Internet-Draft draft-ietf-ipsecme-mib-iptfs-11 October 2022
Fedyk & Kinzie Expires 24 April 2023 [Page]
Workgroup:
Network Working Group
Internet-Draft:
draft-ietf-ipsecme-mib-iptfs-11
Published:
Intended Status:
Standards Track
Expires:
Authors:
D. Fedyk
LabN Consulting, L.L.C.
E. Kinzie
LabN Consulting, L.L.C.

Definitions of Managed Objects for IP Traffic Flow Security

Abstract

This document describes managed objects for the management of IP Traffic Flow Security additions to IKEv2 and IPsec. This document provides a read only version of the objects defined in the YANG module for the same purpose.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 24 April 2023.

▲

Table of Contents

1. Introduction

This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community. Traffic Flow Security (IP-TFS) extensions as defined in [I-D.ietf-ipsecme-iptfs] are enhancements to an IPsec tunnel Security Association to provide improved traffic confidentiality.

For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of [RFC3410].

Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, [RFC2578], STD 58, [RFC2579] and STD 58, [RFC2580].

The objects defined here are the same as [I-D.ietf-ipsecme-yang-iptfs] with the exception that only operational or state data is supported. By making operational data accessible via SNMP existing network management systems can monitor IP-TFS. This data is listed in the MIB tree in Section 4.1. This module uses the YANG model as a reference point for managed objects. Note an IETF MIB model for IPsec was never standardized however the structures here could be adapted to existing proprietary MIB implementations where SNMP is used to manage networks.

2. Terminology & Concepts

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

3. Overview

This document defines the MIB for access to operational parameters of IP traffic flow security (IP-TFS). IP-TFS, defined in [I-D.ietf-ipsecme-iptfs], configures a security association for tunnel mode IPsec with characteristics that improve traffic confidentiality and reduce bandwidth efficiency loss.

This document is based on the concepts and management model defined in [I-D.ietf-ipsecme-yang-iptfs]. This document assumes familiarity with IP security concepts described in [RFC4301], IP-TFS as described in [I-D.ietf-ipsecme-iptfs] and the IP-TFS management model described in [I-D.ietf-ipsecme-yang-iptfs].

This document specifies an extensible operational model for IP-TFS. It reuses the management model defined in [I-D.ietf-ipsecme-yang-iptfs]. It allows SNMP systems to read operational objects (which includes configured objects) from IP-TFS.

4. Management Objects

4.1. MIB Tree

The following is the MIB registration tree diagram for the IP-TFS extensions.

# IP-TRAFFIC-FLOW-SECURITY-MIB registration tree

--iptfsMIB(1.3.6.1.2.1.500)
  +--iptfsMIBObjects(1)
  |  +--iptfsGroup(1)
  |  |  +--iptfsConfigTable(1)
  |  |     +--iptfsConfigTableEntry(1) [iptfsConfigSaIndex]
  |  |        |
  |  |        +-- --- Integer32           iptfsConfigSaIndex(1)
  |  |        +-- r-n TruthValue          congestionControl(2)
  |  |        +-- r-n TruthValue          usePathMtuDiscovery(3)
  |  |        +-- r-n UnsignedShort       outerPacketSize(4)
  |  |        +-- r-n CounterBasedGauge64 l2FixedRate(5)
  |  |        +-- r-n CounterBasedGauge64 l3FixedRate(6)
  |  |        +-- r-n TruthValue          dontFragment(7)
  |  |        +-- r-n NanoSeconds         maxAggregationTime(8)
  |  |        +-- r-n UnsignedShort       windowSize(9)
  |  |        +-- r-n TruthValue          sendImmediately(10)
  |  |        +-- r-n NanoSeconds         lostPacketTimerInterval(11)
  |  +--ipsecStatsGroup(2)
  |  |  +--ipsecStatsTable(1)
  |  |     +--ipsecStatsTableEntry(1) [ipsecSaIndex]
  |  |        +-- --- Integer32 ipsecSaIndex(1)
  |  |        +-- r-n Counter64 txPkts(2)
  |  |        +-- r-n Counter64 txOctets(3)
  |  |        +-- r-n Counter64 txDropPkts(4)
  |  |        +-- r-n Counter64 rxPkts(5)
  |  |        +-- r-n Counter64 rxOctets(6)
  |  |        +-- r-n Counter64 rxDropPkts(7)
  |  +--iptfsInnerStatsGroup(3)
  |  |  +--iptfsInnerStatsTable(1)
  |  |     +--iptfsInnerStatsTableEntry(1) [iptfsInnerSaIndex]
  |  |        +-- --- Integer32 iptfsInnerSaIndex(1)
  |  |        +-- r-n Counter64 txInnerPkts(2)
  |  |        +-- r-n Counter64 txInnerOctets(3)
  |  |        +-- r-n Counter64 rxInnerPkts(4)
  |  |        +-- r-n Counter64 rxInnerOctets(5)
  |  |        +-- r-n Counter64 rxIncompleteInnerPkts(6)
  |  +--iptfsOuterStatsGroup(4)
  |     +--iptfsOuterStatsTable(1)
  |        +--iptfsOuterStatsTableEntry(1) [iptfsSaIndex]
  |           +-- --- Integer32 iptfsSaIndex(1)
  |           +-- r-n Counter64 txExtraPadPkts(2)
  |           +-- r-n Counter64 txExtraPadOctets(3)
  |           +-- r-n Counter64 txAllPadPkts(4)
  |           +-- r-n Counter64 txAllPadOctets(5)
  |           +-- r-n Counter64 rxExtraPadPkts(6)
  |           +-- r-n Counter64 rxExtraPadOctets(7)
  |           +-- r-n Counter64 rxAllPadPkts(8)
  |           +-- r-n Counter64 rxAllPadOctets(9)
  |           +-- r-n Counter64 rxErroredPkts(10)
  |           +-- r-n Counter64 rxMissedPkts(11)
  +--iptfsMIBConformance(2)
     +--iptfsMIBConformances(1)
     |  +--iptfsMIBCompliance(1)
     +--iptfsMIBGroups(2)
        +--iptfsMIBConfGroup(1)
        +--ipsecStatsConfGroup(2)
        +--iptfsInnerStatsConfGroup(3)
        +--iptfsOuterStatsConfGroup(4)

4.2. SNMP

The following is the MIB for IP-TFS. The Congestion control algorithm in [RFC5348] is referenced in the MIB text.

<CODE BEGINS> file "iptfs-mib.mib"
=-->
-- *----------------------------------------------------------------
-- *  IP-TRAFFIC-FLOW-SECURITY-MIB Module
-- *----------------------------------------------------------------

IP-TRAFFIC-FLOW-SECURITY-MIB DEFINITIONS ::= BEGIN
   IMPORTS
        MODULE-IDENTITY, OBJECT-TYPE,
        Integer32, Unsigned32, Counter64, mib-2
            FROM SNMPv2-SMI
        CounterBasedGauge64
            FROM  HCNUM-TC
        MODULE-COMPLIANCE, OBJECT-GROUP
            FROM SNMPv2-CONF
        TEXTUAL-CONVENTION,
        TruthValue
            FROM SNMPv2-TC;

   iptfsMIB MODULE-IDENTITY
        LAST-UPDATED "202210210000Z"
        ORGANIZATION "IETF IPsecme Working Group"
        CONTACT-INFO
                "
                   Author: Don Fedyk
                           <mailto:dfedyk@labn.net>

                   Author: Eric Kinzie
                           <mailto:ekinzie@labn.net>"

-- RFC Ed.: replace XXXX with actual RFC number, update mib-2
-- entry and remove this note.

   DESCRIPTION
      "This module defines the configuration and operational
      state for managing the IP Traffic Flow Security
      functionality [RFC XXXX].  Copyright (c) 2022 IETF
      Trust and the persons identified as authors of the
      code. All rights reserved.

      Redistribution and use in source and binary forms,
      with or without modification, is permitted pursuant
      to, and subject to the license terms contained in,
      the Simplified BSD License set forth in Section 4.c
      of the IETF Trust's Legal Provisions Relating to IETF
      Documents (https://trustee.ietf.org/license-info).

      This version of this SNMP MIB module is part of RFC XXXX
      (https://tools.ietf.org/html/rfcXXXX); see the RFC
      itself for full legal notices."


    REVISION "202210210000Z"
    DESCRIPTION
            "Initial revision. Derived from the IP-TFS Yang Model."
    ::= { mib-2 500}
--
-- Textual Conventions
--

UnsignedShort ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "d"
    STATUS      current
    DESCRIPTION "xs:unsignedShort"
    SYNTAX      Unsigned32 (0 .. 65535)


NanoSeconds ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "d-6"
    STATUS  current
    DESCRIPTION
      "Represents time unit value in nanoseconds."
    SYNTAX      Integer32


-- Objects, Notifications & Conformances

   iptfsMIBObjects     OBJECT IDENTIFIER
               ::= { iptfsMIB 1 }
   iptfsMIBConformance OBJECT IDENTIFIER
               ::= { iptfsMIB 2}

--
-- IP-TFS MIB Object Groups
--
   iptfsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 1 }

   ipsecStatsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 2 }

   iptfsInnerStatsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 3 }

   iptfsOuterStatsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 4 }

   iptfsConfigTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IptfsConfigTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
               "The table containing configuration information for
               IP-TFS."
       ::= { iptfsGroup 1 }

   iptfsConfigTableEntry OBJECT-TYPE
       SYNTAX     IptfsConfigTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "An entry (conceptual row) containing the information on
         a particular IP-TFS SA."
       INDEX      { iptfsConfigSaIndex }
       ::= { iptfsConfigTable 1 }

  IptfsConfigTableEntry ::= SEQUENCE {
      iptfsConfigSaIndex         Integer32,

   -- identifier information
      congestionControl          TruthValue,
      usePathMtuDiscovery        TruthValue,
      outerPacketSize            UnsignedShort,
      l2FixedRate                CounterBasedGauge64,
      l3FixedRate                CounterBasedGauge64,
      dontFragment               TruthValue,
      maxAggregationTime         NanoSeconds,
      windowSize                 UnsignedShort,
      sendImmediately            TruthValue,
      lostPacketTimerInterval    NanoSeconds
   }

   iptfsConfigSaIndex OBJECT-TYPE
       SYNTAX      Integer32 (1..16777215)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
         "A unique value, greater than zero, for each SA.
         It is recommended that values are assigned contiguously
         starting from 1.

         The value for each entry must remain constant at least
         from one re-initialization of entity's network management
         system to the next re-initialization."
       ::= { iptfsConfigTableEntry 1 }

    congestionControl OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "When set to true, the default, this enables the
          congestion control on-the-wire exchange of data that is
          required by congestion control algorithms as defined by
          RFC 5348.  When set to false, IP-TFS sends fixed-sized
          packets over an IP-TFS tunnel at a constant rate."
        ::= { iptfsConfigTableEntry 2 }

    usePathMtuDiscovery OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "Packet size is either auto-discovered or manually
          configured. If usePathMtuDiscovery is true the system
          utilizes path-mtu to determine maximum IP-TFS packet
          size.  If the packet size is explicitly configured
          then it will only be adjusted downward if use-path-mtu
          is set."
        ::= { iptfsConfigTableEntry 3 }

    outerPacketSize OBJECT-TYPE
        SYNTAX      UnsignedShort
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On Transmission, the size of the outer encapsulating
          tunnel packet (i.e., the IP packet containing the ESP
          payload)."
        ::= { iptfsConfigTableEntry 4 }

    l2FixedRate OBJECT-TYPE
        SYNTAX      CounterBasedGauge64
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "IP-TFS bit rate may be specified as a layer 2 wire rate.
          On transmission, target bandwidth/bit rate in bps for
          IP-TFS tunnel. This rate is the nominal timing for the
          fixed size packet. If congestion control is enabled the
          rate may be adjusted down."
        ::= { iptfsConfigTableEntry 5 }

    l3FixedRate OBJECT-TYPE
        SYNTAX      CounterBasedGauge64
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "IP-TFS bit rate may be specified as a layer 3 packet rate.
          On Transmission, target bandwidth/bit rate in bps for
          IP-TFS tunnel.  This rate is the nominal timing for the
          fixed size packet. If congestion control is enabled the
          rate may be adjusted down."
        ::= { iptfsConfigTableEntry 6 }

    dontFragment OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On transmission, disable packet fragmentation across
          consecutive IP-TFS tunnel packets; inner packets larger
          than what can be transmitted in outer packets will be
          dropped."
        ::= { iptfsConfigTableEntry 7 }

    maxAggregationTime OBJECT-TYPE
        SYNTAX      NanoSeconds
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On transmission, maximum aggregation time is the
           maximum length of time a received inner packet can be
           held prior to transmission in the IP-TFS tunnel. Inner
           packets that would be held longer than this time, based
           on the current tunnel configuration will be dropped
           rather than be queued for transmission."
        ::= { iptfsConfigTableEntry 8 }

    windowSize OBJECT-TYPE
        SYNTAX      UnsignedShort
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On reception, the maximum number of out-of-order
          packets that will be reordered by an IP-TFS receiver
          while performing the reordering operation. The value 0
          disables any reordering."
        ::= { iptfsConfigTableEntry 9 }

    sendImmediately OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On reception, send inner packets as soon as possible, do
          not wait for lost or misordered outer packets.
          Selecting this option reduces the inner (user) packet
          delay but can amplify out-of-order delivery of the inner
          packet stream in the presence of packet aggregation and
          any reordering."
        ::= { iptfsConfigTableEntry 10 }

    lostPacketTimerInterval OBJECT-TYPE
        SYNTAX      NanoSeconds
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On reception, this interval defines the length of time
          an IP-TFS receiver will wait for a missing packet before
          considering it lost.  If not using send-immediately,
          then each lost packet will delay inner (user) packets
          until this timer expires. Setting this value too low can
          impact reordering and reassembly."
        ::= { iptfsConfigTableEntry 11 }

   ipsecStatsTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IpsecStatsTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "The table containing basic statistics on IPsec."
       ::= { ipsecStatsGroup 1 }


    ipsecStatsTableEntry OBJECT-TYPE
       SYNTAX     IpsecStatsTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "An entry (conceptual row) containing the information on
         a particular IKE SA."
       INDEX      { ipsecSaIndex }
       ::= { ipsecStatsTable 1 }

     IpsecStatsTableEntry ::= SEQUENCE {
     ipsecSaIndex               Integer32,
-- packet statistics information
     txPkts                     Counter64,
     txOctets                   Counter64,
     txDropPkts                 Counter64,
     rxPkts                     Counter64,
     rxOctets                   Counter64,
     rxDropPkts                 Counter64
   }

   ipsecSaIndex OBJECT-TYPE
      SYNTAX      Integer32 (1..16777215)
      MAX-ACCESS  not-accessible
      STATUS      current
      DESCRIPTION
        "A unique value, greater than zero, for each SA.
        It is recommended that values are assigned contiguously
        starting from 1.

        The value for each entry must remain constant at least
        from one re-initialization of entity's network management
        system to the next re-initialization."
      ::= { ipsecStatsTableEntry 1 }


   txPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Outbound Packet count."
       ::= { ipsecStatsTableEntry 2 }

   txOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Outbound Packet bytes."
       ::= { ipsecStatsTableEntry 3 }

   txDropPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Outbound dropped packets count."
       ::= { ipsecStatsTableEntry 4 }

   rxPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Inbound Packet count."
       ::= { ipsecStatsTableEntry 5 }

   rxOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Inbound Packet bytes."
       ::= { ipsecStatsTableEntry 6 }

   rxDropPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Inbound Dropped packets"
       ::= { ipsecStatsTableEntry 7 }

   iptfsInnerStatsTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IptfsInnerSaEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "The table containing information on IP-TFS
         Inner Packets."
       ::= { iptfsInnerStatsGroup 1 }

   iptfsInnerStatsTableEntry OBJECT-TYPE
      SYNTAX     IptfsInnerSaEntry
      MAX-ACCESS not-accessible
      STATUS     current
      DESCRIPTION
        "An entry containing the information on
        a particular IP-TFS SA."
      INDEX      { iptfsInnerSaIndex }
      ::= { iptfsInnerStatsTable 1 }

     IptfsInnerSaEntry ::= SEQUENCE {
     iptfsInnerSaIndex          Integer32,

     txInnerPkts                Counter64,
     txInnerOctets              Counter64,
     rxInnerPkts                Counter64,
     rxInnerOctets              Counter64,
     rxIncompleteInnerPkts      Counter64
    }

   iptfsInnerSaIndex OBJECT-TYPE
      SYNTAX      Integer32 (1..16777215)
      MAX-ACCESS  not-accessible
      STATUS      current
      DESCRIPTION
        "A unique value, greater than zero, for each SA.
        It is recommended that values are assigned contiguously
        starting from 1.

        The value for each entry must remain constant at least
        from one re-initialization of entity's network management
        system to the next re-initialization."
      ::= { iptfsInnerStatsTableEntry 1 }

   txInnerPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner packets sent. This count
         is whole packets only.  A fragmented packet counts as
         one packet."
       ::= { iptfsInnerStatsTableEntry 2 }

   txInnerOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner octets sent.  This is
         inner packet octets only.  Does not count padding."
       ::= { iptfsInnerStatsTableEntry 3 }

   rxInnerPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner packets received."
       ::= { iptfsInnerStatsTableEntry 4 }

       rxInnerOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner octets received.  Does
         not include padding or overhead."
       ::= { iptfsInnerStatsTableEntry 5 }

   rxIncompleteInnerPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner packets that were
         incomplete.  Usually this is due to fragments not
         received. Also, this may be due to misordering or
         errors in received outer packets."
    ::= { iptfsInnerStatsTableEntry 6 }

  iptfsOuterStatsTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IptfsOuterSaEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "The table containing information on IP-TFS."
       ::= { iptfsOuterStatsGroup 1 }

   iptfsOuterStatsTableEntry OBJECT-TYPE
      SYNTAX     IptfsOuterSaEntry
      MAX-ACCESS not-accessible
      STATUS     current
      DESCRIPTION
        "An entry containing the information on
        a particular IP-TFS SA."
      INDEX      { iptfsSaIndex }
      ::= { iptfsOuterStatsTable 1 }

     IptfsOuterSaEntry ::= SEQUENCE {
     iptfsSaIndex               Integer32,

  -- iptfs packet statistics information
     txExtraPadPkts             Counter64,
     txExtraPadOctets           Counter64,
     txAllPadPkts               Counter64,
     txAllPadOctets             Counter64,
     rxExtraPadPkts             Counter64,
     rxExtraPadOctets           Counter64,
     rxAllPadPkts               Counter64,
     rxAllPadOctets             Counter64,
     rxErroredPkts              Counter64,
     rxMissedPkts               Counter64
    }


   iptfsSaIndex OBJECT-TYPE
      SYNTAX      Integer32 (1..16777215)
      MAX-ACCESS  not-accessible
      STATUS      current
      DESCRIPTION
        "A unique value, greater than zero, for each SA.
        It is recommended that values are assigned contiguously
        starting from 1.

        The value for each entry must remain constant at least
        from one re-initialization of entity's network management
        system to the next re-initialization."
      ::= { iptfsOuterStatsTableEntry 1 }

   txExtraPadPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of transmitted outer IP-TFS packets that
         included some padding."
       ::= { iptfsOuterStatsTableEntry 2 }

   txExtraPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of transmitted octets of padding added to
         outer IP-TFS packets with data."
       ::= { iptfsOuterStatsTableEntry 3 }

   txAllPadPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of transmitted IP-TFS packets that were
         all padding with no inner packet data."
       ::= { iptfsOuterStatsTableEntry 4 }

   txAllPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number transmitted octets of padding added to
         IP-TFS packets with no inner packet data."
       ::= { iptfsOuterStatsTableEntry 5 }

   rxExtraPadPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of received outer IP-TFS packets that
         included some padding."
       ::= { iptfsOuterStatsTableEntry 6 }

   rxExtraPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of received octets of padding added to
         outer IP-TFS packets with data."
       ::= { iptfsOuterStatsTableEntry 7 }

   rxAllPadPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of received IP-TFS packets that were all
         padding with no inner packet data."
       ::= { iptfsOuterStatsTableEntry 8 }

   rxAllPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number received octets of padding added to
         IP-TFS packets with no inner packet data."
       ::= { iptfsOuterStatsTableEntry 9 }

   rxErroredPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS outer packets dropped due to
         errors."
       ::= { iptfsOuterStatsTableEntry 10 }

   rxMissedPkts OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS outer packets missing indicated
         by missing sequence number."
       ::= { iptfsOuterStatsTableEntry 11 }

--
-- Iptfs Module Compliance
--

iptfsMIBConformances OBJECT IDENTIFIER
                    ::= { iptfsMIBConformance 1 }

iptfsMIBGroups OBJECT IDENTIFIER
                    ::= { iptfsMIBConformance 2 }

iptfsMIBCompliance MODULE-COMPLIANCE
        STATUS  current
        DESCRIPTION
                "The compliance statement for entities which
                implement the IP-TFS MIB"
        MODULE  -- this module
                MANDATORY-GROUPS {
                 iptfsMIBConfGroup,
                 ipsecStatsConfGroup,
                 iptfsInnerStatsConfGroup,
                 iptfsOuterStatsConfGroup
                }

        ::= { iptfsMIBConformances 1 }

--
-- MIB Groups (Units of Conformance)
--

iptfsMIBConfGroup OBJECT-GROUP
        OBJECTS {
                congestionControl,
                usePathMtuDiscovery,
                outerPacketSize ,
                l2FixedRate ,
                l3FixedRate ,
                dontFragment,
                maxAggregationTime,
                windowSize,
                sendImmediately,
                lostPacketTimerInterval
        }
        STATUS  current
        DESCRIPTION
                "A collection of objects providing per SA IP-TFS
                Configuration."
        ::= { iptfsMIBGroups 1 }

ipsecStatsConfGroup OBJECT-GROUP
        OBJECTS {
                txPkts,
                txOctets,
                txDropPkts,
                rxPkts,
                rxOctets,
                rxDropPkts
        }
        STATUS  current
        DESCRIPTION
          "A collection of objects providing per SA Basic
          Stats."
        ::= { iptfsMIBGroups 2 }

iptfsInnerStatsConfGroup OBJECT-GROUP
        OBJECTS {
                txInnerPkts,
                txInnerOctets,
                rxInnerPkts,
                rxInnerOctets,
                rxIncompleteInnerPkts
        }
        STATUS  current
        DESCRIPTION
          "A collection of objects providing per SA IP-TFS
          Inner Packet Statistics."
        ::= { iptfsMIBGroups 3 }


iptfsOuterStatsConfGroup OBJECT-GROUP
        OBJECTS {
                txExtraPadPkts,
                txExtraPadOctets,
                txAllPadPkts,
                txAllPadOctets,
                rxExtraPadPkts,
                rxExtraPadOctets,
                rxAllPadPkts,
                rxAllPadOctets,
                rxErroredPkts,
                rxMissedPkts
        }
        STATUS  current
        DESCRIPTION
          "A collection of objects providing per SA IP-TFS
          Outer Packet Statistics."
        ::= { iptfsMIBGroups 4 }

END

<CODE ENDS>

5. IANA Considerations

The MIB module in this document uses the following IANA-assigned OBJECT IDENTIFIER value, recorded in the SMI Network Management MGMT Codes Internet-standard MIB - registry:

Name     Description                        OBJECT IDENTIFIER value
-------  ---------------------------------  ----------------------
iptfsMIB IP-TRAFFIC-FLOW-SECURITY-MIB       { mib-2 TBA-IANA }

6. Security Considerations

The MIB specified in this document can read the operational behavior of IP traffic flow security. For the implications regarding write configuration consult the [I-D.ietf-ipsecme-iptfs] which defines the functionality.

There are no management objects defined in this MIB module that have a MAX-ACCESS clause of read-write and/or read-create. So, if this MIB module is implemented correctly, then there is no risk that an intruder can alter or create any management objects of this MIB module via direct SNMP SET operations.

Some of the objects in this MIB module may be considered sensitive or vulnerable in some network environments. This includes INDEX objects with a MAX-ACCESS of not-accessible, and any indices from other modules exposed via AUGMENTS. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:

SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), there is no control as to who on the secure network is allowed to access and GET (read) the objects in this MIB module.

To prevent unauthorized access to SNMP including access to IP-TFS sensitive objects:

7. Acknowledgements

The authors would like to thank Chris Hopps, Lou Berger and Tero Kivinen for their help and feedback on the MIB model.

8. References

8.1. Normative References

[I-D.ietf-ipsecme-iptfs]
Hopps, C., "IP-TFS: Aggregation and Fragmentation Mode for ESP and its Use for IP Traffic Flow Security", Work in Progress, Internet-Draft, draft-ietf-ipsecme-iptfs-19, , <https://www.ietf.org/archive/id/draft-ietf-ipsecme-iptfs-19.txt>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC2578]
McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, DOI 10.17487/RFC2578, , <https://www.rfc-editor.org/info/rfc2578>.
[RFC2579]
McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, DOI 10.17487/RFC2579, , <https://www.rfc-editor.org/info/rfc2579>.
[RFC3414]
Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", STD 62, RFC 3414, DOI 10.17487/RFC3414, , <https://www.rfc-editor.org/info/rfc3414>.
[RFC3826]
Blumenthal, U., Maino, F., and K. McCloghrie, "The Advanced Encryption Standard (AES) Cipher Algorithm in the SNMP User-based Security Model", RFC 3826, DOI 10.17487/RFC3826, , <https://www.rfc-editor.org/info/rfc3826>.
[RFC5591]
Harrington, D. and W. Hardaker, "Transport Security Model for the Simple Network Management Protocol (SNMP)", STD 78, RFC 5591, DOI 10.17487/RFC5591, , <https://www.rfc-editor.org/info/rfc5591>.
[RFC5592]
Harrington, D., Salowey, J., and W. Hardaker, "Secure Shell Transport Model for the Simple Network Management Protocol (SNMP)", RFC 5592, DOI 10.17487/RFC5592, , <https://www.rfc-editor.org/info/rfc5592>.
[RFC6353]
Hardaker, W., "Transport Layer Security (TLS) Transport Model for the Simple Network Management Protocol (SNMP)", STD 78, RFC 6353, DOI 10.17487/RFC6353, , <https://www.rfc-editor.org/info/rfc6353>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.

8.2. Informative References

[I-D.ietf-ipsecme-yang-iptfs]
Fedyk, D. and C. Hopps, "A YANG Data Model for IP Traffic Flow Security", Work in Progress, Internet-Draft, draft-ietf-ipsecme-yang-iptfs-11, , <https://www.ietf.org/archive/id/draft-ietf-ipsecme-yang-iptfs-11.txt>.
[RFC2580]
McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Conformance Statements for SMIv2", STD 58, RFC 2580, DOI 10.17487/RFC2580, , <https://www.rfc-editor.org/info/rfc2580>.
[RFC3410]
Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, DOI 10.17487/RFC3410, , <https://www.rfc-editor.org/info/rfc3410>.
[RFC4301]
Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, DOI 10.17487/RFC4301, , <https://www.rfc-editor.org/info/rfc4301>.
[RFC5348]
Floyd, S., Handley, M., Padhye, J., and J. Widmer, "TCP Friendly Rate Control (TFRC): Protocol Specification", RFC 5348, DOI 10.17487/RFC5348, , <https://www.rfc-editor.org/info/rfc5348>.

Authors' Addresses

Don Fedyk
LabN Consulting, L.L.C.
Eric Kinzie
LabN Consulting, L.L.C.