| Internet-Draft | PAM for Multi-SLO | March 2023 |
| Mirsky, et al. | Expires 9 September 2023 | [Page] |
This document defines a set of metrics for networking services with performance requirements expressed as Service Level Objectives (SLO). These metrics, referred to as Precision Availability Metrics (PAM), are useful for defining and monitoring of SLOs. For example, PAM can be used by providers and/or users of the Network Slice service to assess whether the service is provided in compliance with its specified quality, i.e., in accordance with its defined SLOs.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 9 September 2023.¶
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
Network operators and network users often need to assess the quality with which network services are being provided and delivered. In particular in cases where service level guarantees are given and service level objectives (SLOs) are defined, it is essential to provide a measure of the degree with which actual service levels that are delivered comply with SLOs that were agreed, typically in a contract or agreement. Examples of service levels include service latency and packet loss. Simple examples of SLOs associated with such service levels would be target values for the maximum packet delay (one-way and/or round trip) or maximum packet loss ratio that would be deemed acceptable.¶
An example of an SLO is one that characterizes the continued ability of a particular set of nodes to communicate. Essentially, the absence of what is, in other contexts, is called a defect. The SLO would include the various time and measurement aspects that would be interpreted as a defect or failure to communicate. It is important to note that it is being defined as a state, and thus, it has conditions that define entry into it and exit out of it. It is expected that a Service Level Agreement (SLA) includes a defect-related SLO, possibly in addition to other SLOs.¶
To express the perceived quality of delivered networking services versus their SLOs, a set of metrics are needed to characterize the quality of the service being provided. Of concern is not so much the absolute service level (for example, actual latency experienced), but whether the service is provided in accordance with the negotiated, and eventually contracted, service levels. For instance, this may include whether the packet delay that is experienced falls within an acceptable range that has been contracted for the service. The specific quality of service depends on the SLO that is in effect. A non-conformance to an SLO might result in degradation of the quality of experience for gamers or even jeopardize the safety of a large geographical area. However, as those applications represent clear business opportunities, they demand dependable technical solutions.¶
The same service level may be deemed acceptable for one application, while unacceptable for another, depending on the needs of the application. Hence it is not sufficient to simply measure service levels per se over time, but to assess the quality of the service being contextually provided (e.g., with the applicable SLO in mind). However, at this point, there are no standard metrics in place that can be used to account for the quality with which services are delivered relative to their SLOs, and whether their SLOs are being met at all times. Such metrics and the instrumentation to support them are essential for a number of purposes, including monitoring (to ensure that networking services are performing according to their objectives) as well as accounting (to maintain a record of service levels delivered, important for monetization of such services as well as for triaging of problems).¶
The current state-of-the-art of metrics available today includes, for example, interface metrics, useful to obtain data on traffic volume and behavior that can be observed at an interface [RFC2863] and [RFC8343]. However, they are agnostic of actual service levels and not specific to distinct flows. Flow records [RFC7011] and [RFC7012] maintain statistics about flows, including flow volume and flow duration, but again, contain very little information about end-to-end service levels, let alone whether the service levels delivered to meet their targets, i.e., their associated SLOs.¶
This specification introduces a new set of metrics, Precision Availability Metrics (PAM), aimed at capturing end-to-end service levels for a flow, specifically the degree to which flows comply with the SLOs that are in effect. PAM can be used to assess whether a service is provided in compliance with its specified quality, i.e., in accordance with its defined SLOs. This information can be used in multiple ways, for example, to optimize service delivery, take timely counteractions in the event of service degradation, or account for the quality of services being delivered.¶
Availability is discussed in Section 3.4 of [RFC7297]. In this document, the term "availability" reflects that a service that is characterized by its SLOs is considered unavailable whenever those SLOs are violated, even if basic connectivity is still working. "Precision" refers to the fact that services whose end-to-end service levels are governed by SLOs, and which must therefore be precisely delivered according to the associated quality and performance requirements. It should be noted that precision refers to what is being assessed, not the mechanism used to measure it; in other words, it does not refer to the precision of the mechanism with which actual service levels are measured. Furthermore, the precision, with respect to the delivery of an SLO, only applies when the metric value approaches the specified threshold levels in the SLO. The specification and implementation of methods that provide for accurate measurements is a separate topic independent of the definition of the metrics in which the results of such measurements would be expressed.¶
Service Level Expectations (SLEs), as defined in Section 4.1 of [I-D.ietf-teas-ietf-network-slices], are outside the scope of this document, because it is in the nature of SLEs that they define parts of the SLA that are not easily measured.¶
In this document, SLA and SLO are used as defined in Section 4.1 [I-D.ietf-teas-ietf-network-slices].¶
PAM Precision Availability Metric¶
OAM Operations, Administration, and Maintenance¶
SLA Service Level Agreement¶
SLE Service Level Expectations¶
SLO Service Level Objective¶
VI Violated Interval¶
VIR Violated Interval Ratio¶
VPC Violated Packets Count¶
SVI Severely Violated Interval¶
SVIR Severely Violated Interval Ratio¶
SVPC Severely Violated Packets Count¶
VFI Violation-Free Interval¶
When analyzing the availability metrics of a service flow between two nodes, we need to select a time interval as the unit of PAM. In [ITU.G.826], a time interval of one second is used. That is reasonable, but some services may require different granularity. For that reason, the time interval in PAM is viewed as a variable parameter though constant for a particular measurement session. Further, for the purpose of PAM, each time interval, e.g., second or decamillisecond, is classified either as Violated Interval (VI), Severely Violated Interval (SVI), or Violation-Free Interval (VFI ). These are defined as follows:¶
Mechanisms of setting levels of threshold of an SLO are outside the scope for this document.¶
From these defitions, a set of basic metrics can be defined that count the numbers of time intervals that fall into each category:¶
These count metrics are essential in calculating respective ratios (see Section 3.2) that can be used to assess the instability of the service.¶
Beyond accounting for violated intervals, it can sometimes be beneficial also to maintain counts of packets for which a performance threshold is violated. For example, this allows to distinguish between cases in which violated intervals are caused by isolated violation occurrences (such as, a sporadic issue that may be caused by a temporary spike in a queue depth along the packet's path) or by broad violations across multiple packets (such as a problem with slow route reconvergence across the network or more foundational issues such as insufficient network resources). Maintaining such counts and comparing them with the overall amount of traffic also facilitates assessing compliance with statistical SLOs (see Section 4). For these reason, the following additional metrics are defined:¶
A set of metrics can be created based on PAM introduced in Section 3. In this document, these metrics are referred to as derived PAM. Some of these metrics are modeled after Mean Time Between Failure (MTBF) metrics - a "failure" in this context referring to a failure to deliver a packet according to its SLO.¶
An analogous set of metrics can be produced for SVI:¶
To indicate a historic degree of precision availability, additional derived PAMs can be defined as follows:¶
It might be useful for a network operator to determine the current condition of the service for which Precision Availability Metrics are maintained. To facilitate this, it is conceivable to complement PAM with a state model. Such a state model can be used to indicate whether a service is currently considered available or unavailable depending on the network's recent ability to provide service without incurring intervals during which violations occur. It is conceivable to define such a state model in which transitions occur per some predefined PAM settings.¶
While the definition of a service state model is outside the scope of this draft, the following section provides some considerations for how such a state model and accompanying configuration settings could be defined.¶
For example, a state model could be defined by a Finite State Machine featuring two states, "available" and "unavailable". The initial state could be "available". A service could subsequently be deemed as "unavailable" based on the number of successive interval violations that have been recently experienced. To return to a state of "available", a number of intervals without violations would need to be observed.¶
The number of successive intervals with violations, as well as the number of successive intervals that are free of violations, required for a state to transition to another state is defined by a configuration setting. Specifically, the following configuration parameters could be defined:¶
Additional configuration parameters could be defined to account for the severity of violations. Likewise, it is conceivable to define configuration settings that also take VIR and SVIR into account.¶
It should be noted that certain SLAs may be statistical, requiring the service levels of packets in a flow to adhere to specific distributions. For example, an SLA might state that any given SLO applies to at least a certain percentage of packets, allowing for a certain level of, for example, packet loss and/or exceeding packet delay threshold to take place. Each such event, in that case, does not necessarily constitute an SLO violation. However, it is still useful to maintain those statistics, as the number of out-of-SLO packets still matters when looked at in proportion to the total number of packets.¶
Along that vein, an SLA might establish an SLO of, say, end-to-end latency to not exceed 20 ms for 99% of packets, to not exceed 25ms for 99.999% of packets, and to never exceed 30ms for any packet. In that case, any individual packet with latency larger than 20 ms latency and lower than 30 ms cannot be considered an SLO violation in itself, but compliance with the SLO may need to be assessed after the fact.¶
To support statistical SLOs more directly requires additional metrics, such as metrics that represent histograms for service level parameters with buckets corresponding to individual service level objectives. For the example just given, a histogram for a given flow could be maintained with three buckets: one containing the count of packets within 20ms, a second with a count of packets between 20 and 25ms (or simply all within 25ms), a third with a count of packets between 25 and 30ms (or merely all packets within 30ms, and a fourth with a count of anything beyond (or simply a total count). Of course, the number of buckets and the boundaries between those buckets should correspond to the needs of the SLA associated with the application, i.e., to the specific guarantees and SLOs that were provided. The definition of histogram metrics is for further study (see Section 6).¶
PAM provides a number of benefits with other, more conventional performance metrics. Without PAM, it would be possible to conduct ongoing measurements of service levels and maintain a time-series of service level records, then assess compliance with specific SLOs after the fact. However, doing so would require the collection of vast amounts of data that would need to be generated, exported, transmitted, collected, and stored. In addition, extensive postprocessing would be required to compare that data against SLOs and analyze its compliance. Being able to perform these tasks at scale and in real-time would present significant additional challenges.¶
Adding PAM allows for a more compact expression of service level compliance. In that sense, PAM does not simply represent raw data but expresses actionable information. In conjunction with proper instrumentation, PAM can thus help avoid expensive postprocessing.¶
The following is a list of items that are outside the scope of this specification, but which will be useful extensions and opportunities for future work:¶
This document has no IANA actions.¶
Instrumentation for metrics that are used to assess compliance with SLOs constitute an attractive target for an attacker. By interfering with the maintaining of such metrics, services could be falsely identified as complying (when they are not) or vice-versa (i.e., flagged as being non-compliant when indeed they are). While this document does not specify how networks should be instrumented to maintain the identified metrics, such instrumentation needs to be adequately secured to ensure accurate measurements and prohibit tampering with metrics being kept.¶
Where metrics are being defined relative to an SLO, the configuration of those SLOs needs to be adequately secured. Likewise, where SLOs can be adjusted, the correlation between any metrics instance and a particular SLO must be clear. The same service levels that constitute SLO violations for one flow that should be maintained as part of the "violated time units" and related metrics, may be perfectly compliant for another flow. In cases when it is impossible to tie together SLOs and PAM properly, it will be preferable to merely maintain statistics about service levels delivered (for example, overall histograms of end-to-end latency) without assessing which constitutes violations.¶
By the same token, where the definition of what constitutes a "severe" or a "significant" violation depends on configuration settings or context. The configuration of such settings or context needs to be specially secured. Also, the configuration must be bound to the metrics being maintained. This way, it will be clear which configuration setting was in effect when those metrics were being assessed. An attacker that can tamper with such configuration settings will render the corresponding metrics useless (in the best case) or misleading (in the worst case).¶
TBA¶