| Internet-Draft | Multi-Point BFD over P2MP MPLS LSP | February 2022 |
| Mirsky, et al. | Expires 14 August 2022 | [Page] |
This document describes procedures for using Bidirectional Forwarding Detection (BFD) for multipoint networks to detect data plane failures in Multiprotocol Label Switching (MPLS) point-to-multipoint (p2mp) Label Switched Paths (LSPs) and Segment Routing (SR) point-to-multipoint policies with SR-MPLS data plane.¶
It also describes the applicability of LSP Ping, as in-band, and the control plane, as out-band, solutions to bootstrap a BFD session.¶
It also describes the behavior of the active tail for head notification.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 14 August 2022.¶
Copyright (c) 2022 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
[RFC8562] defines a method of using Bidirectional Detection (BFD) [RFC5880] to monitor and detect unicast failures between the sender (head) and one or more receivers (tails) in multipoint or multicast networks.¶
[RFC8562] added two BFD session types - MultipointHead and MultipointTail. Throughout this document, MultipointHead and MultipointTail refer to the value of the bfd.SessionType is set on a BFD endpoint.¶
This document describes procedures for using such modes of BFD protocol to detect data plane failures in Multiprotocol Label Switching (MPLS) point-to-multipoint (p2mp) Label Switched Paths (LSPs) and Segment Routing (SR) point-to-multipoint policies with SR-MPLS data plane¶
The document also describes the applicability of out-band solutions to bootstrap a BFD session in this environment.¶
It also describes the behavior of the active tail for head notification.¶
MPLS: Multiprotocol Label Switching¶
LSP: Label Switched Path¶
BFD: Bidirectional Forwarding Detection¶
p2mp: Point-to-Multipoint¶
FEC: Forwarding Equivalence Class¶
G-ACh: Generic Associated Channel¶
ACH: Associated Channel Header¶
GAL: G-ACh Label¶
LSR: Label Switching Router¶
SR: Segment Routing¶
SR-MPLS: SR with MPLS data plane¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
[RFC8562] uses BFD in the Demand mode from the very start of a point-to-multipoint (p2mp) BFD session. Because the head doesn't receive any BFD Control packet from a tail, the head of the p2mp BFD session transmits all BFD Control packets with the value of Your Discriminator field set to zero. As a result, a tail cannot demultiplex BFD sessions using Your Discriminator, as defined in [RFC5880]. [RFC8562] requires that to demultiplex BFD sessions, the tail uses the source IP address, My Discriminator, and the identity of the multipoint tree from which the BFD Control packet was received. If the BFD Control packet is encapsulated in IP/UDP, then the source IP address MUST be used to demultiplex the received BFD Control packet as described in Section 3.1. The non-IP encapsulation case is described in Section 3.2.¶
[RFC8562] defines IP/UDP encapsulation for multipoint BFD over p2mp MPLS LSP:¶
The Motivation section [RFC6790] lists several advantages of generating the entropy value by an ingress Label Switching Router (LSR) compared to when a transit LSR infers entropy using the information in the MPLS label stack or payload. Thus this specification further clarifies that:¶
In some environments, the overhead of extra IP/UDP encapsulations may be considered burdensome, making the use of more compact G-ACh encapsulation attractive. Also, the validation of the IP/UDP encapsulation of a BFD Control packet in a p2mp BFD session may fail because of a problem related to neither the MPLS label stack nor to BFD. Avoiding unnecessary encapsulation of p2mp BFD over an MPLS LSP improves the accuracy of the correlation of the detected failure and defect in MPLS LSP. Non-IP encapsulation for multipoint BFD over p2mp MPLS LSP (shown in Figure 1) MUST use Generic Associated Channel (G-ACh) Label (GAL) (see [RFC5586]) at the bottom of the label stack followed by an Associated Channel Header (ACH). If a BFD Control packet in PW-ACH encapsulation (without IP/UDP Headers) is to be used in ACH, an implementation would not be able to verify the identity of the MultipointHead and, as a result, will not properly demultiplex BFD packets. Hence, a new channel type value is needed. The Channel Type field in ACH MUST be set to TBA1 value Section 7. To provide the identity of the MultipointHead for the particular multipoint BFD session, a Source Address TLV, as defined in Section 4.1 [RFC7212], MUST immediately follow a BFD Control message.¶
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LSP Label | TC |S| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| GAL | TC |1| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 1|Version| Reserved | Channel Type = TBA1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ BFD Control Message ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type=0 | Reserved | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved (16 bits) | Address Family (16 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Address ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LSP Ping is the part of the on-demand OAM toolset used to detect and localize defects in the data plane and verify the control plane against the data plane by ensuring that the LSP is mapped to the same FEC at both egress and ingress endpoints.¶
LSP Ping, as defined in [RFC6425], MAY be used to bootstrap MultipointTail. If LSP Ping is used, it MUST include the Target FEC TLV and the BFD Discriminator TLV defined in [RFC5884]. For the case of p2mp MPLS LSP, the Target FEC TLV MUST use sub-TLVs defined in Section 3.1 [RFC6425]. For the case of p2mp SR policy with SR-MPLS data plane, an implementation of this specification MUST follow procedures defined in [RFC8287]. Setting the value of Reply Mode field to "Do not reply" [RFC8029] for the LSP Ping to bootstrap MultipointTail of the p2mp BFD session is RECOMMENDED. Indeed, because BFD over a multipoint network uses BFD Demand mode, the LSP echo reply from a tail has no useful information to convey to the head, unlike in the case of the BFD over a p2p MPLS LSP [RFC5884]. A MultipointTail that receives an LSP Ping that includes the BFD Discriminator TLV:¶
Besides bootstrapping a BFD session over a p2mp LSP, LSP Ping SHOULD be used to verify the control plane against the data plane periodically by checking that the p2mp LSP is mapped to the same FEC at the MultipointHead and all active MultipointTails. The rate of generation of these LSP Ping Echo request messages SHOULD be significantly less than the rate of generation of the BFD Control packets because LSP Ping requires more processing to validate the consistency between the data plane and the control plane. An implementation MAY provide configuration options to control the rate of generation of the periodic LSP Ping Echo request messages.¶
The BGP-BFD Attribute [RFC9026] MAY be used to bootstrap multipoint BFD session on a tail.¶
[RFC8562] defined how the BFD Demand mode can be used in multipoint networks. When applied in MPLS, procedures specified in [RFC8562] allow an egress LSR to detect a failure of the part of the MPLS p2mp LSP from the ingress LSR. The ingress LSR is not aware of the state of the p2mp LSP. [RFC8563], using mechanisms defined in [RFC8562], defined an "active tail" behavior. An active tail might notify the head of the detected failure and responds to a poll sequence initiated by the head. The first method, referred to as Head Notification without Polling, is mentioned in Section 5.2.1 [RFC8563], is the simplest of all described in [RFC8563]. The use of this method in BFD over MPLS p2mp LSP is discussed in this document. Analysis of other methods of a head learning of the state of an MPLS p2mp LSP is outside the scope of this document.¶
As specified in [RFC8563] for the active tail mode, BFD variables MUST be as follows:¶
On an ingress LSR:¶
On an egress LSR:¶
In Section 5.2.1 [RFC8563] is noted that "the tail sends unsolicited BFD packets in response to the detection of a multipoint path failure" but without the specifics on the information in the packet and frequency of transmissions. This document defines below the procedure of an active tail with unsolicited notifications for p2mp MPLS LSP.¶
Upon detecting the failure of the p2mp MPLS LSP, an egress LSR sends BFD Control packet with the following settings:¶
An ingress LSR that has received the BFD Control packet, as described above, sends the unicast IP/UDP encapsulated BFD Control packet with the Final (F) bit set to the egress LSR.¶
This document does not introduce new security aspects but inherits all security considerations from [RFC5880], [RFC5884], [RFC7726], [RFC8562], [RFC8029], and [RFC6425].¶
Also, BFD for p2mp MPLS LSP MUST follow the requirements listed in section 4.1 [RFC4687] to avoid congestion in the control plane or the data plane caused by the rate of generating BFD Control packets. An operator SHOULD consider the amount of extra traffic generated by p2mp BFD when selecting the interval at which the MultipointHead will transmit BFD Control packets. The operator MAY consider the size of the packet the MultipointHead transmits periodically as using IP/UDP encapsulation, which adds up to 28 octets, more than 50% of the BFD Control packet length, comparing to G-ACh encapsulation.¶
IANA is requested to allocate value (TBA1) from its MPLS Generalized Associated Channel (G-ACh) Types registry.¶
| Value | Description | Reference |
|---|---|---|
| TBA1 | Multipoint BFD Session | This document |
The authors sincerely appreciate the comments received from Andrew Malis, Italo Busi, Shraddha Hegde, and thought stimulating questions from Carlos Pignataro.¶