Internet-Draft | Service Registration Protocol | November 2020 |
Lemon & Cheshire | Expires 22 May 2021 | [Page] |
The Service Registration Protocol for DNS-Based Service Discovery uses the standard DNS Update mechanism to enable DNS-Based Service Discovery using only unicast packets. This makes it possible to deploy DNS Service Discovery without multicast, which greatly improves scalability and improves performance on networks where multicast service is not an optimal choice, particularly 802.11 (Wi‑Fi) and 802.15.4 (IoT) networks. DNS‑SD Service registration uses public keys and SIG(0) to allow services to defend their registrations against attack.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 22 May 2021.¶
Copyright (c) 2020 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.¶
DNS-Based Service Discovery [RFC6763] is a component of Zero Configuration Networking [RFC6760] [ZC] [I-D.cheshire-dnssd-roadmap].¶
This document describes an enhancement to DNS-Based Service Discovery [RFC6763] that allows services to register their services using the DNS protocol rather than using Multicast DNS [RFC6762] (mDNS). There is already a large installed base of DNS‑SD clients that can discover services using the DNS protocol.¶
This document is intended for three audiences: implementors of software that provides services that should be advertised using DNS‑SD, implementors of DNS servers that will be used in contexts where DNS‑SD registration is needed, and administrators of networks where DNS‑SD service is required. The document is intended to provide sufficient information to allow interoperable implementation of the registration protocol.¶
DNS-Based Service Discovery (DNS‑SD) allows services to advertise the fact that they provide service, and to provide the information required to access that service. DNS‑SD clients can then discover the set of services of a particular type that are available. They can then select a service from among those that are available and obtain the information required to use it. Although DNS-SD using the DNS protocol (as opposed to mDNS) can be more efficient and versatile, it is not common in practice, because of the difficulties associated with updating authoritative DNS services with service information.¶
Existing practice for updating DNS zones is to either manually enter new data, or else use DNS Update [RFC2136]. Unfortunately DNS Update requires either that the authoritative DNS server automatically trust updates, or else that the DNS Update client have some kind of shared secret or public key that is known to the DNS server and can be used to authenticate the update. Furthermore, DNS Update can be a fairly chatty process, requiring multiple round trips with different conditional predicates to complete the update process.¶
The SRP protocol adds a set of default heuristics for processing DNS updates that eliminates the need for DNS update conditional predicates: instead, the SRP server has a set of default predicates that are applied to the update, and the update either succeeds entirely, or fails in a way that allows the registering service to know what went wrong and construct a new update.¶
SRP also adds a feature called First-Come, First-Served Naming, which allows the registering service to claim a name that is not yet in use, and, using SIG(0) [RFC2931], to authenticate both the initial claim and subsequent updates. This prevents name conflicts, since a second SRP service attempting to claim the same name will not possess the SIG(0) key used by the first service to claim it, and so its claim will be rejected and the second service will have to choose a new name.¶
Finally, SRP adds the concept of a 'lease,' similar to leases in Dynamic Host Configuration Protocol [RFC8415]. The SRP registration itself has a lease which may be on the order of an hour; if the registering service does not renew the lease before it has elapsed, the registration is removed. The claim on the name can have a longer lease, so that another service cannot claim the name, even though the registration has expired.¶
The Service Registration Protocol for DNS‑SD (SRP), described in this document, provides a reasonably secure mechanism for publishing this information. Once published, these services can be readily discovered by DNS‑SD clients using standard DNS lookups.¶
The DNS‑SD specification [RFC6763], Section 10 ("Populating the DNS with Information"), briefly discusses ways that services can publish their information in the DNS namespace. In the case of mDNS, it allows services to publish their information on the local link, using names in the ".local" namespace, which makes their services directly discoverable by peers attached to that same local link.¶
RFC6763 also allows clients to discover services using the DNS protocol [RFC1035]. This can be done by having a system administrator manually configure service information in the DNS, but manually populating DNS authoritative server databases is costly and potentially error-prone, and requires a knowledgable network administrator. Consequently, although all DNS‑SD client implementations of which we are aware support DNS‑SD using DNS queries, in practice it is used much less frequently than mDNS.¶
The Discovery Proxy [RFC8766] provides one way to automatically populate the DNS namespace, but is only appropriate on networks where services are easily advertised using mDNS. This document describes a solution more suitable for networks where multicast is inefficient, or where sleepy devices are common, by supporting both offering of services, and discovery of services, using unicast.¶
Services that implement SRP use DNS Update [RFC2136] [RFC3007] to publish service information in the DNS. Two variants exist, one for full-featured hosts, and one for devices designed for "Constrained-Node Networks" [RFC7228]. An SRP server is most likely an authoritative DNS server, or else is updating an authoritative DNS server. There is no requirement that the server that is receiving SRP requests be the same server that is answering queries that return records that have been registered.¶
Full-featured hosts are either configured manually with a registration domain, or use the "dr._dns‑sd._udp.<domain>" query ([RFC6763], Section 11) to learn the default registration domain from the network. RFC6763 says to discover the registration domain using either ".local" or a network-supplied domain name for <domain>. Services using SRP MUST use the domain name received through the DHCPv4 Domain Name option ([RFC2132], Section 3.17), if available, or the Neighbor Discovery DNS Search List option [RFC8106]. If the DNS Search List option contains more than one domain name, it MUST NOT be used. If neither option is available, the Service Registration protocol is not available on the local network.¶
Manual configuration of the registration domain can be done either by querying the list of available registration zones ("r._dns‑sd._udp") and allowing the user to select one from the UI, or by any other means appropriate to the particular use case being addressed. Full-featured devices construct the names of the SRV, TXT, and PTR records describing their service(s) as subdomains of the chosen service registration domain. For these names they then discover the zone apex of the closest enclosing DNS zone using SOA queries [RFC8765]. Having discovered the enclosing DNS zone, they query for the "_dnssd‑srp._tcp.<zone>" SRV record to discover the server to which they should send DNS updates. Hosts that support SRP updates using TLS use the "_dnssd‑srp‑tls._tcp.<zone>" SRV record instead.¶
For devices designed for Constrained-Node Networks [RFC7228] some simplifications are available. Instead of being configured with (or discovering) the service registration domain, the (proposed) special-use domain name (see [RFC6761]) "default.service.arpa" is used. The details of how SRP server(s) are discovered will be specific to the constrained network, and therefore we do not suggest a specific mechanism here.¶
SRP clients on constrained networks are expected to receive from the network a list of SRP servers with which to register. It is the responsibility of a Constrained-Node Network supporting SRP to provide one or more SRP server addresses. It is the responsibility of the SRP server supporting a Constrained-Node Network to handle the updates appropriately. In some network environments, updates may be accepted directly into a local "default.service.arpa" zone, which has only local visibility. In other network environments, updates for names ending in "default.service.arpa" may be rewritten internally to names with broader visibility.¶
The reason for these different assumptions is that low-power devices that typically use Constrained-Node Networks may have very limited battery power. The series of DNS lookups required to discover an SRP server and then communicate with it will increase the power required to advertise a service; for low-power devices, the additional flexibility this provides does not justify the additional use of power. It is also fairly typical of such networks that some network service information is obtained as part of the process of joining the network, and so this can be relied upon to provide nodes with the information they need.¶
Networks that are not constrained networks can more complicated topologies at the Internet layer. Nodes connected to such networks can be assumed to be able to do DNSSD service registration domain discovery. Such networks are generally able to provide registration domain discovery and routing. By requiring the use of TCP, the possibility of off-network spoofing is eliminated.¶
We will discuss several parts to this process: how to know what to publish, how to know where to publish it (under what name), how to publish it, how to secure its publication, and how to maintain the information once published.¶
We refer to the DNS Update message sent by services using SRP as an SRP update. Three types of updates appear in an SRP update: Service Discovery records, Service Description records, and Host Description records.¶
RFC 6763 describes the details of what each of these types of updates contains and is the definitive source for information about what to publish; the reason for summarizing this here is to provide the reader with enough information about what will be published that the service registration process can be understood at a high level without first learning the full details of DNS‑SD. Also, the "Service Instance Name" is an important aspect of first-come, first-serve naming, which we describe later on in this document.¶
Multicast DNS uses a single namespace, ".local", which is valid on the local link. This convenience is not available for DNS‑SD using the DNS protocol: services must exist in some specific unicast namespace.¶
As described above, full-featured devices are responsible for knowing in what domain they should register their services. Devices made for Constrained-Node Networks register in the (proposed) special use domain name [RFC6761] "default.service.arpa", and let the SRP server handle rewriting that to a different domain if necessary.¶
It is possible to issue a DNS Update that does several things at once; this means that it's possible to do all the work of adding a PTR resource record to the PTR RRset on the Service Name, and creating or updating the Service Instance Name and Host Description, in a single transaction.¶
An SRP update takes advantage of this: it is implemented as a single DNS Update message that contains a service's Service Discovery records, Service Description records, and Host Description records.¶
Updates done according to this specification are somewhat different than regular DNS Updates as defined in RFC2136. The RFC2136 update process can involve many update attempts: you might first attempt to add a name if it doesn't exist; if that fails, then in a second message you might update the name if it does exist but matches certain preconditions. Because the registration protocol uses a single transaction, some of this adaptability is lost.¶
In order to allow updates to happen in a single transaction, SRP updates do not include update prerequisites. The requirements specified in Section 2.3 are implicit in the processing of SRP updates, and so there is no need for the service sending the SRP update to put in any explicit prerequisites.¶
DNS‑SD Service Registration is based on standard RFC2136 DNS Update, with some differences:¶
Traditional DNS update is secured using the TSIG protocol, which uses a secret key shared between the DNS Update client (which issues the update) and the server (which authenticates it). This model does not work for automatic service registration.¶
The goal of securing the DNS‑SD Registration Protocol is to provide the best possible security given the constraint that service registration has to be automatic. It is possible to layer more operational security on top of what we describe here, but what we describe here is an improvement over the security of mDNS. The goal is not to provide the level of security of a network managed by a skilled operator.¶
First-Come First-Serve naming provides a limited degree of security: a service that registers its service using DNS‑SD Registration protocol is given ownership of a name for an extended period of time based on the key used to authenticate the DNS Update. As long as the registration service remembers the name and the key used to register that name, no other service can add or update the information associated with that. FCFS naming is used to protect both the Service Description and the Host Description.¶
The service generates a public/private key pair. This key pair MUST be stored in stable storage; if there is no writable stable storage on the SRP client, the SRP client MUST be pre-configured with a public/private key pair in read-only storage that can be used. This key pair MUST be unique to the device. This key pair MUST be unique to the device. A device with rewritable storage should retain this key indefinitely. When the device changes ownership, it may be appropriate to erase the old key and install a new one. Therefore the key MAY be overwritten as a result of a full reset of the device (e.g., a "factory reset").¶
When sending DNS updates, the service includes a KEY record containing the public portion of the key in each Host Description update and each Service Description update. Each KEY record MUST contain the same public key. The update is signed using SIG(0), using the private key that corresponds to the public key in the KEY record. The lifetimes of the records in the update is set using the EDNS(0) Update Lease option [I-D.sekar-dns-ul].¶
The KEY record in Service Description updates MAY be omitted for brevity; if it is omitted, the SRP server MUST behave as if the same KEY record that is given for the Host Description is also given for each Service Description for which no KEY record is provided. Omitted KEY records are not used when computing the SIG(0) signature.¶
Both Host Description records and Service Description Records can have names that result in name conflicts. Service Discovery records cannot have name conflicts. If any Host Description or Service Description record is found by the server to have a conflict with an existing name, the server will respond to the SRP Update with a YXDOMAIN rcode. In this case, the Service MUST either abandon the service registration attempt, or else choose a new name.¶
There is no specific requirement for how this is done; typically, however, the service will append a number to the preferred name. This number could be sequentially increasing, or could be chosen randomly. One existing implementation attempts several sequential numbers before choosing randomly. So for instance, it might try host.service.arpa, then host-1.service.arpa, then host-2.service.arpa, then host-31773.service.arpa.¶
The lifetime of the DNS‑SD PTR, SRV, A, AAAA and TXT records [RFC6763] uses the LEASE field of the Update Lease option, and is typically set to two hours. This means that if a device is disconnected from the network, it does not appear in the user interfaces of devices looking for services of that type for too long.¶
The lifetime of the KEY records is set using the KEY-LEASE field of the Update Lease Option, and should be set to a much longer time, typically 14 days. The result of this is that even though a device may be temporarily unplugged, disappearing from the network for a few days, it makes a claim on its name that lasts much longer.¶
This means that even if a device is unplugged from the network for a few days, and its services are not available for that time, no other device can come along and claim its name the moment it disappears from the network. In the event that a device is unplugged from the network and permanently discarded, then its name is eventually cleaned up and made available for re-use.¶
Although [RFC2782] requires that the target name in the SRV record not be compressed, an SRP client SHOULD compress the target in the SRV record. The motivation for not compressing in RFC2782 is not stated, but is assumed to be because a caching resolver that does not understand the format of the SRV record might store it as binary data and thus return an invalid pointer in response to a query. This does not apply in the case of SRP case: an SRP server needs to understand SRV records in order to validate the SRP update. Compression of the target potentially saves substantial space in the SRP update.¶
To remove a service registration, the SRP client retransmits its most recent update with an Update Lease option that has a LEASE value of zero. If the registration is to be permanently removed, KEY-LEASE should also be zero. Otherwise, it should have the same value it had previously; this holds the name in reserve for when the SRP client is once again able to provide the service.¶
SRP clients are normally expected to remove all service instances when removing a host. However, in some cases a SRP client may not have retained sufficient state to know that some service instance is pointing to a host that it is removing. An SRP server can assume that all service instances pointing to a host entry that's being removed are no longer valid. Therefore, SRP servers MAY remove all service instances pointing to a host when a host is removed, even if the SRP client doesn't remove them explicitly.¶
The SRP server first validates that the DNS Update is a syntactically and semantically valid DNS Update according to the rules specified in RFC2136.¶
SRP Updates consist of a set of instructions that together add one or more services. Each instruction consists either of a single add, or a delete followed by an add. When an instruction contains a delete and an add, the delete MUST precede the add.¶
The SRP server checks each instruction in the SRP update to see that it is either a Service Discovery update, a Service Description update, or a Host Description update. Order matters in DNS updates. Specifically, deletes must precede adds for records that the deletes would affect; otherwise the add will have no effect. This is the only ordering constraint; aside from this constraint, updates may appear in whatever order is convenient when constructing the update.¶
Because the SRP update is a DNS update, it MUST contain a single question that indicates the zone to be updated. Every delete and update in an SRP update MUST be within the zone that is specified for the SRP Update.¶
An Instruction is a Service Discovery Instruction if it contains¶
An Instruction is a Service Description Instruction if, for the appropriate Service Instance Name, it contains¶
An SRP server MUST correctly handle compressed names in the SRV target.¶
An Instruction is a Host Description Instruction if, for the appropriate hostname, it contains¶
An SRP Update MUST include at zero or more Service Discovery Instructions, the same number of Service Description Instructions, and exactly one Host Description Instruction. A DNS Update that does not is not an SRP update. A DNS Update that contains any other adds, any other deletes, or any prerequisites, is not an SRP update. Such messages should either be processed as regular RFC2136 updates, including access control checks and constraint checks, if supported, or else rejected with RCODE=REFUSED.¶
In addition, in order for an update to be a valid SRP update, the target of every Service Discovery Instruction MUST be a Service Description Instruction that is present in the SRP Update. There MUST NOT be any Service Description Instruction to which no Service Discovery Instruction points. The target of the SRV record in every Service Description instruction MUST be the single Host Description Instruction.¶
If the definitions of each of these instructions are followed carefully and the update requirements are validated correctly, many DNS Updates that look very much like SRP updates nevertheless will fail to validate. For example, a DNS update that contains an RRset Add to a Service Name and an RRset Add to a Service Instance Name, where the Service Name does not reference the Service Instance Name, is not a valid SRP update message, but may be a valid RFC2136 update.¶
Assuming that a DNS Update message has been validated with these conditions and is a valid SRP Update, the server checks that the name in the Host Description Instruction exists. If so, then the server checks to see if the KEY record on that name is the same as the KEY record in the Host Description Instruction. The server performs the same check for the KEY records in any Service Description Instructions. For KEY records that were omitted from Service Description Instructions, the KEY from the Host Description Instruction is used. If any existing KEY record corresponding to a KEY record in the SRP Update does not match the KEY same record in the SRP Update (whether provided or taken from the Host Description Instruction), then the server MUST reject the SRP Update with the YXDOMAIN RCODE.¶
Otherwise, the server validates the SRP Update using SIG(0) on the public key in the KEY record of the Host Description update. If the validation fails, the server MUST reject the SRP Update with the REFUSED RCODE. Otherwise, the SRP update is considered valid and authentic, and is processed according to the method described in RFC2136.¶
KEY record updates omitted from Service Description update are processed as if they had been explicitly present: every Service Description that is updated MUST, after the update, have a KEY RR, and it must be the same KEY RR that is present in the Host Description to which the Service Description refers.¶
The status that is returned depends on the result of processing the update, and can be either SUCCESS or SERVFAIL: all other possible outcomes should already have been accounted for when applying the constraints that qualify the update as an SRP Update.¶
The server MAY add a Reverse Mapping that corresponds to the Host Description. This is not required because the Reverse Mapping serves no protocol function, but it may be useful for debugging, e.g. in annotating network packet traces or logs. In order for the server to add a reverse mapping update, it must be authoritative for the zone or have credentials to do the update. The SRP client MAY also do a reverse mapping update if it has credentials to do so.¶
The server MAY apply additional criteria when accepting updates. In some networks, it may be possible to do out-of-band registration of keys, and only accept updates from pre-registered keys. In this case, an update for a key that has not been registered should be rejected with the REFUSED RCODE.¶
There are at least two benefits to doing this rather than simply using normal SIG(0) DNS updates. First, the same registration protocol can be used in both cases, so both use cases can be addressed by the same service implementation. Second, the registration protocol includes maintenance functionality not present with normal DNS updates.¶
Note that the semantics of using SRP in this way are different than for typical RFC2136 implementations: the KEY used to sign the SRP update only allows the SRP client to update records that refer to its Host Description. RFC2136 implementations do not normally provide a way to enforce a constraint of this type.¶
The server may also have a dictionary of names or name patterns that are not permitted. If such a list is used, updates for Service Instance Names that match entries in the dictionary are rejected with YXDOMAIN.¶
All RRs within an RRset are required to have the same TTL (Clarifications to the DNS Specification [RFC2181], Section 5.2). In order to avoid inconsistencies, SRP places restrictions on TTLs sent by services and requires that SRP servers enforce consistency.¶
Services sending SRP updates MUST use consistent TTLs in all RRs within the SRP update.¶
SRP update servers MUST check that the TTLs for all RRs within the SRP update are the same. If they are not, the SRP update MUST be rejected with a REFUSED RCODE.¶
Additionally, when adding RRs to an RRset, for example when processing Service Discovery records, the server MUST use the same TTL on all RRs in the RRset. How this consistency is enforced is up to the implementation.¶
TTLs sent in SRP updates are advisory: they indicate the SRP client's guess as to what a good TTL would be. SRP servers may override these TTLs. SRP servers SHOULD ensure that TTLs are reasonable: neither too long nor too short. The TTL should never be longer than the lease time (Section 4.1). Shorter TTLs will result in more frequent data refreshes; this increases latency on the DNS-SD client side, increases load on any caching resolvers and on the authoritative server, and also increases network load, which may be an issue for constrained networks. Longer TTLs will increase the likelihood that data in caches will be stale. TTL minimums and maximums SHOULD be configurable by the operator of the SRP server.¶
Because the DNS‑SD registration protocol is automatic, and not managed by humans, some additional bookkeeping is required. When an update is constructed by the SRP client, it MUST include an EDNS(0) Update Lease Option [I-D.sekar-dns-ul]. The Update Lease Option contains two lease times: the Lease Time and the Key Lease Time.¶
These leases are promises, similar to DHCP leases [RFC2131], from the SRP client that it will send a new update for the service registration before the lease time expires. The Lease time is chosen to represent the time after the update during which the registered records other than the KEY record should be assumed to be valid. The Key Lease time represents the time after the update during which the KEY record should be assumed to be valid.¶
The reasoning behind the different lease times is discussed in the section on first-come, first-served naming (Section 2.2.4.1). SRP servers may be configured with limits for these values. A default limit of two hours for the Lease and 14 days for the SIG(0) KEY are currently thought to be good choices. Constrained devices with limited battery that wake infrequently are likely to negotiate longer leases. SRP clients that are going to continue to use names on which they hold leases should update well before the lease ends, in case the registration service is unavailable or under heavy load.¶
The SRP server MUST include an EDNS(0) Update Lease option in the response if the lease time proposed by the service has been shortened or lengthened. The service MUST check for the EDNS(0) Update Lease option in the response and MUST use the lease times from that option in place of the options that it sent to the server when deciding when to update its registration. The times may be shorter or longer than those specified in the SRP update; the SRP client must honor them in either case.¶
SRP clients should assume that each lease ends N seconds after the update was first transmitted, where N is the lease duration. Servers should assume that each lease ends N seconds after the update that was successfully processed was received. Because the server will always receive the update after the SRP client sent it, this avoids the possibility of misunderstandings.¶
SRP servers MUST reject updates that do not include an EDNS(0) Update Lease option. Dual-use servers MAY accept updates that don't include leases, but SHOULD differentiate between SRP updates and other updates, and MUST reject updates that would otherwise be SRP updates if they do not include leases.¶
Lease times have a completely different function than TTLs. On an authoritative DNS server, the TTL on a resource record is a constant: whenever that RR is served in a DNS response, the TTL value sent in the answer is the same. The lease time is never sent as a TTL; its sole purpose is to determine when the authoritative DNS server will delete stale records. It is not an error to send a DNS response with a TTL of 'n' when the remaining time on the lease is less than 'n'.¶
Another use of SRP is for devices that sleep to reduce power consumption.¶
In this case, in addition to the DNS Update Lease option [I-D.sekar-dns-ul] described above, the device includes an EDNS(0) OWNER Option [I-D.cheshire-edns0-owner-option].¶
The EDNS(0) Update Lease option constitutes a promise by the device that it will wake up before this time elapses, to renew its registration and thereby demonstrate that it is still attached to the network. If it fails to renew the registration by this time, that indicates that it is no longer attached to the network, and its registration (except for the KEY in the Host Description) should be deleted.¶
The EDNS(0) OWNER Option indicates that the device will be asleep, and will not be receptive to normal network traffic. When a DNS server receives a DNS Update with an EDNS(0) OWNER Option, that signifies that the SRP server should set up a proxy for any IPv4 or IPv6 address records in the DNS Update message. This proxy should send ARP or ND messages claiming ownership of the IPv4 and/or IPv6 addresses in the records in question. In addition, the proxy should answer future ARP or ND requests for those IPv4 and/or IPv6 addresses, claiming ownership of them. When the DNS server receives a TCP SYN or UDP packet addressed to one of the IPv4 or IPv6 addresses for which it proxying, it should then wake up the sleeping device using the information in the EDNS(0) OWNER Option. At present version 0 of the OWNER Option specifies the "Wake-on-LAN Magic Packet" that needs to be sent; future versions could be extended to specify other wakeup mechanisms.¶
Note that although the authoritative DNS server that implements the SRP function need not be on the same link as the sleeping host, the Sleep Proxy must be on the same link.¶
It is not required that sleepy nodes on a Constrained-Node Network support sleep proxy. Such devices may have different mechanisms for dealing with sleep and wakeup. An SRP registration for such a device will be useful regardless of the mechanism whereby messages are delivered to the sleepy end device. For example, the message might be held in a buffer for an extended period of time by an intermediate device on a mesh network, and then delivered to the device when it wakes up. The exact details of such behaviors are out of scope for this document.¶
SRP updates have no authorization semantics other than first-come, first-served. This means that if an attacker from outside of the administrative domain of the server knows the server's IP address, it can in principle send updates to the server that will be processed successfully. Servers should therefore be configured to reject updates from source addresses outside of the administrative domain of the server.¶
For updates sent to an anycast IP address of an SRP server, this validation must be enforced by every router on the path from the Constrained-Device Network to the unconstrained portion of the network. For TCP updates, the initial SYN-SYN+ACK handshake prevents updates being forged by an off-network attacker. In order to ensure that this handshake happens, Service Discovery Protocol servers relying on three-way-handshake validation MUST NOT accept TCP Fast Open payloads. If the network infrastructure allows it, an SRP server MAY accept TCP Fast Open payloads if all such packets are validated along the path, and the network is able to reject this type of spoofing at all ingress points.¶
Note that these rules only apply to the validation of SRP updates. A server that accepts updates from SRP clients may also accept other DNS updates, and those DNS updates may be validated using different rules. However, in the case of a DNS service that accepts SRP updates, the intersection of the SRP update rules and whatever other update rules are present must be considered very carefully.¶
For example, a normal, authenticated DNS update to any RR that was added using SRP, but that is authenticated using a different key, could be used to override a promise made by the registration protocol, by replacing all or part of the service registration information with information provided by an SRP client. An implementation that allows both kinds of updates should not allow DNS Update clients to updateupdate records added by SRP clients using different authentication and authorization credentials.¶
This specification does not provide a mechanism for validating responses from DNS servers to SRP clients. In the case of Constrained Network/Constrained Node clients, such validation isn't practical because there's no way to establish trust. In principle, a KEY RR could be used by a non-constrained SRP client to validate responses from the server, but this is not required, nor do we specify a mechanism for determining which key to use.¶
For validation, SRP servers MUST implement the ECDSAP256SHA256 signature algorithm. SRP servers SHOULD implement the algorithms specified in [RFC8624], Section 3.1, in the validation column of the table, that are numbered 13 or higher and have a "MUST", "RECOMMENDED", or "MAY" designation in the validation column of the table. SRP clients MUST NOT assume that any algorithm numbered lower than 13 is available for use in validating SIG(0) signatures.¶
Because DNSSD SRP updates can be sent off-link, the privacy implications of SRP are different than for multicast DNS responses. Host implementations that are using TCP SHOULD also use TLS if available. Server implementations MUST offer TLS support. The use of TLS with DNS is described in [RFC7858] and [RFC8310].¶
Hosts that implement TLS support SHOULD NOT fall back to TCP; since servers are required to support TLS, it is entirely up to the host implementation whether to use it.¶
Public keys can be used as identifiers to track hosts. SRP servers MAY elect not to return KEY records for queries for SRP registrations.¶
In order to be fully functional, the owner of the 'arpa.' zone must add a delegation of 'service.arpa.' in the '.arpa.' zone [RFC3172]. This delegation should be set up as was done for 'home.arpa', as a result of the specification in Section 7 of [RFC8375].¶
IANA is requested to record the domain name 'service.arpa.' in the Special-Use Domain Names registry [SUDN]. IANA is requested, with the approval of IAB, to implement the delegation requested in Section 8.¶
IANA is further requested to add a new entry to the "Transport-Independent Locally-Served Zones" subregistry of the the "Locally-Served DNS Zones" registry [LSDZ]. The entry will be for the domain 'service.arpa.' with the description "DNS‑SD Registration Protocol Special-Use Domain", listing this document as the reference.¶
IANA is also requested to add a new entry to the Service Names and Port Numbers registry for dnssd-srp with a transport type of tcp. No port number is to be assigned. The reference should be to this document, and the Assignee and Contact information should reference the authors of this document. The Description should be as follows:¶
Availability of DNS Service Discovery Service Registration Protocol Service for a given domain is advertised using the "_dnssd‑srp._tcp.<domain>." SRV record gives the target host and port where DNSSD Service Registration Service is provided for the named domain.¶
IANA is also requested to add a new entry to the Service Names and Port Numbers registry for dnssd-srp with a transport type of tcp. No port number is to be assigned. The reference should be to this document, and the Assignee and Contact information should reference the authors of this document. The Description should be as follows:¶
Availability of DNS Service Discovery Service Registration Protocol Service for a given domain over TLS is advertised using the "_dnssd‑srp‑tls._tcp.<domain>." SRV record gives the target host and port where DNSSD Service Registration Service is provided for the named domain.¶
IANA is requested to allocate an IPv6 Anycast address from the IPv6 Special-Purpose Address Registry, similar to the Port Control Protocol anycast address, 2001:1::1. The value TBD should be replaced with the actual allocation in the table that follows. The values for the registry are:¶
Attribute | value |
Address Block | 2001:1::TBD/128 |
Name | DNS-SD Service Registration Protocol Anycast Address |
RFC | [this document] |
Allocation Date | [date of allocation] |
Termination Date | N/A |
Source | True |
Destination | True |
Forwardable | True |
Global | True |
Reserved-by-protocol | False |
Thanks to Toke Høiland-Jørgensen, Jonathan Hui and Esko Dijk for their thorough technical reviews, to Tamara Kemper for doing a nice developmental edit, Tim Wattenberg for doing a service implementation at the Montreal Hackathon at IETF 102, and Tom Pusateri for reviewing during the hackathon and afterwards.¶
It may be useful to set up a DNS server for testing that does not implement SRP. This can be done by configuring the server to listen on the anycast address, or advertising it in the _dnssd‑srp._tcp.<zone> SRV and _dnssd‑srp‑tls._tcp.<zone> record. It must be configured to be authoritative for "default.service.arpa", and to accept updates from hosts on local networks for names under "default.service.arpa" without authentication, since such servers will not have support for FCFS authentication (Section 2.2.4.1).¶
A server configured in this way will be able to successfully accept and process SRP updates from services that send SRP updates. However, no prerequisites will be applied, and this means that the test server will accept internally inconsistent SRP updates, and will not stop two SRP updates, sent by different services, that claim the same name(s), from overwriting each other.¶
Since SRP updates are signed with keys, validation of the SIG(0) algorithm used by the client can be done by manually installing the client public key on the DNS server that will be receiving the updates. The key can then be used to authenticate the client, and can be used as a requirement for the update. An example configuration for testing SRP using BIND 9 is given in Appendix C.¶
Ordinarily SRP updates will fail when sent to an RFC 2136-compliant server that does not implement SRP because the zone being updated is "default.service.arpa", and no DNS server that is not an SRP server should normally be configured to be authoritative for "default.service.arpa". Therefore, a service that sends an SRP update can tell that the receiving server does not support SRP, but does support RFC2136, because the RCODE will either be NOTZONE, NOTAUTH or REFUSED, or because there is no response to the update request (when using the anycast address)¶
In this case a service MAY attempt to register itself using regular RFC2136 DNS updates. To do so, it must discover the default registration zone and the DNS server designated to receive updates for that zone, as described earlier, using the _dns‑update._udp SRV record. It can then make the update using the port and host pointed to by the SRV record, and should use appropriate prerequisites to avoid overwriting competing records. Such updates are out of scope for SRP, and a service that implements SRP MUST first attempt to use SRP to register itself, and should only attempt to use RFC2136 backwards compatibility if that fails. Although the owner name for the SRV record specifies the UDP protocol for updates, it is also possible to use TCP, and TCP should be required to prevent spoofing.¶
zone "default.service.arpa." { type master; file "/etc/bind/master/service.db"; allow-update { key demo.default.service.arpa.; }; };
$ORIGIN . $TTL 57600 ; 16 hours default.service.arpa IN SOA ns3.default.service.arpa. postmaster.default.service.arpa. ( 2951053287 ; serial 3600 ; refresh (1 hour) 1800 ; retry (30 minutes) 604800 ; expire (1 week) 3600 ; minimum (1 hour) ) NS ns3.default.service.arpa. SRV 0 0 53 ns3.default.service.arpa. $ORIGIN default.service.arpa. $TTL 3600 ; 1 hour _ipps._tcp PTR demo._ipps._tcp $ORIGIN _ipps._tcp.default.service.arpa. demo TXT "0" SRV 0 0 9992 demo.default.service.arpa. $ORIGIN _udp.default.service.arpa. $TTL 3600 ; 1 hour _dns-update PTR ns3.default.service.arpa. $ORIGIN _tcp.default.service.arpa. _dnssd-srp PTR ns3.default.service.arpa. $ORIGIN default.service.arpa. $TTL 300 ; 5 minutes ns3 AAAA 2001:db8:0:1::1 $TTL 3600 ; 1 hour demo AAAA 2001:db8:0:2::1 KEY 513 3 13 ( qweEmaaq0FAWok5//ftuQtZgiZoiFSUsm0srWREdywQU 9dpvtOhrdKWUuPT3uEFF5TZU6B4q1z1I662GdaUwqg== ); alg = ECDSAP256SHA256 ; key id = 15008 AAAA ::1