uint32
+--rw lsp-invalidation-interval? uint32
augment /te:te/te:lsps/te:lsp:
+--ro lsp-timers
| +--ro uptime? uint32
| +--ro time-to-install? uint32
| +--ro time-to-destroy? uint32
+--ro downstream-info
| +--ro nhop? te-types:te-tp-id
| +--ro outgoing-interface? if:interface-ref
| +--ro neighbor
| | +--ro id? te-gen-node-id
| | +--ro type? enumeration
| +--ro label? rt-types:generalized-label
+--ro upstream-info
+--ro phop? te-types:te-tp-id
+--ro neighbor
| +--ro id? te-gen-node-id
| +--ro type? enumeration
+--ro label? rt-types:generalized-label
rpcs:
+---x link-state-update
+---w input
+---w (filter-type)
+--:(match-all)
| +---w all empty
+--:(match-one-interface)
+---w interface? if:interface-ref
The device TE YANG module 'ietf-te-device' imports the following module(s):¶
<CODE BEGINS> file "ietf-te-device@2023-03-11.yang"
module ietf-te-device {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-te-device";
/* Replace with IANA when assigned */
prefix te-dev;
/* Import TE module */
import ietf-te {
prefix te;
reference
"RFCXXXX: A YANG Data Model for Traffic Engineering
Tunnels and Interfaces";
}
/* Import TE types */
import ietf-te-types {
prefix te-types;
reference
"RFC8776: Common YANG Data Types for Traffic Engineering.";
}
import ietf-interfaces {
prefix if;
reference
"RFC8343: A YANG Data Model for Interface Management";
}
import ietf-routing-types {
prefix rt-types;
reference
"RFC8294: Common YANG Data Types for the Routing Area";
}
organization
"IETF Traffic Engineering Architecture and Signaling (TEAS)
Working Group";
contact
"WG Web: <https://tools.ietf.org/wg/teas/>
WG List: <mailto:teas@ietf.org>
Editor: Tarek Saad
<mailto:tsaad.net@gmail.com>
Editor: Rakesh Gandhi
<mailto:rgandhi@cisco.com>
Editor: Vishnu Pavan Beeram
<mailto:vbeeram@juniper.net>
Editor: Himanshu Shah
<mailto:hshah@ciena.com>
Editor: Xufeng Liu
<mailto: xufeng.liu.ietf@gmail.com>
Editor: Igor Bryskin
<mailto:i_bryskin@yahoo.com>";
description
"This module defines a data model for TE device configurations,
state, and RPCs. The model fully conforms to the
Network Management Datastore Architecture (NMDA).
Copyright (c) 2023 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject to
the license terms contained in, the Revised BSD License set
forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX
(https://www.rfc-editor.org/info/rfcXXXX); see the RFC itself
for full legal notices.";
// RFC Ed.: replace XXXX with actual RFC number and remove this
// note.
// RFC Ed.: update the date below with the date of RFC publication
// and remove this note.
revision 2023-03-11 {
description
"Initial revision for the TE device YANG module.";
reference
"RFCXXXX: A YANG Data Model for Traffic Engineering Tunnels
and Interfaces";
}
grouping lsp-device-timers {
description
"Device TE LSP timers configs.";
leaf lsp-install-interval {
type uint32;
units "seconds";
description
"TE LSP installation delay time.";
}
leaf lsp-cleanup-interval {
type uint32;
units "seconds";
description
"TE LSP cleanup delay time.";
}
leaf lsp-invalidation-interval {
type uint32;
units "seconds";
description
"TE LSP path invalidation before taking action delay time.";
}
}
grouping te-igp-flooding-bandwidth-config {
description
"Configurable items for igp flooding bandwidth
threshold configuration.";
leaf threshold-type {
type enumeration {
enum delta {
description
"'delta' indicates that the local
system should flood IGP updates when a
change in reserved bandwidth >= the specified
delta occurs on the interface.";
}
enum threshold-crossed {
description
"THRESHOLD-CROSSED indicates that
the local system should trigger an update (and
hence flood) the reserved bandwidth when the
reserved bandwidth changes such that it crosses,
or becomes equal to one of the threshold values.";
}
}
description
"The type of threshold that should be used to specify the
values at which bandwidth is flooded. 'delta' indicates that
the local system should flood IGP updates when a change in
reserved bandwidth >= the specified delta occurs on the
interface. Where 'threshold-crossed' is specified, the local
system should trigger an update (and hence flood) the
reserved bandwidth when the reserved bandwidth changes such
that it crosses, or becomes equal to one of the threshold
values.";
}
leaf delta-percentage {
when "../threshold-type = 'delta'" {
description
"The percentage delta can only be specified when the
threshold type is specified to be a percentage delta of
the reserved bandwidth.";
}
type rt-types:percentage;
description
"The percentage of the maximum-reservable-bandwidth
considered as the delta that results in an IGP update
being flooded.";
}
leaf threshold-specification {
when "../threshold-type = 'threshold-crossed'" {
description
"The selection of whether mirrored or separate threshold
values are to be used requires user specified thresholds
to be set.";
}
type enumeration {
enum mirrored-up-down {
description
"mirrored-up-down indicates that a single set of
threshold values should be used for both increasing
and decreasing bandwidth when determining whether
to trigger updated bandwidth values to be flooded
in the IGP TE extensions.";
}
enum separate-up-down {
description
"separate-up-down indicates that a separate
threshold values should be used for the increasing
and decreasing bandwidth when determining whether
to trigger updated bandwidth values to be flooded
in the IGP TE extensions.";
}
}
description
"This value specifies whether a single set of threshold
values should be used for both increasing and decreasing
bandwidth when determining whether to trigger updated
bandwidth values to be flooded in the IGP TE extensions.
'mirrored-up-down' indicates that a single value (or set of
values) should be used for both increasing and decreasing
values, where 'separate-up-down' specifies that the
increasing and decreasing values will be separately
specified.";
}
leaf-list up-thresholds {
when "../threshold-type = 'threshold-crossed'"
+ "and ../threshold-specification = 'separate-up-down'" {
description
"A list of up-thresholds can only be specified when the
bandwidth update is triggered based on crossing a
threshold and separate up and down thresholds are
required.";
}
type rt-types:percentage;
description
"The thresholds (expressed as a percentage of the maximum
reservable bandwidth) at which bandwidth updates are to be
triggered when the bandwidth is increasing.";
}
leaf-list down-thresholds {
when "../threshold-type = 'threshold-crossed'"
+ "and ../threshold-specification = 'separate-up-down'" {
description
"A list of down-thresholds can only be specified when the
bandwidth update is triggered based on crossing a
threshold and separate up and down thresholds are
required.";
}
type rt-types:percentage;
description
"The thresholds (expressed as a percentage of the maximum
reservable bandwidth) at which bandwidth updates are to be
triggered when the bandwidth is decreasing.";
}
leaf-list up-down-thresholds {
when "../threshold-type = 'threshold-crossed'"
+ "and ../threshold-specification = 'mirrored-up-down'" {
description
"A list of thresholds corresponding to both increasing
and decreasing bandwidths can be specified only when an
update is triggered based on crossing a threshold, and
the same up and down thresholds are required.";
}
type rt-types:percentage;
description
"The thresholds (expressed as a percentage of the maximum
reservable bandwidth of the interface) at which bandwidth
updates are flooded - used both when the bandwidth is
increasing and decreasing.";
}
}
/**
* TE device augmentations
*/
augment "/te:te" {
description
"TE global container.";
/* TE Interface Configuration Data */
container interfaces {
description
"Configuration data model for TE interfaces.";
uses te-igp-flooding-bandwidth-config;
list interface {
key "interface";
description
"TE interfaces.";
leaf interface {
type if:interface-ref;
description
"TE interface name.";
}
/* TE interface parameters */
leaf te-metric {
type te-types:te-metric;
description
"TE interface metric.";
}
choice admin-group-type {
description
"TE interface administrative groups
representation type.";
case value-admin-groups {
choice value-admin-group-type {
description
"choice of admin-groups.";
case admin-groups {
description
"Administrative group/Resource
class/Color.";
leaf admin-group {
type te-types:admin-group;
description
"TE interface administrative group.";
}
}
case extended-admin-groups {
if-feature "te-types:extended-admin-groups";
description
"Extended administrative group/Resource
class/Color.";
leaf extended-admin-group {
type te-types:extended-admin-group;
description
"TE interface extended administrative group.";
}
}
}
}
case named-admin-groups {
list named-admin-groups {
if-feature "te-types:extended-admin-groups";
if-feature "te-types:named-extended-admin-groups";
key "named-admin-group";
description
"A list of named admin-group entries.";
leaf named-admin-group {
type leafref {
path "../../../../te:globals/"
+ "te:named-admin-groups/te:named-admin-group/"
+ "te:name";
}
description
"A named admin-group entry.";
}
}
}
}
choice srlg-type {
description
"Choice of SRLG configuration.";
case value-srlgs {
list values {
key "value";
description
"List of SRLG values that
this link is part of.";
leaf value {
type uint32 {
range "0..4294967295";
}
description
"Value of the SRLG";
}
}
}
case named-srlgs {
list named-srlgs {
if-feature "te-types:named-srlg-groups";
key "named-srlg";
description
"A list of named SRLG entries.";
leaf named-srlg {
type leafref {
path "../../../../te:globals/"
+ "te:named-srlgs/te:named-srlg/te:name";
}
description
"A named SRLG entry.";
}
}
}
}
uses te-igp-flooding-bandwidth-config;
list switching-capabilities {
key "switching-capability";
description
"List of interface capabilities for this interface.";
leaf switching-capability {
type identityref {
base te-types:switching-capabilities;
}
description
"Switching Capability for this interface.";
}
leaf encoding {
type identityref {
base te-types:lsp-encoding-types;
}
description
"Encoding supported by this interface.";
}
}
container te-advertisements-state {
config false;
description
"TE interface advertisements state container.";
leaf flood-interval {
type uint32;
description
"The periodic flooding interval.";
}
leaf last-flooded-time {
type uint32;
units "seconds";
description
"Time elapsed since last flooding in seconds.";
}
leaf next-flooded-time {
type uint32;
units "seconds";
description
"Time remained for next flooding in seconds.";
}
leaf last-flooded-trigger {
type enumeration {
enum link-up {
description
"Link-up flooding trigger.";
}
enum link-down {
description
"Link-down flooding trigger.";
}
enum threshold-up {
description
"Bandwidth reservation up threshold.";
}
enum threshold-down {
description
"Bandwidth reservation down threshold.";
}
enum bandwidth-change {
description
"Bandwidth capacity change.";
}
enum user-initiated {
description
"Initiated by user.";
}
enum srlg-change {
description
"SRLG property change.";
}
enum periodic-timer {
description
"Periodic timer expired.";
}
}
default "periodic-timer";
description
"Trigger for the last flood.";
}
list advertised-level-areas {
key "level-area";
description
"List of level-areas that the TE interface is
advertised in.";
leaf level-area {
type uint32;
description
"The IGP area or level where the TE interface link
state is advertised in.";
}
}
}
}
}
}
/* TE globals device augmentation */
augment "/te:te/te:globals" {
description
"Global TE device specific configuration parameters.";
uses lsp-device-timers;
}
/* TE tunnels device configuration augmentation */
augment "/te:te/te:tunnels/te:tunnel" {
description
"Tunnel device dependent augmentation.";
leaf path-invalidation-action {
type identityref {
base te-types:path-invalidation-action-type;
}
description
"Tunnel path invalidation action.";
}
uses lsp-device-timers;
}
/* TE LSPs device state augmentation */
augment "/te:te/te:lsps/te:lsp" {
description
"TE LSP device dependent augmentation.";
container lsp-timers {
when "../te:origin-type = 'ingress'" {
description
"Applicable to ingress LSPs only.";
}
description
"Ingress LSP timers.";
leaf uptime {
type uint32;
units "seconds";
description
"The LSP uptime.";
}
leaf time-to-install {
type uint32;
units "seconds";
description
"The time remaining for a new LSP to be instantiated
in forwarding to carry traffic.";
}
leaf time-to-destroy {
type uint32;
units "seconds";
description
"The time remaining for a existing LSP to be deleted
from forwarding.";
}
}
container downstream-info {
when "../te:origin-type != 'egress'" {
description
"Downstream information of the LSP.";
}
description
"downstream information.";
leaf nhop {
type te-types:te-tp-id;
description
"downstream next-hop address.";
}
leaf outgoing-interface {
type if:interface-ref;
description
"downstream interface.";
}
container neighbor {
uses te:te-generic-node-id;
description
"downstream neighbor address.";
}
leaf label {
type rt-types:generalized-label;
description
"downstream label.";
}
}
container upstream-info {
when "../te:origin-type != 'ingress'" {
description
"Upstream information of the LSP.";
}
description
"upstream information.";
leaf phop {
type te-types:te-tp-id;
description
"upstream next-hop or previous-hop address.";
}
container neighbor {
uses te:te-generic-node-id;
description
"upstream neighbor address.";
}
leaf label {
type rt-types:generalized-label;
description
"upstream label.";
}
}
}
/* TE interfaces RPCs/execution Data */
rpc link-state-update {
description
"Triggers a link state update for the specific interface.";
input {
choice filter-type {
mandatory true;
description
"Filter choice.";
case match-all {
leaf all {
type empty;
mandatory true;
description
"Match all TE interfaces.";
}
}
case match-one-interface {
leaf interface {
type if:interface-ref;
description
"Match a specific TE interface.";
}
}
}
}
}
}
<CODE ENDS>
Notifications are a key component of any topology data model.¶
[RFC8639] and [RFC8641] define a subscription mechanism and a push mechanism for YANG datastores. These mechanisms currently allow the user to:¶
This document registers the following URIs in the IETF XML registry [RFC3688]. Following the format in [RFC3688], the following registrations are requested to be made.¶
URI: urn:ietf:params:xml:ns:yang:ietf-te Registrant Contact: The IESG. XML: N/A, the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-te-device Registrant Contact: The IESG. XML: N/A, the requested URI is an XML namespace.¶
This document registers two YANG modules in the YANG Module Names registry [RFC6020].¶
Name: ietf-te Namespace: urn:ietf:params:xml:ns:yang:ietf-te Prefix: te Reference: RFCXXXX Name: ietf-te-device Namespace: urn:ietf:params:xml:ns:yang:ietf-te-device Prefix: te-device Reference: RFCXXXX¶
The YANG module specified in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].¶
The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.¶
There are a number of data nodes defined in this YANG module that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) to these data nodes without proper protection can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/vulnerability:¶
"/te/globals": This module specifies the global TE configurations on a device. Unauthorized access to this container could cause the device to ignore packets it should receive and process.¶
"/te/tunnels": This list specifies the configuration and state of TE Tunnels present on the device or controller. Unauthorized access to this list could cause the device to ignore packets it should receive and process. An attacker may also use state to derive information about the network topology, and subsequently orchestrate further attacks.¶
"/te/interfaces": This list specifies the configuration and state TE interfaces on a device. Unauthorized access to this list could cause the device to ignore packets it should receive and process.¶
Some of the readable data nodes in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control read access (e.g., via get, get-config, or notification) to these data nodes. These are the subtrees and data nodes and their sensitivity/vulnerability:¶
"/te/lsps": this list contains information state about established LSPs in the network. An attacker can use this information to derive information about the network topology, and subsequently orchestrate further attacks.¶
Some of the RPC operations in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control access to these operations. These are the operations and their sensitivity/vulnerability:¶
"/te/tunnels-actions": using this RPC, an attacker can modify existing paths that may be carrying live traffic, and hence result to interruption to services carried over the network.¶
"/te/tunnels-path-compute": using this RPC, an attacker can retrieve secured information about the network provider which can be used to orchestrate further attacks.¶
The security considerations spelled out in the YANG 1.1 specification [RFC7950] apply for this document as well.¶
The authors would like to thank the members of the multi-vendor YANG design team who are involved in the definition of this model.¶
The authors would like to thank Tom Petch and Adrian Farrel for reviewing and providing useful feedback about the document. The authors would also like to thank Loa Andersson, Lou Berger, Sergio Belotti, Italo Busi, Carlo Perocchio, Francesco Lazzeri, Aihua Guo, Dhruv Dhody, and Raqib Jones for providing feedback on this document.¶
Himanshu Shah Ciena Email: hshah@ciena.com Xia Chen Huawei Technologies Email: jescia.chenxia@huawei.com Bin Wen Comcast Email: Bin_Wen@cable.comcast.com¶
This section contains examples of use of the model with RESTCONF [RFC8040] and JSON encoding.¶
For the example we will use a 4 node MPLS network were RSVP-TE MPLS Tunnels can be setup. The loopbacks of each router are shown. The network in Figure 11 will be used in the examples described in the following sections.¶
192.0.2.1 192.0.2.2 192.0.2.4
+-------+ +-------+ +-------+
| | | | | |
| A +--------+ B +------+ D |
+---+---+ +-------+ +---+---+
| |
| +-------+ |
| | | |
+------------+ C +----------+
| |
+-------+
192.0.2.3
This example uses the TE Tunnel YANG data model defined in this document to create an RSVP-TE signaled Tunnel of packet LSP encoding type. First, the TE Tunnel is created with no specific restrictions or constraints (e.g., protection or restoration). The TE Tunnel ingresses on router A and egresses on router D.¶
In this case, the TE Tunnel is created without specifying additional information about the primary paths.¶
POST /restconf/data/ietf-te:te/tunnels HTTP/1.1
Host: example.com
Accept: application/yang-data+json
Content-Type: application/yang-data+json
{
"ietf-te:tunnel": [
{
"name": "Example_LSP_Tunnel_A_2",
"encoding": "te-types:lsp-encoding-packet",
"admin-state": "te-types:tunnel-state-up",
"source": "192.0.2.1",
"destination": "192.0.2.4",
"bidirectional": "false",
"signaling-type": "te-types:path-setup-rsvp"
}
]
}
¶
This example uses the YANG data model to create a 'named path constraint' that can be reference by TE Tunnels. The path constraint, in this case, limits the TE Tunnel hops for the computed path.¶
POST /restconf/data/ietf-te:te/globals/named-path-constraints
HTTP/1.1
Host: example.com
Accept: application/yang-data+json
Content-Type: application/yang-data+json
"ietf-te:named-path-constraint": {
"name": "max-hop-3",
"path-metric-bounds": {
"path-metric-bound": {
"metric-type": "te-types:path-metric-hop",
"upper-bound": "3"
}
}
}
}
¶
In this example, the previously created 'named path constraint' is applied to the TE Tunnel created in Section 12.1.¶
POST /restconf/data/ietf-te:te/tunnels HTTP/1.1
Host: example.com
Accept: application/yang-data+json
Content-Type: application/yang-data+json
{
"ietf-te:ietf-tunnel": [
{
"name": "Example_LSP_Tunnel_A_4_1",
"encoding": "te-types:lsp-encoding-packet",
"description": "Simple_LSP_with_named_path",
"admin-state": "te-types:tunnel-state-up",
"source": "192.0.2.1",
"destination": "192.0.2.4",
"signaling-type": "path-setup-rsvp",
"primary-paths": [
{
"primary-path": {
"name": "Simple_LSP_1",
"use-path-computation": "true",
"named-path-constraint": "max-hop-3"
}
}
]
}
]
}
¶
In this example, the a per tunnel path constraint is explicitly indicated under the TE Tunnel created in Section 12.1 to constrain the computed path for the tunnel.¶
POST /restconf/data/ietf-te:te/tunnels HTTP/1.1
Host: example.com
Accept: application/yang-data+json
Content-Type: application/yang-data+json
{
"ietf-te:tunnel": [
{
"name": "Example_LSP_Tunnel_A_4_2",
"encoding": "te-types:lsp-encoding-packet",
"admin-state": "te-types:tunnel-state-up",
"source": "192.0.2.1",
"destination": "192.0.2.4",
"signaling-type": "te-types:path-setup-rsvp",
"primary-paths": {
"primary-path": [
{
"name": "path1",
"path-metric-bounds": {
"path-metric-bound": [
{
"metric-type": "te-types:path-metric-hop",
"upper-bound": "3"
}
]
}
}
]
}
}
]
}
¶
In this example, the 'GET' query is sent to return the state stored about the tunnel.¶
GET /restconf/data/ietf-te:te/tunnels +
/tunnel="Example_LSP_Tunnel_A_4_1"
/p2p-primary-paths/ HTTP/1.1
Host: example.com
Accept: application/yang-data+json
¶
The request, with status code 200 would include, for example, the following json:¶
{
"ietf-te:primary-paths": {
"primary-path": [
{
"name": "path1",
"path-computation-method": "te-types:path-locally-computed",
"computed-paths-properties": {
"computed-path-properties": [
{
"k-index": "1",
"path-properties": {
"path-route-objects": {
"path-route-object": [
{
"index": "1",
"numbered-node-hop": {
"node-id": "192.0.2.2"
}
},
{
"index": "2",
"numbered-node-hop": {
"node-id": "192.0.2.4"
}
}
]
}
}
}
]
},
"lsps": {
"lsp": [
{
"tunnel-name": "Example_LSP_Tunnel_A_4_1",
"node": "192.0.2.1 ",
"lsp-id": "25356"
}
]
}
}
]
}
}
¶
+----------+ +----------+
+-|192.0.2.9 |---+ |192.0.2.10|
| +----------+ | +----------+
| | | |
+----------+ +----------+ +----------+ | |
|192.0.2.8 |----|192.0.2.3 |-----|192.0.2.4 |----+ |
+----------+ +----------+ +----------+ |
| | | |
+----------+ | | |
|192.0.2.1 |---------+ | +----------+
+----------+ +-----------|192.0.2.5 |
| | +----------+
| | +----------+ | |
| +--------------|192.0.2.2 |---------------------+ |
| +----------+ |
| | | |
+----------+ | | +----------+
|192.0.2.6 |----------------+ +-------------------|192.0.2.7 |
+----------+ +----------+
Below is the state retrieved for a TE tunnel from source 192.0.2.1 to 192.0.2.5 with primary, secondary, reverse, and secondary reverse paths as shown in Figure 12.¶
{
"ietf-te:te": {
"tunnels": {
"tunnel": [
{
"name": "example-1",
"description": "Example in slide 1",
"source": "192.0.2.1",
"destination": "192.0.2.5",
"bidirectional": false,
"primary-paths": {
"primary-path": [
{
"name": "primary-1 (fwd)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.2",
"hop-type": "loose"
}
}
]
},
"primary-reverse-path": {
"name": "primary-2 (rev)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.3",
"hop-type": "loose"
}
}
]
},
"candidate-secondary-reverse-paths": {
"candidate-secondary-reverse-path": [
"secondary-3 (rev)",
"secondary-4 (rev)",
"secondary-5 (rev)"
]
}
},
"candidate-secondary-paths": {
"candidate-secondary-path": [
"secondary-1 (fwd)",
"secondary-2 (fwd)"
]
}
}
]
},
"secondary-paths": {
"secondary-path": [
{
"name": "secondary-1 (fwd)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.1"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.2",
"hop-type": "loose"
}
}
]
}
},
{
"name": "secondary-2 (fwd)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.2"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.5",
"hop-type": "loose"
}
}
]
}
}
]
},
"secondary-reverse-paths": {
"secondary-reverse-path": [
{
"name": "secondary-3 (rev)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.5"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.4",
"hop-type": "loose"
}
}
]
}
},
{
"name": "secondary-4 (rev)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.4"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.3",
"hop-type": "loose"
}
}
]
}
},
{
"name": "secondary-5 (rev)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.3"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.1",
"hop-type":"loose"
}
}
]
}
}
]
}
},
{
"name": "example-3",
"description": "Example in slide 3",
"source": "192.0.2.1",
"destination": "192.0.2.5",
"bidirectional": true,
"primary-paths": {
"primary-path": [
{
"name": "primary-1 (bidir)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.2",
"hop-type": "loose"
}
}
]
},
"candidate-secondary-paths": {
"candidate-secondary-path": [
"secondary-1 (bidir)",
"secondary-2 (bidir)"
]
}
}
]
},
"secondary-paths": {
"secondary-path": [
{
"name": "secondary-1 (bidir)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.1"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.2",
"hop-type": "loose"
}
}
]
}
},
{
"name": "secondary-2 (bidir)",
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.2"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.5",
"hop-type": "loose"
}
}
]
}
}
]
}
},
{
"name": "example-4",
"description": "Example in slide 4",
"source": "192.0.2.1",
"destination": "192.0.2.5",
"bidirectional": false,
"primary-paths": {
"primary-path": [
{
"name": "primary-1 (fwd)",
"co-routed": [null],
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.2",
"hop-type": "loose"
}
}
]
},
"primary-reverse-path": {
"name": "primary-2 (rev)",
"candidate-secondary-reverse-paths": {
"candidate-secondary-reverse-path": [
"secondary-3 (rev)",
"secondary-4 (rev)"
]
}
},
"candidate-secondary-paths": {
"candidate-secondary-path": [
"secondary-1 (fwd)",
"secondary-2 (fwd)"
]
}
}
]
},
"secondary-paths": {
"secondary-path": [
{
"name": "secondary-1 (fwd)",
"co-routed": [null],
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.1"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.2",
"hop-type": "loose"
}
}
]
}
},
{
"name": "secondary-2 (fwd)",
"co-routed": [null],
"explicit-route-objects-always": {
"route-object-include-exclude": [
{
"index": 1,
"numbered-node-hop": {
"node-id": "192.0.2.2"
}
},
{
"index": 2,
"numbered-node-hop": {
"node-id": "192.0.2.5",
"hop-type": "loose"
}
}
]
}
}
]
},
"secondary-reverse-paths": {
"secondary-reverse-path": [
{
"name": "secondary-3 (rev)"
},
{
"name": "secondary-4 (rev)"
}
]
}
}
]
}
}
}
¶
Figure 13 shows the full tree diagram of the TE YANG model defined in module 'ietf-te.yang'.¶
module: ietf-te
+--rw te
+--rw enable? boolean
+--rw globals
| +--rw named-admin-groups
| | +--rw named-admin-group* [name]
| | {te-types:extended-admin-groups,
| | te-types:named-extended-admin-groups}?
| | +--rw name string
| | +--rw bit-position? uint32
| +--rw named-srlgs
| | +--rw named-srlg* [name] {te-types:named-srlg-groups}?
| | +--rw name string
| | +--rw value? te-types:srlg
| | +--rw cost? uint32
| +--rw named-path-constraints
| +--rw named-path-constraint* [name]
| {te-types:named-path-constraints}?
| +--rw name string
| +---u path-constraints-common
+--rw tunnels
| +--rw tunnel* [name]
| +--rw name string
| +--rw alias? string
| +--rw identifier? uint32
| +--rw color? uint32
| +--rw description? string
| +--rw admin-state? identityref
| +--ro operational-state? identityref
| +---u te-types:encoding-and-switching-type
| +---u tunnel-common-attributes
| +--rw controller
| | +--rw protocol-origin? identityref
| | +--rw controller-entity-id? string
| +--rw reoptimize-timer? uint16
| +---u tunnel-associations-properties
| +---u protection-restoration-properties
| +---u te-types:tunnel-constraints
| +---u tunnel-hierarchy-properties
| +--rw primary-paths
| | +--rw primary-path* [name]
| | +---u path-common-properties
| | +---u path-forward-properties
| | +---u k-requested-paths
| | +---u path-compute-info
| | +---u path-state
| | +--rw primary-reverse-path
| | | +---u path-common-properties
| | | +---u path-compute-info
| | | +---u path-state
| | | +--rw candidate-secondary-reverse-paths
| | | +--rw candidate-secondary-reverse-path*
| | | [secondary-path]
| | | +--rw secondary-path leafref
| | +--rw candidate-secondary-paths
| | +--rw candidate-secondary-path* [secondary-path]
| | +--rw secondary-path leafref
| | +--ro active? boolean
| +--rw secondary-paths
| | +--rw secondary-path* [name]
| | +---u path-common-properties
| | +--rw preference? uint8
| | +---u path-compute-info
| | +---u protection-restoration-properties
| | +---u path-state
| +--rw secondary-reverse-paths
| | +--rw secondary-reverse-path* [name]
| | +---u path-common-properties
| | +--rw preference? uint8
| | +---u path-compute-info
| | +---u protection-restoration-properties
| | +---u path-state
| +---x tunnel-action
| | +---w input
| | | +---w action-type? identityref
| | +--ro output
| | +--ro action-result? identityref
| +---x protection-external-commands
| +---w input
| +---w protection-external-command? identityref
| +---w protection-group-ingress-node? boolean
| +---w protection-group-egress-node? boolean
| +---w path-name? string
| +---w path-type?
| | te-types:path-type
| +---w traffic-type? enumeration
| +---w extra-traffic-tunnel-ref? tunnel-ref
+--ro lsps
+--ro lsp* [tunnel-name lsp-id node]
+--ro tunnel-name string
+--ro lsp-id uint16
+--ro node
| te-types:te-node-id
+--ro source?
| te-types:te-node-id
+--ro destination?
| te-types:te-node-id
+--ro tunnel-id? uint16
+--ro extended-tunnel-id? yang:dotted-quad
+--ro operational-state? identityref
+--ro signaling-type? identityref
+--ro origin-type? enumeration
+--ro lsp-resource-status? enumeration
+--ro lockout-of-normal? boolean
+--ro freeze? boolean
+--ro lsp-protection-role? enumeration
+--ro lsp-protection-state? identityref
+--ro protection-group-ingress-node-id?
| te-types:te-node-id
+--ro protection-group-egress-node-id?
| te-types:te-node-id
+--ro lsp-actual-route-information
+--ro lsp-actual-route-information* [index]
+---u te-types:record-route-state
rpcs:
+---x tunnels-path-compute
| +---w input
| | +---w path-compute-info
| +--ro output
| +--ro path-compute-result
+---x tunnels-actions
+---w input
| +---w tunnel-info
| | +---w (filter-type)
| | +--:(all-tunnels)
| | | +---w all empty
| | +--:(one-tunnel)
| | +---w tunnel? tunnel-ref
| +---w action-info
| +---w action? identityref
| +---w disruptive? empty
+--ro output
+--ro action-result? identityref
grouping te-generic-node-id:
+-- id? te-gen-node-id
+-- type? enumeration
grouping path-common-properties:
+-- name? string
+-- path-computation-method? identityref
+-- path-computation-server
| +---u te-generic-node-id
+-- compute-only? empty
+-- use-path-computation? boolean
+-- lockdown? empty
+--ro path-scope? identityref
grouping path-compute-info:
+---u tunnel-associations-properties
+---u te-types:generic-path-optimization
+-- named-path-constraint? leafref
| {te-types:named-path-constraints}?
+---u path-constraints-common
grouping path-forward-properties:
+-- preference? uint8
+-- co-routed? boolean
grouping k-requested-paths:
+-- k-requested-paths? uint8
grouping path-state:
+---u path-computation-response
+--ro lsp-provisioning-error-infos
| +--ro lsp-provisioning-error-info* []
| +--ro error-reason? identityref
| +--ro error-description? string
| +--ro error-timestamp? yang:date-and-time
| +--ro error-node-id? te-types:te-node-id
| +--ro error-link-id? te-types:te-tp-id
| +--ro lsp-id? uint16
+--ro lsps
+--ro lsp* [node lsp-id]
+--ro tunnel-name? -> /te/lsps/lsp/tunnel-name
+--ro node? leafref
+--ro lsp-id? leafref
grouping path-computation-response:
+--ro computed-paths-properties
| +--ro computed-path-properties* [k-index]
| +--ro k-index? uint8
| +---u te-types:generic-path-properties
+--ro computed-path-error-infos
+--ro computed-path-error-info* []
+--ro error-description? string
+--ro error-timestamp? yang:date-and-time
+--ro error-reason? identityref
grouping protection-restoration-properties:
+-- protection
| +-- protection-type? identityref
| +-- protection-reversion-disable? boolean
| +-- hold-off-time? uint32
| +-- wait-to-revert? uint16
| +-- aps-signal-id? uint8
+-- restoration
+-- restoration-type? identityref
+-- restoration-scheme? identityref
+-- restoration-reversion-disable? boolean
+-- hold-off-time? uint32
+-- wait-to-restore? uint16
+-- wait-to-revert? uint16
grouping tunnel-associations-properties:
+-- association-objects
+-- association-object* [association-key]
| +-- association-key? string
| +-- type? identityref
| +-- id? uint16
| +-- source
| +---u te-generic-node-id
+-- association-object-extended* [association-key]
+-- association-key? string
+-- type? identityref
+-- id? uint16
+-- source
| +---u te-generic-node-id
+-- global-source? uint32
+-- extended-id? yang:hex-string
grouping tunnel-common-attributes:
+-- source? te-types:te-node-id
+-- destination? te-types:te-node-id
+-- src-tunnel-tp-id? binary
+-- dst-tunnel-tp-id? binary
+-- bidirectional? boolean
grouping tunnel-hierarchy-properties:
+-- hierarchy
+-- dependency-tunnels
| +-- dependency-tunnel* [name]
| +-- name?
| | -> /te/tunnels/tunnel/name
| +---u te-types:encoding-and-switching-type
+-- hierarchical-link
+-- enable? boolean
+-- local-te-node-id? te-types:te-node-id
+-- local-te-link-tp-id? te-types:te-tp-id
+-- remote-te-node-id? te-types:te-node-id
+---u te-types:te-topology-identifier
grouping path-constraints-common:
+---u te-types:common-path-constraints-attributes
+---u te-types:generic-path-disjointness
+---u te-types:path-constraints-route-objects
+-- path-in-segment!
| +---u te-types:label-set-info
+-- path-out-segment!
+---u te-types:label-set-info