Internet-Draft | NSF Monitoring Interface YANG Data Model | November 2021 |
Jeong, et al. | Expires 21 May 2022 | [Page] |
This document proposes an information model and the corresponding YANG data model of an interface for monitoring Network Security Functions (NSFs) in the Interface to Network Security Functions (I2NSF) framework. If the monitoring of NSFs is performed with the NSF monitoring interface in a comprehensive way, it is possible to detect the indication of malicious activity, anomalous behavior, the potential sign of denial of service attacks, or system overload in a timely manner. This monitoring functionality is based on the monitoring information that is generated by NSFs. Thus, this document describes not only an information model for the NSF monitoring interface along with a YANG data diagram, but also the corresponding YANG data model.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 21 May 2022.¶
Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.¶
According to [RFC8329], the interface provided by a Network Security Function (NSF) (e.g., Firewall, IPS, or Anti-DDoS function) to administrative entities (e.g., Security Controller) to enable remote management (i.e., configuring and monitoring) is referred to as an I2NSF Monitoring Interface. This interface enables the sharing of vital data from the NSFs (e.g., alarms, records, and counters) to the Security Controller through a variety of mechanisms (e.g., queries, notifications, and events). The monitoring of NSF plays an important role in an overall security framework, if it is done in a timely and comprehensive way. The monitoring information generated by an NSF can be a good, early indication of anomalous behavior or malicious activity, such as denial of service attacks (DoS).¶
This document defines a comprehensive information model of an NSF monitoring interface that provides visibility into an NSF for the NSF data collector (e.g., Security Controller). Note that an NSF data collector is defined as an entity to collect NSF monitoring data from an NSF, such as Security Controller. It specifies the information and illustrates the methods that enable an NSF to provide the information required in order to be monitored in a scalable and efficient way via the NSF Monitoring Interface. The information model for the NSF monitoring interface presented in this document is complementary for the security policy provisioning functionality of the NSF-Facing Interface specified in [I-D.ietf-i2nsf-nsf-facing-interface-dm].¶
This document also defines a YANG [RFC7950] data model for the NSF monitoring interface, which is derived from the information model for the NSF monitoring interface.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
This document uses the terminology described in [RFC8329].¶
This document follows the guidelines of [RFC8407], uses the common YANG types defined in [RFC6991], and adopts the Network Management Datastore Architecture (NMDA) [RFC8342]. The meaning of the symbols in tree diagrams is defined in [RFC8340].¶
As mentioned earlier, monitoring plays a critical role in an overall security framework. The monitoring of the NSF provides very valuable information to an NSF data collector (e.g., Security Controller) in maintaining the provisioned security posture. Besides this, there are various other reasons to monitor the NSF as listed below:¶
In order to maintain a strong security posture, it is not only necessary to configure an NSF's security policies but also to continuously monitor the NSF by consuming acquirable and observable data. This enables security administrators to assess the state of the networks and in a timely fashion. It is not possible to block all the internal and external threats based on static security posture. A more practical approach is supported by enabling dynamic security measures, for which continuous visibility is required. This document defines a set of monitoring elements and their scopes that can be acquired from an NSF and can be used as NSF monitoring data. In essence, these types of monitoring data can be leveraged to support constant visibility on multiple levels of granularity and can be consumed by the corresponding functions.¶
Three basic domains about the monitoring data originating from a system entity [RFC4949], i.e., an NSF, are highlighted in this document.¶
As with I2NSF components, every generic system entity can include a set of capabilities that creates information about some context with monitoring data (i.e., monitoring information), composition, configuration, state or behavior of that system entity. This information is intended to be provided to other consumers of information and in the scope of this document, which deals with NSF monitoring data in an automated fashion.¶
A system entity (e.g., NSF) first retains I2NSF monitoring data inside its own system before emitting the information to another I2NSF component (e.g., NSF Data Collector). The I2NSF monitoring information consist of I2NSF Event, I2NSF Record, and I2NSF Counter as follows:¶
The retention of I2NSF monitoring information listed in Section 9 may be affected by the importance of the data. The importance of the data could be context-dependent, where it may not just be based on the type of data, but may also depend on where it is deployed, e.g., a test lab and testbed. The local policy and configuration will dictate the policies and procedures to review, archive, or purge the collected monitoring data.¶
The I2NSF monitoring information retained on a system entity (e.g., NSF) may be delivered to a corresponding I2NSF User via an NSF data collector. The information consists of the aggregated records, typically in the form of log-files or databases. For the NSF Monitoring Interface to deliver the information to the NSF data collector, the NSF needs to accommodate standardized delivery protocols, such as NETCONF [RFC6241] and RESTCONF [RFC8040]. The NSF data collector can forward the information to the I2NSF User through one of standardized delivery protocols. The interface for this delivery is out of the scope of this document.¶
A specific task of I2NSF User is to process I2NSF Policy Rules. The rules of a policy are composed of three clauses: Event, Condition, and Action clauses. In consequence, an I2NSF Event is specified to trigger an I2NSF Policy Rule. Such an I2NSF Event is defined as any important occurrence over time in the system being managed, and/or in the environment of the system being managed, which aligns well with the generic definition of Event from [RFC3877].¶
Another role of the I2NSF Event is to trigger a notification for monitoring the status of an NSF. A notification is defined in [RFC3877] as an unsolicited transmission of management information. System alarm (called alarm) is defined as a warning related to service degradation in system hardware in Section 6.1. System event (called alert) is defined as a warning about any changes of configuration, any access violation, the information of sessions and traffic flows in Section 6.2. Both an alarm and an alert are I2NSF Events that can be delivered as a notification. The model illustrated in this document introduces a complementary type of information that can be a conveyed notification.¶
In I2NSF monitoring, a notification is used to deliver either an event and a record via the I2NSF Monitoring Interface. The difference between the event and record is the timing by which the notifications are emitted. An event is emitted as soon as it happens in order to notify an NSF Data Collector of the problem that needs immediate attention. A record is not emitted immediately to the NSF Data Collector, and it can be emitted periodically to the NSF Data Collector every certain time interval.¶
It is important to note that an NSF Data Collector as a consumer (i.e., observer) of a notification assesses the importance of the notification rather than an NSF as a producer. The producer can include metadata in a notification that supports the observer in assessing its importance (e.g., severity).¶
The freshness of the monitored information depends on the acquisition method. Ideally, an I2NSF User is accessing every relevant information about the I2NSF Component and is emitting I2NSF Events to an NSF data collector (e.g., Security Controller) in a timely manner. Publication of events via a pubsub/broker model, peer-2-peer meshes, or static defined channels are only a few examples on how a solicited push of I2NSF Events can be facilitated. The actual mechanism implemented by an I2NSF Component is out of the scope of this document.¶
Often, the corresponding management interfaces have to be queried in intervals or on demand if required by an I2NSF Policy rule. In some cases, the collection of information has to be conducted via a login mechanism provided by a system entity. Accessing records of information via this kind of unsolicited polls can introduce a significant latency in regard to the freshness of the monitored information. The actual definition of intervals implemented by an I2NSF Component is also out of scope of this document.¶
As explained in the above section, there is a wealth of data available from the NSF that can be monitored. Firstly, there must be some general information with each monitoring message sent from an NSF that helps a consumer to identify meta data with that message, which are listed as below:¶
This section covers the additional information associated with the system messages. The extended information model is only for the structured data such as events, record, and counters. Any unstructured data is specified with the basic information model only.¶
Each information has characteristics as follows:¶
System alarms have the following characteristics:¶
The memory is the hardware to store information temporarily or for a short period, i.e., Random Access Memory (RAM). The memory-alarm is emitted when the RAM usage exceeds the threshold. The following information should be included in a Memory Alarm:¶
CPU is the Central Processing Unit that executes basic operations of the system. The cpu-alarm is emitted when the CPU usage exceeds the threshold. The following information should be included in a CPU Alarm:¶
Disk is the hardware to store information for a long period, i.e., Hard Disk or Solid-State Drive. The disk-alarm is emitted when the Disk usage exceeds the threshold. The following information should be included in a Disk Alarm:¶
The hardware-alarm is emitted when a hardware, e.g., CPU, memory, disk, or interface, problem is detected. The following information should be included in a Hardware Alarm:¶
Interface is the network interface for connecting a device with the network. The interface-alarm is emitted when the state of the interface is changed. The following information should be included in an Interface Alarm:¶
System events (as alerts) have the following characteristics:¶
The access-violation system event is an event when a user tries to access (read, write, create, or delete) any information or execute commands above their privilege.¶
A configuration change is a system event when a new configuration is added or an existing configuration is modified. The following information should be included in this event:¶
The following information should be included in a Session Table Event:¶
Traffic flows need to be monitored because they might be used for security attacks to the network. The following information should be included in this event:¶
NSF events have the following characteristics:¶
The following information should be included in a DDoS Event:¶
The following information should be included in a Virus Event:¶
The following information should be included in an Intrusion Event:¶
The following information should be included in a Web Attack Alarm:¶
The following information should be included in a VoIP/VoLTE Event:¶
System log is a record that is used to monitor the activity of the user on the NSF and the status of the NSF. System logs have the following characteristics:¶
Access logs record administrators' login, logout, and operations on a device. By analyzing them, security vulnerabilities can be identified. The following information should be included in an operation report:¶
Running reports record the device system's running status, which is useful for device monitoring. The following information should be included in running report:¶
User activity logs provide visibility into users' online records (such as login time, online/lockout duration, and login IP addresses) and the actions that users perform. User activity reports are helpful to identify exceptions during a user's login and network access activities.¶
additional-info: Additional Information for login:¶
NSF logs have the folowing characteristics:¶
Deep Packet Inspection (DPI) Logs provide statistics on uploaded and downloaded files and data, sent and received emails, and alert and blocking records on websites. It is helpful to learn risky user behaviors and why access to some URLs is blocked or allowed with an alert record.¶
System counter has the following characteristics:¶
Interface counters provide visibility into traffic into and out of an NSF, and bandwidth usage. The statistics of the interface counters should be computed from the start of the service. When the service is reset, the computation of statistics per counter should restart from 0.¶
NSF counters have the following characteristics:¶
Firewall counters provide visibility into traffic signatures, bandwidth usage, and how the configured security and bandwidth policies have been applied.¶
Policy Hit Counters record the security policy that traffic matches and its hit count. It can check if policy configurations are correct.¶
A standard model for monitoring data is required for an administrator to check the monitoring data generated by an NSF. The administrator can check the monitoring data through the following process. When the NSF monitoring data that is under the standard format is generated, the NSF forwards it to an NSF data collector via the I2NSF NSF Monitoring Interface. The NSF data collector delivers it to I2NSF Consumer or Developer's Management System (DMS) so that the administrator can know the state of the I2NSF framework.¶
In order to communicate with other components, an I2NSF framework [RFC8329] requires the interfaces. The three main interfaces in I2NSF framework are used for sending monitoring data as follows:¶
The tree structure of the NSF monitoring YANG module is provided below:¶
module: ietf-i2nsf-nsf-monitoring +--ro i2nsf-counters | +--ro system-interface* [interface-name] | | +--ro acquisition-method? identityref | | +--ro emission-type? identityref | | +--ro dampening-type? identityref | | +--ro interface-name if:interface-ref | | +--ro in-total-traffic-pkts? yang:counter32 | | +--ro out-total-traffic-pkts? yang:counter32 | | +--ro in-total-traffic-bytes? uint64 | | +--ro out-total-traffic-bytes? uint64 | | +--ro in-drop-traffic-pkts? yang:counter32 | | +--ro out-drop-traffic-pkts? yang:counter32 | | +--ro in-drop-traffic-bytes? uint64 | | +--ro out-drop-traffic-bytes? uint64 | | +--ro discontinuity-time yang:date-and-time | | +--ro total-traffic? yang:counter32 | | +--ro in-traffic-average-rate? uint32 | | +--ro in-traffic-peak-rate? uint32 | | +--ro in-traffic-average-speed? uint64 | | +--ro in-traffic-peak-speed? uint64 | | +--ro out-traffic-average-rate? uint32 | | +--ro out-traffic-peak-rate? uint32 | | +--ro out-traffic-average-speed? uint64 | | +--ro out-traffic-peak-speed? uint64 | | +--ro message? string | | +--ro vendor-name? string | | +--ro nsf-name? union | | +--ro severity? severity | | +--ro timestamp? yang:date-and-time | +--ro nsf-firewall* [policy-name] | | +--ro acquisition-method? identityref | | +--ro emission-type? identityref | | +--ro dampening-type? identityref | | +--ro policy-name -> /nsfintf:i2nsf-security-policy/system-policy-name | | +--ro src-user? string | | +--ro discontinuity-time yang:date-and-time | | +--ro total-traffic? yang:counter32 | | +--ro in-traffic-average-rate? uint32 | | +--ro in-traffic-peak-rate? uint32 | | +--ro in-traffic-average-speed? uint64 | | +--ro in-traffic-peak-speed? uint64 | | +--ro out-traffic-average-rate? uint32 | | +--ro out-traffic-peak-rate? uint32 | | +--ro out-traffic-average-speed? uint64 | | +--ro out-traffic-peak-speed? uint64 | | +--ro message? string | | +--ro vendor-name? string | | +--ro nsf-name? union | | +--ro severity? severity | | +--ro timestamp? yang:date-and-time | +--ro nsf-policy-hits* [policy-name] | +--ro acquisition-method? identityref | +--ro emission-type? identityref | +--ro dampening-type? identityref | +--ro policy-name -> /nsfintf:i2nsf-security-policy/system-policy-name | +--ro src-user? string | +--ro message? string | +--ro vendor-name? string | +--ro nsf-name? union | +--ro severity? severity | +--ro discontinuity-time yang:date-and-time | +--ro hit-times? yang:counter32 | +--ro timestamp? yang:date-and-time +--rw i2nsf-monitoring-configuration +--rw i2nsf-system-detection-alarm | +--rw enabled? boolean | +--rw system-alarm* [alarm-type] | +--rw alarm-type enumeration | +--rw threshold? uint8 | +--rw dampening-period? uint32 +--rw i2nsf-system-detection-event | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-traffic-flows | +--rw dampening-period? uint32 | +--rw enabled? boolean +--rw i2nsf-nsf-detection-ddos {i2nsf-nsf-detection-ddos}? | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-nsf-detection-session-table-configuration | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-nsf-detection-intrusion {i2nsf-nsf-detection-intrusion}? | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-nsf-detection-web-attack {i2nsf-nsf-detection-web-attack}? | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-nsf-system-access-log | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-system-res-util-log | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-system-user-activity-log | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-nsf-log-dpi {i2nsf-nsf-log-dpi}? | +--rw enabled? boolean | +--rw dampening-period? uint32 +--rw i2nsf-counter +--rw period? uint16 notifications: +---n i2nsf-event | +--ro (sub-event-type)? | +--:(i2nsf-system-detection-alarm) | | +--ro i2nsf-system-detection-alarm | | +--ro alarm-category? identityref | | +--ro component-name? string | | +--ro interface-name? if:interface-ref | | +--ro interface-state? enumeration | | +--ro acquisition-method? identityref | | +--ro emission-type? identityref | | +--ro dampening-type? identityref | | +--ro usage? uint8 | | +--ro threshold? uint8 | | +--ro message? string | | +--ro vendor-name? string | | +--ro nsf-name? union | | +--ro severity? severity | +--:(i2nsf-system-detection-event) | | +--ro i2nsf-system-detection-event | | +--ro event-category? identityref | | +--ro acquisition-method? identityref | | +--ro emission-type? identityref | | +--ro dampening-type? identityref | | +--ro user string | | +--ro group* string | | +--ro ip-address inet:ip-address-no-zone | | +--ro authentication? identityref | | +--ro message? string | | +--ro vendor-name? string | | +--ro nsf-name? union | | +--ro severity? severity | +--:(i2nsf-traffic-flows) | | +--ro i2nsf-traffic-flows | | +--ro src-ip? inet:ip-address-no-zone | | +--ro dst-ip? inet:ip-address-no-zone | | +--ro protocol? identityref | | +--ro src-port? inet:port-number | | +--ro dst-port? inet:port-number | | +--ro arrival-rate? uint32 | | +--ro acquisition-method? identityref | | +--ro emission-type? identityref | | +--ro dampening-type? identityref | | +--ro message? string | | +--ro vendor-name? string | | +--ro nsf-name? union | | +--ro severity? severity | +--:(i2nsf-nsf-detection-session-table) | +--ro i2nsf-nsf-detection-session-table | +--ro current-session? uint32 | +--ro maximum-session? uint32 | +--ro threshold? uint32 | +--ro message? string | +--ro vendor-name? string | +--ro nsf-name? union | +--ro severity? severity +---n i2nsf-log | +--ro (sub-logs-type)? | +--:(i2nsf-nsf-system-access-log) | | +--ro i2nsf-nsf-system-access-log | | +--ro login-ip? inet:ip-address-no-zone | | +--ro username? string | | +--ro login-role? login-role | | +--ro operation-type? operation-type | | +--ro input? string | | +--ro output? string | | +--ro acquisition-method? identityref | | +--ro emission-type? identityref | | +--ro dampening-type? identityref | | +--ro message? string | | +--ro vendor-name? string | | +--ro nsf-name? union | | +--ro severity? severity | +--:(i2nsf-system-res-util-log) | | +--ro i2nsf-system-res-util-log | | +--ro system-status? enumeration | | +--ro cpu-usage? uint8 | | +--ro memory-usage? uint8 | | +--ro disk* [disk-id] | | | +--ro disk-id string | | | +--ro disk-usage? uint8 | | | +--ro disk-left? uint8 | | +--ro session-num? uint32 | | +--ro process-num? uint32 | | +--ro interface* [interface-id] | | | +--ro interface-id string | | | +--ro in-traffic-rate? uint32 | | | +--ro out-traffic-rate? uint32 | | | +--ro in-traffic-speed? uint64 | | | +--ro out-traffic-speed? uint64 | | +--ro acquisition-method? identityref | | +--ro emission-type? identityref | | +--ro dampening-type? identityref | | +--ro message? string | | +--ro vendor-name? string | | +--ro nsf-name? union | | +--ro severity? severity | +--:(i2nsf-system-user-activity-log) | +--ro i2nsf-system-user-activity-log | +--ro acquisition-method? identityref | +--ro emission-type? identityref | +--ro dampening-type? identityref | +--ro user string | +--ro group* string | +--ro ip-address inet:ip-address-no-zone | +--ro authentication? identityref | +--ro message? string | +--ro vendor-name? string | +--ro nsf-name? union | +--ro severity? severity | +--ro online-duration? uint32 | +--ro logout-duration? uint32 | +--ro additional-info? enumeration +---n i2nsf-nsf-event +--ro (sub-event-type)? +--:(i2nsf-nsf-detection-ddos) {i2nsf-nsf-detection-ddos}? | +--ro i2nsf-nsf-detection-ddos | +--ro attack-type? identityref | +--ro start-time yang:date-and-time | +--ro end-time yang:date-and-time | +--ro attack-src-ip* inet:ip-address-no-zone | +--ro attack-dst-ip* inet:ip-address-no-zone | +--ro attack-src-port* inet:port-number | +--ro attack-dst-port* inet:port-number | +--ro rule-name -> /nsfintf:i2nsf-security-policy/rules/rule-name | +--ro raw-info? string | +--ro attack-rate? uint32 | +--ro attack-speed? uint64 | +--ro action* log-action | +--ro acquisition-method? identityref | +--ro emission-type? identityref | +--ro dampening-type? identityref | +--ro message? string | +--ro vendor-name? string | +--ro nsf-name? union | +--ro severity? severity +--:(i2nsf-nsf-detection-virus) {i2nsf-nsf-detection-virus}? | +--ro i2nsf-nsf-detection-virus | +--ro dst-ip? inet:ip-address-no-zone | +--ro dst-port? inet:port-number | +--ro rule-name -> /nsfintf:i2nsf-security-policy/rules/rule-name | +--ro raw-info? string | +--ro src-ip? inet:ip-address-no-zone | +--ro src-port? inet:port-number | +--ro src-location? string | +--ro dst-location? string | +--ro virus? identityref | +--ro virus-name? string | +--ro file-type? string | +--ro file-name? string | +--ro os? string | +--ro action* log-action | +--ro acquisition-method? identityref | +--ro emission-type? identityref | +--ro dampening-type? identityref | +--ro message? string | +--ro vendor-name? string | +--ro nsf-name? union | +--ro severity? severity +--:(i2nsf-nsf-detection-intrusion) {i2nsf-nsf-detection-intrusion}? | +--ro i2nsf-nsf-detection-intrusion | +--ro dst-ip? inet:ip-address-no-zone | +--ro dst-port? inet:port-number | +--ro rule-name -> /nsfintf:i2nsf-security-policy/rules/rule-name | +--ro raw-info? string | +--ro src-ip? inet:ip-address-no-zone | +--ro src-port? inet:port-number | +--ro src-location? string | +--ro dst-location? string | +--ro protocol? identityref | +--ro app? identityref | +--ro attack-type? identityref | +--ro action* log-action | +--ro attack-rate? uint32 | +--ro attack-speed? uint64 | +--ro acquisition-method? identityref | +--ro emission-type? identityref | +--ro dampening-type? identityref | +--ro message? string | +--ro vendor-name? string | +--ro nsf-name? union | +--ro severity? severity +--:(i2nsf-nsf-detection-web-attack) {i2nsf-nsf-detection-web-attack}? | +--ro i2nsf-nsf-detection-web-attack | +--ro dst-ip? inet:ip-address-no-zone | +--ro dst-port? inet:port-number | +--ro rule-name -> /nsfintf:i2nsf-security-policy/rules/rule-name | +--ro raw-info? string | +--ro src-ip? inet:ip-address-no-zone | +--ro src-port? inet:port-number | +--ro src-location? string | +--ro dst-location? string | +--ro attack-type? identityref | +--ro req-method? identityref | +--ro req-target? string | +--ro filtering-type* identityref | +--ro req-user-agent? string | +--ro cookies? string | +--ro req-host? string | +--ro response-code? string | +--ro acquisition-method? identityref | +--ro emission-type? identityref | +--ro dampening-type? identityref | +--ro action* log-action | +--ro message? string | +--ro vendor-name? string | +--ro nsf-name? union | +--ro severity? severity +--:(i2nsf-nsf-detection-voip-volte) {i2nsf-nsf-detection-voip-volte}? | +--ro i2nsf-nsf-detection-voip-volte | +--ro dst-ip? inet:ip-address-no-zone | +--ro dst-port? inet:port-number | +--ro rule-name -> /nsfintf:i2nsf-security-policy/rules/rule-name | +--ro raw-info? string | +--ro src-ip? inet:ip-address-no-zone | +--ro src-port? inet:port-number | +--ro src-location? string | +--ro dst-location? string | +--ro source-voice-id* string | +--ro destination-voice-id* string | +--ro user-agent* string +--:(i2nsf-nsf-log-dpi) {i2nsf-nsf-log-dpi}? +--ro i2nsf-nsf-log-dpi +--ro attack-type? dpi-type +--ro acquisition-method? identityref +--ro emission-type? identityref +--ro dampening-type? identityref +--ro policy-name -> /nsfintf:i2nsf-security-policy/system-policy-name +--ro src-user? string +--ro message? string +--ro vendor-name? string +--ro nsf-name? union +--ro severity? severity
This section describes a YANG module of I2NSF NSF Monitoring. The data model provided in this document uses identities to be used to get information of the monitored of an NSF's monitoring data. Every identity used in the document gives information or status about the current situation of an NSF. This YANG module imports from [RFC6991], and makes references to [RFC0768][RFC0791] [RFC0792][RFC0793][RFC0854] [RFC1939][RFC0959][RFC4340] [RFC4443][RFC4960][RFC5321] [RFC6242][RFC6265][RFC7230] [RFC7231][RFC8200][RFC8641] [RFC9051] [I-D.ietf-tcpm-rfc793bis] [IANA-HTTP-Status-Code] [IANA-Media-Types].¶
<CODE BEGINS> file "ietf-i2nsf-nsf-monitoring@2021-11-17.yang" module ietf-i2nsf-nsf-monitoring { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-i2nsf-nsf-monitoring"; prefix nsfmi; import ietf-inet-types{ prefix inet; reference "Section 4 of RFC 6991"; } import ietf-yang-types { prefix yang; reference "Section 3 of RFC 6991"; } import ietf-i2nsf-policy-rule-for-nsf { prefix nsfintf; reference "Section 4.1 of draft-ietf-i2nsf-nsf-facing-interface-dm-14"; } import ietf-interfaces { prefix if; reference "Section 5 of RFC 8343"; } organization "IETF I2NSF (Interface to Network Security Functions) Working Group"; contact "WG Web: <https://tools.ietf.org/wg/i2nsf> WG List: <mailto:i2nsf@ietf.org> Editor: Jaehoon Paul Jeong <mailto:pauljeong@skku.edu> Editor: Patrick Lingga <mailto:patricklink@skku.edu>"; description "This module is a YANG module for I2NSF NSF Monitoring. The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED', 'MAY', and 'OPTIONAL' in this document are to be interpreted as described in BCP 14 (RFC 2119) (RFC 8174) when, and only when, they appear in all capitals, as shown here. Copyright (c) 2021 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX (https://www.rfc-editor.org/info/rfcXXXX); see the RFC itself for full legal notices."; revision "2021-11-17" { description "Latest revision"; reference "RFC XXXX: I2NSF NSF Monitoring Interface YANG Data Model"; // RFC Ed.: replace XXXX with an actual RFC number and remove // this note. } /* * Typedefs */ typedef severity { type enumeration { enum critical { description "The 'critical' severity level indicates that an immediate corrective action is required. A 'critical' severity is reported when a service becomes totally out of service and must be restored."; } enum high { description "The 'high' severity level indicates that an urgent corrective action is required. A 'high' severity is reported when there is a severe degradation in the capability of the service and its full capability must be restored."; } enum middle { description "The 'middle' severity level indicates the existence of a non-service-affecting fault condition and corrective action should be done to prevent a more serious fault. The 'middle' severity is reported when the detected problem is not degrading the capability of the service, but some service degradation might happen if not prevented."; } enum low { description "The 'low' severity level indicates the detection of a potential fault before any effect is observed. The 'low' severity is reported when an action should be done before a fault happen."; } } description "An indicator representing severity levels. The severity levels starting from the highest are critical, high, middle, and low."; } typedef log-action { type enumeration { enum allow { description "If action is allowed"; } enum alert { description "If action is alert"; } enum block { description "If action is block"; } enum discard { description "If action is discarded"; } enum declare { description "If action is declared"; } enum block-ip { description "If action is block-ip"; } enum block-service{ description "If action is block-service"; } } description "The type representing action for logging."; } typedef dpi-type{ type enumeration { enum file-blocking{ description "DPI for preventing the specified file types from flowing in the network."; } enum data-filtering{ description "DPI for preventing sensitive information (e.g., Credit Card Number or Social Security Numbers) leaving a protected network."; } enum application-behavior-control{ description "DPI for filtering packet based on the application or network behavior analysis to identify malicious or unusual activity."; } } description "The type of Deep Packet Inspection (DPI). The defined types are file-blocking, data-filtering, and application-behavior-control."; } typedef operation-type{ type enumeration { enum login { description "The operation type is Login."; } enum logout { description "The operation type is Logout."; } enum configuration { description "The operation type is Configuration. The configuration operation includes the command for writing a new configuration and modifying an existing configuration."; } enum other { description "The operation type is Other operation. This other includes all operations done by a user except login, logout, and configuration."; } } description "The type of operation done by a user during a session. The user operation is not considering their privileges."; } typedef login-role { type enumeration { enum administrator { description "Administrator (i.e., Superuser)'s login role. Non-restricted role."; } enum user { description "User login role. Semi-restricted role, some data and configurations are available but confidential or important data and configuration are restricted."; } enum guest { description "Guest login role. Restricted role, only few read data are available and write configurations are restricted."; } } description "The privilege level of the user account."; } /* * Identity */ identity characteristics { description "Base identity for monitoring information characteristics"; } identity acquisition-method { base characteristics; description "The type of acquisition-method. It can be multiple types at once."; } identity subscription { base acquisition-method; description "The acquisition-method type is subscription."; } identity query { base acquisition-method; description "The acquisition-method type is query."; } identity emission-type { base characteristics; description "The type of emission-type."; } identity periodic { base emission-type; description "The emission-type type is periodic."; } identity on-change { base emission-type; description "The emission-type type is on-change."; } identity dampening-type { base characteristics; description "The type of message dampening to stop the rapid transmission of messages. The dampening types are on-repetition and no-dampening"; } identity no-dampening { base dampening-type; description "The dampening-type is no-dampening. No-dampening type does not limit the transmission for the messages of the same type."; } identity on-repetition { base dampening-type; description "The dampening-type is on-repetition. On-repetition type limits the transmitted on-change message to one message at a certain interval."; } identity authentication-mode { description "The authentication mode for a user to connect to the NSF, e.g., pre-configured-key and certificate-authority"; } identity pre-configured-key { base authentication-mode; description "The pre-configured-key is an authentication using a key authentication."; } identity certificate-authority { base authentication-mode; description "The certificate-authority (CA) is an authentication using a digital certificate."; } identity event { description "Base identity for I2NSF events."; } identity system-event { base event; description "Identity for system event"; } identity system-alarm { base event; description "Base identity for detectable system alarm types"; } identity memory-alarm { base system-alarm; description "A memory alarm is alerted."; } identity cpu-alarm { base system-alarm; description "A CPU alarm is alerted."; } identity disk-alarm { base system-alarm; description "A disk alarm is alerted."; } identity hardware-alarm { base system-alarm; description "A hardware alarm (i.e., hardware failure) is alerted."; } identity interface-alarm { base system-alarm; description "An interface alarm is alerted."; } identity access-violation { base system-event; description "The access-violation system event is an event when a user tries to access (read, write, create, or delete) any information or execute commands above their privilege."; } identity configuration-change { base system-event; description "The configuration-change system event is an event when a user adds a new configuration or modify an existing configuration (write configuration)."; } identity attack-type { description "The root ID of attack-based notification in the notification taxonomy"; } identity nsf-attack-type { base attack-type; description "This ID is intended to be used in the context of NSF event."; } identity virus-type { base nsf-attack-type; description "The type of virus. It can be multiple types at once. This attack type is associated with a detected system-log virus-attack."; } identity trojan { base virus-type; description "The virus type is a trojan. Trojan is able to disguise the intent of the files or programs to misleads the users."; } identity worm { base virus-type; description "The virus type is a worm. Worm can self-replicate and spread through the network automatically."; } identity macro { base virus-type; description "The virus type is a macro virus. Macro causes a series of threats automatically after the program is executed."; } identity boot-sector { base virus-type; description "The virus type is a boot sector virus. Boot sector is a virus that infects the core of the computer, affecting the startup process."; } identity polymorphic { base virus-type; description "The virus type is a polymorphic virus. Polymorphic can modify its version when it replicates, making it hard to detect."; } identity overwrite { base virus-type; description "The virus type is an overwrite virus. Overwrite can remove existing software and replace it with malicious code by overwriting it."; } identity resident { base virus-type; description "The virus-type is a resident virus. Resident saves itself in the computer's memory and infects other files and software."; } identity non-resident { base virus-type; description "The virus-type is a non-resident virus. Non-resident attaches directly to an executable file and enters the device when executed."; } identity multipartite { base virus-type; description "The virus-type is a multipartite virus. Multipartite attacks both the boot sector and executables files of a computer."; } identity spacefiller { base virus-type; description "The virus-type is a spacefiller virus. Spacefiller fills empty spaces of a file or software with malicious code."; } identity intrusion-attack-type { base nsf-attack-type; description "The attack type is associated with a detected system-log intrusion."; } identity brute-force { base intrusion-attack-type; description "The intrusion type is brute-force."; } identity buffer-overflow { base intrusion-attack-type; description "The intrusion type is buffer-overflow."; } identity web-attack-type { base nsf-attack-type; description "The attack type is associated with a detected system-log web-attack."; } identity command-injection { base web-attack-type; description "The detected web attack type is command injection."; } identity xss { base web-attack-type; description "The detected web attack type is XSS."; } identity csrf { base web-attack-type; description "The detected web attack type is CSRF."; } identity ddos-type { base nsf-attack-type; description "Base identity for detectable flood types"; } identity syn-flood { base ddos-type; description "A SYN flood is detected."; } identity ack-flood { base ddos-type; description "An ACK flood is detected."; } identity syn-ack-flood { base ddos-type; description "A SYN-ACK flood is detected."; } identity fin-rst-flood { base ddos-type; description "A FIN-RST flood is detected."; } identity tcp-con-flood { base ddos-type; description "A TCP connection flood is detected."; } identity udp-flood { base ddos-type; description "A UDP flood is detected."; } identity icmpv4-flood { base ddos-type; description "An ICMPv4 flood is detected."; } identity icmpv6-flood { base ddos-type; description "An ICMPv6 flood is detected."; } identity http-flood { base ddos-type; description "An HTTP flood is detected."; } identity https-flood { base ddos-type; description "An HTTPS flood is detected."; } identity dns-query-flood { base ddos-type; description "A Domain Name System (DNS) query flood is detected."; } identity dns-reply-flood { base ddos-type; description "A Domain Name System (DNS) reply flood is detected."; } identity sip-flood { base ddos-type; description "A Session Initiation Protocol (SIP) flood is detected."; } identity ssl-flood { base ddos-type; description "An Secure Sockets Layer (SSL) flood is detected"; } identity ntp-amp-flood { base ddos-type; description "A Network Time Protocol (NTP) amplification is detected"; } identity req-method { description "A set of request types in HTTP (if applicable)."; } identity put { base req-method; description "The detected request type is PUT."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method PUT"; } identity post { base req-method; description "The detected request type is POST."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method POST"; } identity get { base req-method; description "The detected request type is GET."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method GET"; } identity head { base req-method; description "The detected request type is HEAD."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method HEAD"; } identity delete { base req-method; description "The detected request type is DELETE."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method DELETE"; } identity connect { base req-method; description "The detected request type is CONNECT."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method CONNECT"; } identity options { base req-method; description "The detected request type is OPTIONS."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method OPTIONS"; } identity trace { base req-method; description "The detected request type is TRACE."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Method TRACE"; } identity filter-type { description "The type of filter used to detect an attack, for example, a web-attack. It can be applicable to more than web-attacks."; } identity allow-list { base filter-type; description "The applied filter type is an allow list. This filter blocks all connection except the specified list."; } identity deny-list { base filter-type; description "The applied filter type is a deny list. This filter opens all connection except the specified list."; } identity unknown-filter { base filter-type; description "The applied filter is unknown."; } identity protocol { description "An identity used to enable type choices in leaves and leaflists with respect to protocol metadata. This is used to identify the type of protocol that goes through the NSF."; } identity ip { base protocol; description "General IP protocol type."; reference "RFC 791: Internet Protocol RFC 8200: Internet Protocol, Version 6 (IPv6)"; } identity ipv4 { base ip; description "IPv4 protocol type."; reference "RFC 791: Internet Protocol"; } identity ipv6 { base ip; description "IPv6 protocol type."; reference "RFC 8200: Internet Protocol, Version 6 (IPv6)"; } identity icmp { base protocol; description "Base identity for ICMPv4 and ICMPv6 condition capability"; reference "RFC 792: Internet Control Message Protocol RFC 4443: Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification - ICMPv6"; } identity icmpv4 { base icmp; description "ICMPv4 protocol type."; reference "RFC 791: Internet Protocol RFC 792: Internet Control Message Protocol"; } identity icmpv6 { base icmp; description "ICMPv6 protocol type."; reference "RFC 8200: Internet Protocol, Version 6 (IPv6) RFC 4443: Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification"; } identity transport-protocol { base protocol; description "Base identity for Layer 4 protocol condition capabilities, e.g., TCP, UDP, SCTP, DCCP, and ICMP"; } identity tcp { base transport-protocol; description "TCP protocol type."; reference "RFC 793: Transmission Control Protocol draft-ietf-tcpm-rfc793bis-25: Transmission Control Protocol (TCP) Specification"; } identity udp { base transport-protocol; description "UDP protocol type."; reference "RFC 768: User Datagram Protocol"; } identity sctp { base transport-protocol; description "Identity for SCTP condition capabilities"; reference "RFC 4960: Stream Control Transmission Protocol"; } identity dccp { base transport-protocol; description "Identity for DCCP condition capabilities"; reference "RFC 4340: Datagram Congestion Control Protocol"; } identity application-protocol { base protocol; description "Base identity for Application protocol, e.g., HTTP, FTP"; } identity http { base application-protocol; description "HTTP protocol type."; reference "RFC7230: Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing RFC7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content"; } identity https { base application-protocol; description "HTTPS protocol type."; reference "RFC7230: Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing RFC7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content"; } identity ftp { base application-protocol; description "FTP protocol type."; reference "RFC 959: File Transfer Protocol"; } identity ssh { base application-protocol; description "SSH protocol type."; reference "RFC 6242: Using the NETCONF Protocol over Secure Shell (SSH)"; } identity telnet { base application-protocol; description "The identity for telnet."; reference "RFC 854: Telnet Protocol"; } identity smtp { base application-protocol; description "The identity for smtp."; reference "RFC 5321: Simple Mail Transfer Protocol (SMTP)"; } identity pop3 { base application-protocol; description "The identity for pop3."; reference "RFC 1939: Post Office Protocol - Version 3 (POP3)"; } identity imap { base application-protocol; description "The identity for Internet Message Access Protocol."; reference "RFC 9051: Internet Message Access Protocol (IMAP) - Version 4rev2"; } /* * Grouping */ grouping timestamp { description "Grouping for identifying the time of the message."; leaf timestamp { type yang:date-and-time; description "Specify the time of a message being delivered."; } } grouping common-monitoring-data { description "A set of common monitoring data that is needed as the basic information."; leaf message { type string; description "This is a freetext annotation for monitoring a notification's content."; } leaf vendor-name { type string; description "The name of the NSF vendor. The string is unrestricted to identify the provider or vendor of the NSF."; } leaf nsf-name { type union { type string; type inet:ip-address-no-zone; } description "The name or IP address of the NSF generating the message. If the given nsf-name is not IP address, the name can be an arbitrary string including FQDN (Fully Qualified Domain Name). The name MUST be unique in the scope of management domain for a different NSF to identify the NSF that generates the message."; } leaf severity { type severity; description "The severity of the alarm such as critical, high, middle, and low."; } } grouping characteristics { description "A set of characteristics of a notification."; leaf acquisition-method { type identityref { base acquisition-method; } description "The acquisition-method for characteristics"; } leaf emission-type { type identityref { base emission-type; } description "The emission-type for characteristics"; } leaf dampening-type { type identityref { base dampening-type; } description "The dampening-type for characteristics"; } } grouping i2nsf-system-alarm-type-content { description "A set of contents for alarm type notification."; leaf usage { type uint8 { range "0..100"; } units "percent"; description "Specifies the used percentage"; } leaf threshold { type uint8 { range "0..100"; } units "percent"; description "The threshold percentage triggering the alarm or the event"; } } grouping i2nsf-system-event-type-content { description "System event metadata associated with system events caused by user activity."; leaf user { type string; mandatory true; description "The name of a user"; } leaf-list group { type string; description "The group(s) to which a user belongs."; } leaf ip-address { type inet:ip-address-no-zone; mandatory true; description "The IPv4 (or IPv6) address of a user that trigger the event."; } leaf authentication { type identityref { base authentication-mode; } description "The authentication-mode of a user."; } } grouping i2nsf-nsf-event-type-content { description "A set of common IPv4 (or IPv6)-related NSF event content elements"; leaf dst-ip { type inet:ip-address-no-zone; description "The destination IPv4 (IPv6) address of the packet"; } leaf dst-port { type inet:port-number; description "The destination port of the packet"; } leaf rule-name { type leafref { path "/nsfintf:i2nsf-security-policy" +"/nsfintf:rules/nsfintf:rule-name"; } mandatory true; description "The name of the I2NSF Policy Rule being triggered"; } leaf raw-info { type string; description "The information describing the packet triggering the event."; } } grouping i2nsf-nsf-event-type-content-extend { description "A set of extended common IPv4 (or IPv6)-related NSF event content elements"; uses i2nsf-nsf-event-type-content; leaf src-ip { type inet:ip-address-no-zone; description "The source IPv4 (or IPv6) address of the packet or flow"; } leaf src-port { type inet:port-number; description "The source port of the packet or flow"; } leaf src-location { type string { length "1..100"; pattern "[0-9a-zA-Z ]*"; } description "The source geographical location (e.g., country and city) of the src-ip field."; } leaf dst-location { type string { length "1..100"; pattern "[0-9a-zA-Z ]*"; } description "The destination geographical location (e.g., country and city) of the dst-ip field."; } } grouping log-action { description "A grouping for logging action."; leaf-list action { type log-action; description "Action type: allow, alert, block, discard, declare, block-ip, block-service"; } } grouping attack-rates { description "A set of traffic rates for monitoring attack traffic data"; leaf attack-rate { type uint32; units "pps"; description "The average packets per second (pps) rate of attack traffic"; } leaf attack-speed { type uint64; units "Bps"; description "The average bytes per second (Bps) speed of attack traffic"; } } grouping traffic-rates { description "A set of traffic rates for statistics data"; leaf discontinuity-time { type yang:date-and-time; mandatory true; description "The time on the most recent occasion at which any one or more of this interface's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this node contains the time the local management subsystem re-initialized itself."; } leaf total-traffic { type yang:counter32; units "packets"; description "The total number of traffic packets (in and out) in the NSF."; } leaf in-traffic-average-rate { type uint32; units "pps"; description "Inbound traffic average rate in packets per second (pps). The average is calculated from the start of the NSF service until the generation of this record."; } leaf in-traffic-peak-rate { type uint32; units "pps"; description "Inbound traffic peak rate in packets per second (pps)."; } leaf in-traffic-average-speed { type uint64; units "Bps"; description "Inbound traffic average speed in bytes per second (Bps). The average is calculated from the start of the NSF service until the generation of this record."; } leaf in-traffic-peak-speed { type uint64; units "Bps"; description "Inbound traffic peak speed in bytes per second (Bps)."; } leaf out-traffic-average-rate { type uint32; units "pps"; description "Outbound traffic average rate in packets per second (pps). The average is calculated from the start of the NSF service until the generation of this record."; } leaf out-traffic-peak-rate { type uint32; units "pps"; description "Outbound traffic peak rate in packets per second (pps)."; } leaf out-traffic-average-speed { type uint64; units "Bps"; description "Outbound traffic average speed in bytes per second (Bps). The average is calculated from the start of the NSF service until the generation of this record."; } leaf out-traffic-peak-speed { type uint64; units "Bps"; description "Outbound traffic peak speed in bytes per second (Bps)."; } } grouping i2nsf-system-counter-type-content{ description "A set of counters for an interface traffic data."; leaf interface-name { type if:interface-ref; description "Network interface name configured in an NSF"; reference "RFC 8343: A YANG Data Model for Interface Management"; } leaf in-total-traffic-pkts { type yang:counter32; description "Total inbound packets"; } leaf out-total-traffic-pkts { type yang:counter32; description "Total outbound packets"; } leaf in-total-traffic-bytes { type uint64; units "bytes"; description "Total inbound bytes"; } leaf out-total-traffic-bytes { type uint64; units "bytes"; description "Total outbound bytes"; } leaf in-drop-traffic-pkts { type yang:counter32; description "Total inbound drop packets"; } leaf out-drop-traffic-pkts { type yang:counter32; description "Total outbound drop packets"; } leaf in-drop-traffic-bytes { type uint64; units "bytes"; description "Total inbound drop bytes"; } leaf out-drop-traffic-bytes { type uint64; units "bytes"; description "Total outbound drop bytes"; } uses traffic-rates; } grouping i2nsf-nsf-counters-type-content{ description "A set of contents of a policy in an NSF."; leaf policy-name { type leafref { path "/nsfintf:i2nsf-security-policy" +"/nsfintf:system-policy-name"; } mandatory true; description "The name of the policy being triggered"; } leaf src-user{ type string; description "The I2NSF User's name who generates the policy."; } } grouping enable-notification { description "A grouping for enabling or disabling notification"; leaf enabled { type boolean; default "true"; description "Enables or Disables the notification. If 'true', then the notification is enabled. If 'false, then the notification is disabled."; } } grouping dampening { description "A grouping for dampening period of notification."; leaf dampening-period { type uint32; units "centiseconds"; default "0"; description "Specifies the minimum interval between the assembly of successive update records for a single receiver of a subscription. Whenever subscribed objects change and a dampening-period interval (which may be zero) has elapsed since the previous update record creation for a receiver, any subscribed objects and properties that have changed since the previous update record will have their current values marshalled and placed in a new update record. But if the subscribed objects change when the dampening-period is active, it should update the record without sending the notification until the dampening- period is finished. If multiple changes happen during the active dampening-period, it should update the record with the latest data. And at the end of the dampening-period, it should send the record as a notification with the latest updated record and restart the countdown."; reference "RFC 8641: Subscription to YANG Notifications for Datastore Updates - Section 5."; } } /* * Feature Nodes */ feature i2nsf-nsf-detection-ddos { description "This feature means it supports I2NSF nsf-detection-ddos notification"; } feature i2nsf-nsf-detection-virus { description "This feature means it supports I2NSF nsf-detection-virus notification"; } feature i2nsf-nsf-detection-intrusion { description "This feature means it supports I2NSF nsf-detection-intrusion notification"; } feature i2nsf-nsf-detection-web-attack { description "This feature means it supports I2NSF nsf-detection-web-attack notification"; } feature i2nsf-nsf-detection-voip-volte { description "This feature means it supports I2NSF nsf-detection-voip-volte notification"; } feature i2nsf-nsf-log-dpi { description "This feature means it supports I2NSF nsf-log-dpi notification"; } /* * Notification nodes */ notification i2nsf-event { description "Notification for I2NSF Event."; choice sub-event-type { description "This choice must be augmented with cases for each allowed sub-event. Only 1 sub-event will be instantiated in each i2nsf-event message. Each case is expected to define one container with all the sub-event fields."; case i2nsf-system-detection-alarm { container i2nsf-system-detection-alarm{ description "This notification is sent, when a system alarm is detected."; leaf alarm-category { type identityref { base system-alarm; } description "The alarm category for system-detection-alarm notification"; } leaf component-name { type string; description "The hardware component responsible for generating the message. Applicable for Hardware Failure Alarm."; } leaf interface-name { type if:interface-ref; description "The interface name responsible for generating the message. Applicable for Network Interface Failure Alarm."; reference "RFC 8343: A YANG Data Model for Interface Management"; } leaf interface-state { type enumeration { enum down { description "The interface state is down."; } enum up { description "The interface state is up and not congested."; } enum congested { description "The interface state is up but congested."; } } description "The state of the interface (i.e., up, down, congested). Applicable for Network Interface Failure Alarm."; } uses characteristics; uses i2nsf-system-alarm-type-content; uses common-monitoring-data; } } case i2nsf-system-detection-event { container i2nsf-system-detection-event { description "This notification is sent when a security-sensitive authentication action fails."; leaf event-category { type identityref { base system-event; } description "The event category for system-detection-event"; } uses characteristics; uses i2nsf-system-event-type-content; uses common-monitoring-data; } } case i2nsf-traffic-flows { container i2nsf-traffic-flows { description "This notification is sent to inform about the traffic flows."; leaf src-ip { type inet:ip-address-no-zone; description "The source IPv4 (or IPv6) address of the flow"; } leaf dst-ip { type inet:ip-address-no-zone; description "The destination IPv4 (or IPv6) address of the flow"; } leaf protocol { type identityref { base protocol; } description "The protocol type for nsf-detection-intrusion notification"; } leaf src-port { type inet:port-number; description "The source port of the flow"; } leaf dst-port { type inet:port-number; description "The destination port of the flow"; } leaf arrival-rate { type uint32; units "pps"; description "The average arrival rate of the flow in packets per second. The average is calculated from the start of the NSF service until the generation of this record."; } uses characteristics; uses common-monitoring-data; } } case i2nsf-nsf-detection-session-table { container i2nsf-nsf-detection-session-table { description "This notification is sent, when a session table event is detected."; leaf current-session { type uint32; description "The number of concurrent sessions"; } leaf maximum-session { type uint32; description "The maximum number of sessions that the session table can support"; } leaf threshold { type uint32; description "The threshold triggering the event"; } uses common-monitoring-data; } } } } notification i2nsf-log { description "Notification for I2NSF log. The notification is generated from the logs of the NSF."; choice sub-logs-type { description "This choice must be augmented with cases for each allowed sub-logs. Only 1 sub-event will be instantiated in each i2nsf-logs message. Each case is expected to define one container with all the sub-logs fields."; case i2nsf-nsf-system-access-log { container i2nsf-nsf-system-access-log { description "The notification is sent, if there is a new system log entry about a system access event."; leaf login-ip { type inet:ip-address-no-zone; description "Login IP address of a user"; } leaf username { type string; description "The login username that maintains the device"; } leaf login-role { type login-role; description "The login role to specify the privilege level of the user account, e.g., administrator, user, or guest."; } leaf operation-type { type operation-type; description "The operation type that the user executes"; } leaf input { type string; description "The operation performed by a user after login. The operation is a command given by a user."; } leaf output { type string; description "The result in text format after executing the input."; } uses characteristics; uses common-monitoring-data; } } case i2nsf-system-res-util-log { container i2nsf-system-res-util-log { description "This notification is sent, if there is a new log entry representing resource utilization updates."; leaf system-status { type enumeration { enum running { description "The system is active and running the security service."; } enum waiting { description "The system is active but waiting for an event to provide the security service."; } enum inactive { description "The system is inactive and not running the security service."; } } description "The current system's running status"; } leaf cpu-usage { type uint8; units "percent"; description "Specifies the relative percentage of CPU utilization with respect to platform resources"; } leaf memory-usage { type uint8; units "percent"; description "Specifies the percentage of memory usage."; } list disk { key disk-id; description "Disk is the hardware to store information for a long period, i.e., Hard Disk or Solid-State Drive."; leaf disk-id { type string; description "The ID of the storage disk. It is a free form identifier to identify the storage disk."; } leaf disk-usage { type uint8; units "percent"; description "Specifies the percentage of disk usage"; } leaf disk-left { type uint8; units "percent"; description "Specifies the percentage of disk left"; } } leaf session-num { type uint32; description "The total number of sessions"; } leaf process-num { type uint32; description "The total number of processes"; } list interface { key interface-id; description "The network interface for connecting a device with the network."; leaf interface-id { type string; description "The ID of the network interface. It is a free form identifier to identify the network interface."; } leaf in-traffic-rate { type uint32; units "pps"; description "The total inbound traffic rate in packets per second"; } leaf out-traffic-rate { type uint32; units "pps"; description "The total outbound traffic rate in packets per second"; } leaf in-traffic-speed { type uint64; units "Bps"; description "The total inbound traffic speed in bytes per second"; } leaf out-traffic-speed { type uint64; units "Bps"; description "The total outbound traffic speed in bytes per second"; } } uses characteristics; uses common-monitoring-data; } } case i2nsf-system-user-activity-log { container i2nsf-system-user-activity-log { description "This notification is sent, if there is a new user activity log entry."; uses characteristics; uses i2nsf-system-event-type-content; uses common-monitoring-data; leaf online-duration { type uint32; units "seconds"; description "The duration of a user's activeness (stays in login) during a session."; } leaf logout-duration { type uint32; units "seconds"; description "The duration of a user's inactiveness (not in login) from the last session."; } leaf additional-info { type enumeration { enum successful-login { description "The user has succeeded in login."; } enum failed-login { description "The user has failed in login (e.g., wrong password)"; } enum logout { description "The user has succeeded in logout"; } enum successful-password-changed { description "The password has been changed successfully"; } enum failed-password-changed{ description "The attempt to change password has failed"; } enum lock { description "The user has been locked. A locked user cannot login."; } enum unlock { description "The user has been unlocked."; } } description "User activities, e.g., Successful User Login, Failed Login attempts, User Logout, Successful User Password Change, Failed User Password Change, User Lockout, User Unlocking, and Unknown."; } } } } } notification i2nsf-nsf-event { description "Notification for I2NSF NSF Event. This notification is used for a specific NSF that supported such feature."; choice sub-event-type { description "This choice must be augmented with cases for each allowed sub-event. Only 1 sub-event will be instantiated in each i2nsf-event message. Each case is expected to define one container with all the sub-event fields."; case i2nsf-nsf-detection-ddos { if-feature "i2nsf-nsf-detection-ddos"; container i2nsf-nsf-detection-ddos { description "This notification is sent, when a specific flood type is detected."; leaf attack-type { type identityref { base ddos-type; } description "Any one of Syn flood, ACK flood, SYN-ACK flood, FIN/RST flood, TCP Connection flood, UDP flood, ICMP (i.e., ICMPv4 or ICMPv6) flood, HTTP flood, HTTPS flood, DNS query flood, DNS reply flood, SIP flood, etc."; } leaf start-time { type yang:date-and-time; mandatory true; description "The time stamp indicating when the attack started"; } leaf end-time { type yang:date-and-time; mandatory true; description "The time stamp indicating when the attack ended"; } leaf-list attack-src-ip { type inet:ip-address-no-zone; description "The source IPv4 (or IPv6) addresses of attack traffic. It can hold multiple IPv4 (or IPv6) addresses."; } leaf-list attack-dst-ip { type inet:ip-address-no-zone; description "The destination IPv4 (or IPv6) addresses of attack traffic. It can hold multiple IPv4 (or IPv6) addresses."; } leaf-list attack-src-port { type inet:port-number; description "The source ports of the DDoS attack"; } leaf-list attack-dst-port { type inet:port-number; description "The destination ports of the DDoS attack"; } leaf rule-name { type leafref { path "/nsfintf:i2nsf-security-policy" +"/nsfintf:rules/nsfintf:rule-name"; } mandatory true; description "The name of the I2NSF Policy Rule being triggered"; } leaf raw-info { type string; description "The information describing the packet triggering the event."; } uses attack-rates; uses log-action; uses characteristics; uses common-monitoring-data; } } case i2nsf-nsf-detection-virus { if-feature "i2nsf-nsf-detection-virus"; container i2nsf-nsf-detection-virus { description "This notification is sent, when a virus is detected."; uses i2nsf-nsf-event-type-content-extend; leaf virus { type identityref { base virus-type; } description "The virus type for nsf-detection-virus notification"; } leaf virus-name { type string; description "The name of the detected virus"; } leaf file-type { type string; description "The type of file virus code is found in (if applicable)."; reference "IANA Website: Media Types"; } leaf file-name { type string; description "The name of file virus code is found in (if applicable)."; } leaf os { type string; description "The operating system of the device."; } uses log-action; uses characteristics; uses common-monitoring-data; } } case i2nsf-nsf-detection-intrusion { if-feature "i2nsf-nsf-detection-intrusion"; container i2nsf-nsf-detection-intrusion { description "This notification is sent, when an intrusion event is detected."; uses i2nsf-nsf-event-type-content-extend; leaf protocol { type identityref { base transport-protocol; } description "The transport protocol type for nsf-detection-intrusion notification"; } leaf app { type identityref { base application-protocol; } description "The employed application layer protocol"; } leaf attack-type { type identityref { base intrusion-attack-type; } description "The sub attack type for intrusion attack"; } uses log-action; uses attack-rates; uses characteristics; uses common-monitoring-data; } } case i2nsf-nsf-detection-web-attack { if-feature "i2nsf-nsf-detection-web-attack"; container i2nsf-nsf-detection-web-attack { description "This notification is sent, when an attack event is detected."; uses i2nsf-nsf-event-type-content-extend; leaf attack-type { type identityref { base web-attack-type; } description "Concrete web attack type, e.g., SQL injection, command injection, XSS, and CSRF."; } leaf req-method { type identityref { base req-method; } description "The HTTP method of the request, e.g., PUT or GET."; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - Request Methods"; } leaf req-target { type string; description "The HTTP Request Target. This field can be filled in the format of origin-form, absolute-form, authority-form, or asterisk-form"; reference "RFC 7230: Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing - Request Target"; } leaf-list filtering-type { type identityref { base filter-type; } description "URL filtering type, e.g., deny-list, allow-list, and Unknown"; } leaf req-user-agent { type string; description "The HTTP User-Agent header field of the request"; reference "RFC 7231: Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content - User Agent"; } leaf cookies { type string; description "The HTTP Set-Cookie header field of the response"; reference "RFC 6265: HTTP State Management Mechanism - Set-Cookie"; } leaf req-host { type string; description "The HTTP Host header field of the request"; reference "RFC 7230: Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing - Host"; } leaf response-code { type string; description "The HTTP Response status code"; reference "IANA Website: Hypertext Transfer Protocol (HTTP) Status Code Registry"; } uses characteristics; uses log-action; uses common-monitoring-data; } } case i2nsf-nsf-detection-voip-volte{ if-feature "i2nsf-nsf-detection-voip-volte"; container i2nsf-nsf-detection-voip-volte { description "This notification is sent, when a VoIP/VoLTE violation is detected."; uses i2nsf-nsf-event-type-content-extend; leaf-list source-voice-id { type string; description "The detected source voice ID for VoIP and VoLTE that violates the security policy."; } leaf-list destination-voice-id { type string; description "The detected destination voice ID for VoIP and VoLTE that violates the security policy."; } leaf-list user-agent { type string; description "The detected user-agent for VoIP and VoLTE that violates the security policy."; } } } case i2nsf-nsf-log-dpi { if-feature "i2nsf-nsf-log-dpi"; container i2nsf-nsf-log-dpi { description "This notification is sent, if there is a new DPI event in the NSF log."; leaf attack-type { type dpi-type; description "The type of the DPI"; } uses characteristics; uses i2nsf-nsf-counters-type-content; uses common-monitoring-data; } } } } /* * Data nodes */ container i2nsf-counters { config false; description "The state data representing continuous value changes of information elements that occur very frequently. The value should be calculated from the start of the service of the NSF."; list system-interface { key interface-name; description "Interface counters provide the visibility of traffic into and out of an NSF, and bandwidth usage."; uses characteristics; uses i2nsf-system-counter-type-content; uses common-monitoring-data; uses timestamp; } list nsf-firewall { key policy-name; description "Firewall counters provide the visibility of traffic signatures, bandwidth usage, and how the configured security and bandwidth policies have been applied."; uses characteristics; uses i2nsf-nsf-counters-type-content; uses traffic-rates; uses common-monitoring-data; uses timestamp; } list nsf-policy-hits { key policy-name; description "Policy Hit Counters record the number of hits that traffic packets match a security policy. It can check if policy configurations are correct or not."; uses characteristics; uses i2nsf-nsf-counters-type-content; uses common-monitoring-data; leaf discontinuity-time { type yang:date-and-time; mandatory true; description "The time on the most recent occasion at which any one or more of this interface's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this node contains the time the local management subsystem re-initialized itself."; } leaf hit-times { type yang:counter32; description "The number of times a policy is hit"; } uses timestamp; } } container i2nsf-monitoring-configuration { description "The container for configuring I2NSF monitoring."; container i2nsf-system-detection-alarm { description "The container for configuring I2NSF system-detection-alarm notification"; uses enable-notification; list system-alarm { key alarm-type; description "Configuration for system alarm (i.e., CPU, Memory, and Disk Usage)"; leaf alarm-type { type enumeration { enum cpu { description "To configure the CPU usage threshold to trigger the cpu-alarm"; } enum memory { description "To configure the Memory usage threshold to trigger the memory-alarm"; } enum disk { description "To configure the Disk (storage) usage threshold to trigger the disk-alarm"; } } description "Type of alarm to be configured. The three alarm-types defined here are used to configure the threshold of the monitoring notification. The threshold is used to determine when the notification should be sent. The other two alarms defined in the module (i.e., hardware-alarm and interface-alarm) do not use any threshold value to create a notification. These alarms detect a failure or a change of state to create a notification."; } leaf threshold { type uint8 { range "1..100"; } units "percent"; description "The configuration for threshold percentage to trigger the alarm. The alarm will be triggered if the usage is exceeded the threshold."; } uses dampening; } } container i2nsf-system-detection-event { description "The container for configuring I2NSF system-detection-event notification"; uses enable-notification; uses dampening; } container i2nsf-traffic-flows { description "The container for configuring I2NSF traffic-flows notification"; uses dampening; uses enable-notification; } container i2nsf-nsf-detection-ddos { if-feature "i2nsf-nsf-detection-ddos"; description "The container for configuring I2NSF nsf-detection-ddos notification"; uses enable-notification; uses dampening; } container i2nsf-nsf-detection-session-table-configuration { description "The container for configuring I2NSF nsf-detection-session- table notification"; uses enable-notification; uses dampening; } container i2nsf-nsf-detection-intrusion { if-feature "i2nsf-nsf-detection-intrusion"; description "The container for configuring I2NSF nsf-detection-intrusion notification"; uses enable-notification; uses dampening; } container i2nsf-nsf-detection-web-attack { if-feature "i2nsf-nsf-detection-web-attack"; description "The container for configuring I2NSF nsf-detection-web-attack notification"; uses enable-notification; uses dampening; } container i2nsf-nsf-system-access-log { description "The container for configuring I2NSF system-access-log notification"; uses enable-notification; uses dampening; } container i2nsf-system-res-util-log { description "The container for configuring I2NSF system-res-util-log notification"; uses enable-notification; uses dampening; } container i2nsf-system-user-activity-log { description "The container for configuring I2NSF system-user-activity-log notification"; uses enable-notification; uses dampening; } container i2nsf-nsf-log-dpi { if-feature "i2nsf-nsf-log-dpi"; description "The container for configuring I2NSF nsf-log-dpi notification"; uses enable-notification; uses dampening; } container i2nsf-counter { description "This is used to configure the counters for monitoring an NSF"; leaf period { type uint16; units "minutes"; default 0; description "The configuration for the period interval of reporting the counter. If 0, then the counter period is disabled. If value is not 0, then the counter will be reported following the period value."; } } } } <CODE ENDS>
This section discusses the NETCONF event stream for I2NSF NSF Monitoring subscription. The YANG module in this document supports "ietf-subscribed-notifications" YANG module [RFC8639] for subscription. The reserved event stream name for this document is "I2NSF-Monitoring". The NETCONF Server (e.g., an NSF) MUST support "I2NSF-Monitoring" event stream for an NSF data collector (e.g., Security Controller). The "I2NSF-Monitoring" event stream contains all I2NSF events described in this document. The following example shows the capabilities of the event streams of an NSF (e.g., "NETCONF" and "I2NSF-Monitoring" event streams) by the subscription of an NSF data collector; note that this example XML file is delivered by an NSF to an NSF data collector. The XML examples in this document follow the line breaks as per [RFC8792].¶
<?xml version="1.0" encoding="UTF-8"?> <rpc-reply message-id="1" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0"> <data> <netconf xmlns="urn:ietf:params:xml:ns:netmod:notification"> <streams> <stream> <name>NETCONF</name> <description>Default NETCONF Event Stream</description> <replaySupport>false</replaySupport> </stream> <stream> <name>I2NSF-Monitoring</name> <description>I2NSF Monitoring Event Stream</description> <replaySupport>true</replaySupport> <replayLogCreationTime> 2021-04-29T09:37:39+00:00 </replayLogCreationTime> </stream> </streams> </netconf> </data> </rpc-reply>
This section shows the XML examples of I2NSF NSF Monitoring data delivered via Monitoring Interface from an NSF.¶
The following example shows an alarm triggered by Memory Usage of the server; note that this example XML file is delivered by an NSF to an NSF data collector:¶
<?xml version="1.0" encoding="UTF-8"?> <notification xmlns="urn:ietf:params:xml:ns:netconf:notification:1.0"> <eventTime>2021-04-29T07:43:52.181088+00:00</eventTime> <i2nsf-event xmlns="urn:ietf:params:xml:ns:yang:ietf-i2nsf-nsf-monitoring"> <i2nsf-system-detection-alarm> <alarm-category xmlns:nsfmi="urn:ietf:params:xml:ns:yang:\ ietf-i2nsf-nsf-monitoring"> nsfmi:memory-alarm </alarm-category> <acquisition-method xmlns:nsfmi="urn:ietf:params:xml:ns:yang:\ ietf-i2nsf-nsf-monitoring"> nsfmi:subscription </acquisition-method> <emission-type xmlns:nsfmi="urn:ietf:params:xml:ns:yang:\ ietf-i2nsf-nsf-monitoring"> nsfmi:on-change </emission-type> <dampening-type xmlns:nsfmi="urn:ietf:params:xml:ns:yang:\ ietf-i2nsf-nsf-monitoring"> nsfmi:on-repetition </dampening-type> <usage>91</usage> <threshold>90</threshold> <message>Memory Usage Exceeded the Threshold</message> <nsf-name>time_based_firewall</nsf-name> <severity>high</severity> </i2nsf-system-detection-alarm> </i2nsf-event> </notification>
The XML data above shows:¶
To get the I2NSF system interface counters information by query, NETCONF Client (e.g., NSF data collector) needs to initiate GET connection with NETCONF Server (e.g., NSF). The following XML file can be used to get the state data and filter the information.¶
<?xml version="1.0" encoding="UTF-8"?> <rpc xmlns="urn:ietf:params:xml:ns:netconf:base:1.0" message-id="1"> <get> <filter xmlns="urn:ietf:params:xml:ns:yang:ietf-i2nsf-nsf-monitoring"> <i2nsf-counters> <system-interface/> </i2nsf-counters> </filter> </get> </rpc>
The following XML file shows the reply from the NETCONF Server (e.g., NSF):¶
<?xml version="1.0" encoding="UTF-8"?> <rpc-reply message-id="1" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0"> <data> <i2nsf-counters xmlns="urn:ietf:params:xml:ns:yang:ietf-i2nsf-nsf-monitoring"> <system-interface> <discontinuity-time> 2021-04-29T08:43:52.181088+00:00 </discontinuity-time> <interface-name>ens3</interface-name> <acquisition-method xmlns:nsfmi="urn:ietf:params:xml:ns:yang:\ ietf-i2nsf-nsf-monitoring"> nsfmi:query </acquisition-method> <in-total-traffic-bytes>549050</in-total-traffic-bytes> <out-total-traffic-bytes>814956</out-total-traffic-bytes> <in-drop-traffic-bytes>0</in-drop-traffic-bytes> <out-drop-traffic-bytes>5078</out-drop-traffic-bytes> <nsf-name>time_based_firewall</nsf-name> </system-interface> <system-interface> <discontinuity-time> 2021-04-29T08:43:52.181088+00:00 </discontinuity-time> <interface-name>lo</interface-name> <acquisition-method xmlns:nsfmi="urn:ietf:params:xml:ns:yang:\ ietf-i2nsf-nsf-monitoring"> nsfmi:query </acquisition-method> <in-total-traffic-bytes>48487</in-total-traffic-bytes> <out-total-traffic-bytes>48487</out-total-traffic-bytes> <in-drop-traffic-bytes>0</in-drop-traffic-bytes> <out-drop-traffic-bytes>0</out-drop-traffic-bytes> <nsf-name>time_based_firewall</nsf-name> </system-interface> </i2nsf-counters> </data> </rpc-reply>
This document requests IANA to register the following URI in the "IETF XML Registry" [RFC3688]:¶
URI: urn:ietf:params:xml:ns:yang:ietf-i2nsf-nsf-monitoring Registrant Contact: The IESG. XML: N/A; the requested URI is an XML namespace.¶
This document requests IANA to register the following YANG module in the "YANG Module Names" registry [RFC7950][RFC8525]:¶
name: ietf-i2nsf-nsf-monitoring namespace: urn:ietf:params:xml:ns:yang:ietf-i2nsf-nsf-monitoring prefix: nsfmi reference: RFC XXXX // RFC Ed.: replace XXXX with an actual RFC number and remove // this note.¶
YANG module described in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].¶
The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.¶
All data nodes defined in the YANG module which can be created, modified and deleted (i.e., config true, which is the default) are considered sensitive as they all could potentially impact security monitoring and mitigation activities. Write operations (e.g., edit-config) applied to these data nodes without proper protection could result in missed alarms or incorrect alarms information being returned to the NSF data collector. There are threats that need to be considered and mitigated:¶
In addition, to defend against the DDoS attack caused by a lot of NSFs sending massive notifications to the NSF data collector, the rate limiting or similar mechanisms should be considered in both an NSF and NSF data collector, whether in advance or just in the process of DDoS attack.¶
All of the readable data nodes in this YANG module may be considered sensitive in some network environments. These data nodes represent information consistent with the logging commonly performed in network and security operations. They may reveal the specific configuration of a network; vulnerabilities in specific systems; and the deployed security controls and their relative efficacy in detecting or mitigating an attack. To an attacker, this information could inform how to (further) compromise the network, evade detection, or confirm whether they have been observed by the network operator.¶
Additionally, many of the data nodes in this YANG module such as containers "i2nsf-system-user-activity-log", "i2nsf-system-detection-event", and "i2nsf-nsf-detection-voip-volte" are privacy sensitive. They may describe specific or aggregate user activity to include associating user names with specific IP addresses; or users with specific network usage.¶
This work was supported by Institute of Information & Communications Technology Planning & Evaluation (IITP) grant funded by the Korea MSIT (Ministry of Science and ICT) (R-20160222-002755, Cloud based Security Intelligence Technology Development for the Customized Security Service Provisioning). This work was supported in part by the IITP (2020-0-00395, Standard Development of Blockchain based Network Management Automation Technology). This work was supported in part by the MSIT under the Information Technology Research Center (ITRC) support program (IITP-2021-2017-0-01633) supervised by the IITP.¶
This document is made by the group effort of I2NSF working group. Many people actively contributed to this document. The authors sincerely appreciate their contributions.¶
The following are co-authors of this document:¶
Chaehong Chung Department of Electronic, Electrical and Computer Engineering Sungkyunkwan University 2066 Seo-ro Jangan-gu Suwon, Gyeonggi-do 16419 Republic of Korea EMail: darkhong@skku.edu¶
Jinyong (Tim) Kim Department of Electronic, Electrical and Computer Engineering Sungkyunkwan University 2066 Seo-ro Jangan-gu Suwon, Gyeonggi-do 16419 Republic of Korea EMail: timkim@skku.edu¶
Dongjin Hong Department of Electronic, Electrical and Computer Engineering Sungkyunkwan University 2066 Seo-ro Jangan-gu Suwon, Gyeonggi-do 16419 Republic of Korea EMail: dong.jin@skku.edu¶
Dacheng Zhang Huawei EMail: dacheng.zhang@huawei.com¶
Yi Wu Aliababa Group EMail: anren.wy@alibaba-inc.com¶
Rakesh Kumar Juniper Networks 1133 Innovation Way Sunnyvale, CA 94089 USA EMail: rkkumar@juniper.net¶
Anil Lohiya Juniper Networks EMail: alohiya@juniper.net¶
The following changes are made from draft-ietf-i2nsf-nsf-monitoring-data-model-11:¶