| Internet-Draft | TAPS Interface | December 2023 |
| Trammell, et al. | Expires 16 June 2024 | [Page] |
This document describes an abstract application programming interface, API, to the transport layer that enables the selection of transport protocols and network paths dynamically at runtime. This API enables faster deployment of new protocols and protocol features without requiring changes to the applications. The specified API follows the Transport Services architecture by providing asynchronous, atomic transmission of messages. It is intended to replace the BSD sockets API as the common interface to the transport layer, in an environment where endpoints could select from multiple network paths and potential transport protocols.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 16 June 2024.¶
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
This document specifies an abstract application programming interface (API) that describes the interface component of the high-level Transport Services architecture defined in [I-D.ietf-taps-arch]. A Transport Services system supports asynchronous, atomic transmission of messages over transport protocols and network paths dynamically selected at runtime, in environments where an endpoint selects from multiple network paths and potential transport protocols.¶
Applications that adopt this API will benefit from a wide set of transport features that can evolve over time. This protocol-independent API ensures that the system providing the API can optimize its behavior based on the application requirements and network conditions, without requiring changes to the applications. This flexibility enables faster deployment of new features and protocols, and can support applications by offering racing and fallback mechanisms, which otherwise need to be separately implemented in each application. Transport Services Implementations are free to take any desired form as long as the API specification in this document is honored; a nonprescriptive guide to implementing a Transport Services system is available [I-D.ietf-taps-impl].¶
The Transport Services system derives specific path and protocol selection properties and supported transport features from the analysis provided in [RFC8095], [RFC8923], and [RFC8922]. The Transport Services API enables an implementation to dynamically choose a transport protocol rather than statically binding applications to a protocol at compile time. The Transport Services API also provides applications with a way to override transport selection and instantiate a specific stack, e.g., to support servers wishing to listen to a specific protocol. However, forcing a choice to use a specific transport stack is discouraged for general use, because it can reduce portability.¶
The Transport Services API is described in terms of¶
Objects with which an application can interact;¶
Actions the application can perform on these objects;¶
Events, which an object can send to an application to be processed asynchronously; and¶
Parameters associated with these actions and events.¶
The following notations, which can be combined, are used in this document:¶
An action that creates an object:¶
Object := Action()
¶
An action that creates an array of objects:¶
[]Object := Action()
¶
An action that is performed on an object:¶
Object.Action()
¶
An object sends an event:¶
Object -> Event<>
¶
An action takes a set of Parameters; an event contains a set of Parameters. action and event parameters whose names are suffixed with a question mark are optional.¶
Action(param0, param1?, ...)
Event<param0, param1?, ...>
¶
Objects that are passed as parameters to actions use call-by-value behavior. Actions associated with no object are actions on the API; they are equivalent to actions on a per-application global context.¶
Events are sent to the application or application-supplied code (e.g. framers, see Section 9.1.2) for processing; the details of event interfaces are platform- and implementation-specific, and can be implemented using other forms of asynchronous processing, as idiomatic for the implementing platform.¶
We also make use of the following basic types:¶
Boolean: Instances take the value true or false.¶
Integer: Instances take integer values.¶
Numeric: Instances take real number values.¶
String: Instances are represented in UTF-8.¶
Enumeration: A family of types in which each instance takes one of a fixed, predefined set of values specific to a given enumerated type.¶
Tuple: An ordered grouping of multiple value types, represented as a
comma-separated list in parentheses, e.g., (Enumeration, Preference).
Instances take a sequence of values each valid for the corresponding value
type.¶
Array: Denoted []Type, an instance takes a value for each of zero or more
elements in a sequence of the given Type. An array can be of fixed or
variable length.¶
Set: An unordered grouping of one or more different values of the same type.¶
For guidance on how these abstract concepts can be implemented in languages in accordance with language-specific design patterns and platform features, see Appendix A.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
The design of the API specified in this document is based on a set of principles, themselves an elaboration on the architectural design principles defined in [I-D.ietf-taps-arch]. The API defined in this document provides:¶
A Transport Services system that can offer a variety of transport protocols, independent of the Protocol Stacks that will be used at runtime. To the degree possible, all common features of these protocol stacks are made available to the application in a transport-independent way. This enables applications written to a single API to make use of transport protocols in terms of the features they provide.¶
A unified API to datagram and stream-oriented transports, allowing use of a common API for Connection establishment and closing.¶
Message-orientation, as opposed to stream-orientation, using application-assisted framing and deframing where the underlying transport does not provide these.¶
Asynchronous Connection establishment, transmission, and reception. This allows concurrent operations during establishment and event-driven application interactions with the transport layer.¶
Selection between alternate network paths, using additional information about the networks over which a Connection can operate (e.g. Provisioning Domain (PvD) information [RFC7556]) where available.¶
Explicit support for transport-specific features to be applied, when that particular transport is part of a chosen Protocol Stack.¶
Explicit support for security properties as first-order transport features.¶
Explicit support for configuration of cryptographic identities and transport security parameters persistent across multiple Connections.¶
Explicit support for multistreaming and multipath transport protocols, and the grouping of related Connections into Connection Groups through "cloning" of Connections (see Section 7.4). This function allows applications to take full advantage of new transport protocols supporting these features.¶
An application primarily interacts with this API through two objects: Preconnections and Connections. A Preconnection object (Section 6) represents a set of properties and constraints on the selection and configuration of paths and protocols to establish a Connection with an Endpoint. A Connection object represents an instance of a transport Protocol Stack on which data can be sent to and/or received from a Remote Endpoint (i.e., a logical connection that, depending on the kind of transport, can be bi-directional or unidirectional, and that can use a stream protocol or a datagram protocol). Connections are presented consistently to the application, irrespective of whether the underlying transport is connection-less or connection-oriented. Connections can be created from Preconnections in three ways:¶
by initiating the Preconnection (i.e., creating a Connection from the Preconnection, actively opening, as in a client; see Initiate() in Section 7.1),¶
by listening on the Preconnection (i.e., creating a Listener based on the Preconnection, passively opening, as in a server; see Listen() in Section 7.2),¶
or by a rendezvous for the Preconnection (i.e., peer to peer establishment; see Rendezvous() in Section 7.3).¶
Once a Connection is established, data can be sent and received on it in the form of Messages. The API supports the preservation of message boundaries both via explicit Protocol Stack support, and via application support through a Message Framer that finds message boundaries in a stream. Messages are received asynchronously through event handlers registered by the application. Errors and other notifications also happen asynchronously on the Connection. It is not necessary for an application to handle all events; some events can have implementation-specific default handlers.¶
The application SHOULD NOT assume that ignoring events (e.g., errors) is always safe.¶
The following usage examples illustrate how an application might use the Transport Services API to:¶
Act as a server, by listening for incoming Connections, receiving requests, and sending responses, see Section 3.1.1.¶
Act as a client, by connecting to a Remote Endpoint using Initiate, sending
requests, and receiving responses, see Section 3.1.2.¶
Act as a peer, by connecting to a Remote Endpoint using Rendezvous while simultaneously waiting for incoming Connections, sending Messages, and receiving Messages, see Section 3.1.3.¶
The examples in this section presume that a transport protocol is available between the Local and Remote Endpoints that provides Reliable Data Transfer, Preservation of Data Ordering, and Preservation of Message Boundaries. In this case, the application can choose to receive only complete Messages.¶
If none of the available transport protocols provides Preservation of Message Boundaries, but there is a transport protocol that provides a reliable ordered byte-stream, an application could receive this byte-stream as partial Messages and transform it into application-layer Messages. Alternatively, an application might provide a Message Framer, which can transform a sequence of Messages into a byte-stream and vice versa (Section 9.1.2).¶
This is an example of how an application might listen for incoming Connections using the Transport Services API, receive a request, and send a response.¶
LocalSpecifier := NewLocalEndpoint()
LocalSpecifier.WithInterface("any")
LocalSpecifier.WithService("https")
TransportProperties := NewTransportProperties()
TransportProperties.Require(preserve-msg-boundaries)
// Reliable Data Transfer and Preserve Order are Required by default
SecurityParameters := NewSecurityParameters()
SecurityParameters.Set(identity, myIdentity)
SecurityParameters.Set(server-certificate, myCertificate)
// Specifying a Remote Endpoint is optional when using Listen
Preconnection := NewPreconnection(LocalSpecifier,
TransportProperties,
SecurityParameters)
Listener := Preconnection.Listen()
Listener -> ConnectionReceived<Connection>
// Only receive complete messages in a Conn.Received handler
Connection.Receive()
Connection -> Received<messageDataRequest, messageContext>
//---- Receive event handler begin ----
Connection.Send(messageDataResponse)
Connection.Close()
// Stop listening for incoming Connections
// (this example supports only one Connection)
Listener.Stop()
//---- Receive event handler end ----
¶
This is an example of how an application might open two Connections to a remote application using the Transport Services API, and send a request as well as receive a response on each of them. The code designated with comments as "Ready event handler" could, e.g., be implemented as a callback function, for example. This function would receive the Connection that it expects to operate on ("Connection" and "Connection2" in the example), handed over using the variable name "C".¶
RemoteSpecifier := NewRemoteEndpoint()
RemoteSpecifier.WithHostName("example.com")
RemoteSpecifier.WithService("https")
TransportProperties := NewTransportProperties()
TransportProperties.Require(preserve-msg-boundaries)
// Reliable Data Transfer and Preserve Order are Required by default
SecurityParameters := NewSecurityParameters()
TrustCallback := NewCallback({
// Verify identity of the Remote Endpoint, return the result
})
SecurityParameters.SetTrustVerificationCallback(TrustCallback)
// Specifying a Local Endpoint is optional when using Initiate
Preconnection := NewPreconnection(RemoteSpecifier,
TransportProperties,
SecurityParameters)
Connection := Preconnection.Initiate()
Connection2 := Connection.Clone()
Connection -> Ready<>
Connection2 -> Ready<>
//---- Ready event handler for any Connection C begin ----
C.Send(messageDataRequest)
// Only receive complete messages
C.Receive()
//---- Ready event handler for any Connection C end ----
Connection -> Received<messageDataResponse, messageContext>
Connection2 -> Received<messageDataResponse, messageContext>
// Close the Connection in a Receive event handler
Connection.Close()
Connection2.Close()
¶
A Preconnection serves as a template for creating a Connection via initiating, listening, or via rendezvous. Once a Connection has been created, changes made to the Preconnection that was used to create it do not affect this Connection. Preconnections are reusable after being used to create a Connection, whether this Connection was closed or not. Hence, in the above example, it would be correct for the client to initiate a third Connection to the example.com server by continuing as follows:¶
//.. carry out adjustments to the Preconnection, if desired Connection3 := Preconnection.Initiate()¶
This is an example of how an application might establish a Connection with a
peer using Rendezvous, send a Message, and receive a Message.¶
// Configure local candidates: a port on the Local Endpoint
// and via a STUN server
HostCandidate := NewLocalEndpoint()
HostCandidate.WithPort(9876)
StunCandidate := NewLocalEndpoint()
StunCandidate.WithStunServer(address, port, credentials)
LocalCandidates = [HostCandidate, StunCandidate]
TransportProperties := // ...Configure transport properties
SecurityParameters := // ...Configure security properties
Preconnection := NewPreconnection(LocalCandidates,
[], // No remote candidates yet
TransportProperties,
SecurityParameters)
// Resolve the LocalCandidates. The Preconnection.Resolve()
// call resolves both local and remote candidates but, since
// the remote candidates have not yet been specified, the
// ResolvedRemote list returned will be empty and is not
// used.
ResolvedLocal, ResolvedRemote = Preconnection.Resolve()
// Application-specific code goes here to send the ResolvedLocal
// list to peer via some out-of-band signalling channel (e.g.,
// in a SIP message)
...
// Application-specific code goes here to receive RemoteCandidates
// (type []RemoteEndpoint, a list of RemoteEndpoint objects) from
// the peer via the signalling channel
...
// Add remote candidates and initiate the rendezvous:
Preconnection.AddRemote(RemoteCandidates)
Preconnection.Rendezvous()
Preconnection -> RendezvousDone<Connection>
//---- RendezvousDone event handler begin ----
Connection.Send(messageDataRequest)
Connection.Receive()
//---- RendezvousDone event handler end ----
Connection -> Received<messageDataResponse, messageContext>
// If new Remote Endpoint candidates are received from the
// peer over the signalling channel, for example if using
// Trickle ICE, then add them to the Connection:
Connection.AddRemote(NewRemoteCandidates)
// On a PathChange<> event, resolve the Local Endpoint Identifiers to
// see if a new Local Endpoint has become available and, if
// so, send to the peer as a new candidate and add to the
// Connection:
Connection -> PathChange<>
//---- PathChange event handler begin ----
ResolvedLocal, ResolvedRemote = Preconnection.Resolve()
if ResolvedLocal has changed:
// Application-specific code goes here to send the
// ResolvedLocal list to peer via signalling channel
...
// Add the new Local Endpoints to the Connection:
Connection.AddLocal(ResolvedLocal)
//---- PathChange event handler end ----
// Close the Connection in a Receive event handler
Connection.Close()
¶
Each application using the Transport Services API declares its preferences for how the Transport Services system is to operate. This is done by using Transport Properties, as defined in [I-D.ietf-taps-arch], at each stage of the lifetime of a Connection.¶
Transport Properties are divided into Selection, Connection, and Message Properties.¶
Selection Properties (see Section 6.2) can only be set
during pre-establishment. They are only used to specify which paths and
Protocol Stacks can be used and are preferred by the application.
Calling Initiate on a Preconnection creates an outbound Connection,
and the Selection Properties remain readable from the
Connection, but become immutable. Selection Properties
can be set on Preconnections, and the effect of Selection Properties
can be queried on Connections and Messages.¶
Connection Properties (see Section 8.1) are used to inform decisions made during establishment and to fine-tune the established Connection. They can be set during pre-establishment, and can be changed later. Connection Properties can be set on Connections and Preconnections; when set on Preconnections, they act as an initial default for the resulting Connections.¶
Message Properties (see Section 9.1.3) control the behavior of the selected protocol stack(s) when sending Messages. Message Properties can be set on Messages, Connections, and Preconnections; when set on the latter two, they act as an initial default for the Messages sent over those Connections.¶
Note that configuring Connection Properties and Message Properties on Preconnections is preferred over setting them later. Early specification of Connection Properties allows their use as additional input to the selection process. Protocol-specific Properties, which enable configuration of specialized features of a specific protocol (see Section 3.2 of [I-D.ietf-taps-arch]) are not used as an input to the selection process, but only support configuration if the respective protocol has been selected.¶
Transport Properties are referred to by property names, represented as case-insensitive strings. These names serve two purposes:¶
Allowing different components of a Transport Services Implementation to pass Transport Properties, e.g., between a language frontend and a policy manager, or as a representation of properties retrieved from a file or other storage.¶
Making the code of different Transport Services Implementations look similar. While individual programming languages might preclude strict adherence to the aforementioned naming convention (for instance, by prohibiting the use of hyphens in symbols), users interacting with multiple implementations will still benefit from the consistency resulting from the use of visually similar symbols.¶
Transport Property Names are hierarchically organized in the form [<Namespace>.]<PropertyName>.¶
The optional Namespace component and its trailing character . MUST be omitted for well-known,
generic properties, i.e., for properties that are not specific to a protocol.¶
Protocol-specific Properties MUST use the protocol acronym as the Namespace (e.g., a
Connection that uses TCP could support a TCP-specific Transport Property, such as the TCP user timeout
value, in a Protocol-specific Property called tcp.userTimeoutValue (see Section 8.2)).¶
Vendor or implementation specific properties MUST be placed in a Namespace starting with the underscore _ character
and SHOULD use a string identifying the vendor or implementation.¶
For IETF protocols, the name of a Protocol-specific Property MUST be specified in an IETF document published in the RFC Series after IETF review. An IETF protocol Namespace does not start with an underscore character.¶
Namespaces for each of the keywords provided in the IANA protocol numbers registry (see https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml) are reserved for Protocol-specific Properties and MUST NOT be used for vendor or implementation-specific properties. Terms listed as keywords as in the protocol numbers registry SHOULD be avoided as any part of a vendor- or implementation-specific property name.¶
Though Transport Property Names are case-insensitive, it is recommended to use camelCase to improve readability. Implementations may transpose Transport Property Names into snake_case or PascalCase to blend into the language environment.¶
Each Transport Property has one of the basic types described in Section 1.1.¶
Most Selection Properties (see Section 6.2) are of the Enumeration type, and use the Preference Enumeration, which takes one of five possible values (Prohibit, Avoid, No Preference, Prefer, or Require) denoting the level of preference for a given property during protocol selection.¶
This document defines a language- and platform-independent API of a Transport Services system. Given the wide variety of languages and language conventions used to write applications that use the transport layer to connect to other applications over the Internet, this independence makes this API necessarily abstract.¶
There is no interoperability benefit in tightly defining how the API is presented to application programmers across diverse platforms. However, maintaining the "shape" of the abstract API across different platforms reduces the effort for programmers who learn to use the Transport Services API to then apply their knowledge to another platform. That said, implementations have significant freedom in presenting this API to programmers, balancing the conventions of the protocol with the shape of the API. We make the following recommendations:¶
Actions, events, and errors in implementations of the Transport Services API SHOULD use the names given for them in the document, subject to capitalization, punctuation, and other typographic conventions in the language of the implementation, unless the implementation itself uses different names for substantially equivalent objects for networking by convention.¶
Transport Services systems SHOULD implement each Selection Property,
Connection Property, and Message Context Property specified in this document.
These features SHOULD be implemented even when in a specific implementation it
will always result in no operation, e.g. there is no action when the API
specifies a Property that is not available in a transport protocol implemented
on a specific platform. For example, if TCP is the only underlying transport protocol,
the Message Property msgOrdered can be implemented (trivially, as a no-op) as
disabling the requirement for ordering will not have any effect on delivery order
for Connections over TCP. Similarly, the msgLifetime Message Property can be
implemented but ignored, as the description of this Property states that "it is not
guaranteed that a Message will not be sent when its Lifetime has expired".¶
Implementations can use other representations for Transport Property Names, e.g., by providing constants, but should provide a straight-forward mapping between their representation and the property names specified here.¶
The pre-establishment phase allows applications to specify properties for the Connections that they are about to make, or to query the API about potential Connections they could make.¶
A Preconnection object represents a potential Connection. It is a passive object (a data structure) that merely maintains the state that describes the properties of a Connection that might exist in the future. This state comprises Local Endpoint and Remote Endpoint objects that denote the endpoints of the potential Connection (see Section 6.1), the Selection Properties (see Section 6.2), any preconfigured Connection Properties (Section 8.1), and the security parameters (see Section 6.3):¶
Preconnection := NewPreconnection([]LocalEndpoint,
[]RemoteEndpoint,
TransportProperties,
SecurityParameters)
¶
At least one Local Endpoint MUST be specified if the Preconnection is used to Listen
for incoming Connections, but the list of Local Endpoints MAY be empty if
the Preconnection is used to Initiate
connections. If no Local Endpoint is specified, the Transport Services system will
assign an ephemeral local port to the Connection on the appropriate interface(s).
At least one Remote Endpoint MUST be specified if the Preconnection is used
to Initiate Connections, but the list of Remote Endpoints MAY be empty if
the Preconnection is used to Listen for incoming Connections.
At least one Local Endpoint and one Remote Endpoint MUST be specified if a
peer-to-peer Rendezvous is to occur based on the Preconnection.¶
If more than one Local Endpoint is specified on a Preconnection, then the application
is indicating that all of the Local Endpoints are eligible to be used for Connections. For
example, their Endpoint Identifiers might correspond to different interfaces on a multi-homed
host, or their Endpoint Identifiers might correspond to local interfaces and a STUN server that
can be resolved to a server reflexive address for a Preconnection used to
make a peer-to-peer Rendezvous.¶
If more than one Remote Endpoint is specified on the Preconnection, the application is indicating that it expects all of the Remote Endpoints to offer an equivalent service, and that the Transport Services system can choose any of them for a Connection. For example, a Remote Endpoint might represent various network interfaces of a host, or a server reflexive address that can be used to reach a host, or a set of hosts that provide equivalent local balanced service.¶
In most cases, it is expected that a single Remote Endpoint will be
specified by name, and a later call to Initiate on the Preconnection
(see Section 7.1) will internally resolve that name to a list of concrete
Endpoint Identifers. Specifying multiple Remote Endpoints on a Preconnection allows
applications to override this for more detailed control.¶
If Message Framers are used (see Section 9.1.2), they MUST be added to the Preconnection during pre-establishment.¶
The Transport Services API uses the Local Endpoint and Remote Endpoint objects to refer to the endpoints of a Connection. Endpoints can be created as either remote or local:¶
RemoteSpecifier := NewRemoteEndpoint() LocalSpecifier := NewLocalEndpoint()¶
A single Endpoint object represents the identity of a network host. That endpoint can be more or less specific depending on which Endpoint Identifiers are set. For example, an Endpoint that only specifies a hostname can, in fact, finally correspond to several different IP addresses on different hosts.¶
An Endpoint object can be configured with the following identifiers:¶
HostName (string):¶
RemoteSpecifier.WithHostName("example.com")
¶
Port (a 16-bit unsigned Integer):¶
RemoteSpecifier.WithPort(443)¶
Service (an identifier string that maps to a port; either a service name associated with a port number, from https://www.iana.org/assignments/service-names-port-numbers/service-names-port-numbers.xhtml, or a DNS SRV service name to be resolved):¶
RemoteSpecifier.WithService("https")
¶
IP address (IPv4 or IPv6 address):¶
RemoteSpecifier.WithIPAddress(192.0.2.21)¶
RemoteSpecifier.WithIPAddress(2001:db8:4920:e29d:a420:7461:7073:a)¶
Interface name (string), e.g., to qualify link-local addresses (see Section 6.1.2 for details):¶
LocalSpecifier.WithInterface("en0")
¶
The Resolve action on a Preconnection can be used to obtain a list of
available local interfaces.¶
Note that an IPv6 address specified with a scope zone ID (e.g. fe80::2001:db8%en0)
is equivalent to WithIPAddress with an unscoped address and WithInterface together.¶
Applications creating Endpoint objects using WithHostName SHOULD provide fully-qualified
domain names (FQDNs). Not providing an FQDN will result in the Transport Services Implementation
needing to resolve using DNS search domains, which might lead to inconsistent or unpredictable
behavior.¶
The design of the API MUST NOT permit an Endpoint object to be configured with multiple Endpoint Identifiers of the same type. For example, an Endpoint object cannot specify two IP addresses. Two separate IP addresses are represented as two Endpoint objects. If a Preconnection specifies a Remote Endpoint with a specific IP address set, it will only establish Connections to that IP address. If, on the other hand, a Remote Endpoint specifies a hostname but no addresses, the Transport Services Implementation can perform name resolution and attempt using any address derived from the original hostname of the Remote Endpoint. Note that multiple Remote Endpoints can be added to a Preconnection, as discussed in Section 7.5.¶
The Transport Services system resolves names internally, when the Initiate,
Listen, or Rendezvous method is called to establish a Connection. Privacy
considerations for the timing of this resolution are given in Section 13.¶
The Resolve action on a Preconnection can be used by the application to force
early binding when required, for example with some Network Address Translator
(NAT) traversal protocols (see Section 7.3).¶
To use multicast, a Preconnection is first created with the Local/Remote Endpoint Identifer
specifying the any-source multicast (ASM) or source-specific multicast (SSM) multicast group and destination port number.
This is then followed by a call to either Initiate, Listen, or
Rendezvous depending on whether the resulting Connection is to be
used to send messages to the multicast group, receive messages from
the group, or, for an any-source multicast group, to both send and
receive messages.¶
Note that the Transport Services API has separate specifier calls for multicast groups to avoid introducing filter properties for single-source multicast and seeks to avoid confusion that can be caused by overloading the unicast specifiers.¶
Calling Initiate on that Preconnection creates a Connection that can be
used to send Messages to the multicast group. The Connection object that is
created will support Send but not Receive. Any Connections created this
way are send-only, and do not join the multicast group. The resulting
Connection will have a Local Endpoint identifying the local interface to
which the Connection is bound and a Remote Endpoint identifying the
multicast group.¶
The following API calls can be used to configure a Preconnection before calling Initiate:¶
RemoteSpecifier.WithMulticastGroupIP(GroupAddress) RemoteSpecifier.WithPort(PortNumber) RemoteSpecifier.WithHopLimit(HopLimit)¶
Calling Listen on a Preconnection with a multicast group specified on the Remote
Endpoint will join the multicast group to receive Messages. This Listener
will create one Connection for each Remote Endpoint sending to the group,
with the Local Endpoint Identifer specified as a group address. The set of Connection
objects created forms a Connection Group.
The receiving interface can be restricted by passing it as part of the LocalSpecifier or queried through the Message Context on the Messages received (see Section 9.1.1 for further details).¶
Specifying WithHopLimit sets the Time To Live (TTL) field in the header of IPv4 packets or the Hop Count field in the header of IPv6 packets.¶
The following API calls can be used to configure a Preconnection before calling Listen:¶
LocalSpecifier.WithSingleSourceMulticastGroupIP(GroupAddress,
SourceAddress)
LocalSpecifier.WithAnySourceMulticastGroupIP(GroupAddress)
LocalSpecifier.WithPort(PortNumber)
¶
Calling Rendezvous on a Preconnection with an any-source multicast group
address as the Remote Endpoint Identifer will join the multicast group, and also
indicates that the resulting Connection can be used to send Messages to the
multicast group. The Rendezvous call will return both a Connection that
can be used to send to the group, that acts the same as a Connection
returned by calling Initiate with a multicast Remote Endpoint, and a
Listener that acts as if Listen had been called with a multicast Remote
Endpoint.
Calling Rendezvous on a Preconnection with a source-specific multicast
group address as the Local Endpoint Identifer results in an EstablishmentError.¶
The following API calls can be used to configure a Preconnection before calling Rendezvous:¶
RemoteSpecifier.WithMulticastGroupIP(GroupAddress) RemoteSpecifier.WithPort(PortNumber) RemoteSpecifier.WithHopLimit(HopLimit) LocalSpecifier.WithAnySourceMulticastGroupIP(GroupAddress) LocalSpecifier.WithPort(PortNumber) LocalSpecifier.WithHopLimit(HopLimit)¶
See Section 6.1.5 for more examples.¶
Note that this API has multiple ways to constrain and prioritize endpoint candidates based on the network interface:¶
Specifying an interface on a Remote Endpoint qualifies the scope zone of the Remote Endpoint, e.g., for link-local addresses.¶
Specifying an interface on a Local Endpoint explicitly binds all candidates derived from this Endpoint to use the specified interface.¶
Specifying an interface using the interface Selection Property (Section 6.2.11) or indirectly via the pvd Selection Property (Section 6.2.12) influences the selection among the available candidates.¶
While specifying an Interface on an Endpoint restricts the candidates available for Connection establishment in the Pre-Establishment Phase, the Selection Properties prioritize and constrain the Connection establishment.¶
An Endpoint can have an alternative definition when using different protocols. For example, a server that supports both TLS/TCP and QUIC could be accessible on two different port numbers depending on which protocol is used.¶
To scope an Endpoint to apply conditionally to a specific transport protocol (such as defining an alternate port to use when QUIC is selected, as opposed to TCP), an Endpoint can be associated with a protocol identifier. Protocol identifiers are objects or enumeration values provided by the Transport Services API, which will vary based on which protocols are implemented in a particular system.¶
AlternateRemoteSpecifier.WithProtocol(QUIC)¶
The following example shows a case where example.com has a server
running on port 443, with an alternate port of 8443 for QUIC. Both
endpoints can be passed when creating a Preconnection.¶
RemoteSpecifier := NewRemoteEndpoint()
RemoteSpecifier.WithHostName("example.com")
RemoteSpecifier.WithPort(443)
QUICRemoteSpecifier := NewRemoteEndpoint()
QUICRemoteSpecifier.WithHostName("example.com")
QUICRemoteSpecifier.WithPort(8443)
QUICRemoteSpecifier.WithProtocol(QUIC)
RemoteSpecifiers := [ RemoteSpecifier, QUICRemoteSpecifier ]
¶
The following examples of Endpoints show common usage patterns.¶
Specify a Remote Endpoint using a hostname "example.com" and a service name "https", which tells the system to use the default port for HTTPS (443):¶
RemoteSpecifier := NewRemoteEndpoint()
RemoteSpecifier.WithHostName("example.com")
RemoteSpecifier.WithService("https")
¶
Specify a Remote Endpoint using an IPv6 address and remote port:¶
RemoteSpecifier := NewRemoteEndpoint() RemoteSpecifier.WithIPAddress(2001:db8:4920:e29d:a420:7461:7073:a) RemoteSpecifier.WithPort(443)¶
Specify a Remote Endpoint using an IPv4 address and remote port:¶
RemoteSpecifier := NewRemoteEndpoint() RemoteSpecifier.WithIPAddress(192.0.2.21) RemoteSpecifier.WithPort(443)¶
Specify a Local Endpoint using a local interface name and no local port, to let the system assign an ephemeral local port:¶
LocalSpecifier := NewLocalEndpoint()
LocalSpecifier.WithInterface("en0")
¶
Specify a Local Endpoint using a local interface name and local port:¶
LocalSpecifier := NewLocalEndpoint()
LocalSpecifier.WithInterface("en0")
LocalSpecifier.WithPort(443)
¶
As an alternative to specifying an interface name for the Local Endpoint, an application
can express more fine-grained preferences using the Interface Instance or Type
Selection Property, see Section 6.2.11. However, if the application specifies Selection
Properties that are inconsistent with the Local Endpoint, this will result in an error once the
application attempts to open a Connection.¶
Specify a Local Endpoint using a STUN server:¶
LocalSpecifier := NewLocalEndpoint() LocalSpecifier.WithStunServer(address, port, credentials)¶
The following examples show how multicast groups can be used.¶
Join an Any-Source Multicast group in receive-only mode, bound to a known port on a named local interface:¶
RemoteSpecifier := NewRemoteEndpoint()
LocalSpecifier := NewLocalEndpoint()
LocalSpecifier.WithAnySourceMulticastGroupIP(233.252.0.0)
LocalSpecifier.WithPort(5353)
LocalSpecifier.WithInterface("en0")
TransportProperties := ...
SecurityParameters := ...
Preconnection := NewPreconnection(LocalSpecifier,
RemoteSpecifier,
TransportProperties,
SecurityProperties)
Listener := Preconnection.Listen()
¶
Join a Source-Specific Multicast group in receive-only mode, bound to a known port on a named local interface:¶
RemoteSpecifier := NewRemoteEndpoint()
LocalSpecifier := NewLocalEndpoint()
LocalSpecifier.WithSingleSourceMulticastGroupIP(233.252.0.0,
198.51.100.10)
LocalSpecifier.WithPort(5353)
LocalSpecifier.WithInterface("en0")
TransportProperties := ...
SecurityParameters := ...
Preconnection := NewPreconnection(LocalSpecifier,
RemoteSpecifier,
TransportProperties,
SecurityProperties)
Listener := Preconnection.Listen()
¶
Create a Source-Specific Multicast group as a sender:¶
RemoteSpecifier := NewRemoteEndpoint()
RemoteSpecifier.WithMulticastGroupIP(233.251.240.1)
RemoteSpecifier.WithPort(5353)
RemoteSpecifier.WithHopLimit(8)
LocalSpecifier := NewLocalEndpoint()
LocalSpecifier.WithIPAddress(192.0.2.22)
LocalSpecifier.WithInterface("en0")
TransportProperties := ...
SecurityParameters := ...
Preconnection := NewPreconnection(LocalSpecifier,
RemoteSpecifier,
TransportProperties,
SecurityProperties)
Connection := Preconnection.Initiate()
¶
Join an any-source multicast group as both a sender and a receiver:¶
RemoteSpecifier := NewRemoteEndpoint()
RemoteSpecifier.WithMulticastGroupIP(233.252.0.0)
RemoteSpecifier.WithPort(5353)
RemoteSpecifier.WithHopLimit(8)
LocalSpecifier := NewLocalEndpoint()
LocalSpecifier.WithAnySourceMulticastGroupIP(233.252.0.0)
LocalSpecifier.WithIPAddress(192.0.2.22)
LocalSpecifier.WithPort(5353)
LocalSpecifier.WithInterface("en0")
TransportProperties := ...
SecurityParameters := ...
Preconnection := NewPreconnection(LocalSpecifier,
RemoteSpecifier,
TransportProperties,
SecurityProperties)
Connection, Listener := Preconnection.Rendezvous()
¶
A Preconnection object holds properties reflecting the application's requirements and preferences for the transport. These include Selection Properties for selecting Protocol Stacks and paths, as well as Connection Properties and Message Properties for configuration of the detailed operation of the selected Protocol Stacks on a per-Connection and Message level.¶
The protocol(s) and path(s) selected as candidates during establishment are determined and configured using these properties. Since there could be paths over which some transport protocols are unable to operate, or Remote Endpoints that support only specific network addresses or transports, transport protocol selection is necessarily tied to path selection. This could involve choosing between multiple local interfaces that are connected to different access networks.¶
When additional information (such as Provisioning Domain (PvD) information [RFC7556]) is available about the networks over which an endpoint can operate, this can inform the selection between alternate network paths. Path information can include PMTU, set of supported DSCPs, expected usage, cost, etc. The usage of this information by the Transport Services System is generally independent of the specific mechanism/protocol used to receive the information (e.g. zero-conf, DHCP, or IPv6 RA).¶
Most Selection Properties are represented as Preferences, which can take one of five values:¶
| Preference | Effect |
|---|---|
| Require | Select only protocols/paths providing the property, fail otherwise |
| Prefer | Prefer protocols/paths providing the property, proceed otherwise |
| No Preference | No preference |
| Avoid | Prefer protocols/paths not providing the property, proceed otherwise |
| Prohibit | Select only protocols/paths not providing the property, fail otherwise |
The implementation MUST ensure an outcome that is consistent with all application requirements expressed using Require and Prohibit. While preferences expressed using Prefer and Avoid influence protocol and path selection as well, outcomes can vary given the same Selection Properties, because the available protocols and paths can differ across systems and contexts. However, implementations are RECOMMENDED to seek to provide a consistent outcome to an application, when provided with the same set of Selection Properties.¶
Note that application preferences can conflict with each other. For example, if an application indicates a preference for a specific path by specifying an interface, but also a preference for a protocol, a situation might occur in which the preferred protocol is not available on the preferred path. In such cases, applications can expect properties that determine path selection to be prioritized over properties that determine protocol selection. The transport system SHOULD determine the preferred path first, regardless of protocol preferences. This ordering is chosen to provide consistency across implementations, based on the fact that it is more common for the use of a given network path to determine cost to the user (i.e., an interface type preference might be based on a user's preference to avoid being charged more for a cellular data plan).¶
Selection and Connection Properties, as well as defaults for Message Properties, can be added to a Preconnection to configure the selection process and to further configure the eventually selected Protocol Stack(s). They are collected into a TransportProperties object to be passed into a Preconnection object:¶
TransportProperties := NewTransportProperties()¶
Individual properties are then set on the TransportProperties object. Setting a Transport Property to a value overrides the previous value of this Transport Property.¶
TransportProperties.Set(property, value)¶
To aid readability, implementations MAY provide additional convenience functions to simplify use of Selection Properties: see Appendix B.1 for examples. In addition, implementations MAY provide a mechanism to create TransportProperties objects that are preconfigured for common use cases, as outlined in Appendix B.2.¶
Transport Properties for an established Connection can be queried via the Connection object, as outlined in Section 8.¶
A Connection gets its Transport Properties either by being explicitly configured via a Preconnection, by configuration after establishment, or by inheriting them from an antecedent via cloning; see Section 7.4 for more.¶
Section 8.1 provides a list of Connection Properties, while Selection
Properties are listed in the subsections below. Selection Properties are
only considered during establishment, and can not be changed after a Connection
is established. After a Connection is established, Selection Properties can only
be read to check the properties used by the Connection. Upon reading, the
Preference type of a Selection Property changes into Boolean, where true means
that the selected Protocol Stack supports the feature or uses the path associated
with the Selection Property, and false means that the Protocol Stack does not
support the feature or use the path. Implementations
of Transport Services systems could alternatively use the two Preference values Require
and Prohibit to represent true and false, respectively.
Other types of Selection Properties remain unchanged when they are made available for
reading after a Connection is established.¶
An implementation of the Transport Services API needs to provide sensible defaults for Selection Properties. The default values for each property below represent a configuration that can be implemented over TCP. If these default values are used and TCP is not supported by a Transport Services system, then an application using the default set of Properties might not succeed in establishing a Connection. Using the same default values for independent Transport Services systems can be beneficial when applications are ported between different implementations/platforms, even if this default could lead to a Connection failure when TCP is not available. If default values other than those suggested below are used, it is RECOMMENDED to clearly document any differences.¶
This property specifies whether the application needs to use a transport protocol that ensures that all data is received at the Remote Endpoint in order without loss or duplication. When reliable data transfer is enabled, this also entails being notified when a Connection is closed or aborted.¶
This property specifies whether the application needs or prefers to use a transport protocol that preserves message boundaries.¶
This property specifies whether an application considers it useful to specify different reliability requirements for individual Messages in a Connection.¶
This property specifies whether the application wishes to use a transport protocol that can ensure that data is received by the application at the Remote Endpoint in the same order as it was sent.¶
This property specifies whether an application would like to supply a Message to the transport protocol before connection establishment that will then be reliably transferred to the Remote Endpoint before or during connection establishment. This Message can potentially be received multiple times (i.e., multiple copies of the Message data could be passed to the Remote Endpoint). See also Section 9.1.3.4.¶
This property specifies whether the application would prefer multiple Connections within a Connection Group to be provided by streams of a single underlying transport connection where possible.¶
This property specifies the application's need for protection against corruption for all data transmitted on this Connection. Disabling this property could enable the application to influence the sender checksum coverage after Connection establishment (see Section 9.1.3.6).¶
This property specifies the application's need for protection against corruption for all data received on this Connection. Disabling this property could enable the application to influence the required minimum receiver checksum coverage after Connection establishment (see Section 8.1.1).¶
This property specifies whether the application would like the Connection to be congestion controlled or not. Note that if a Connection is not congestion controlled, an application using such a Connection SHOULD itself perform congestion control in accordance with [RFC2914] or use a circuit breaker in accordance with [RFC8084], whichever is appropriate. Also note that reliability is usually combined with congestion control in protocol implementations, rendering "reliable but not congestion controlled" a request that is unlikely to succeed. If the Connection is congestion controlled, performing additional congestion control in the application can have negative performance implications.¶
This property specifies whether the application would like the Connection to send keep-alive packets or not. Note that if a Connection determines that keep-alive packets are being sent, the application SHOULD itself avoid generating additional keep-alive messages. Note that when supported, the system will use the default period for generation of the keep alive-packets. (See also Section 8.1.4).¶
interface¶
Set of (Preference, Enumeration)¶
Empty (not setting a preference for any interface)¶
This property allows the application to select any specific network interfaces
or categories of interfaces it wants to Require, Prohibit, Prefer, or
Avoid. Note that marking a specific interface as Require strictly limits path
selection to that single interface, and often leads to less flexible and resilient
connection establishment.¶
In contrast to other Selection Properties, this property is a set of tuples of (Enumerated) interface identifier and preference. It can either be implemented directly as such, or for making one preference available for each interface and interface type available on the system.¶
The set of valid interface types is implementation- and system-specific. For
example, on a mobile device, there could be Wi-Fi and Cellular interface types
available; whereas on a desktop computer, Wi-Fi and Wired
Ethernet interface types might be available. An implementation should provide all types
that are supported on the local system, to allow
applications to be written generically. For example, if a single implementation
is used on both mobile devices and desktop devices, it ought to define the
Cellular interface type for both systems, since an application might wish to
always prohibit cellular.¶
The set of interface types is expected to change over time as new access technologies become available. The taxonomy of interface types on a given Transport Services system is implementation-specific.¶
Interface types SHOULD NOT be treated as a proxy for properties of interfaces such as metered or unmetered network access. If an application needs to prohibit metered interfaces, this should be specified via Provisioning Domain attributes (see Section 6.2.12) or another specific property.¶
Note that this property is not used to specify an interface scope zone for a particular Endpoint. Section 6.1.2 provides details about how to qualify endpoint candidates on a per-interface basis.¶
pvd¶
Set of (Preference, Enumeration)¶
Empty (not setting a preference for any PvD)¶
Similar to interface (see Section 6.2.11), this property
allows the application to control path selection by selecting which specific
Provisioning Domain (PvD) or categories of PVDs it wants to
Require, Prohibit, Prefer, or Avoid. Provisioning Domains define
consistent sets of network properties that might be more specific than network
interfaces [RFC7556].¶
As with interface instances and types, this property is a set of tuples of (Enumerated) PvD identifier and preference. It can either be implemented directly as such, or for making one preference available for each interface and interface type available on the system.¶
The identification of a specific PvD is implementation- and system-specific. [RFC8801] defines how to use an FQDN to identify a PvD when advertised by a network, but systems might also use other locally-relevant identifiers such as string names or Integers to identify PvDs. As with requiring specific interfaces, requiring a specific PvD strictly limits the path selection.¶
Categories or types of PvDs are also defined to be implementation- and system-specific. These can be useful to identify a service that is provided by a PvD. For example, if an application wants to use a PvD that provides a Voice-Over-IP service on a Cellular network, it can use the relevant PvD type to require a PvD that provides this service, without needing to look up a particular instance. While this does restrict path selection, it is broader than requiring specific PvD instances or interface instances, and should be preferred over these options.¶
useTemporaryLocalAddress¶
Preference¶
Avoid for Listeners and Rendezvous Connections. Prefer for other Connections.¶
This property allows the application to express a preference for the use of temporary local addresses, sometimes called "privacy" addresses [RFC8981]. Temporary addresses are generally used to prevent linking connections over time when a stable address, sometimes called "permanent" address, is not needed. There are some caveats to note when specifying this property. First, if an application Requires the use of temporary addresses, the resulting Connection cannot use IPv4, because temporary addresses do not exist in IPv4. Second, temporary local addresses might involve trading off privacy for performance. For instance, temporary addresses (e.g., [RFC8981]) can interfere with resumption mechanisms that some protocols rely on to reduce initial latency.¶
multipath¶
Enumeration¶
Disabled for Connections created through initiate and rendezvous, Passive for Listeners¶
This property specifies whether and how applications want to take advantage of transferring data across multiple paths between the same end hosts. Using multiple paths allows Connections to migrate between interfaces or aggregate bandwidth as availability and performance properties change. Possible values are:¶
The Connection will not use multiple paths once established, even if the chosen transport supports using multiple paths.¶
The Connection will negotiate the use of multiple paths if the chosen transport supports this.¶
The Connection will support the use of multiple paths if the Remote Endpoint requests it.¶
The policy for using multiple paths is specified using the separate multipathPolicy property, see Section 8.1.7 below.
To enable the peer endpoint to initiate additional paths towards a local address other than the one initially used, it is necessary to set the advertisesAltaddr property (see Section 6.2.15 below).¶
Setting this property to Active can have privacy implications: It enables the transport to establish connectivity using alternate paths that might result in users being linkable across the multiple paths, even if the advertisesAltaddr property (see Section 6.2.15 below) is set to false.¶
Note that Multipath Transport has no corresponding Selection Property of type Preference.
Enumeration values other than Disabled are interpreted as a preference for choosing protocols that can make use of multiple paths.
The Disabled value implies a requirement not to use multiple paths in parallel but does not prevent choosing a protocol that is capable of using multiple paths, e.g., it does not prevent choosing TCP, but prevents sending the MP_CAPABLE option in the TCP handshake.¶
This property specifies whether alternative addresses, e.g., of other interfaces, ought to be advertised to the peer endpoint by the Protocol Stack. Advertising these addresses enables the peer endpoint to establish additional connectivity, e.g., for Connection migration or using multiple paths.¶
Note that this can have privacy implications because it might result in users being linkable across the multiple paths.
Also, note that setting this to false does not prevent the local Transport Services system from establishing connectivity using alternate paths (see Section 6.2.14 above); it only prevents proactive advertisement of addresses.¶
This property specifies whether an application wants to use the Connection for sending and/or receiving data. Possible values are:¶
The Connection must support sending and receiving data¶
The Connection must support sending data, and the application cannot use the Connection to receive any data¶
The Connection must support receiving data, and the application cannot use the Connection to send any data¶
Since unidirectional communication can be supported by transports offering bidirectional communication, specifying unidirectional communication might cause a transport stack that supports bidirectional communication to be selected.¶
This property specifies whether an application considers it useful to be
informed when an ICMP error message arrives that does not force termination of a
connection. When set to true, received ICMP errors are available as
SoftError events, see Section 8.3.1. Note that even if a protocol supporting this property is selected,
not all ICMP errors will necessarily be delivered, so applications cannot rely
upon receiving them [RFC8085].¶
The most common client-server communication pattern involves the
client actively opening a Connection, then sending data to the server. The
server listens (passive open), reads, and then answers. This property
specifies whether an application wants to diverge from this pattern -- either
by actively opening with Initiate, immediately followed by reading, or passively opening with Listen,
immediately followed by writing. This property is ignored when establishing
connections using Rendezvous.
Requiring this property limits the choice of mappings to underlying protocols,
which can reduce
efficiency. For example, it prevents the Transport Services system from mapping
Connections to SCTP streams, where
the first transmitted data takes the role of an active open signal.¶
Most security parameters, e.g., TLS ciphersuites, local identity and private key, etc., can be configured statically. Others are dynamically configured during Connection establishment. Security parameters and callbacks are partitioned based on their place in the lifetime of Connection establishment. Similar to Transport Properties, both parameters and callbacks are inherited during cloning (see Section 7.4).¶
This document specifies an abstract API, which could appear to conflict with the need for security parameters to be unambiguous. The Transport Services System SHOULD provide reasonable, secure defaults for each enumerated security parameter, such that users of the system only need to specify parameters required to establish a secure connection (e.g., 'server-certificate', 'client-certificate'). Specifying specific security parameters from enumerated values (e.g., specific ciphersuites) might constrain the Transport Protocols that can be selected during connection establishment.¶
Except as noted below, as with the rest of the Transport Services API, exact names of parameters and/or values of enumerations (e.g., ciphersuites) used in the security parameters are system and implementation specific, and ought to be chosen to follow the principle of least surprise for users of the platform / language environment in question.¶
Common security parameters such as TLS ciphersuites are known to implementations. Applications SHOULD use common safe defaults for these values whenever possible. However, as discussed in [RFC8922], many transport security protocols require specific security parameters and constraints from the client at the time of configuration and actively during a handshake.¶
The configuration parameters need to be specified in the pre-connection phase and are created as follows:¶
SecurityParameters := NewSecurityParameters()¶
Security configuration parameters and sample usage follow:¶
One or more certificate bundles identifying the Local Endpoint, whether as a server certificate or a client certificate. Multiple bundles may be provided to allow selection among different protocol stacks that may require differently formatted bundles. The form and format of the certificate bundle is implementation-specific. Note that if the private keys associated with a bundle are not available, e.g., since they are stored in hardware security modules (HSMs), handshake callbacks are necessary. See below for details.¶
SecurityParameters.Set(server-certificate, myCertificateBundle[]) SecurityParameters.Set(client-certificate, myCertificateBundle[])¶
One or more certificate chains to use as pinned server certificates, such that connecting will fail if the presented server certificate does not match one of the supplied pinned certificates. The form and format of the certificate chain is implementation-specific.¶
SecurityParameters.Set(pinned-server-certificate, yourCertificateChain[])¶
Application-layer protocol negotiation (ALPN) values: used to indicate which application-layer protocols are negotiated by the security protocol layer. See [ALPN] for definition of the ALPN field. Note that the Transport Services System can provide ALPN values automatically, based on the protocols being used, if not explicitly specified by the application.¶
SecurityParameters.Set(alpn, "h2")¶
Supported groups, ciphersuites, algorithms: Used to restrict what parameters are used by underlying transport security protocols. When not specified, these algorithms should use known and safe defaults for the system.¶
SecurityParameters.Set(supported-group, "secp256r1") SecurityParameters.Set(ciphersuite, "TLS_AES_128_GCM_SHA256") SecurityParameters.Set(signature-algorithm, "ecdsa_secp256r1_sha256")¶
Session cache management: Used to tune session cache capacity, lifetime, and other policies.¶
SecurityParameters.Set(max-cached-sessions, 16) SecurityParameters.Set(cached-session-lifetime-seconds, 3600)¶
Pre-Shared Key import: Used to install pre-shared keying material established out-of-band. Each instance of pre-shared keying material is associated with some identity that typically identifies its use or has some protocol-specific meaning to the Remote Endpoint. Note that use of a pre-shared key will tend to select a single security protocol, and therefore directly select a single underlying protocol stack.¶
SecurityParameters.Set(pre-shared-key, key, myIdentity)¶
Connections that use Transport Services SHOULD use security in general. However, for compatibility with endpoints that do not support transport security protocols (such as a TCP endpoint that does not support TLS), applications can initialize their security parameters to indicate that security can be disabled, or can be opportunistic. If security is disabled, the Transport Services system will not attempt to add transport security automatically. If security is opportunistic, it will allow Connections without transport security, but will still attempt to use unauthenticated security if available.¶
SecurityParameters := NewDisabledSecurityParameters() SecurityParameters := NewOpportunisticSecurityParameters()¶
Representation of security parameters in implementations ought to parallel that chosen for Transport Property names as suggested in Section 5.¶
Security decisions, especially pertaining to trust, are not static. Once configured, parameters can also be supplied during Connection establishment. These are best handled as client-provided callbacks. Callbacks block the progress of the Connection establishment, which distinguishes them from other events in the transport system. How callbacks and events are implemented is specific to each implementation. Security handshake callbacks that could be invoked during Connection establishment include:¶
Trust verification callback: Invoked when a Remote Endpoint's trust must be verified before the handshake protocol can continue. For example, the application could verify an X.509 certificate as described in [RFC5280].¶
TrustCallback := NewCallback({
// Handle trust, return the result
})
SecurityParameters.SetTrustVerificationCallback(TrustCallback)
¶
Identity challenge callback: Invoked when a private key operation is required, e.g., when local authentication is requested by a Remote Endpoint.¶
ChallengeCallback := NewCallback({
// Handle challenge
})
SecurityParameters.SetIdentityChallengeCallback(ChallengeCallback)
¶
Before a Connection can be used for data transfer, it needs to be established.
Establishment ends the pre-establishment phase; all transport properties and
cryptographic parameter specification must be complete before establishment,
as these will be used to select candidate Paths and Protocol Stacks
for the Connection. Establishment can be active, using the Initiate action;
passive, using the Listen action; or simultaneous for peer-to-peer, using
the Rendezvous action. These actions are described in the subsections below.¶
Active open is the action of establishing a Connection to a Remote Endpoint presumed
to be listening for incoming Connection requests. Active open is used by clients in
client-server interactions. Active open is supported by the Transport Services API through the
Initiate action:¶
Connection := Preconnection.Initiate(timeout?)¶
The timeout parameter specifies how long to wait before aborting Active open.
Before calling Initiate, the caller must have populated a Preconnection
object with a Remote Endpoint object to identify the endpoint, optionally a Local Endpoint
object (if not specified, the system will attempt to determine a
suitable Local Endpoint), as well as all properties
necessary for candidate selection.¶
The Initiate action returns a Connection object. Once Initiate has been
called, any changes to the Preconnection MUST NOT have any effect on the
Connection. However, the Preconnection can be reused, e.g., to Initiate
another Connection.¶
Once Initiate is called, the candidate Protocol Stack(s) can cause one or more
candidate transport-layer connections to be created to the specified Remote
Endpoint. The caller could immediately begin sending Messages on the Connection
(see Section 9.2) after calling Initiate; note that any data marked as "safely replayable" that is sent
while the Connection is being established could be sent multiple times or on
multiple candidates.¶
The following events can be sent by the Connection after Initiate is called:¶
Connection -> Ready<>¶
The Ready event occurs after Initiate has established a transport-layer
connection on at least one usable candidate Protocol Stack over at least one
candidate Path. No Receive events (see Section 9.3) will occur before
the Ready event for Connections established using Initiate.¶
Connection -> EstablishmentError<reason?>¶
An EstablishmentError occurs either when the set of transport properties and security
parameters cannot be fulfilled on a Connection for initiation (e.g., the set of
available Paths and/or Protocol Stacks meeting the constraints is empty) or
reconciled with the Local and/or Remote Endpoints; when a remote Endpoint Identifier
cannot be resolved; or when no transport-layer connection can be established to
the Remote Endpoint (e.g., because the Remote Endpoint is not accepting
connections, the application is prohibited from opening a Connection by the
operating system, or the establishment attempt has timed out for any other reason).¶
Connection establishment and transmission of the first Message can be combined in a single action (Section 9.2.5).¶
Passive open is the action of waiting for Connections from Remote Endpoints,
commonly used by servers in client-server interactions. Passive open is
supported by the Transport Services API through the Listen action and returns a Listener object:¶
Listener := Preconnection.Listen()¶
Before calling Listen, the caller must have initialized the Preconnection
during the pre-establishment phase with a Local Endpoint object, as well
as all properties necessary for Protocol Stack selection. A Remote Endpoint
can optionally be specified, to constrain what Connections are accepted.¶
The Listen action returns a Listener object. Once Listen has been called,
any changes to the Preconnection MUST NOT have any effect on the Listener. The
Preconnection can be disposed of or reused, e.g., to create another Listener.¶
Listener.Stop()¶
Listening continues until the global context shuts down, or until the Stop action is performed on the Listener object.¶
Listener -> ConnectionReceived<Connection>¶
The ConnectionReceived event occurs when a Remote Endpoint has established or cloned (e.g., by creating a new stream in a multi-stream transport; see Section 7.4) a
transport-layer connection to this Listener (for Connection-oriented
transport protocols), or when the first Message has been received from the
Remote Endpoint (for Connectionless protocols or streams of a multi-streaming transport), causing a new Connection to be
created. The resulting Connection is contained within the ConnectionReceived
event, and is ready to use as soon as it is passed to the application via the
event.¶
Listener.SetNewConnectionLimit(value)¶
If the caller wants to rate-limit the number of inbound Connections that will be delivered,
it can set a cap using SetNewConnectionLimit. This mechanism allows a server to
protect itself from being drained of resources. Each time a new Connection is delivered
by the ConnectionReceived event, the value is automatically decremented. Once the
value reaches zero, no further Connections will be delivered until the caller sets the
limit to a higher value. By default, this value is Infinite. The caller is also able to reset
the value to Infinite at any point.¶
Listener -> EstablishmentError<reason?>¶
An EstablishmentError occurs either when the Properties and security parameters of the Preconnection cannot be fulfilled for listening or cannot be reconciled with the Local Endpoint (and/or Remote Endpoint, if specified), when the Local Endpoint (or Remote Endpoint, if specified) cannot
be resolved, or when the application is prohibited from listening by policy.¶
Listener -> Stopped<>¶
A Stopped event occurs after the Listener has stopped listening.¶
Simultaneous peer-to-peer Connection establishment is supported by the
Rendezvous action:¶
Preconnection.Rendezvous()¶
A Preconnection object used in a Rendezvous MUST have both the
Local Endpoint candidates and the Remote Endpoint candidates specified,
along with the Transport Properties and security parameters needed for
Protocol Stack selection, before the Rendezvous action is initiated.¶
The Rendezvous action listens on the Local Endpoint
candidates for an incoming Connection from the Remote Endpoint candidates,
while also simultaneously trying to establish a Connection from the Local
Endpoint candidates to the Remote Endpoint candidates.¶
If there are multiple Local Endpoints or Remote Endpoints configured, then
initiating a Rendezvous action will cause the Transport Services
Implementation to systematically probe the reachability
of those endpoint candidates following an approach such as that used in
Interactive Connectivity Establishment (ICE) [RFC8445].¶
If the endpoints are suspected to be behind a NAT, and the Local Endpoint
supports a method of discovering NAT bindings, such as Session Traversal
Utilities for NAT (STUN) [RFC8489] or Traversal Using Relays around NAT
(TURN) [RFC8656], then the Resolve action on the Preconnection can be
used to discover such bindings:¶
[]LocalEndpoint, []RemoteEndpoint := Preconnection.Resolve()¶
The Resolve call returns lists of Local Endpoints and Remote Endpoints
that represent the concrete addresses, local and server reflexive, on which
a Rendezvous for the Preconnection will listen for incoming Connections,
and to which it will attempt to establish Connections.¶
Note that the set of Local Endpoints returned by Resolve might or might not
contain information about all possible local interfaces depending on how the
Preconnection is configured. The set of available local interfaces can also
change over time so care needs to be taken when using stored interface names.¶
An application that uses Rendezvous to establish a peer-to-peer Connection
in the presence of NATs will configure the Preconnection object with at least
one Local Endpoint that supports NAT binding discovery. It will then Resolve
the Preconnection, and pass the resulting list of Local Endpoint candidates to
the peer via a signalling protocol, for example as part of an ICE [RFC8445]
exchange within SIP [RFC3261] or WebRTC [RFC7478]. The peer will then,
via the same signalling channel, return the Remote Endpoint candidates.
The set of Remote Endpoint candidates are then configured onto the Preconnection:¶
Preconnection.AddRemote([]RemoteEndpoint)¶
The Rendezvous action is initiated, and causes the Transport Services
Implementation to begin connectivity checks, once the application has
added both the Local Endpoint candidates and the Remote Endpoint candidates
retrieved from the peer via the signalling channel to the Preconnection.¶
If successful, the Rendezvous action returns a Connection object via a
RendezvousDone<> event:¶
Preconnection -> RendezvousDone<Connection>¶
The RendezvousDone<> event occurs when a Connection is established with the
Remote Endpoint. For Connection-oriented transports, this occurs when the
transport-layer connection is established; for Connectionless transports,
it occurs when the first Message is received from the Remote Endpoint. The
resulting Connection is contained within the RendezvousDone<> event, and is
ready to use as soon as it is passed to the application via the event.
Changes made to a Preconnection after Rendezvous has been called MUST
NOT have any effect on existing Connections.¶
An EstablishmentError occurs either when the Properties and Security
Parameters of the Preconnection cannot be fulfilled for rendezvous or
cannot be reconciled with the Local and/or Remote Endpoints, when the Local
Endpoint or Remote Endpoint cannot be resolved, when no transport-layer
connection can be established to the Remote Endpoint, or when the
application is prohibited from rendezvous by policy:¶
Preconnection -> EstablishmentError<reason?>¶
Connection Groups can be created using the Clone action:¶
Connection := Connection.Clone(framer?, connectionProperties?)¶
Calling Clone on a Connection yields a Connection Group containing two Connections: the parent
Connection on which Clone was called, and a resulting cloned Connection.
The new Connection is actively opened, and it will locally send a Ready event or an EstablishmentError event.
Calling Clone on any of these Connections adds another Connection to
the Connection Group. Connections in a Connection Group share all
Connection Properties except connPriority (see Section 8.1.2),
and these Connection Properties are entangled: Changing one of the
Connection Properties on one Connection in the Connection Group
automatically changes the Connection Property for all others. For example, changing
connTimeout (see
Section 8.1.3) on one Connection in a Connection Group will automatically
make the same change to this Connection Property for all other Connections in the Connection Group.
Like all other Properties, connPriority is copied
to the new Connection when calling Clone, but in this case, a later change to the
connPriority on one Connection does not change it on the
other Connections in the same Connection Group.¶
The optional connectionProperties parameter allows passing
Transport Properties that control the behavior of the underlying stream or connection to be created, e.g., Protocol-specific Properties to request specific stream IDs for SCTP or QUIC.¶
Message Properties set on a Connection also apply only to that Connection.¶
A new Connection created by Clone can have a Message Framer assigned via the optional
framer parameter of the Clone action. If this parameter is not supplied, the
stack of Message Framers associated with a Connection is copied to
the cloned Connection when calling Clone. Then, a cloned Connection
has the same stack of Message Framers as the Connection from which they
are cloned, but these Framers can internally maintain per-Connection state.¶
It is also possible to check which Connections belong to the same Connection Group.
Calling GroupedConnections on a specific Connection returns a set of all Connections
in the same group.¶
[]Connection := Connection.GroupedConnections()¶
Connections will belong to the same group if the application previously called Clone.
Passive Connections can also be added to the same group -- e.g., when a Listener
receives a new Connection that is just a new stream of an already active multi-streaming
protocol instance.¶
If the underlying protocol supports multi-streaming, it is natural to use this
functionality to implement Clone. In that case, Connections in a Connection Group are
multiplexed together, giving them similar treatment not only inside Endpoints,
but also across the end-to-end Internet path.¶
Note that calling Clone can result in on-the-wire signaling, e.g., to open a new
transport connection, depending on the underlying Protocol Stack. When Clone leads to
the opening of multiple such connections,
the Transport Services system will ensure consistency of
Connection Properties by uniformly applying them to all underlying connections
in a group. Even in such a case, there are possibilities for a Transport Services system
to implement prioritization within a Connection Group [TCP-COUPLING] [RFC8699].¶
Attempts to clone a Connection can result in a CloneError:¶
Connection -> CloneError<reason?>¶
A CloneError can also occur later, after Clone was successfully called. In this case,
it informs the application that the Connection that sends the CloneError is no longer a
part of any Connection Group. For example, this can occur when the Transport Services
system is unable to implement entanglement (a Connection Property was changed on a different
Connection in the Connection Group, but this change could not be successfully applied
to the Connection that sends the CloneError).¶
The connPriority Connection Property operates on Connections in a Connection Group
using the same approach as in Section 9.1.3.2: when allocating available network
capacity among Connections in a Connection Group, sends on Connections with
numerically lower Priority values will be prioritized over sends on Connections that have
numerically higher Priority values. Capacity will be shared among these Connections according to
the connScheduler property (Section 8.1.5).
See Section 9.2.6 for more.¶
Transport protocols that are explicitly multipath aware are expected to automatically
manage the set of Remote Endpoints that they are communicating with, and the paths to
those endpoints. A PathChange<> event, described in Section 8.3.2, will be
generated when the path changes.¶
In some cases, however, it is necessary to explicitly indicate to a Connection that a new Remote Endpoint has become available for use, or to indicate that a Remote Endpoint is no longer available. This is most common in the case of peer to peer connections using Trickle ICE [RFC8838].¶
The AddRemote action can be used to add one or more new Remote Endpoints
to a Connection:¶
Connection.AddRemote([]RemoteEndpoint)¶
Endpoints that are already known to the Connection are ignored. A call to
AddRemote makes the new Remote Endpoints available to the Connection,
but whether the Connection makes use of those Endpoints will depend on the
underlying transport protocol.¶
Similarly, the RemoveRemote action can be used to tell a Connection to
stop using one or more Remote Endpoints:¶
Connection.RemoveRemote([]RemoteEndpoint)¶
Removing all known Remote Endpoints can have the effect of aborting the connection. The effect of removing the active Remote Endpoint(s) depends on the underlying transport: multipath aware transports might be able to switch to a new path if other reachable Remote Endpoints exist, or the connection might abort.¶
Similarly, the AddLocal and RemoveLocal actions can be used to add
and remove Local Endpoints to/from a Connection.¶
During pre-establishment and after establishment, (Pre-)Connections can be configured and queried using Connection
Properties, and asynchronous information could be available about the state of the
Connection via SoftError events.¶
Connection Properties represent the configuration and state of the selected Protocol Stack(s) backing a Connection. These Connection Properties can be generic, applying regardless of transport protocol, or specific, applicable to a single implementation of a single transport Protocol Stack. Generic Connection Properties are defined in Section 8.1 below.¶
Protocol-specific Properties are defined in a transport- and implementation-specific way to permit more specialized protocol features to be used. Too much reliance by an application on Protocol-specific Properties can significantly reduce the flexibility of a transport services system to make appropriate selection and configuration choices. Therefore, it is RECOMMENDED that Generic Connection Properties are used for properties common across different protocols and that Protocol-specific Connection Properties are only used where specific protocols or properties are necessary.¶
The application can set and query Connection Properties on a per-Connection
basis. Connection Properties that are not read-only can be set during
pre-establishment (see Section 6.2), as well as on Connections directly using
the SetProperty action:¶
ErrorCode := Connection.SetProperty(property, value)¶
If an error is encountered in setting a property (for example, if the application tries to set a TCP-specific property on a Connection that is not using TCP), the application MUST be informed about this error via the ErrorCode Object. Such errors MUST NOT cause the Connection to be terminated.
Note that changing one of the Connection Properties on one Connection in a Connection Group
will also change it for all other Connections of that group; see further Section 7.4.¶
At any point, the application can query Connection Properties.¶
ConnectionProperties := Connection.GetProperties() value := ConnectionProperties.Get(property) if ConnectionProperties.Has(boolean_or_preference_property) then ...¶
Depending on the status of the Connection, the queried Connection Properties will include different information:¶
The Connection state, which can be one of the following: Establishing, Established, Closing, or Closed (see Section 8.1.11.1).¶
Whether the Connection can be used to send data (see Section 8.1.11.2).
A Connection can not be used
for sending if the Connection was created with the Selection Property
direction set to unidirectional receive or if a Message
marked as Final was sent over this Connection. See also Section 9.1.3.5.¶
Whether the Connection can be used to receive data (see Section 8.1.11.3).
A Connection cannot be
used for receiving if the Connection was created with the Selection Property
direction set to unidirectional send or if a Message
marked as Final was received. See Section 9.3.3.3. The latter
is only supported by certain transport protocols, e.g., by TCP as half-closed
connection.¶
For Connections that are Established, Closing, or Closed:
Connection Properties (Section 8.1) of the
actual protocols that were selected and instantiated, and Selection
Properties that the application specified on the Preconnection.
Selection Properties of type Preference will be exposed as boolean values
indicating whether or not the property applies to the selected transport.
Note that the instantiated Protocol Stack might not match all
Protocol Selection Properties that the application specified on the
Preconnection.¶
For Connections that are Established: Transport Services system implementations ought to provide information concerning the path(s) used by the Protocol Stack. This can be derived from local PVD information, measurements by the Protocol Stack, or other sources. For example, a Transport System that is configured to receive and process PVD information [RFC7556] could also provide network configuration information for the chosen path(s).¶
Generic Connection Properties are defined independent of the chosen Protocol Stack and therefore available on all Connections.¶
Many Connection Properties have a corresponding Selection Property that enables applications to express their preference for protocols providing a supporting transport feature.¶
If this property is an Integer, it specifies the minimum number of bytes in a received
Message that need to be covered by a checksum.
A receiving endpoint will not forward Messages that have less coverage
to the application. The application is responsible for handling
any corruption within the non-protected part of the Message [RFC8085].
A special value of 0 means that a received packet might also have a zero checksum field,
and the enumerated value Full Coverage means
that the entire Message needs to be protected by a checksum. An implementation
is supposed to express Full Coverage in an environment-typical way, e.g., as a Union type or special value.¶
This property is a non-negative Integer representing the priority of this Connection relative to other Connections in the same Connection Group. A numerically lower value reflects a higher priority. It has no effect on Connections not part of a Connection Group. As noted in Section 7.4, this property is not entangled when Connections are cloned, i.e., changing the Priority on one Connection in a Connection Group does not change it on the other Connections in the same Connection Group. No guarantees of a specific behavior regarding Connection Priority are given; a Transport Services system could ignore this property. See Section 9.2.6 for more details.¶
If this property is Numeric, it specifies how long to wait before deciding that an active Connection has
failed when trying to reliably deliver data to the Remote Endpoint. Adjusting this property
will only take effect when the underlying stack supports reliability. If this property has the enumerated
value Disabled, it means that no timeout is scheduled. A Transport Services API
could express Disabled in an environment-typical way, e.g., as a Union type or special value.¶
A Transport Services API can request a protocol that supports sending keep alive packets (Section 6.2.10).
If this property is Numeric, it specifies the maximum length of time an idle Connection (one for which no transport
packets have been sent) ought to wait before
the Local Endpoint sends a keep-alive packet to the Remote Endpoint. Adjusting this property
will only take effect when the underlying stack supports sending keep-alive packets.
Guidance on setting this value for connection-less transports is
provided in [RFC8085].
A value greater than the Connection timeout (Section 8.1.3) or the enumerated value Disabled will disable the sending of keep-alive packets. A Transport Services API
could express Disabled in an environment-typical way, e.g., as a Union type or special value.¶
connScheduler¶
Enumeration¶
Weighted Fair Queueing (see Section 3.6 of [RFC8260])¶
This property specifies which scheduler is used among Connections within a Connection Group to apportion the available capacity according to Connection priorities (see Section 7.4 and Section 8.1.2). A set of schedulers is described in [RFC8260].¶
This property specifies the desired network treatment for traffic sent by the application and the tradeoffs the application is prepared to make in path and protocol selection to receive that desired treatment. When the capacity profile is set to a value other than Default, the Transport Services system SHOULD select paths and configure protocols to optimize the tradeoff between delay, delay variation, and efficient use of the available capacity based on the capacity profile specified. How this is realized is implementation-specific. The capacity profile MAY also be used to set markings on the wire for Protocol Stacks supporting this. Recommendations for use with DSCP are provided below for each profile; note that when a Connection is multiplexed, the guidelines in Section 6 of [RFC7657] apply.¶
The following values are valid for the capacity profile:¶
The application provides no information about its expected capacity profile. Transport Services systems that map the requested capacity profile onto per-connection DSCP signaling SHOULD assign the DSCP Default Forwarding [RFC2474] Per Hop Behaviour (PHB).¶
The application is not interactive. It expects to send and/or receive data without any urgency. This can, for example, be used to select Protocol Stacks with scavenger transmission control and/or to assign the traffic to a lower-effort service. Transport Services systems that map the requested capacity profile onto per-connection DSCP signaling SHOULD assign the DSCP Less than Best Effort [RFC8622] PHB.¶
The application is interactive, and prefers loss to latency. Response time SHOULD be optimized at the expense of delay variation and efficient use of the available capacity when sending on this Connection. This can be used by the system to disable the coalescing of multiple small Messages into larger packets (Nagle's algorithm); to prefer immediate acknowledgment from the peer endpoint when supported by the underlying transport; and so on. Transport Services systems that map the requested capacity profile onto per-connection DSCP signaling without multiplexing SHOULD assign a DSCP Assured Forwarding (AF41,AF42,AF43,AF44) [RFC2597] PHB. Inelastic traffic that is expected to conform to the configured network service rate could be mapped to the DSCP Expedited Forwarding [RFC3246] or [RFC5865] PHBs.¶
The application prefers loss to latency, but is not interactive. Response time SHOULD be optimized at the expense of delay variation and efficient use of the available capacity when sending on this Connection. Transport system implementations that map the requested capacity profile onto per-connection DSCP signaling without multiplexing SHOULD assign a DSCP Assured Forwarding (AF21,AF22,AF23,AF24) [RFC2597] PHB.¶
The application expects to send/receive data at a constant rate after Connection establishment. Delay and delay variation SHOULD be minimized at the expense of efficient use of the available capacity. This implies that the Connection might fail if the Path is unable to maintain the desired rate. A transport can interpret this capacity profile as preferring a circuit breaker [RFC8084] to a rate-adaptive congestion controller. Transport system implementations that map the requested capacity profile onto per-connection DSCP signaling without multiplexing SHOULD assign a DSCP Assured Forwarding (AF31,AF32,AF33,AF34) [RFC2597] PHB.¶
The application expects to send/receive data at the maximum rate allowed by its congestion controller over a relatively long period of time. Transport Services systems that map the requested capacity profile onto per-connection DSCP signaling without multiplexing SHOULD assign a DSCP Assured Forwarding (AF11,AF12,AF13,AF14) [RFC2597] PHB per Section 4.8 of [RFC4594].¶
The capacity profile for a selected Protocol Stack may be modified on a per-Message basis using the Transmission Profile Message Property; see Section 9.1.3.8.¶
This property specifies the local policy for transferring data across multiple paths between the same end hosts if Multipath Transport is not set to Disabled (see Section 6.2.14). Possible values are:¶
The Connection ought only to attempt to migrate between different paths when the original path is lost or becomes unusable. The thresholds used to declare a path unusable are implementation specific.¶
The Connection ought only to attempt to minimize the latency for interactive traffic patterns by transmitting data across multiple paths when this is beneficial. The goal of minimizing the latency will be balanced against the cost of each of these paths. Depending on the cost of the lower-latency path, the scheduling might choose to use a higher-latency path. Traffic can be scheduled such that data may be transmitted on multiple paths in parallel to achieve a lower latency. The specific scheduling algorithm is implementation-specific.¶
The Connection ought to attempt to use multiple paths in parallel to maximize available capacity and possibly overcome the capacity limitations of the individual paths. The actual strategy is implementation specific.¶
Note that this is a local choice – the Remote Endpoint can choose a different policy.¶
minSendRate / minRecvRate / maxSendRate / maxRecvRate¶
Numeric (positive) or Unlimited / Numeric (positive) or Unlimited / Numeric (positive) or Unlimited / Numeric (positive) or Unlimited¶
Unlimited / Unlimited / Unlimited / Unlimited¶
Numeric values of these properties specify an upper-bound rate that a transfer is not expected to
exceed (even if flow control and congestion control allow higher rates), and/or a
lower-bound application-layer rate below which the application does not deem
it will be useful. These rate values are measured at the application layer, i.e. do not consider the header overhead
from protocols used by the Transport Services system. The values are specified in bits per second,
and assumed to be measured over one-second time intervals. E.g., specifying a maxSendRate of X bits per second
means that, from the moment at which the property value is chosen, not more than X bits will be send in any
following second. The enumerated value Unlimited indicates that no bound is specified.
A Transport Services API could express Unlimited in an environment-typical way, e.g., as a Union type or special value.¶
If this property is Numeric, it controls the number of Connections that can be accepted from
a peer as new members of the Connection's group. Similar to SetNewConnectionLimit,
this limits the number of ConnectionReceived events that will occur, but constrained
to the group of the Connection associated with this property. For a multi-streaming transport,
this limits the number of allowed streams. A Transport Services API
could express Unlimited in an environment-typical way, e.g., as a Union type or special value.¶
When set to true, this property will initiate new Connections using as little
cached information (such as session tickets or cookies) as possible from
previous Connections that are not in the same Connection Group. Any state generated by this
Connection will only be shared with Connections in the same Connection Group. Cloned Connections
will use saved state from within the Connection Group.
This is used for separating Connection Contexts as specified in Section 4.2.3 of [I-D.ietf-taps-arch].¶
Note that this does not guarantee no leakage of information, as implementations might not be able to fully isolate all caches (e.g. RTT estimates). Note that this property could degrade Connection performance.¶
The following generic Connection Properties are read-only, i.e. they cannot be changed by an application.¶
This property informs about the current state of the Connection. Possible values are: Establishing, Established, Closing or Closed; for more details on Connection state, see Section 11.¶
This property can be queried to learn whether the Connection can be used to send data.¶
This property can be queried to learn whether the Connection can be used to receive data.¶
This property, if applicable, represents the maximum Message size that can be
sent without incurring network-layer fragmentation at the sender.
It is specified as a number of bytes and is less than or equal to the
Maximum Message Size on Send.
It exposes a readable value to the application
based on the Maximum Packet Size (MPS). The value of this property can change over time (and can be updated by Datagram PLPMTUD [RFC8899]).
This value allows a sending stack to avoid unwanted fragmentation at the
network-layer or segmentation by the transport layer before
choosing the message size and/or after a SendError occurs indicating
an attempt to send a Message that is too large. A Transport Services API
could express Not applicable in an environment-typical way, e.g., as a Union type or special value (e.g., 0).¶
This property represents the maximum Message size that an application can send. It is specified as the number of bytes. A value of 0 indicates that sending is not possible.¶
This property represents the maximum Message size that an application can receive. It is specified as the number of bytes. A value of 0 indicates that receiving is not possible.¶
These properties specify configurations for the TCP User Timeout Option (UTO). This is a TCP-specific property, that is only used in the case that TCP becomes the chosen transport protocol and useful only if TCP is implemented in the Transport Services system. Protocol-specific options could also be defined for other transport protocols.¶
These are included here because the feature Suggest
timeout to the peer is part of the minimal set of transport services
[RFC8923], where this feature was categorized as "functional".
This means that when a Transport Services system offers this feature,
the Transport Services API has to expose an interface to the application. Otherwise, the implementation might
violate assumptions by the application, which could cause the application to
fail.¶
All of the below properties are optional (e.g., it is possible to specify User Timeout Enabled as true,
but not specify an Advertised User Timeout value; in this case, the TCP default will be used).
These properties reflect the API extension specified in Section 3 of [RFC5482].¶
This time value is advertised via the TCP User Timeout Option (UTO) [RFC5482] to the Remote Endpoint which can use it to adapt its own Timeout for aborting Connection (see Section 8.1.3) value.¶
This property controls whether the TCP UTO option is enabled for a connection. This applies to both sending and receiving.¶
This property controls whether the TCP connTimeout (see Section 8.1.3)
can be changed
based on a UTO option received from the remote peer. This boolean becomes false when
connTimeout (see Section 8.1.3) is used.¶
During the lifetime of a Connection there are events that can occur when configured.¶
Asynchronous introspection is also possible, via the SoftError event. This event
informs the application about the receipt and contents of an ICMP error message related to the Connection. This will only happen if the underlying Protocol Stack supports access to soft errors; however, even if the underlying stack supports it, there
is no guarantee that a soft error will be signaled.¶
Connection -> SoftError<>¶
This event notifies the application when at least one of the paths underlying a Connection has changed. Changes occur on a single path when the PMTU changes as well as when multiple paths are used and paths are added or removed, the set of local endpoints changes, or a handover has been performed.¶
Connection -> PathChange<>¶
Data is sent and received as Messages, which allows the application to communicate the boundaries of the data being transferred.¶
Each Message has an optional Message Context, which allows adding Message Properties, identify Send events related to a specific Message or to inspect meta-data related to the Message sent. Framers can be used to extend or modify the Message data with additional information that can be processed at the receiver to detect message boundaries.¶
Using the MessageContext object, the application can set and retrieve meta-data of the Message, including Message Properties (see Section 9.1.3) and framing meta-data (see Section 9.1.2.2).
Therefore, a MessageContext object can be passed to the Send action and is returned by each Send and Receive related event.¶
Message Properties can be set and queried using the Message Context:¶
MessageContext.add(property, value) PropertyValue := MessageContext.get(property)¶
These Message Properties can be generic properties or Protocol-specific Properties.¶
For MessageContexts returned by Send events (see Section 9.2.2) and Receive events (see Section 9.3.2), the application can query information about the Local and Remote Endpoint:¶
RemoteEndpoint := MessageContext.GetRemoteEndpoint() LocalEndpoint := MessageContext.GetLocalEndpoint()¶
Although most applications communicate over a network using well-formed Messages, the boundaries and metadata of the Messages are often not directly communicated by the transport protocol itself. For example, HTTP applications send and receive HTTP messages over a byte-stream transport, requiring that the boundaries of HTTP messages be parsed from the stream of bytes.¶
Message Framers allow extending a Connection's Protocol Stack to define how to encapsulate or encode outbound Messages, and how to decapsulate or decode inbound data into Messages. Message Framers allow message boundaries to be preserved when using a Connection object, even when using byte-stream transports. This is designed based on the fact that many of the current application protocols evolved over TCP, which does not provide message boundary preservation, and since many of these protocols require message boundaries to function, each application layer protocol has defined its own framing.¶
To use a Message Framer, the application adds it to its Preconnection object.
Then, the Message Framer can intercept all calls to Send or Receive
on a Connection to add Message semantics, in addition to interacting with
the setup and teardown of the Connection. A Framer can start sending data
before the application sends data if the framing protocol requires a prefix
or handshake (see [RFC9329] for an example of such a framing protocol).¶
Initiate() Send() Receive() Close()
| | ^ |
| | | |
+----v----------v---------+----------v-----+
| Connection |
+----+----------+---------^----------+-----+
| | | |
| +-----------------+ |
| | Messages | |
| +-----------------+ |
| | | |
+----v----------v---------+----------v-----+
| Framer(s) |
+----+----------+---------^----------+-----+
| | | |
| +-----------------+ |
| | Byte-stream | |
| +-----------------+ |
| | | |
+----v----------v---------+----------v-----+
| Transport Protocol Stack |
+------------------------------------------+
Note that while Message Framers add the most value when placed above a protocol that otherwise does not preserve message boundaries, they can also be used with datagram- or message-based protocols. In these cases, they add a transformation to further encode or encapsulate, and can potentially support packing multiple application-layer Messages into individual transport datagrams.¶
The API to implement a Message Framer can vary depending on the implementation; guidance on implementing Message Framers can be found in [I-D.ietf-taps-impl].¶
The Message Framer object can be added to one or more Preconnections to run on top of transport protocols. Multiple Framers can be added to a Preconnection; in this case, the Framers operate as a framing stack, i.e. the last one added runs first when framing outbound Messages, and last when parsing inbound data.¶
The following example adds a basic HTTP Message Framer to a Preconnection:¶
framer := NewHTTPMessageFramer() Preconnection.AddFramer(framer)¶
Since Message Framers pass from Preconnection to Listener or Connection, addition of Framers must happen before any operation that might result in the creation of a Connection.¶
When sending Messages, applications can add Framer-specific
properties to a MessageContext (Section 9.1.1) with the add action.
To avoid naming conflicts, the property
names SHOULD be prefixed with a namespace referencing the
framer implementation or the protocol it implements as described
in Section 4.1.¶
This mechanism can be used, for example, to set the type of a Message for a TLV format. The namespace of values is custom for each unique Message Framer.¶
messageContext := NewMessageContext() messageContext.add(framer, key, value) Connection.Send(messageData, messageContext)¶
When an application receives a MessageContext in a Receive event,
it can also look to see if a value was set by a specific Message Framer.¶
messageContext.get(framer, key) -> value¶
For example, if an HTTP Message Framer is used, the values could correspond to HTTP headers:¶
httpFramer := NewHTTPMessageFramer() ... messageContext := NewMessageContext() messageContext.add(httpFramer, "accept", "text/html")¶
Applications needing to annotate the Messages they send with extra information
(for example, to control how data is scheduled and processed by the transport protocols supporting the
Connection) can include this information in the Message Context passed to the Send action. For other uses of the Message Context, see Section 9.1.1.¶
Message Properties are per-Message, not per-Send if partial Messages
are sent (Section 9.2.3). All data blocks associated with a single Message
share properties specified in the Message Contexts. For example, it would not
make sense to have the beginning of a Message expire, but allow the end of a
Message to still be sent.¶
A MessageContext object contains metadata for the Messages to be sent or received.¶
messageData := "hello" messageContext := NewMessageContext() messageContext.add(parameter, value) Connection.Send(messageData, messageContext)¶
The simpler form of Send, which does not take any MessageContext, is equivalent to passing a default MessageContext without adding any Message Properties.¶
If an application wants to override Message Properties for a specific Message, it can acquire an empty MessageContext object and add all desired Message Properties to that object. It can then reuse the same MessageContext object for sending multiple Messages with the same properties.¶
Properties can be added to a MessageContext object only before the context is used
for sending. Once a MessageContext has been used with a Send action, further modifications
to the MessageContext object do not have any effect on this Send call. Message Properties
that are not added to a MessageContext object before using the context for sending will either
take a specific default value or be configured based on Selection or Connection Properties
of the Connection that is associated with the Send call.
This initialization behavior is defined per Message Property below.¶
The Message Properties could be inconsistent with the properties of the Protocol Stacks
underlying the Connection on which a given Message is sent. For example,
a Protocol Stack must be able to provide ordering if the msgOrdered
property of a Message is enabled. Sending a Message with Message Properties
inconsistent with the Selection Properties of the Connection yields an error.¶
If a Message Property contradicts a Connection Property, and
if this per-Message behavior can be supported, it overrides the Connection
Property for the specific Message. For example, if
reliability is set to Require and a protocol
with configurable per-Message reliability is used, setting
msgReliable to false for a particular Message will
allow this Message to be sent without any reliability guarantees. Changing
the msgReliable Message Property is only possible for
Connections that were established enabling the Selection Property
perMsgReliability. If the contradicting Message Property
cannot be supported by the Connection (such as requiring reliability
on a Connection that uses an unreliable protocol), the Send action
will result in a SendError event.¶
The following Message Properties are supported:¶
The Lifetime specifies how long a particular Message can wait in the Transport Services system before it is sent to the Remote Endpoint. After this time, it is irrelevant and no longer needs to be (re-)transmitted. This is a hint to the Transport Services system -- it is not guaranteed that a Message will not be sent when its Lifetime has expired.¶
Setting a Message's Lifetime to infinite indicates that the application does
not wish to apply a time constraint on the transmission of the Message, but it does not express a need for
reliable delivery; reliability is adjustable per Message via the perMsgReliability
property (see Section 9.1.3.7). The type and units of Lifetime are implementation-specific.¶
This property specifies the priority of a Message, relative to other Messages sent over the same Connection. A numerically lower value represents a higher priority.¶
A Message with Priority 2 will yield to a Message with Priority 1, which will yield to a Message with Priority 0, and so on. Priorities can be used as a sender-side scheduling construct only, or be used to specify priorities on the wire for Protocol Stacks supporting prioritization.¶
Note that this property is not a per-Message override of connPriority
- see Section 8.1.2. The priority properties might interact, but can be used
independently and be realized by different mechanisms; see Section 9.2.6.¶
msgOrdered¶
Boolean¶
the queried Boolean value of the Selection Property preserveOrder (Section 6.2.4)¶
The order in which Messages were submitted for transmission via the Send action will be preserved on delivery via Receive events for all Messages on a Connection that have this Message Property set to true.¶
If false, the Message is delivered to the receiving application without preserving the ordering.
This property is used for protocols that support preservation of data ordering,
see Section 6.2.4, but allow out-of-order delivery for certain Messages, e.g., by multiplexing independent Messages onto
different streams.¶
If it is not configured by the application before sending, this property's default value
will be based on the Selection Property preserveOrder of the Connection
associated with the Send action.¶
If true, safelyReplayable specifies that a Message is safe to send to the Remote Endpoint
more than once for a single Send action. It marks the data as safe for
certain 0-RTT establishment techniques, where retransmission of the 0-RTT data
could cause the remote application to receive the Message multiple times.¶
For protocols that do not protect against duplicated Messages,
e.g., UDP, all Messages need to be marked as "safely replayable" by enabling this property.
To enable protocol selection to choose such a protocol,
safelyReplayable needs to be added to the TransportProperties passed to the
Preconnection. If such a protocol was chosen, disabling safelyReplayable on
individual Messages MUST result in a SendError.¶
If true, this indicates a Message is the last that
the application will send on a Connection. This allows underlying protocols
to indicate to the Remote Endpoint that the Connection has been effectively
closed in the sending direction. For example, TCP-based Connections can
send a FIN once a Message marked as Final has been completely sent,
indicated by marking endOfMessage. Protocols that do not support signalling
the end of a Connection in a given direction will ignore this property.¶
A Final Message must always be sorted to the end of a list of Messages.
The Final property overrides Priority and any other property that would re-order
Messages. If another Message is sent after a Message marked as Final has already
been sent on a Connection, the Send action for the new Message will cause a SendError event.¶
If this property is an Integer, it specifies the minimum length of the section of a sent Message,
starting from byte 0, that the application requires to be delivered without
corruption due to lower layer errors. It is used to specify options for simple
integrity protection via checksums. A value of 0 means that no checksum
needs to be calculated, and the enumerated value Full Coverage means
that the entire Message needs to be protected by a checksum. Only Full Coverage is
guaranteed, any other requests are advisory, which may result in Full Coverage being applied.¶
msgReliable¶
Boolean¶
the queried Boolean value of the Selection Property reliability (Section 6.2.1)¶
When true, this property specifies that a Message should be sent in such a way
that the transport protocol ensures all data is received by the Remote Endpoint.
Changing the msgReliable property on Messages
is only possible for Connections that were established enabling the Selection Property perMsgReliability.
When this is not the case, changing msgReliable will generate an error.¶
Disabling this property indicates that the Transport Services system could disable retransmissions or other reliability mechanisms for this particular Message, but such disabling is not guaranteed.¶
If it is not configured by the application before sending, this property's default value
will be based on the Selection Property reliability of the Connection
associated with the Send action.¶
msgCapacityProfile¶
Enumeration¶
inherited from the Connection Property connCapacityProfile (Section 8.1.6)¶
This enumerated property specifies the application's preferred tradeoffs for
sending this Message; it is a per-Message override of the connCapacityProfile
Connection Property (see Section 8.1.6).
If it is not configured by the application before sending, this property's default value
will be based on the Connection Property connCapacityProfile of the Connection
associated with the Send action.¶
This property specifies that a Message should be sent and received without network-layer fragmentation, if possible. It can be used to avoid network layer fragmentation when transport segmentation is preferred.¶
This only takes effect when the transport uses a network layer that supports this functionality.
When it does take effect, setting this property to
true will cause the sender to avoid network-layer source fragmentation.
When using IPv4, this will result in the Don't Fragment bit being set in the IP header.¶
Attempts to send a Message with this property that result in a size greater than the
transport's current estimate of its maximum packet size (singularTransmissionMsgMaxLen)
can result in transport segmentation when permitted, or in a SendError.¶
Note: noSegmentation is used when it is desired to only send a Message within a single network packet.¶
When set to true, this property requests the transport layer
to not provide segmentation of Messages larger than the
maximum size permitted by the network layer, and also
to avoid network-layer source fragmentation of Messages.
When running over IPv4, setting this property to
true will result in a sending endpoint setting the
Don't Fragment bit in the IPv4 header of packets generated by the
transport layer.¶
An
attempt to send a Message that results in a size greater than the
transport's current estimate of its maximum packet size (singularTransmissionMsgMaxLen)
will result in a SendError.
This only takes effect when the transport and network layer
support this functionality.¶
Once a Connection has been established, it can be used for sending Messages.
By default, Send enqueues a complete Message,
and takes optional per-Message properties (see Section 9.2.1). All Send actions
are asynchronous, and deliver events (see Section 9.2.2). Sending partial
Messages for streaming large data is also supported (see Section 9.2.3).¶
Messages are sent on a Connection using the Send action:¶
Connection.Send(messageData, messageContext?, endOfMessage?)¶
where messageData is the data object to send, and messageContext allows
adding Message Properties, identifying Send events related to a specific
Message or inspecting meta-data related to the Message sent (see Section 9.1.1).¶
The optional endOfMessage parameter supports partial sending and is described in Section 9.2.3.¶
The most basic form of sending on a Connection involves enqueuing a single Data block as a complete Message with default Message Properties.¶
messageData := "hello" Connection.Send(messageData)¶
The interpretation of a Message to be sent is dependent on the implementation, and on the constraints on the Protocol Stacks implied by the Connection’s transport properties. For example, a Message could be the payload of a single datagram for a UDP Connection; or an HTTP Request for an HTTP Connection.¶
Some transport protocols can deliver arbitrarily sized Messages, but other
protocols constrain the maximum Message size. Applications can query the
Connection Property sendMsgMaxLen (Section 8.1.11.5) to determine the maximum size
allowed for a single Message. If a Message is too large to fit in the Maximum Message
Size for the Connection, the Send will fail with a SendError event (Section 9.2.2.3). For
example, it is invalid to send a Message over a UDP connection that is larger than
the available datagram sending size.¶
Like all actions in Transport Services API, the Send action is asynchronous. There are
several events that can be delivered in response to sending a Message.
Exactly one event (Sent, Expired, or SendError) will be delivered in response
to each call to Send.¶
Note that if partial Send calls are used (Section 9.2.3), there will still be exactly
one Send event delivered for each call to Send. For example, if a Message
expired while two requests to Send data for that Message are outstanding,
there will be two Expired events delivered.¶
The Transport Services API should allow the application to correlate which Send action resulted
in a particular Send event. The manner in which this correlation is indicated
is implementation-specific.¶
Connection -> Sent<messageContext>¶
The Sent event occurs when a previous Send call has completed, i.e., when
the data derived from the Message has been passed down or through the
underlying Protocol Stack and is no longer the responsibility of
the Transport Services API. The exact disposition of the Message (i.e.,
whether it has actually been transmitted, moved into a buffer on the network
interface, moved into a kernel buffer, and so on) when the Sent event occurs
is implementation-specific. The Sent event contains a reference to the Message
Context of the Message to which it applies.¶
Sent events allow an application to obtain an understanding of the amount
of buffering it creates. That is, if an application calls the Send action multiple
times without waiting for a Sent event, it has created more buffer inside the
Transport Services system than an application that always waits for the Sent event before
calling the next Send action.¶
Connection -> Expired<messageContext>¶
The Expired event occurs when a previous Send action expired before completion;
i.e. when the Message was not sent before its Lifetime (see Section 9.1.3.1)
expired. This is separate from SendError, as it is an expected behavior for
partially reliable transports. The Expired event contains a reference to the
Message Context of the Message to which it applies.¶
Connection -> SendError<messageContext, reason?>¶
A SendError occurs when a Message was not sent due to an error condition:
an attempt to send a Message that is too large for the system and
Protocol Stack to handle, some failure of the underlying Protocol Stack, or a
set of Message Properties not consistent with the Connection's transport
properties. The SendError contains a reference to the Message Context of the
Message to which it applies.¶
It is not always possible for an application to send all data associated with
a Message in a single Send action. The Message data might be too large for
the application to hold in memory at one time, or the length of the Message
might be unknown or unbounded.¶
Partial Message sending is supported by passing an endOfMessage Boolean
parameter to the Send action. This value is always true by default, and
the simpler forms of Send are equivalent to passing true for endOfMessage.¶
The following example sends a Message in two separate calls to Send.¶
messageContext := NewMessageContext() messageContext.add(parameter, value) messageData := "hel" endOfMessage := false Connection.Send(messageData, messageContext, endOfMessage) messageData := "lo" endOfMessage := true Connection.Send(messageData, messageContext, endOfMessage)¶
All data sent with the same MessageContext object will be treated as belonging to the same Message, and will constitute an in-order series until the endOfMessage is marked.¶
To reduce the overhead of sending multiple small Messages on a Connection, the
application could batch several Send actions together. This provides a hint to
the system that the sending of these Messages ought to be coalesced when possible,
and that sending any of the batched Messages can be delayed until the last Message
in the batch is enqueued.¶
The semantics for starting and ending a batch can be implementation-specific, but need
to allow multiple Send actions to be enqueued.¶
Connection.StartBatch() Connection.Send(messageData) Connection.Send(messageData) Connection.EndBatch()¶
For application-layer protocols where the Connection initiator also sends the
first Message, the InitiateWithSend action combines Connection initiation with
a first Message sent:¶
Connection := Preconnection.InitiateWithSend(messageData,
messageContext?,
timeout?)
¶
Whenever possible, a MessageContext should be provided to declare the Message passed to InitiateWithSend
as "safely replayable" using the safelyReplayable property. This allows the Transport Services system to make use of 0-RTT establishment in case this is supported
by the available Protocol Stacks. When the selected stack(s) do not support transmitting data upon connection
establishment, InitiateWithSend is identical to Initiate followed by Send.¶
Neither partial sends nor send batching are supported by InitiateWithSend.¶
The events that are sent after InitiateWithSend are equivalent to those
that would be sent by an invocation of Initiate followed immediately by an
invocation of Send, with the caveat that a send failure that occurs because
the Connection could not be established will not result in a
SendError separate from the EstablishmentError signaling the failure of Connection
establishment.¶
The Transport Services API provides two properties to allow a sender
to signal the relative priority of data transmission: msgPriority
Section 9.1.3.2 and connPriority Section 8.1.2.
These properties are designed to allow the expression
and implementation of a wide variety of approaches to transmission priority in
the transport and application layer, including those which do not appear on
the wire (affecting only sender-side transmission scheduling) as well as those
that do (e.g. [RFC9218].
A Transport Services system gives no guarantees about how its expression of
relative priorities will be realized.¶
The Transport Services API does order connPriority over
msgPriority. In the absence of other externalities
(e.g., transport-layer flow control), a priority 1 Message on a priority 0
Connection will be sent before a priority 0 Message on a priority 1
Connection in the same group.¶
Once a Connection is established, it can be used for receiving data (unless the
direction property is set to unidirectional send). As with
sending, the data is received in Messages. Receiving is an asynchronous
operation, in which each call to Receive enqueues a request to receive new
data from the Connection. Once data has been received, or an error is encountered,
an event will be delivered to complete any pending Receive requests (see Section 9.3.2).
If Messages arrive at the Transport Services system before Receive requests are issued,
ensuing Receive requests will first operate on these Messages before awaiting any further Messages.¶
Receive takes two parameters to specify the length of data that an application
is willing to receive, both of which are optional and have default values if not
specified.¶
Connection.Receive(minIncompleteLength?, maxLength?)¶
By default, Receive will try to deliver complete Messages in a single event (Section 9.3.2.1).¶
The application can set a minIncompleteLength value to indicate the smallest partial
Message data size in bytes to be delivered in response to this Receive. By default,
this value is infinite, which means that only complete Messages should be delivered (see Section 9.3.2.2
and Section 9.1.2 for more information on how this is accomplished).
If this value is set to some smaller value, the associated receive event will be triggered
only when at least that many bytes are available, or the Message is complete with fewer
bytes, or the system needs to free up memory. Applications SHOULD always
check the length of the data delivered to the receive event and not assume
it will be as long as minIncompleteLength in the case of shorter complete Messages
or memory issues.¶
The maxLength argument indicates the maximum size of a Message in bytes
that the application is currently prepared to receive. The default
value for maxLength is infinite. If an incoming Message is larger than the
minimum of this size and the maximum Message size on receive for
the Connection's Protocol Stack, it will be delivered via ReceivedPartial
events (Section 9.3.2.2).¶
Note that maxLength does not guarantee that the application will receive that many
bytes if they are available; the Transport Services API could return ReceivedPartial events with less
data than maxLength according to implementation constraints. Note also that maxLength
and minIncompleteLength are intended only to manage buffering, and are not interpreted
as a receiver preference for Message reordering.¶
Each call to Receive will be paired with a single Receive event. This allows an application
to provide backpressure to the transport stack when it is temporarily not ready to receive Messages.
For example, an application that will later be able to handle multiple receive events at the same time
can make multiple calls to Receive without waiting for, or processing, any receive events. An application
that is temporarily unable to process received events for a connection could refrain from calling Receive
or delay calling it. This would lead to a build-up of unread data, which, in turn, could result in
backpressure to the sender via a transport protocol's flow control.¶
The Transport Services API should allow the application to correlate which call to Receive resulted
in a particular Receive event. The manner in which this correlation is indicated
is implementation-specific.¶
Connection -> Received<messageData, messageContext>¶
A Received event indicates the delivery of a complete Message.
It contains two objects, the received bytes as messageData, and the metadata and properties of the received Message as messageContext.¶
The messageData value provides access to the bytes that were received for this Message, along with the length of the byte array.
The messageContext value is provided to enable retrieving metadata about the Message and referring to the Message. The MessageContext object is described in Section 9.1.1.¶
See Section 9.1.2 for handling Message framing in situations where the Protocol Stack only provides a byte-stream transport.¶
Connection -> ReceivedPartial<messageData, messageContext,
endOfMessage>
¶
If a complete Message cannot be delivered in one event, one part of the Message
can be delivered with a ReceivedPartial event. To continue to receive more
of the same Message, the application must invoke Receive again.¶
Multiple invocations of ReceivedPartial deliver data for the same Message by
passing the same MessageContext, until the endOfMessage flag is delivered or a
ReceiveError occurs. All partial blocks of a single Message are delivered in
order without gaps. This event does not support delivering non-contiguous partial
Messages. If, for example, Message A is divided into three pieces (A1, A2, A3) and
Message B is divided into three pieces (B1, B2, B3), and preserveOrder is not Required,
the ReceivedPartial could deliver them in a sequence like this: A1, B1, B2, A2, A3, B3,
because the MessageContext allows the application to identify the pieces as belonging
to Message A and B, respectively. However, a sequence like: A1, A3 will never occur.¶
If the minIncompleteLength in the Receive request was set to be infinite (indicating
a request to receive only complete Messages), the ReceivedPartial event could still be
delivered if one of the following conditions is true:¶
the underlying Protocol Stack supports message boundary preservation, and the size of the Message is larger than the buffers available for a single Message;¶
the underlying Protocol Stack does not support message boundary preservation, and the Message Framer (see Section 9.1.2) cannot determine the end of the Message using the buffer space it has available; or¶
the underlying Protocol Stack does not support message boundary preservation, and no Message Framer was supplied by the application¶
Note that in the absence of message boundary preservation or a Message Framer, all bytes received on the Connection will be represented as one large Message of indeterminate length.¶
In the following example, an application only wants to receive up to 1000 bytes
at a time from a Connection. If a 1500-byte Message arrives, it would receive
the Message in two separate ReceivedPartial events.¶
Connection.Receive(1, 1000)
// Receive first 1000 bytes, message is incomplete
Connection -> ReceivedPartial<messageData(1000 bytes),
messageContext, false>
Connection.Receive(1, 1000)
// Receive last 500 bytes, message is now complete
Connection -> ReceivedPartial<messageData(500 bytes),
messageContext, true>
¶
Connection -> ReceiveError<messageContext, reason?>¶
A ReceiveError occurs when data is received by the underlying Protocol Stack
that cannot be fully retrieved or parsed, and when it is useful for the application
to be notified of such errors. For example, a ReceiveError can
indicate that a Message (identified via the messageContext value)
that was being partially received previously, but had not
completed, encountered an error and will not be completed. This can be useful
for an application, which might wish to use this error as a hint to remove
previously received Message parts from memory. As another example,
if an incoming Message does not fulfill the recvChecksumLen property
(see Section 8.1.1),
an application can use this error as a hint to inform the peer application
to adjust the msgChecksumLen property (see Section 9.1.3.6).¶
In contrast, internal protocol reception errors (e.g., loss causing retransmissions
in TCP) are not signalled by this event. Conditions that irrevocably lead to
the termination of the Connection are signaled using ConnectionError
(see Section 10).¶
Each Message Context could contain metadata from protocols in the Protocol Stack; which metadata is available is Protocol Stack dependent. These are exposed through additional read-only Message Properties that can be queried from the MessageContext object (see Section 9.1.1) passed by the receive event. The following metadata values are supported:¶
When available, Message metadata carries the value of the Explicit Congestion Notification (ECN) field. This information can be used for logging and debugging, and for building applications that need access to information about the transport internals for their own operation. This property is specific to UDP and UDP-Lite because these protocols do not implement congestion control, and hence expose this functionality to the application (see [RFC8293], following the guidance in [RFC8085])¶
In some cases it can be valuable to know whether data was read as part of early data transfer (before Connection establishment has finished). This is useful if applications need to treat early data separately, e.g., if early data has different security properties than data sent after connection establishment. In the case of TLS 1.3, client early data can be replayed maliciously (see [RFC8446]). Thus, receivers might wish to perform additional checks for early data to ensure it is safely replayable. If TLS 1.3 is available and the recipient Message was sent as part of early data, the corresponding metadata carries a flag indicating as such. If early data is enabled, applications should check this metadata field for Messages received during Connection establishment and respond accordingly.¶
The Message Context can indicate whether or not this Message is
the Final Message on a Connection. For any Message that is marked as Final,
the application can assume that there will be no more Messages received on the
Connection once the Message has been completely delivered. This corresponds
to the final property that can be marked on a sent Message, see Section 9.1.3.5.¶
Some transport protocols and peers do not support signaling of the final property.
Applications therefore SHOULD NOT rely on receiving a Message marked Final to know
that the sending endpoint is done sending on a Connection.¶
Any calls to Receive once the Final Message has been delivered will result in errors.¶
A Connection can be terminated i) by the Local Endpoint (i.e., the application calls the Close, CloseGroup, Abort or AbortGroup action), ii) by the Remote Endpoint (i.e., the remote application calls the Close, CloseGroup, Abort or AbortGroup action), or iii) because of an error (e.g., a timeout). A local call of the Close action will
cause the Connection to either send a Closed event or a ConnectionError event, and a local call of
the CloseGroup action will cause all of the Connections in the group to either send a Closed event
or a ConnectionError event. A local call of the Abort action will cause the Connection to send
a ConnectionError event, indicating local Abort as a reason, and a local call of the AbortGroup action
will cause all of the Connections in the group to send a ConnectionError event, indicating local Abort
as a reason.¶
Remote action calls map to events similar to local calls (e.g., a remote Close causes the
Connection to either send a Closed event or a ConnectionError event), but, different from local action calls,
it is not guaranteed that such events will indeed be invoked. When an application needs to free resources
associated with a Connection, it ought not to therefore rely on the invocation of such events due to
termination calls from the Remote Endpoint, but instead use the local termination actions.¶
Close terminates a Connection after satisfying all the requirements that were
specified regarding the delivery of Messages that the application has already
given to the Transport Services system. Upon successfully satisfying all these
requirements, the Connection will send the Closed event. For example, if reliable delivery was requested
for a Message handed over before calling Close, the Closed event will signify
that this Message has indeed been delivered. This action does not affect any other Connection
in the same Connection Group.¶
An application MUST NOT assume that it can receive any further data on a Connection
for which it has called Close, even if such data is already in flight.¶
Connection.Close()¶
The Closed event informs the application that a Close action has successfully
completed, or that the Remote Endpoint has closed the Connection.
There is no guarantee that a remote Close will be signaled.¶
Connection -> Closed<>¶
Abort terminates a Connection without delivering any remaining Messages. This action does
not affect any other Connection that is entangled with this one in a Connection Group.
When the Abort action has finished, the Connection will send a ConnectionError event,
indicating local Abort as a reason.¶
Connection.Abort()¶
CloseGroup gracefully terminates a Connection and any other Connections in the
same Connection Group. For example, all of the Connections in a
group might be streams of a single session for a multistreaming protocol; closing the entire
group will close the underlying session. See also Section 7.4. All Connections in the group
will send a Closed event when the CloseGroup action was successful.
As with Close, any Messages
remaining to be processed on a Connection will be handled prior to closing.¶
Connection.CloseGroup()¶
AbortGroup terminates a Connection and any other Connections that are
in the same Connection Group without delivering any remaining Messages.
When the AbortGroup action has finished, all Connections in the group will
send a ConnectionError event, indicating local Abort as a reason.¶
Connection.AbortGroup()¶
A ConnectionError informs the application that: 1) data could not be delivered to the
peer after a timeout,
or 2) the Connection has been aborted (e.g., because the peer has called Abort).
There is no guarantee that an Abort from the peer will be signaled.¶
Connection -> ConnectionError<reason?>¶
This Transport Services API is designed to be independent of an implementation's concurrency model. The details of how exactly actions are handled, and how events are dispatched, are implementation dependent.¶
Some transitions of Connection states are associated with events:¶
Ready<> occurs when a Connection created with Initiate or
InitiateWithSend transitions to Established state.¶
ConnectionReceived<> occurs when a Connection created with Listen
transitions to Established state.¶
RendezvousDone<> occurs when a Connection created with Rendezvous
transitions to Established state.¶
Closed<> occurs when a Connection transitions to Closed state without error.¶
EstablishmentError<> occurs when a Connection created with Initiate transitions
from Establishing state to Closed state due to an error.¶
ConnectionError<> occurs when a Connection transitions to Closed state due to
an error in all other circumstances.¶
The following diagram shows the possible states of a Connection and the events that occur upon a transition from one state to another.¶
(*) (**)
Establishing -----> Established -----> Closing ------> Closed
| ^
| |
+---------------------------------------------------+
EstablishmentError<>
(*) Ready<>, ConnectionReceived<>, RendezvousDone<>
(**) Closed<>, ConnectionError<>
The Transport Services API provides the following guarantees about the ordering of operations:¶
Sent<> events will occur on a Connection in the order in which the Messages
were sent (i.e., delivered to the kernel or to the network interface,
depending on implementation).¶
Received<> will never occur on a Connection before it is Established; i.e.
before a Ready<> event on that Connection, or a ConnectionReceived<> or
RendezvousDone<> containing that Connection.¶
No events will occur on a Connection after it is closed; i.e., after a
Closed<> event, an EstablishmentError<> or ConnectionError<> will not occur on that Connection. To
ensure this ordering, Closed<> will not occur on a Connection while other
events on the Connection are still locally outstanding (i.e., known to the
Transport Services API and waiting to be dealt with by the application).¶
This document has no actions for IANA. Later versions of this document might create IANA registries for generic transport property names and transport property namespaces (see Section 4.1).¶
This document describes a generic API for interacting with a Transport Services system. Part of this API includes configuration details for transport security protocols, as discussed in Section 6.3. It does not recommend use (or disuse) of specific algorithms or protocols. Any API-compatible transport security protocol ought to work in a Transport Services system. Security considerations for these protocols are discussed in the respective specifications.¶
The described API is used to exchange information between an application and the Transport Services system. While it is not necessarily expected that both systems are implemented by the same authority, it is expected that the Transport Services Implementation is either provided as a library that is selected by the application from a trusted party, or that it is part of the operating system that the application also relies on for other tasks.¶
In either case, the Transport Services API is an internal interface that is used to exchange information locally between two systems. However, as the Transport Services system is responsible for network communication, it is in the position to potentially share any information provided by the application with the network or another communication peer. Most of the information provided over the Transport Services API are useful to configure and select protocols and paths and are not necessarily privacy-sensitive. Still, some information could be privacy sensitive because it might reveal usage characteristics and habits of the user of an application.¶
Of course any communication over a network reveals usage characteristics, because all packets, as well as their timing and size, are part of the network-visible wire image [RFC8546]. However, the selection of a protocol and its configuration also impacts which information is visible, potentially in clear text, and which other entities can access it. How Transport Services systems ought to choose protocols depending on the security properties required is out of scope of this specification, as it is limited to transport protocols. The choice of a security protocol can be informed by the survey provided in [RFC8922].¶
In most cases, information provided for protocol and path selection does not directly translate to information that can be observed by network devices on the path. However, there might be specific configuration information that is intended for path exposure, e.g., a DiffServ codepoint setting, that is either provided directly by the application or indirectly configured for a traffic profile.¶
Applications should be aware that a single communication attempt can lead to more than one connection establishment procedure. This is the case, for example, when the Transport Services system also executes name resolution, when support mechanisms such as TURN or ICE are used to establish connectivity, if protocols or paths are raced, or if a path fails and fallback or re-establishment is supported in the Transport Services system. Applications should take special care when using 0-RTT session resumption (see Section 6.2.5), as early data sent across multiple paths during connection establishment could reveal information that can be used to correlate endpoints on these paths.¶
Applications should also take care to not assume that all data received using the Transport Services API is always complete or well-formed. Specifically, Messages that are received partially Section 9.3.2.2 could be a source of truncation attacks if applications do not distinguish between partial Messages and complete Messages.¶
The Transport Services API explicitly does not require the application to resolve names, though there is a tradeoff between early and late binding of addresses to names. Early binding allows the Transport Services Implementation to reduce Connection setup latency, at the cost of potentially limited scope for alternate path discovery during Connection establishment, as well as potential additional information leakage about application interest when used with a resolution method (such as DNS without TLS) which does not protect query confidentiality.¶
These communication activities are not different from what is used today. However, the goal of a Transport Services system is to support such mechanisms as a generic service within the transport layer. This enables applications to more dynamically benefit from innovations and new protocols in the transport, although it reduces transparency of the underlying communication actions to the application itself. The Transport Services API is designed such that protocol and path selection can be limited to a small and controlled set if the application requires this or to implement a security policy. can be limited to a small and controlled set if required by the application to perform a function or to provide security. Further, introspection on the properties of Connection objects allows an application to determine which protocol(s) and path(s) are in use. A Transport Services system SHOULD provide a facility logging the communication events of each Connection.¶
This work has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreements No. 644334 (NEAT) and No. 688421 (MAMI).¶
This work has been supported by Leibniz Prize project funds of DFG - German Research Foundation: Gottfried Wilhelm Leibniz-Preis 2011 (FKZ FE 570/4-1).¶
This work has been supported by the UK Engineering and Physical Sciences Research Council under grant EP/R04144X/1.¶
This work has been supported by the Research Council of Norway under its "Toppforsk" programme through the "OCARINA" project.¶
Thanks to Stuart Cheshire, Josh Graessley, David Schinazi, and Eric Kinnear for their implementation and design efforts, including Happy Eyeballs, that heavily influenced this work. Thanks to Laurent Chuat and Jason Lee for initial work on the Post Sockets interface, from which this work has evolved. Thanks to Maximilian Franke for asking good questions based on implementation experience and for contributing text, e.g., on multicast.¶
The way the concepts from this abstract API map into concrete APIs in a given language on a given platform largely depends on the features and norms of the language and the platform. Actions could be implemented as functions or method calls, for instance, and events could be implemented via event queues, handler functions or classes, communicating sequential processes, or other asynchronous calling conventions.¶
The basic types mentioned in Section 1.1 typically have natural correspondences in practical programming languages, perhaps constrained by implementation-specific limitations. For example:¶
An Integer can typically be represented in C by an int or long, subject
to the underlying platform's ranges for each.¶
In C, a Tuple may be represented as a struct with one member for each of
the value types in the ordered grouping. In Python, by contrast, a Tuple may
be represented as a tuple, a sequence of dynamically-typed
elements.¶
A Set may be represented as a std::set in C++ or as a set in
Python. In C, it may be represented as an array or as a higher-level data
structure with appropriate accessors defined.¶
The objects described in Section 1.1 can similarly be represented in different ways depending on which programming language is used. Objects like Preconnections, Connections, and Listeners can be long-lived, and benefit from using object-oriented constructs. Note that in C, these objects may need to provide a way to release or free their underlying memory when the application is done using them. For example, since a Preconnection can be used to initiate multiple Connections, it is the responsibility of the application to clean up the Preconnection memory if necessary.¶
This specification treats events and errors similarly. Errors, just as any other events, may occur asynchronously in network applications. However, implementations of this API may report errors synchronously, according to the error handling idioms of the implementation platform, where they can be immediately detected, such as by generating an exception when attempting to initiate a Connection with inconsistent Transport Properties. An error can provide an optional reason to the application with further details about why the error occurred.¶
Time duration types are implementation-specific.
For instance, it could be a number of seconds, number of milliseconds, or a struct timeval in C or a user-defined Duration class in C++.¶
TransportProperties will frequently need to set
Selection Properties of type Preference, therefore implementations can provide special actions
for adding each preference level i.e, TransportProperties.Set(some_property, avoid)
is equivalent to TransportProperties.Avoid(some_property)`:¶
TransportProperties.Require(property) TransportProperties.Prefer(property) TransportProperties.NoPreference(property) TransportProperties.Avoid(property) TransportProperties.Prohibit(property)¶
To ease the use of the Transport Services API, implementations can provide a mechanism to create Transport Property objects (see Section 6.2) that are preconfigured with frequently used sets of properties; the following are in common use in current applications:¶
This profile provides reliable, in-order transport service with congestion control. TCP is an example of a protocol that provides this service. It should consist of the following properties:¶
| Property | Value |
|---|---|
| reliability | require |
| preserveOrder | require |
| congestionControl | require |
| preserveMsgBoundaries | no preference |
This profile provides message-preserving, reliable, in-order transport service with congestion control. SCTP is an example of a protocol that provides this service. It should consist of the following properties:¶
| Property | Value |
|---|---|
| reliability | require |
| preserveOrder | require |
| congestionControl | require |
| preserveMsgBoundaries | require |
This profile provides a datagram transport service without any reliability guarantee. An example of a protocol that provides this service is UDP. It consists of the following properties:¶
| Property | Value |
|---|---|
| reliability | avoid |
| preserveOrder | avoid |
| congestionControl | no preference |
| preserveMsgBoundaries | require |
| safelyReplayable | true |
Applications that choose this Transport Property Profile would avoid the additional latency that could be introduced by retransmission or reordering in a transport protocol.¶
Applications that choose this Transport Property Profile to reduce latency should also consider setting an appropriate capacity profile Property, see Section 8.1.6 and might benefit from controlling checksum coverage, see Section 6.2.7 and Section 6.2.8.¶
[RFC8923] identifies a minimal set of transport services that end systems should offer. These services make all non-security-related transport features of TCP, MPTCP, UDP, UDP-Lite, SCTP and LEDBAT available that 1) require interaction with the application, and 2) do not get in the way of a possible implementation over TCP (or, with limitations, UDP). The following text explains how this minimal set is reflected in the present API. For brevity, it is based on the list in Section 4.1 of [RFC8923], updated according to the discussion in Section 5 of [RFC8923]. The present API covers all elements of this section. This list is a subset of the transport features in Appendix A of [RFC8923], which refers to the primitives in "pass 2" (Section 4) of [RFC8303] for further details on the implementation with TCP, MPTCP, UDP, UDP-Lite, SCTP and LEDBAT. This facilitates finding the specifications for implementing the services listed below with these protocols.¶
Connect:
Initiate action (Section 7.1).¶
Listen:
Listen action (Section 7.2).¶
Specify number of attempts and/or timeout for the first establishment Message:
timeout parameter of Initiate (Section 7.1) or InitiateWithSend action (Section 9.2.5).¶
Disable MPTCP:
multipath property (Section 6.2.14).¶
Hand over a Message to reliably transfer (possibly multiple times) before connection establishment:
InitiateWithSend action (Section 9.2.5).¶
Change timeout for aborting connection (using retransmit limit or time value):
connTimeout property, using a time value (Section 8.1.3).¶
Timeout event when data could not be delivered for too long:
ConnectionError event (Section 10).¶
Suggest timeout to the peer: See "TCP-specific Properties: User Timeout Option (UTO)" (Section 8.2).¶
Notification of ICMP error message arrival:
softErrorNotify (Section 6.2.17) and SoftError event (Section 8.3.1).¶
Choose a scheduler to operate between streams of an association:
connScheduler property (Section 8.1.5).¶
Configure priority or weight for a scheduler:
connPriority property (Section 8.1.2).¶
"Specify checksum coverage used by the sender" and "Disable checksum when sending":
msgChecksumLen property (Section 9.1.3.6) and fullChecksumSend property (Section 6.2.7).¶
"Specify minimum checksum coverage required by receiver" and "Disable checksum requirement when receiving":
recvChecksumLen property (Section 8.1.1) and fullChecksumRecv property (Section 6.2.8).¶
"Specify DF field":
noFragmentation property (Section 9.1.3.9).¶
Get max. transport-message size that may be sent using a non-fragmented IP packet from the configured interface:
singularTransmissionMsgMaxLen property (Section 8.1.11.4).¶
Get max. transport-message size that may be received from the configured interface:
recvMsgMaxLen property (Section 8.1.11.6).¶
Obtain ECN field: This is a read-only Message Property of the MessageContext object (see "UDP(-Lite)-specific Property: ECN" Section 9.3.3.1).¶
"Specify DSCP field", "Disable Nagle algorithm", "Enable and configure a Low Extra Delay Background Transfer":
as suggested in Section 5.5 of [RFC8923], these transport features are collectively offered via the connCapacityProfile property (Section 8.1.6). Per-Message control ("Request not to bundle messages") is offered via the msgCapacityProfile property (Section 9.1.3.8).¶
Close after reliably delivering all remaining data, causing an event informing the application on the other side:
this is offered by the Close action with slightly changed semantics in line with the discussion in Section 5.2 of [RFC8923] (Section 10).¶
"Abort without delivering remaining data, causing an event informing the application on the other side" and "Abort without delivering remaining data, not causing an event informing the application on the other side":
this is offered by the Abort action without promising that this is signaled to the other side. If it is, a ConnectionError event will be invoked at the peer (Section 10).¶
"Reliably transfer data, with congestion control", "Reliably transfer a message, with congestion control" and "Unreliably transfer a message":
data is transferred via the Send action (Section 9.2). Reliability is controlled via the reliability (Section 6.2.1) property and the msgReliable Message Property (Section 9.1.3.7). Transmitting data as a Message or without delimiters is controlled via Message Framers (Section 9.1.2). The choice of congestion control is provided via the congestionControl property (Section 6.2.9).¶
Configurable Message Reliability:
the msgLifetime Message Property implements a time-based way to configure message reliability (Section 9.1.3.1).¶
"Ordered message delivery (potentially slower than unordered)" and "Unordered message delivery (potentially faster than ordered)":
these two transport features are controlled via the Message Property msgOrdered (Section 9.1.3.3).¶
Request not to delay the acknowledgment (SACK) of a message:
should the protocol support it, this is one of the transport features the Transport Services system can apply when an application uses the connCapacityProfile Property (Section 8.1.6) or the msgCapacityProfile Message Property (Section 9.1.3.8) with value Low Latency/Interactive.¶
Receive data (with no message delimiting):
Receive action (Section 9.3.1) and Received event (Section 9.3.2.1).¶
Receive a message:
Receive action (Section 9.3.1) and Received event (Section 9.3.2.1), using Message Framers (Section 9.1.2).¶
Information about partial message arrival:
Receive action (Section 9.3.1) and ReceivedPartial event (Section 9.3.2.2).¶
Notification of send failures:
Expired event (Section 9.2.2.2) and SendError event (Section 9.2.2.3).¶
Notification that the stack has no more user data to send:
applications can obtain this information via the Sent event (Section 9.2.2.1).¶
Notification to a receiver that a partial message delivery has been aborted:
ReceiveError event (Section 9.3.2.3).¶
Notification of Excessive Retransmissions (early warning below abortion threshold):
SoftError event (Section 8.3.1).¶