INTERNET-DRAFT D. Eastlake Intended Status: Proposed Standard Futurewei Technologies W. Hao S. Zhuang Z. Li Huawei Technologies R. Gu China Mobil Expires: October 11, 2020 April 12, 2020 BGP Dissemination of Flow Specification Rules for Tunneled Traffic draft-ietf-idr-flowspec-nvo3-09 Abstract This draft specifies a Border Gateway Protocol (BGP) Network Layer Reachability Information (NLRI) encoding format for flow specifications (RFC 5575bis) that can match on a variety of tunneled traffic. In addition, flow specification components are specified for certain tunneling header fields. Status of This Document This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Distribution of this document is unlimited. Comments should be sent to the authors or the IDR Working Group mailing list . Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. D. Eastlake, et al [Page 1] INTERNET-DRAFT BGP Tunnel Flowspec Table of Contents 1. Introduction............................................3 1.1 Terminology............................................3 2. Tunneled Traffic Flow Specification NLRI................5 2.1 The SAFI Code Point....................................7 2.2 Tunnel Header Component Code Points....................8 2.3 Specific Tunnel Types..................................9 2.3.1 VXLAN................................................9 2.3.2 VXLAN-GPE...........................................10 2.3.3 NVGRE...............................................11 2.3.4 L2TPv3..............................................11 2.3.5 GRE.................................................12 2.3.6 IP-in-IP............................................12 2.4 Tunneled Traffic Actions..............................13 3. Order of Traffic Filtering Rules.......................14 4. Flow Spec Validation...................................15 5. Security Considerations................................15 6. IANA Considerations....................................15 Normative References......................................16 Informative References....................................17 Acknowledgments...........................................18 Authors' Addresses........................................18 D. Eastlake, et al [Page 2] INTERNET-DRAFT BGP Tunnel Flowspec 1. Introduction BGP Flow Specification (flowspec [RFC5575bis]) is an extension to BGP that supports the dissemination of traffic flow specification rules. It uses the BGP control plane to simplify the distribution of Access Control Lists (ACLs) and allows new filter rules to be injected to all BGP peers simultaneously without changing router configuration. A typical application of BGP flowspec is to automate the distribution of traffic filter lists to routers for Distributed Denial of Service (DDOS) mitigation. BGP flowspec defines BGP Network Layer Reachability Information (NLRI) formats used to distribute traffic flow specification rules. AFI=1/SAFI=133 is for IPv4 unicast filtering. AFI=1/SAFI=134 is for IPv4 BGP/MPLS VPN filtering. [FlowSpecV6] and [FlowSpecL2] extend the flowspec rules for IPv6 and Layer 2 Ethernet packets respectively. None of these previously defined flow specifications are suitable for matching in cases of tunneling or encapsulation where there might be duplicates of a layer of header such as two IPv6 headers in IP-in-IP or a nested header sequence such as the Layer 2 and 3 headers encapsulated in VXLAN [RFC7348]. In the cloud computing era, multi-tenancy has become a core requirement for data centers. It is increasingly common to see tunneled traffic with a field to distinguish tenants. An example is the Network Virtualization Over Layer 3 (NVO3 [RFC8014]) overlay technology that can satisfy multi-tenancy key requirements. VXLAN [RFC7348] and NVGRE [RFC7637] are two typical NVO3 encapsulations. Other encapsulations such as IP-in-IP or GRE may be encountered. Because these tunnel / overlay technologies involving an additional level of encapsulation, flow specification that can match on the inner header as well as the outer header and fields in any tunneling header are needed. In summary, Flow Specifications should be able to include inner nested header information as well as fields specific to the type of tunneling in use such as virtual network / tenant ID. This draft specifies methods for accomplishing this using SAFI=TBD1 and a new NLRI encoding. 1.1 Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. D. Eastlake, et al [Page 3] INTERNET-DRAFT BGP Tunnel Flowspec The reader is assumed to be familiar with BGP terminology. The following terms and acronyms are used in this document with the meaning indicated: ACL - Access Control List DDoS - Distributed Denial of Service (Attack) DSCP - Differentiated Services Code Point GRE - Generic Router Encapsulation [RFC2890] L2TPv3 - Layer Two Tunneling Protocol - Version 3 [RFC3931] NLRI - Network Layer Reachability Information NVGRE - Network Virtualization Using Generic Routing Encapsulation [RFC7637] NVO3 - Network Virtual Overlay Layer 3 [RFC8014] PE - Provider Edge VN - virtual network VXLAN - Virtual eXtensible Local Area Network [RFC7348] D. Eastlake, et al [Page 4] INTERNET-DRAFT BGP Tunnel Flowspec 2. Tunneled Traffic Flow Specification NLRI The Flowspec rules specified in [RFC5575bis], [FlowSpecV6], and [FlowSpecL2] cannot match or filter tunneled traffic based on the tunnel type, any tunnel header fields, or headers past the tunnel header. To enable flow specification of tunneled traffic, a new SAFI (TBD1) and NLRI encoding are introduced. This encoding, shown in Figure 1, enables flow specification of more than one layer of header when needed. D. Eastlake, et al [Page 5] INTERNET-DRAFT BGP Tunnel Flowspec +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | Length 2 octets | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | Tunnel Type 2 octets | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ Flags: +--+--+--+--+--+--+--+--+ | D| I| Reserved | 1 octet +--+--+--+--+--+--+--+--+ Optional Routing Distinguisher: +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | | + + | | + Routing Distinguisher 8 octets + | | + + | | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ Outer Flowspec: +--+--+--+--+--+--+--+--+ | Outer Flowspec Length : 1 or 2 octets +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | Outer Flowspec variable : +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ Tunnel Header Flowspec: +--+--+--+--+--+--+--+--+ | Tunnel Flowspec Length: 1 or 2 octets +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | Tunnel Header Flowspec variable : +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ Optional Inner Flowspec: +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | Inner AFI 2 octets | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | Inner Flowspec Length : 1 or 2 octets +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | Inner Flowspec variable : +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ Figure 1. Tunneled Traffic Flowspec NLRI Length - The NLRI Length including the Tunnel Type encoded as an unsigned integer. Tunnel Type - The type of tunnel using a value from the IANA BGP Tunnel Encapsulation Attribute Tunnel Types registry. Flags: D bit - Indicates the presence of the Routing Distinguisher (see below). D. Eastlake, et al [Page 6] INTERNET-DRAFT BGP Tunnel Flowspec Flags: I bit - Indicates the presence of the Inner AFI and the Inner Flowspec (see below). Flags: Reserved - Six bits that MUST be sent as zero and ignored on receipt. Routing Distinguisher - If the outer Layer 3 address belongs to a BGP/MPLS VPN, the routing distinguisher is included to indicate traffic filtering within that VPN. Because NVO3 outer layer addresses normally belong to a public network, a Route Distinguisher field is normally not needed for NVO3. Outer Flowspec / Length - The flow specification for the outer header. The length is encoded as provided in Section 4.1 of [RFC5575bis]. The AFI for the Outer Flowspec is the AFI at the beginning of the BGP multiprotocol MP_REACH_NLRI or MP_UNREACH_NLRI containing the tunneled traffic flow specification NLRI. Tunnel Header Flowspec / Length - The flow specification for the tunneling header. This specifies matching criterion on tunnel header fields. The tunnel type itself is indicated by the Tunnel Type field above. For some types of tunneling, such as IP-in-IP, there may be no tunnel header fields. For other types of tunneling, there may be several tunnel header fields on which matching can be specified with this flowspec. Inner AFI - Depending on the Tunnel Type, there may be an Inner AFI that indicates the address family for the inner flow specification. There is no need for a SAFI as the treatment of this inner AFI and following flowspec is indicated by the outer SAFI TBD1, the SAFI for a tunneled traffic flow specification. Inner Flowspec / Length - Depending on the Tunnel Type, there may be an inner flowspec for the header level encapsulated within the outer header. The length is encoded as provided in Section 4.1 of [RFC5575bis]. A Tunneled Traffic Flowspec matches if the Outer Flowspec, Tunnel Header Flowspec, and Inner Flowspec, if present, all match and the Routing Distinguisher applies, if present. An omitted (as can be done for the Inner Flowspec) or null flowspec is considered to always match. 2.1 The SAFI Code Point Use of the tunneled traffic flow specification NLRI format is indicated by SAFI=TBD1. This is used in conjunction with the AFI for D. Eastlake, et al [Page 7] INTERNET-DRAFT BGP Tunnel Flowspec the outer header, that is AFI=1 for IPv4, AFI=2 for IPv6, and AFI=6 for Layer 2. 2.2 Tunnel Header Component Code Points For flowspec based on most tunneling, there are tunnel header fields that can be tested by components that appear in the Tunnel Header Flowspec field. The types for these components are specified in a Tunnel Header Flowspec component registry (see Section 6). All Tunnel Header field components defined below and all such components added in the future have a TLV structure as follows: - one octet of type followed by - one octet giving the length as an unsigned integer number of octets followed by - the specific matching operations/values as determined by the type. Type 1 - VN ID Encoding: . Defines a list of {operation, value} pairs used to match the 24-bit VN ID that is used as the tenant identification in some tunneling headers. For VXLAN encapsulation, the VN ID is the VNI. For NVGRE encapsulation, the VN ID is the VSID. op is encoded as specified in Section 4.2.3 of [RFC5575bis]. Values are encoded as a 1, 2, or 4 octet quantity. If value is 24-bits, it is left-justified in the first 3 octets of the value and the last value octet MUST be sent as zero and ignored on receipt. Type 2 - Flow ID Encoding: Defines a list of {operation, value} pairs used to match 8-bit Flow ID fields which are currently only useful for NVGRE encapsulation. op is encoded as specified in Section 4.2.3 of [RFC5575bis]. Values are encoded as a 1-octet quantity. Type 3 - Session Encoding: Defines a list of {operation, value} pairs used to match a 32-bit Session field. This field is called Key in GRE [RFC2890] encapsulation and Session ID in L2TPv3 encapsulation. op is encoded as specified in Section 4.2.3 of [RFC5575bis]. Values are encoded as a 1, 2, or 4 octet quantity. D. Eastlake, et al [Page 8] INTERNET-DRAFT BGP Tunnel Flowspec Type 4 - Cookie Encoding: Defines a list of {operation, value} pairs used to match a variable length Cookie field. This is only useful in L2TPv3 encapsulation. op is encoded as specified in Section 4.2.3 of [RFC5575bis]. Values are encoded as a 1, 2, 4, or 8 octet quantity. If the Cookie does not fit exactly into the value length, it is left justified, that is, padded with following octets the MUST be sent as zero and ignored on receipt. Type 5 - VXLAN-GPE Flags Encoding: Defines a list of {operation, value} pairs used to match against the VXLAN-GPE flags field. op is encoded as in Section 4.2.9 of [RFC5575bis]. bitmask is encoded as 1 octet. 2.3 Specific Tunnel Types The following subsections describe how to handle flow specification for several specific tunnel types. 2.3.1 VXLAN The headers on a VXLAN [RFC7348] data packet are an outer Ethernet header, an outer IP header, a UDP header, the VXLAN header, and an inner Ethernet header. This inner Ethernet header is frequently, but not always, followed by an inner IP header. If the tunnel type is VXLAN, the I flag MUST be set. If the outer Ethernet header is not being matched, the version (IPv4 or IPv6) of the outer IP header is indicated by the AFI at the beginning of the multiprotocol MP_REACH_NLRI or MP_UNREACH_NLRI containing the tunneled traffic flow specification NLRI. The outer Flowspec is used to filter the outer headers including, if desired, the UDP header. If the outer Ethernet header is being matched, then the initial AFI is 6 [FlowSpecL2] and the Outer Flowspec can match the outer Ethernet header, specify the IP version of the outer IP header, and match that IP header including, if desired, the UDP header. The Tunnel Header Flowspec can be used to filter on the VXLAN header VN ID (VNI). D. Eastlake, et al [Page 9] INTERNET-DRAFT BGP Tunnel Flowspec The Inner Flowspec can be used on the Inner Ethernet header [FlowSpecL2] and any following IP header. If the inner AFI is 6, then the inner Flowspec provides filtering of the Layer 2 header, indicates whether filtering on a following IPv4 or IPv6 header is desired, and if it is desired provides the Flowspec components for that filtering. If the Inner AFI is 1 or 2, the Inner Ethernet header is not matched and to match the Flowspec the Inner Ethernet header must be followed by an IPv4 or IPv6 header, respectively, and the inner Flowspec is used to filter that inner IP header. The inner MAC/IP address is associated with the VN ID. In the NVO3 terminating into a VPN scenario, if multiple access VN IDs map to one VPN instance, one shared VN ID can be carried in the flowspec rule to enforce the rule on the entire VPN instance and the shared VN ID and VPN correspondence should be configured on each VPN PE beforehand. In this case, the function of the Layer 3 VN ID is the same as a Route Distinguisher: it acts as the identification of the VPN instance. 2.3.2 VXLAN-GPE VXLAN-GPE [GPE] is similar to VXLAN. The VXLAN-GPE header is the same size as the VXLAN header but has been extended from the VXLAN header by specifying a number of bits that are reserved in the VXLAN header. In particular, a number of additional flag bits are specified and a Next Protocol field is added that is valid if the P flag bit is set. These flags bits can be tested using the VXLAN-GPE Flags flowspec component defined above. VXLAN and VXLAN-GPE are distinguished by the port number in the UDP header the precedes the VXLAN or VXLAN-GPE headers. If the VXLAN-GPE header P flag is zero, then that header is followed by the same sequence as for VXLAN and the same flowspec choices apply (see Section 2.3.1). If the VXLAN-GPE header P flag is one and that header's next protocol field is 1, then the VXLAN-GPE header is followed by an IPv4 header. The Inner Flowspec matches only if the Inner AFI is 1 and the Inner Flowspec matches. If the VXLAN-GPE header P flag is one and that header's next protocol field is 2, then the VXLAN-GPE header is followed by an IPv6 header. The Inner Flowspec match only if the Inner AFI is 2 and the Inner Flowspec matches. D. Eastlake, et al [Page 10] INTERNET-DRAFT BGP Tunnel Flowspec 2.3.3 NVGRE NVGRE [RFC7637] is very similar to VXLAN except that the UDP header and VXLAN header immediately after the outer IP header are replaced by a GRE (Generic Router Encapsulation) header. The GRE header as used in NVGRE has no Checksum or Reserved1 field as shown in [RFC2890] but there are Virtual Subnet ID and Flow ID fields in place of what is labeled in [RFC2890] as the Key field. Processing and restrictions for NVGRE are as in Section 2.3.1 eliminating references to a UDP header and replacing references to the VXLAN header and its VN ID with references to the GRE header and its VN ID (VSID) and Flow ID. 2.3.4 L2TPv3 The headers on an L2TPv3 [RFC3931] packets are an outer Ethernet header, an outer IP header, the L2TPv3 header, an inner Ethernet header, and possibly an inner IP header if indicated by the inner Ethernet header EtherType. The Outer Flowspec operates on the outer headers that precede the GRE header. The version of IP in the outer IP header is specified by either the outer AFI at the beginning of the MP_REACH_NLRI or MP_UNREACH_NLRI or, if that AFI is 6 (L2), optionally specified by the inner AFI within that L2 flowspec. The L2TPv3 header consists of a 32-bit Session ID followed by a variable length Cookie (maximum length 8 octets). The Session ID and Cookie can be filtered for by using the Session and Cookie flowspec components in the Tunnel Header Flowspec. To filter on Cookie or even be able to bypass Cookie and parse the remainder of the L2TPv3 packet, the node implementing flowspec needs to know the length and/or value of the Cookie fields of interest. This is negotiated at L2TPv3 session establishment and it is out of scope for this document how the node would learn this information. Of course, if flowspec is being used for DDOS mitigation and the Cookie has a fixed length and/or value in the DDOS traffic, this could be learned by inspecting that traffic. If the I flag bit is zero, then no filtering is done on data beyond the L2TPv3 header. If the I flag is one, indicating the presence of an Inner Flowspec, and the node implementing flowspec does not know the length of the L2TPv3 header Cookie, the match fails. If that node does know the length of that Cookie, the Inner Flowspec if matched against the headers at the beginning of that data using the Inner AFI. If that Inner AFI is 1 or 2, then an inner IP header is required and filtering can be done on the Ethernet header immediately after the L2TPv3 header and the following IPv4 or IPv6 headers respectively. If the Inner AFI is 6, filtering is done on the inner Ethernet header and, if a non-zero inner AFI is specified within the D. Eastlake, et al [Page 11] INTERNET-DRAFT BGP Tunnel Flowspec inner L2 flowspec, done on the following IP header [FlowSpecL2]. 2.3.5 GRE Generic Router Encapsulation (GRE [RFC2890]) is another type of encapsulation. The Outer Flowspec operates on the outer headers that precede the GRE header. The version of IP is specified by the outer AFI at the beginning of the MP_REACH_NLRI or MP_UNREACH_NLRI. If the I flag bit is zero, no filtering is done on data after the GRE header. If the I flag bit is one, then there is an inner AFI and flowspec and the Protocol Type field of the GRE header must match the Inner AFI as follows for the Flowspec to match: GRE Protocol Type Inner AFI ------------------- ----------- 0x0800 (IPv4) 1 0x86DD (IPv6) 2 0x6558 6 With the I flag a one and the Inner AFI and GRE Protocol Type fields match, the Inner Flowspec is used to filter the inner IP headers (Inner AFI=1 or 2) or the inner Ethernet header and optionally a following IP header (Inner AFI=6). 2.3.6 IP-in-IP IP-in-IP encapsulation is indicated when an outer IP header indicates an inner IP IPv4 or IPv6 header by the value of the outer IP header's Protocol (IPv4) or Next Protocol (IPv6) field. The IP version of the outer IP header (IPv4 or IPv6) matched is indicated by an AFI of 1 or 2 at the beginning of the MP_REACH_NLRI or MP_UNREACH_NLRI while if that AFI is 6, it indicates a match on the out Ethernet header and, optionally, the following IP Header [FlowSpecL2]. The IP version of the inner IP header is indicated by the Inner AFI and the Inner Flowspec applies to the inner IP header. There are no fields that can be matched by the Tunnel Header Flowspec in the case of IP-in-IP. D. Eastlake, et al [Page 12] INTERNET-DRAFT BGP Tunnel Flowspec 2.4 Tunneled Traffic Actions The traffic filtering actions previously specified in [RFC5575bis] and [FlowSpecL2] are used for tunneled traffic. For Traffic Marking in NVO3, only the DSCP in the outer header can be modified. D. Eastlake, et al [Page 13] INTERNET-DRAFT BGP Tunnel Flowspec 3. Order of Traffic Filtering Rules The following rules determine which flowspec takes precedence where one or more are applicable and at least one of the applicable flowspecs is a tunneled traffic flowspec: - In comparing an applicable tunneled traffic flow specification with an applicable non-tunneled flow specification, the tunneled specification has precedence. - If comparing tunneled traffic flow specifications, if all are applicable, the tunnel types will be the same. Any that have a Routing Distinguisher will take precedence over those without a Routing Distinguisher. Of those with a Routing Distinguisher, all applicable flowspecs will have the same Routing Distinguisher. - At this point in the process, all remaining contenders for the highest precedence will either not have a Routing Distinguisher or have equal Routing Distinguishers. If more than one contender remain, those with an L2 Outer Flowspec take precedence over those with an L3 Outer Flowspec. If the Outer Flowspec AFI is the same, their order of precedence is determined by comparing the Outer Flowspecs as described in [RFC5575bis] and [FlowSpecV6] for AFI for 1 or 2 respectively or [FlowSpecL2] for AFI=6. - If the Outer Flowspecs are equal, then the Tunnel Header Flowspecs are compared using the usual sequential component comparison process [RFC5575bis]. - If the Tunnel Header Flowspecs are equal then compare the "I" flag. Those with an Inner Flowspec take precedence over those without an Inner Flowspec. If you get to this stage in the ordering process, those without an Inner Flowspec are equal. For those with an Inner Flowspec, check the Inner AFI. An L2 Inner AFI (AFI=6) takes precedence over an L2 Inner AFI. - If the Inner AFIs are equal, precedence is determined by comparing the Inner Flowspecs as described in [FlowSpecL2] for L2 or [RFC5575bis] for L3. D. Eastlake, et al [Page 14] INTERNET-DRAFT BGP Tunnel Flowspec 4. Flow Spec Validation Flowspecs received over AFI=1/SAFI=TBD1 or AFI=2/SFAI=TBD1 are validated, using only the Outer Flowspec, against routing reachability received over AFI=1/SAFI=133 and AFI=2/SAFI=133 respectively, as modified by [FlowSpecOID]. 5. Security Considerations No new security issues are introduced to the BGP protocol by this specification. For general Flowspec security considerations, see [rfc5575bis]. 6. IANA Considerations IANA is requested to assign a new SAFI as follows: Value Description Reference ----- ------------------------------------------ --------------- TBD1 Tunneled traffic flow specification rules [This document] IANA is requested to create a Tunnel Header Flow Spec Component Type registry on the Flow Spec Component Types registries web page as follows: Name: Tunnel Flow Spec Component Types Reference: [this document] Registration Procedures: 0 Reserved 1-127 Specification Required 128-254 First Come First Served 255 Reserved Initial contents: Type Name Reference ----- -------------- ----------------- 0 reserved [this document] 1 VN ID [this document] 2 Flow ID [this document] 3 Session [this document] 4 Cookie [this document] 5 VXLAN-GPE Flags [this document] 6-254 unassigned [this document] 255 reserved [this document] D. Eastlake, et al [Page 15] INTERNET-DRAFT BGP Tunnel Flowspec Normative References [RFC2119] - Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC2890] - Dommety, G., "Key and Sequence Number Extensions to GRE", RFC 2890, DOI 10.17487/RFC2890, September 2000, . [RFC3931] - Lau, J., Ed., Townsley, M., Ed., and I. Goyret, Ed., "Layer Two Tunneling Protocol - Version 3 (L2TPv3)", RFC 3931, DOI 10.17487/RFC3931, March 2005, . [RFC7348] - Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger, L., Sridhar, T., Bursell, M., and C. Wright, "Virtual eXtensible Local Area Network (VXLAN): A Framework for Overlaying Virtualized Layer 2 Networks over Layer 3 Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014, . [RFC7637] - Garg, P., Ed., and Y. Wang, Ed., "NVGRE: Network Virtualization Using Generic Routing Encapsulation", RFC 7637, DOI 10.17487/RFC7637, September 2015, . [RFC8174] - Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [FlowSpecL2] - W. Hao, et al, "Dissemination of Flow Specification Rules for L2 VPN", draft-ietf-idr-flowspec-l2vpn, work in progress. [FlowSpecOID] - J. Uttaro, J. Alcaide, C. Filsfils, D. Smith, P. Mohapatra, "Revised Validation Procedure for BGP Flow Specifications", draft-ietf-idr-bgp-flowspec-oid, work in progress. [FlowSpecV6] - R. Raszuk, et al, "Dissemination of Flow Specification Rules for IPv6", draft-ietf-idr-flow-spec-v6, work in progress. [RFC5575bis] - Hares, S., Loibl, C., Raszuk, R., McPherson, D., Bacher, M., "Dissemination of Flow Specification Rules", draft- ietf-idr-rfc5575bis, Work in progress. D. Eastlake, et al [Page 16] INTERNET-DRAFT BGP Tunnel Flowspec Informative References [RFC8014] - Black, D., Hudson, J., Kreeger, L., Lasserre, M., and T. Narten, "An Architecture for Data-Center Network Virtualization over Layer 3 (NVO3)", RFC 8014, DOI 10.17487/RFC8014, December 2016, . [GPE] - P. Quinn, et al, "Generic Protocol Extension for VXLAN", draft-ietf-nvo3-vxlan-gpe, work in progress. D. Eastlake, et al [Page 17] INTERNET-DRAFT BGP Tunnel Flowspec Acknowledgments The authors wish to acknowledge the important contributions of Jeff Haas, Susan Hares, Qiandeng Liang, Nan Wu, Yizhou Li, Robert Raszuk, and Lucy Yong. Authors' Addresses Donald Eastlake Futurewei Technologies 2386 Panoramic Circle Apopka, FL 32703 USA Tel: +1-508-333-2270 Email: d3e3e3@gmail.com Weiguo Hao Huawei Technologies 101 Software Avenue, Nanjing 210012 China Email: haoweiguo@huawei.com Shunwan Zhuang Huawei Technologies Huawei Bld., No.156 Beiqing Rd. Beijing 100095 China Email: zhuangshunwan@huawei.com Zhenbin Li Huawei Technologies Huawei Bld., No.156 Beiqing Rd. Beijing 100095 China Email: lizhenbin@huawei.com Rong Gu China Mobile Email: gurong_cmcc@outlook.com D. Eastlake, et al [Page 18] INTERNET-DRAFT BGP Tunnel Flowspec Copyright, Disclaimer, and Additional IPR Provisions Copyright (c) 2020 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. D. Eastlake, et al [Page 19]