Protocol for Access Node Control Mechanism in Broadband Networks
draft-ietf-ancp-protocol-05

Status of this Memo

This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.

The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.

This Internet-Draft will expire on September 10, 2009.

Copyright Notice

Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document.

Abstract

This document describes proposed extensions to the GSMPv3 protocol to allow its use in a broadband environment, as a control plane between Access Nodes (e.g. DSLAM) and Broadband Network Gateways (e.g. NAS). These proposed extensions are required to realize a protocol for "Access Node Control" mechanism as described in [ANCP‑FRAMEWORK] (Ooghe, S., Voigt, N., Platnic, M., Haag, T., and S. Wadhwa, “Framework and Requirements for an Access Node Control Mechanism in Broadband Multi-Service Networks,” February 2009.). The resulting protocol with the proposed extensions to GSMPv3 [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.) is referred to as "Access Node Control Protocol" (ANCP). This document currently focuses on specific use cases of access node control mechanism for topology discovery, line configuration, and OAM as described in ANCP framework document [ANCP‑FRAMEWORK] (Ooghe, S., Voigt, N., Platnic, M., Haag, T., and S. Wadhwa, “Framework and Requirements for an Access Node Control Mechanism in Broadband Multi-Service Networks,” February 2009.). It is intended to be augmented by additional protocol specification for future use cases considered in scope by the ANCP charter.

ANCP framework document [ANCP‑FRAMEWORK] (Ooghe, S., Voigt, N., Platnic, M., Haag, T., and S. Wadhwa, “Framework and Requirements for an Access Node Control Mechanism in Broadband Multi-Service Networks,” February 2009.) describes the ANCP use-cases in detail. Illustrative text for the use-cases is included here to help the protocol implementer understand the greater context of ANCP protocol interactions.

Table of Contents

1.  Specification Requirements
2.  Introduction
    2.1.  Terminology
3.  Broadband Access Aggregation
    3.1.  ATM-based broadband aggregation
    3.2.  Ethernet-based broadband aggregation
4.  Access Node Control Protocol
    4.1.  Overview
    4.2.  ANCP based Access Topology Discovery
        4.2.1.  Goals
        4.2.2.  Message Flow
    4.3.  ANCP based Line Configuration
        4.3.1.  Goals
        4.3.2.  Message Flow
    4.4.  ANCP based Transactional Multicast
        4.4.1.  Goals
        4.4.2.  Message Flow
    4.5.  ANCP based OAM
        4.5.1.  Message Flow
5.  Access Node Control Protocol (ANCP)
    5.1.  ANCP/TCP connection establishment
    5.2.  ANCP Connection keep-alive
    5.3.  Capability negotiation
    5.4.  GSMP Message Extensions for Access Node Control
        5.4.1.  General Extensions
        5.4.2.  Topology Discovery Extensions
        5.4.3.  Line Configuration Extensions
        5.4.4.  OAM Extensions
        5.4.5.  Multicast Extensions
            5.4.5.1.  General well known TLVs
                5.4.5.1.1.  Target TLV
                5.4.5.1.2.  Command TLV
                5.4.5.1.3.  Status-Info TLV
            5.4.5.2.  Multicast Replication Control Message
            5.4.5.3.  Multicast Status Message
    5.5.  ATM-specific considerations
    5.6.  Ethernet-specific considerations
6.  IANA Considerations
7.  Security Considerations
8.  Acknowledgements
9.  References
    9.1.  Normative References
    9.2.  Informative References
§  Authors' Addresses

1.  Specification Requirements

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.).

2.  Introduction

DSL is a widely deployed access technology for Broadband Access for Next Generation Networks. Several specifications like [TR‑059] (Anschutz, T., “DSL Forum TR-059, DSL Evolution - Architecture Requirements for the Support of QoS-Enabled IP Services,” September 2003.), [TR‑058] (Elias, M. and S. Ooghe, “DSL Forum TR-058, Multi-Service Architecture & Framework Requirements,” September 2003.), [TR‑092] (, “DSL Forum TR-092, Broadband Remote access server requirements document,” 2005.) describe possible architectures for these access networks. In the scope of these specifications are the delivery of voice, video and data services.

When deploying value-added services across DSL access networks, special attention regarding quality of service and service control is required, which implies a tighter coordination between network elements in the broadband access network without burdening the OSS layer.

This draft defines extensions and modifications to GSMPv3 (specified in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.)) and certain new mechanisms to realize a control plane between a service-oriented layer 3 edge device (the NAS) and a layer2 Access Node (e.g. DSLAM) in order to perform QoS-related, service- related and subscriber-related operations. The control protocol as a result of these extensions and mechanisms is referred to as "Access Node Control Protocol" (ANCP).

ANCP uses the option of transporting GSMPv3 over TCP/IP. TCP encapsulation for GSMPv3 is defined in [RFC3293] (Worster, T., Doria, A., and and J. Buerkle, “General Switch Management Protocol (GSMP) Packet Encapsulations for Asynchronous Transfer Mode (ATM), Ethernet and Transmission Control Protocol (TCP),” June 2002.). GSMPv3 encapsulation directly over Ethernet and ATM as defined in [RFC3293] is not considered for ANCP.

ANCP uses a subset of GSMPv3 messages to implement currently defined use-cases. These relevant GSMPv3 messages are identified in section Section 5 (Access Node Control Protocol (ANCP)). GSMPv3 procedures with suitable extensions, as used by ANCP, are described in sections Section 5.1 (ANCP/TCP connection establishment), Section 5.2 (ANCP Connection keep-alive) and Section 5.3 (Capability negotiation). GSMPv3 general extensions and GSMPv3 message specific extensions required by ANCP are described in sub-sections of Section 5.4 (GSMP Message Extensions for Access Node Control). In addition to specifying extensions and modifications to relevant GSMP messages applicable to ANCP, this draft also defines the usage of these messages by ANCP. Not all the fields in relevant GSMP messages are used by ANCP. This draft indicates the value that ANCP should set for the fields in these GSMP messages.

2.1.  Terminology

• Access Node (AN): Network device, usually located at a service provider central office or street cabinet that terminates access (local) loop connections from subscribers. In case the access loop is a Digital Subscriber Line (DSL), the Access Node provides DSL signal termination, and is referred to as DSL Access Multiplexer (DSLAM).
• Network Access Server (NAS): Network element which aggregates subscriber traffic from a number of Access Nodes. The NAS is an injection point for policy management and IP QoS in the access network. IT is also referred to as Broadband Network Gateway (BNG) or Broadband Remote Access Server (BRAS).
• Home Gateway (HGW): Network element that connects subscriber devices to the Access Node and the access network. In case of DSL, the Home Gateway is a DSL network termination that could either operate as a layer 2 bridge or as a layer 3 router. In the latter case, such a device is also referred to as a Routing Gateway (RG).
• Net Data Rate: portion of the total data rate of the DSL line that can be used to transmit actual user information (e.g. ATM cells of Ethernet frames). It excludes overhead that pertains to the physical transmission mechanism (e.g. trellis coding in case of DSL). This is defined in section 3.39 of ITU-T G.993.2.
• DSL line (synch) rate: the total data rate of the DSL line, including the overhead attributable to the physical transmission mechanism.
• DSL multi-pair bonding: method for bonding (or aggregating) multiple xDSL lines into a single bi-directional logical link, henceforth referred to in this draft as "DSL bonded circuit". DSL "multi-pair" bonding allows an operator to combine the data rates on two or more copper pairs, and deliver the aggregate data rate to a single customer. ITU-T recommendations G.998.1 and G.998.2 respectively describe ATM and Ethernet based multi-pair bonding.

3.  Broadband Access Aggregation

3.1.  ATM-based broadband aggregation

End to end DSL network consists of network and application service provider networks (NSP and ASP networks), regional/access network, and customer premises network. Figure 1 (ATM Broadband Aggregation Topology ) shows ATM broadband access network components.

The Regional/Access Network consists of the Regional Network, Network Access Server, and the Access Network as show in Figure 1 (ATM Broadband Aggregation Topology ). Its primary function is to provide end-to-end transport between the customer premises and the NSP or ASP. The Access Node terminates the DSL signal. It could consist of DSLAM in the central office, or remote DSLAM, or a Remote Access Multiplexer (RAM). Access node is the first point in the network where traffic on multiple DSL lines will be aggregated onto a single network. The NAS performs multiple functions in the network.

The NAS is the aggregation point for the subscriber traffic. It provides aggregation capabilities (e.g. IP, PPP, ATM) between the Regional/Access Network and the NSP or ASP. These include traditional ATM-based offerings and newer, more native IP-based services. This includes support for Point-to-Point Protocol over ATM (PPPoA) and PPP over Ethernet (PPPoE), as well as direct IP services encapsulated over an appropriate layer 2 transport.

Beyond aggregation, NAS is also the injection point for policy management and IP QoS in the Regional/Access Networks. In order to allow IP QoS support over an existing non-IP-aware layer 2 access network without using multiple layer 2 QoS classes, a mechanism based on hierarchical scheduling is used. This mechanism defined in [TR‑059] (Anschutz, T., “DSL Forum TR-059, DSL Evolution - Architecture Requirements for the Support of QoS-Enabled IP Services,” September 2003.), preserves IP QoS over the ATM network between the NAS and the RGs by carefully controlling downstream traffic in the NAS, so that significant queuing and congestion does not occur further down the ATM network. This is achieved by using a diffserv-aware hierarchical scheduler in the NAS that will account for downstream trunk bandwidths and DSL synch rates.

[ANCP‑FRAMEWORK] (Ooghe, S., Voigt, N., Platnic, M., Haag, T., and S. Wadhwa, “Framework and Requirements for an Access Node Control Mechanism in Broadband Multi-Service Networks,” February 2009.) provides detailed definition and functions of each network element in the broadband reference architecture.

     Access                   Customer
                       <--- Aggregation -->  <------- Premises ------->
                              Network                   Network

                       +------------------+ +--------------------------+
   +---------+   +---+ | +-----+ +------+ |-|+-----+ +---+ +---------+ |
NSP|         | +-|NAS|-| |ATM  |-|Access| | ||DSL  |-|HGW|-|Subscriber||
---+ Regional| | +---+ | +-----+ | Node | | ||Modem| +---+ |Devices   ||
   |Broadband| | +---+ |         +------+ | |+-----+       +----------+|
ASP|Network  |-+-|NAS| +--------------|---+ +--------------------------+
---+         | | +---+                |     +--------------------------+
   |         | | +---+                |     |+-----+ +---+ +----------+|
   +---------+ +-|NAS|                +-----|| DSL |-|HGW|-|Subscriber||
                 +---+                      ||Modem| +---+ |Devices   ||
                                            |+-----+       +----------+|
                                            +--------------------------+
 HGW   : Home Gateway
 NAS   : Network Access Server

3.2.  Ethernet-based broadband aggregation

The Ethernet aggregation network architecture builds on the Ethernet bridging/switching concepts defined in IEEE 802. The Ethernet aggregation network provides traffic aggregation, class of service distinction, and customer separation and traceability. VLAN tagging defined in IEEE 802.1Q and being enhanced by IEEE 802.1ad is used as standard virtualization mechanism in the Ethernet aggregation network. The aggregation devices are "provider edge bridges" defined in IEEE 802.ad. Stacked VLAN tags provide one possible way to create equivalent of "virtual paths" and "virtual circuits" in the aggregation network. The "outer" vlan could be used to create a form of "virtual path" between a given DSLAM and a given NAS. And "inner" VLAN tags to create a form of "virtual circuit" on a per DSL line basis. This is 1:1 VLAN allocation model. An alternative model is to bridge sessions from multiple subscribers behind a DSLAM into a single VLAN in the aggregation network. This is N:1 VLAN allocation model. Architectural and topological models of an Ethernet aggregation network in context of DSL aggregation are defined in [TR‑101] (Cohen et al, “Architecture & Transport: "Migration to Ethernet Based DSL Aggregation", DSL Forum TR-101,” 2005.)

4.  Access Node Control Protocol

4.1.  Overview

A dedicated control protocol between NAS and access nodes can facilitate "NAS managed" tight QOS control in the access network, simplified OSS infrastructure for service management, optimized multicast replication to enable video services over DSL, subscriber statistics retrieval on the NAS for accounting purposes, and fault isolation capability on the NAS for the underlying access technology. This dedicated control plane is referred to as "Access Node Control Protocol" (ANCP). This document specifies relevant extensions to GSMPv3 as defined [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.) to realize ANCP.

Following sections discuss the use of ANCP for implementing:

• Dynamic discovery of access topology by the NAS to provide tight QOS control in the access network.
• Pushing to the access-nodes, subscriber and service data retrieved by the NAS from an OSS system (e.g. radius server), to simplify OSS infrastructure for service management.
• Optimized, "NAS controlled and managed" multicast replication by access-nodes at L2 layer.
• NAS controlled, on-demand access-line test capability (rudimentary end-to-end OAM).

In addition to DSL, alternate broadband access technologies (e.g. Metro-Ethernet, Passive Optical Networking, WiMax) will have similar challenges to address, and could benefit from the same approach of a control plane between a NAS and an Access Node (e.g. OLT), providing a unified control and management architecture for multiple access technologies, hence facilitating migration from one to the other and/or parallel deployments.

GSMPv3 is an ideal fit for implementing ANCP. It is extensible and can be run over TCP/IP, which makes it possible to run over different access technologies.

4.2.  ANCP based Access Topology Discovery

4.2.1.  Goals

[TR‑059] (Anschutz, T., “DSL Forum TR-059, DSL Evolution - Architecture Requirements for the Support of QoS-Enabled IP Services,” September 2003.) discusses various queuing/scheduling mechanisms to avoid congestion in the access network while dealing with multiple flows with distinct QoS requirements. Such mechanisms require that the NAS gains knowledge about the topology of the access network, the various links being used and their respective net data rates. Some of the information required is somewhat dynamic in nature (e.g. DSL sync rate, and therefore also the net data rate), hence cannot come from a provisioning and/or inventory management OSS system. Some of the information varies less frequently (e.g. capacity of a DSLAM uplink), but nevertheless needs to be kept strictly in sync between the actual capacity of the uplink and the image the NAS has of it.

Following section describes ANCP messages that allow the Access Node (e.g. DSLAM) to communicate to the NAS, access network topology information and any corresponding updates.

Some of the parameters that can be communicated from the DSLAM to the NAS include DSL line state, actual upstream and downstream net data rates of a synchronized DSL link, maximum attainable upstream and downstream net data rates, interleaving delay etc. Topology discovery is specifically important in case the net data rate of the DSL line changes over time. The DSL net data rate may be different every time the DSL modem is turned on. Additionally, during the time the DSL modem is active, data rate changes can occur due to environmental conditions (the DSL line can get "out of sync" and can retrain to a lower value).

4.2.2.  Message Flow

When a DSL line initially comes up or resynchronizes to a different rate, the DSLAM generates and transmits a GSMP PORT UP EVENT message to the NAS. The extension field in the message carries the TLVs containing DSL line specific parameters. On a loss of signal on the DSL line, a GSMP PORT DOWN message is generated by the DSLAM to the NAS. In order to provide expected service level, NAS needs to learn the initial attributes of the DSL line before the subscriber can log in and access the provisioned services for the subscriber. Figure 2 (Message flow (ANCP mapping) for topology discovery) summarizes the interaction.

         <----- Port UP(EVENT Message)  <----- DSL
              (default line parameters)       Signal

1.  NAS ------------------ Access -----------  Home ----- Subscriber
                            Node              Gateway


         <----- Port UP (EVENT Message)  <----- DSL
               (updated line parameters)      Resynch
2.  NAS ------------------ Access ----------- Home ------ Subscriber
                            Node             Gateway

        <--- Port DOWN (EVENT Message) <---- DSL
                                           Loss of Signal

3.  NAS ----------------- Access ------------- Home ----- Subscriber
                           Node              Gateway

The Event message with PORT UP message type (80) is used for conveying DSL line attributes to the NAS. This message with relevant extensions is defined in section Section 5.4.2 (Topology Discovery Extensions).

4.3.  ANCP based Line Configuration

4.3.1.  Goals

Following dynamic discovery of access topology (identification of DSL line and its attributes) as assisted by the mechanism described in the previous section (topology discovery), the NAS could then query a subscriber management OSS system (e.g. RADIUS server) to retrieve subscriber authorization data (service profiles, aka user entitlement). Most of such service mechanisms are typically enforced by the NAS itself, but there are a few cases where it might be useful to push such service parameter to the DSLAM for local enforcement of a mechanism (e.g. DSL-related) on the corresponding subscriber line. One such example of a service parameter that can be pushed to the DSLAM for local enforcement is DSL "interleaving delay". Longer interleaving delay (and hence stringent error correction) is required for a video service to ensure better video "quality of experience", whereas for a VoIP service or for "shoot first" gaming service, a very short interleaving delay is more appropriate. Another relevant application is downloading per subscriber multicast channel entitlement information in IPTV applications where the DSLAM is performing IGMP snooping or IGMP proxy function. Using ANCP, the NAS could achieve the goal of pushing line configuration to the DSLAM by an interoperable and standardized protocol.

If a subscriber wants to choose a different service, it can require an OPEX intensive reconfiguration of the line via a network operator, possibly implying a business-to-business transaction between an ISP and an access provider. Using ANCP for line configuration from the NAS dramatically simplifies the OSS infrastructure for service management, allowing fully centralized subscriber-related service data (e.g. RADIUS server back-end) and avoiding complex cross-organization B2B interactions.

The best way to change line parameters would be by using profiles. These profiles (DSL profiles for different services) are pre-configured on the DSLAMs. The NAS can then indicate a reference to the right DSL profile via ANCP. Alternatively, discrete DSL parameters can also be conveyed by the NAS in ANCP.

4.3.2.  Message Flow

Triggered by topology information reporting a new DSL line or triggered by a subsequent user session establishment (PPP or DHCP), the NAS may send line configuration information (e.g. reference to a DSL profile) to the DSLAM using GSMP Port Management messages. The NAS may get such line configuration data from a policy server (e.g. RADIUS). Figure 3 (Message flow - ANCP mapping for Initial Line Configuration) summarizes the interaction.

                               1.DSL Signal
                                <-----------
        2. Port UP (EVENT Message)
       (Access Topology Discovery)
               <----------------
                           3. PPP/DHCP Session
                 <--------------------------------
  4. Authorization
 & Authentication
  <-------------------
                 Port Management Message
                 (Line Configuration)
               5. -------->
+----------+   +-----+     +-----+    +-------+    +-----------+
|Radius/AAA|---| NAS |-----| AN  |----|  Home |----|Subscriber |
|Policy    |   +-----+     +-----+    |Gateway|    +-----------+
|Server    |                          +-------+
+----------+

The NAS may update the line configuration due to a subscriber service change (e.g. triggered by the policy server). Figure 4 (Message flow - ANCP mapping for Updated Line Configuration) summarizes the interaction.

                                             1. PPP/DHCP Session
                      <------------------------------------------

    +-----------+                      2. Service On Demand
    |           |<-----------------------------------------------
    | Web portal|
    |  OSS etc  | 3.Change of   4.Port Management
    |           | Authorization   Message
    |Radius AAA | -------->     (Updated Line
    |  Policy   |                Config - New Profile)
    |           |          ------------->
    |           |    +------+     +-------+   +---------+  +----------+
    |           |----| NAS  |-----|  AN   |---|  Home   |--|Subscriber|
    |           |    +------+     +-------+   | Gateway |  +----------+
    +-----------+                             +---------+

The format of relevant extensions to port management message is defined in section Section 5.4.3 (Line Configuration Extensions). The line configuration models could be viewed as a form of delegation of authorization from the NAS to the DSLAM.

4.4.  ANCP based Transactional Multicast

4.4.1.  Goals

Typical IP multicast in access networks involves the NAS terminating user requests for receiving multicast channels via IGMP. The NAS authorizes the subscriber, and dynamically determines the multicast subscription rights for the subscriber. Based on the user's subscription, the NAS can replicate the same multicast stream to multiple subscribers. This leads to a waste of access bandwidth if multiple subscribers access network services via the same access-node (e.g. DSLAM). The amount of multicast replication is of the order of number of subscribers rather than the number of access-nodes. It is ideal for NAS to send a single copy of the multicast stream to a given access-node, and let the access-node perform multicast replication by layer2 means (e.g. ATM point-to-multipoint cell replication or Ethernet data-link bridging) for subscribers behind the access-node. However, operationally, NAS is the ideal choice to handle subscriber management functions (authentication, authorization, accounting and address management), multicast policies such as per-channel authorization, and complex multicast routing protocols. Therefore, some means is needed for the NAS to setup multicast replication state in the access-nodes. In ATM access networks, ANCP can be used by the NAS to setup P2MP cross-connects in the DSLAMs. Protocol support for this use-case is defined in section Section 5.4.5 (Multicast Extensions)

4.4.2.  Message Flow

The Multicast Replication Control Message is sent by the NAS to the AN with a directive to either join or leave one or more multicast flows. The AN will use a Multicast Status Message when conveying the outcome of the directive. The message flows in Figure 5 (NAS-Controlled Multicast Replication) illustrates the behavior of the AN in case of receiving a Multicast Replication Control Message.

+----------+    +-------+     +-----+        ANCP          +-----+
|Subscriber|    | Home  |     | AN  |<-------------------->| NAS |
+----------+    |Gateway|     +-----+                      +-----+
      |         +-------+         |                           |
      |            |              | Multicast-Replication-Crl |
      |            |              |(Target,add, Flowi..Flowj) |
      |            |              |<--------------------------|
      |       Mcast Flow 1        |                           |
      |<==========================+                           |
      |            |              |     Multicast-Status      |
      |            |              |-------------------------->|
      |            |              |                           |
      |            |              | Multicast-Replication-Crl |
      |            |              |(Target,delete,Flowi.Flowj)|
      |            |              |<--------------------------|
      |            |              |                           |
      |  <Stop Replication of     X                           |
      |            Mcast Flow 1>  |     Multicast-Status      |
      |            |              |-------------------------->|

4.5.  ANCP based OAM

In a mixed Ethernet and ATM access network (including the local loop), it is desirable to provide similar mechanisms for connectivity checks and fault isolation, as those used in an ATM based architecture. This can be achieved using an ANCP based mechanism until end-to-end Ethernet OAM mechanisms are more widely implemented in various network elements.

A simple solution based on ANCP can provide NAS with an access-line test capability and to some extent fault isolation. Controlled by a local management interface the NAS can use an ANCP operation to trigger the access-node to perform a loopback test on the local-loop (between the access-node and the CPE). The access-node can respond via another ANCP operation the result of the triggered loopback test. In case of ATM based local-loop the ANCP operation can trigger the access-node to generate ATM (F4/F5) loopback cells on the local loop. In case of Ethernet, the access-node can trigger an Ethernet loopback message(per EFM OAM) on the local-loop.

4.5.1.  Message Flow

"Port Management" message can be used by the NAS to request access node to trigger a "remote loopback" test on the local loop. The result of the loopback test can be asynchronously conveyed by the access node to the NAS in a "Port Management" response message. The format of relevant extensions to port management message is defined in section The format of relevant extensions to port management message is defined in section Section 5.4.4 (OAM Extensions). Figure 6 (Message Flow: ANCP based OAM) summarizes the interaction.

                 Port Management Message
                 (Remote Loopback          ATM loopback
                  Trigger Request)         OR EFM Loopback
               1.  ---------------->     2. --------->
                                            <--------+
+-------------+    +-----+       +-------+           +----------------+
|Radius/AAA   |----|NAS  |-------| DSLAM |-----------|    CPE         |
|Policy Server|    +-----+       +-------+           | (DSL Modem +   |
+-------------+                                      |Routing Gateway)|
                                                     +----------------+
                    3. <---------------
                    Port Management Message
               (Remote Loopback Test Response)

5.  Access Node Control Protocol (ANCP)

ANCP uses a subset of GSMPv3 messages described in [RFC3292] to implement currently defined use-cases. GSMPv3 general message format, used by all GSMP messages other than adjacency protocol messages, is defined in section 3.1.1 of GSMPv3 [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.). ANCP modifies this base GSMPv3 message format. The modified GSMPv3 message format is defined as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Vers  |  Sub  | Message Type  | Result|        Code           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Partition ID  |            Transaction Identifier             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |I|      SubMessage Number      |           Length              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                          Message Payload                      ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The 8-bit version field in the base GSMPv3 message header is split into two 4 bit fields for carrying the version and a sub-version of the GSMP protocol. ANCP uses version 3 and sub-version 1 of the GSMP protocol. An ANCP implementation SHOULD always set the version field to 3, and the sub-version field to 1. The Result field in the message header has been modified to be 4 bits long, and the Code field to be 12 bits long.

Version:

The version number of the GSMP protocol being used in this session. ANCP uses version 3.

Sub-Version:

The sub-version number of the GSMP protocol being used in this session. ANCP uses sub-version 1 of the GSMP protocol.

Result:

The Result field derived from GSMP [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.) has the following codes:

Ignore:

Res = 0x00 – Ignore this field on receipt and follow the procedures specified for the received message type.

Nack:

Res = 0x01 – Result code indicating that no response is expected to the message other than in cases of failure caused during the processing of the message contents or that of the contained directive(s).

AckAll:

Res = 0x02 – Result code indicating that a response to the message is requested in all cases. It is specifically intended to be used in some cases for Request messages only, and is not to be used in Event messages.

Success:

Res = 0x03 – Set by receiver to indicate successful execution of all directives in the corresponding Request message.

Failure:

Res = 0x4 – Set by receiver in the Response message if one or more directives in the corresponding Request message fails.

Message-Type:

The GSMP and ANCP message type.

Code:

This field gives further information concerning the result in a response message. It is mostly used to pass an error code in a failure response but can also be used to give further information in a success response message or an event message. In a request message, the code field is not used and is set to zero. In an adjacency protocol message, the Code field is used to determine the function of the message.

Partition ID:

This field is a 8 bit number which signifies a partition on the AN. [ TBD How AN and NAS agree on the partition numbers. Possible options:

1 - The partition ID could be configured on the AN and learnt by NAS in the adjacency message;

2 - The partition ID could be statically configured on the NAS as part of configuring the neighbor information.]

Transaction ID:

24-bit field set by the sender of a Request message to associate a Response message with the original Request message. The receiver of a Request message reflects the transaction ID from the Request message in the corresponding Response message. For event messages, the transaction identifier SHOULD be set to zero. The Transaction Identifier is not used, and the field is not present, in the adjacency protocol. The specific use of transaction ID as applicable to multicast use case is defined in Section 5.4.5 (Multicast Extensions)

I flag:

An ANCP implementation SHOULD set "I" and subMessage fields to 1 to signify no fragmentation.

Length:

Length of the GSMP message including its header fields and defined GSMP message body.

Additional General Message Information:

• Any field in a GSMP message that is unused or defined as "reserved" MUST be set to zero by the sender and ignored by the receiver;
• Flags that are undefined will be designated as: x: reserved.

Following are the relevant GSMPv3 messages defined in [RFC3292], that are currently used by ANCP. Other than the message types explicitly listed below, no other GSMPv3 messages are used by ANCP currently.

• Event Messages
  • Port UP Message
  • Port DOWN Message
  These messages are used by ANCP topology discovery use-case.
• Port Management Messages
  • These messages are used by ANCP "line configuration" use-case and ANCP OAM use-case.
• Adjacency Protocol Messages
  • These messages are used to bring up a protocol adjacency between a NAS and an AN.

ANCP modifies and extends few basic GSMPv3 procedures. These modifications and extensions are summarized below, and described in more detail in the succeeding sections.

• ANCP provides support for a capability negotiation mechanism between ANCP peers by extending the GSMPv3 adjacency protocol. This mechanism and corresponding adjacency message extensions are defined in section Section 5.3 (Capability negotiation)
• TCP connection establishment procedure in ANCP deviates slightly from the connection establishment in GSMPv3 as specified in [RFC3293] (Worster, T., Doria, A., and and J. Buerkle, “General Switch Management Protocol (GSMP) Packet Encapsulations for Asynchronous Transfer Mode (ATM), Ethernet and Transmission Control Protocol (TCP),” June 2002.). This is described in section Section 5.1 (ANCP/TCP connection establishment)
• ANCP makes GSMPv3 messages extensible and flexible by adding a general "extension block" to the end of the relevant GSMPv3 messages. The "extension block" contains a TLV structure to carry information relevant to each ANCP use-case. The format of the "extension block" is defined in section Section 5.4.1.1 (Extension TLV).

5.1.  ANCP/TCP connection establishment

ANCP will use TCP for exchanging protocol messages [RFC3293] (Worster, T., Doria, A., and and J. Buerkle, “General Switch Management Protocol (GSMP) Packet Encapsulations for Asynchronous Transfer Mode (ATM), Ethernet and Transmission Control Protocol (TCP),” June 2002.). defines the GSMP message encapsulation for TCP. The TCP session is initiated from the DSLAM (access node) to the NAS (controller). This is necessary to avoid static provisioning on the NAS for all the DSLAMs that are being served by the NAS. It is easier to configure a given DSLAM with the single IP address of the NAS that serves the DSLAM. This is a deviation from [RFC3293] (Worster, T., Doria, A., and and J. Buerkle, “General Switch Management Protocol (GSMP) Packet Encapsulations for Asynchronous Transfer Mode (ATM), Ethernet and Transmission Control Protocol (TCP),” June 2002.) which indicates that the controller initiates the TCP connection to the switch.

When GSMP messages are sent over a TCP connection a four-byte TLV header field is prepended to the GSMP message to provide delineation of GSMP messages within the TCP stream.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |        Type (0x88-0C)         |           Length              |
   |-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                         GSMP Message                          ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type

This 2-byte field indicates the type code of the following message. The type code for GSMP messages is 0x88-0C (i.e., the same as GSMP's Ethertype).

Length

This 2-byte unsigned integer indicates the total length of the GSMP message only. It does not include the 4-byte TLV header.

NAS listens for incoming connections from the access nodes. Port 6068 is used for TCP connection. Adjacency protocol messages, which are used to synchronize the NAS and access-nodes and maintain handshakes, are sent after the TCP connection is established. ANCP messages other than adjacency protocol messages may be sent only after the adjacency protocol has achieved synchronization.

In the case of ATM access, a separate PVC (control channel) capable of transporting IP would be configured between NAS and the DSLAM for ANCP messages.

In case of an Ethernet access/aggregation network, a typical practice is to send the Access Node Control Protocol messages over a dedicated Ethernet Virtual LAN (VLAN) using a separate VLAN identifier (VLAN ID).

5.2.  ANCP Connection keep-alive

GSMPv3 defines an adjacency protocol. The adjacency protocol is used to synchronize states across the link, to negotiate which version of the GSMP protocol to use, to discover the identity of the entity at the other end of a link, and to detect when it changes. GSMP is a hard state protocol. It is therefore important to detect loss of contact between switch and controller, and to detect any change of identity of switch or controller. No protocol messages other than those of the adjacency protocol may be sent across the link until the adjacency protocol has achieved synchronization. There are no changes to the base GSMP adjacency protocol for implementing ANCP.

The NAS will set the M-flag in the SYN message (signifying it is the master). Once the adjacency is established, periodic adjacency messages (type ACK) are exchanged. The default ACK interval as advertised in the adjacency messages is 10 sec for ANCP. It SHOULD be configurable and is an implementation choice. It is recommended that both ends specify the same timer value. However, it is not necessary for the timer values to match.

The GSMP adjacency message defined in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.) is extended for ANCP and is shown in section 5.3 immediately following this section. The 8-bit "version" field in the adjacency protocol messages is modified to carry the version and sub-version of the GSMP protocol for version negotiation. ANCP uses version 3 and sub-version 1 of GSMP protocol. The semantics and suggested values for Code, "Sender Name", "Receiver Name", "Sender Instance", and "Receiver Instance" fields are as defined in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.). The "Sender Port", and "Receiver Port" should be set to 0 by both ends. The pType field should be set to 0. The pFlag should be set to 1.

If the adjacency times out on either end, due to not receiving an adjacency message for a duration of (3 * Timer value), where the timer value is specified in the adjacency message, all the state received from the ANCP neighbor should be cleaned up, and the TCP connection should be closed. The NAS would continue to listen for new connection requests. The DSLAM will try to re-establish the TCP connection and both sides will attempt to re-establish the adjacency.

The handling defined above will need some modifications when ANCP graceful restart procedures are defined. These procedures will be defined in a separate draft.

5.3.  Capability negotiation

The adjacency message as defined in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.) is extended to carry technology specific "Capability TLVs". Both the NAS and the access node will advertise supported capabilities in the originated adjacency messages. If a received adjacency message indicates absence of support for a capability that is supported by the receiving device, it will turn off the capability locally and will send an updated adjacency message with the capability turned off to match the received capability set. This process will eventually result in both sides agreeing on the minimal set of supported capabilities. The adjacency will not come up unless the capabilities advertised by the controller and the controlled device match.

After initial synchronization, if at anytime a capability mismatch is detected, the adjacency will be brought down (RSTACK will be generated by the device detecting the mismatch), and synchronization will be re-attempted.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Ver |  Sub  | Message Type  |     Timer     |M|     Code    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                          Sender Name                          |
   +                               +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                               |                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               +
   |                         Receiver Name                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                          Sender Port                          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         Receiver Port                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PType | PFlag |               Sender Instance                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Partition ID  |              Receiver Instance                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Tech Type     | # of TLVs     | Total Length                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                   Capability TLVs                             ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The format of capability TLV is:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Capability Type         |   Capability Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                                                               ~
   ~                   Capability Data                             ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The Tech Type field type indicates the technology to which the capability extension applies. For access node control in case of DSL networks, new type "DSL" is proposed. The value for this field is 0x05. This is the first available value in the range that is not currently allocated. It will need to be reserved with IANA.

Capability length is the number of actual bytes contained in the value portion of the TLV. The TLV is padded to a 4-octet alignment. Therefore, a TLV with no data will contain a zero in the length field (if capability data is three octets, the length field will contain a three, but the size of the actual TLV is eight octets). Capability data field can be empty if the capability is just a boolean. In case the capability is a boolean, it is inferred from the presence of the TLV (with no data).

Capability data provides the flexibility to advertise more than mere presence or absence of a capability. Capability types can be registered with IANA. Following capabilities are defined for ANCP as applied to DSL access:

1. Capability Type : Dynamic-Topology-Discovery = 0x01

   Length (in bytes) : 0

   Capability Data : NULL

2. Capability Type : Line-Configuration = 0x02

   Length (in bytes) : 0

   Capability Data : NULL

3. Capability Type : Transactional-Multicast = 0x03 (controller i.e. NAS terminates IGMP messages from subscribers, and via l2 control protocol, signals state to the access-nodes (e.g. DSLAMs) to enable layer2 replication of multicast streams. In ATM access network this implies that NAS instructs the access-node to setup a P2MP cross-connect. The details of this will be covered in a separate ID.

   Length (in bytes) : 0

   Capability Data : NULL

4. Capability Type : OAM = 0x04

   Length (in bytes) : 0

   Capability Data : NULL

5.4.  GSMP Message Extensions for Access Node Control

5.4.1.  General Extensions

Extensions to GSMP messages for various use-cases of "Access Node Control" mechanism are defined in sections Section 5.4.2 (Topology Discovery Extensions) to Section 5.4.5 (Multicast Extensions). However, sub-sections Section 5.4.1.1 (Extension TLV) below define extensions to GSMP that have general applicability.

5.4.1.1.  Extension TLV

In order to provide flexibility and extensibility certain GSMP messages such as "PORT MANAGEMENT" and "EVENT" messages defined in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.) have been modified to include an extension block that follows a TLV structure. Individual messages in the following sections describe the usage and format of the extension block.

All Extension TLVs will be designated as follow:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|x|x|x|x|x|x|x|x| Message Type  |   Tech Type   | Block Length  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
~                         Extension Value                       ~
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

x: Reserved Flags

These are generally used by specific messages and will be defined in those messages.

Message Type

An 8-bit field corresponding to the message type where the extension block is used.

Tech Type

An 8-bit field indicating the applicable technology type value. The Message Type plus the Tech Value uniquely define a single Extension Type and can be treated as a single 16 bit extension type. "Tech Type" value of 0x05 SHOULD be used by ANCP for DSL technology.

0x00 Extension block not in use.

0x01 – 0x04 Already in use by various technologies

0x05 DSL

0x06 - 0xFE Reserved

0xFF Base Specification Use

Block Length

A 8-bit field indicating the length of the Extension Value field in bytes. When the Tech Type = 0x00, the length value MUST be set to 0.

Extension Value

A variable length field that is an integer number of 32 bit words long. The Extension Value field is interpreted according to the specific definitions provided by the messages in the following sections..

5.4.2.  Topology Discovery Extensions

The GSMP Event message with PORT UP message type (80) is used for conveying DSL line attributes to the NAS. The message SHOULD be generated when a line first comes UP, or any of the attributes of the line change e.g. the line re-trains to a different rate or one or more of the configured line attributes are administratively modified. Also, when the ANCP session first comes up, the DSLAM SHOULD transmit a PORT UP message to the NAS for each line that is up. When a DSL line goes down (idle or silent), the DSLAM SHOULD transmit an Event message with PORT DOWN message type (81) to the NAS. It is recommended that the DSLAMs use a dampening mechanism per DSL line to control the rate of state changes per DSL line, communicated to the NAS.

Not all the fields in GSMP Event message are applicable to ANCP. The fields that are not applicable MUST be set to zero by the ANCP sender and ignored by the ANCP receiver. The fields in the PORT UP and PORT DOWN messages to be set by the ANCP sender, and corresponding handling by the ANCP receiver is described below.

The version field MUST be set to 3, and the sub field MUST be set to 1. As defined in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.), the one byte Message Type field MUST be set to 80 for PORT UP Event message, and to 81 for PORT DOWN Event Message. The 8 bit Code field MUST be set to 0. The 4 bit Result field MUST be set to 0 (signifying Ignore.) If a PORT UP message with a Result field set to 0 is received by the NAS and the NAS is able to process the message correctly, the NAS MUST NOT generate any ANCP message in response to the PORT UP. If the PORT UP message received cannot be processed correctly by the NAS (e.g. the message is malformed) the NAS MAY respond with an ANCP Error Message (TBD) containing the reason of the failure. The 24-bit Transaction Identifier field MUST be set to 0. The "I" bit and the SubMessage field MUST be set to 1 to signify no fragmentation. The Length field is two bytes and MUST contain the length of the message (including header and the payload) in bytes.

The "Port" field, "Port Session Number" field and "Event Sequence Number" field are 4 bytes each, and MUST be set to 0 by the ANCP sender. LABEL field in event messages is defined as a TLV in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.). ANCP does NOT use the Label TLV. In both PORT UP and PORT DOWN event messages an ANCP sender MUST treat the Label field, immediately following the "Event Sequence Number" field, as a fixed 8 byte field, and MUST set these 8 bytes to 0. The receiver MUST NOT interpret the LABEL field as a TLV and MUST ignore the 8 bytes immediately following the "Event Sequence Number" field. In future versions of ANCP, if necessary, the un-used fields in GSMP Event message, which do not have ANCP specific semantics, can be used partially or completely, by re-naming appropriately, and associating valid semantics with these fields.

The Tech Type field is extended with new type "DSL". The value for this field is 0x05.

In case of bonded copper loops to the customer premise (as per DSL multi-pair bonding described by [G.988.1] (, “ITU-T recommendation G.998.1, ATM-based multi-pair bonding,” 2005.) and [G.988.2] (, “ITU-T recommendation G.998.2, Ethernet-based multi-pair bonding,,” 2005.)), the DSLAM MUST report the aggregate net data rate and other attributes for the "DSL bonded circuit" (represented as a single logical port) to the NAS in a PORT UP message. Any change in the aggregate net data rate of the "DSL bonded circuit" (due to a change in net data rate of individual constituent DSL lines or due to change in state of the individual constituent DSL lines) MUST be reported by the DSLAM to the NAS in a PORT UP message. The DSLAM MUST also report the "aggregate" state of the "DSL bonded circuit" to the NAS via PORT UP and PORT DOWN messages.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers  |  Sub  | Message Type  | Result|        Code           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID  |            Transaction Identifier             |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I|      SubMessage Number      |           Length              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                             Port                              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                      Port Session Number                      |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                     Event Sequence Number                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
+                             Label                             +
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|x|x|x|x|x|x|x|x| Message Type  |   Tech Type   | Block Length  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
~                         Extension Value                       ~
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The format of the "Extension Value" field for Tech Type "DSL" is as follows :

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     # of TLVs               | Extension Block length (bytes)  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                            TLVs                               ~
     ~                                                               ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The "Extension Value" contains one or more TLVs to identify a DSL line and define its characteristics. A TLV can consist of multiple sub-TLVs. First 2 byte of the "Extension Value" contains the number of TLVs that follow. The next 2 bytes contain the total length of the TLVs carried in the extension block in bytes (existing "Block Length" field in the GSMP message is limited to 255 bytes and is not sufficient).

General format of a TLV is :

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         Type                  |          Length               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                            Value                              ~
     ~                                                               ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The value field in each TLV is padded to a 4-octet alignment. The Length field in each TLV contains the actual number of bytes in the TLV (not including the padding if present). If a TLV is not understood by the NAS, it is silently ignored. Currently defined types start from 0x01.

Following TLVs are currently defined:

1. Type (Access-Loop-Circuit-ID = 0x01): This is a mandatory TLV and contains an identifier of the subscriber's connection to the access node (i.e. "local loop"). The "local loop" can be ATM based or Ethernet based. The "Access Loop Circuit ID" has local significance at the access node. The exact usage on the NAS is beyond the scope of this document. The format used for "local loop" identification in ANCP messages MUST be identical to what is used by the access nodes in subscriber signaling messages when the access nodes act as "signaling relay agents" as outlined in [RFC3046] (Patrick, M., “DHCP Relay Agent Information Option,” January 2001.) and [TR‑101] (Cohen et al, “Architecture & Transport: "Migration to Ethernet Based DSL Aggregation", DSL Forum TR-101,” 2005.).

   Length : (up to 63 bytes)

   Value : ASCII string

   For an ATM based local loop the string consists of slot/port and VPI/VCI information corresponding to the subscriber's DSL connection. Default syntax for the string inserted by the access node as per [TR‑101] (Cohen et al, “Architecture & Transport: "Migration to Ethernet Based DSL Aggregation", DSL Forum TR-101,” 2005.) is:

   "Access-Node-Identifier atm slot/port:vpi.vci"

   The Access-Node-Identifier uniquely identifies the access node in the access network. The slot/port and VPI/VCI uniquely identifies the DSL line on the access node. Also, there is one to one correspondence between DSL line and the VC between the access node and the NAS.

   For local loop which is Ethernet based (and tagged), the string consists of slot/port and VLAN tag corresponding to the subscriber. Default syntax for the string inserted by the access node as per [TR‑101] (Cohen et al, “Architecture & Transport: "Migration to Ethernet Based DSL Aggregation", DSL Forum TR-101,” 2005.) is:

   "Access-Node-Identifier eth slot/port[:vlan-id]"

2. Type (Access-Loop-Remote-Id = 0x02): This is an optional TLV and contains an identifier to uniquely identify a user on a local loop on the access node. The exact usage on the NAS is out of scope of this document. It is desirable that the format used for the field is similar to what is used by the access nodes in subscriber signaling messages when the access nodes act as "signaling relay agents" as outlined in [RFC3046] (Patrick, M., “DHCP Relay Agent Information Option,” January 2001.) and [TR‑101] (Cohen et al, “Architecture & Transport: "Migration to Ethernet Based DSL Aggregation", DSL Forum TR-101,” 2005.).

   Length : (up to 63 bytes)

   Value : ASCII string

3. Type (Access-Aggregation-Circuit-ID-Binary = 0x06)

   Length : (8 bytes)

   Value : two 32 bit integers

   For ethernet access aggregation, where a per-subscriber (stacked) VLAN can be applied (1:1 model defined in [TR‑101] (Cohen et al, “Architecture & Transport: "Migration to Ethernet Based DSL Aggregation", DSL Forum TR-101,” 2005.)), the VLAN stack provides a convenient way to uniquely identify the DSL line. The outer VLAN is equivalent to virtual path between a DSLAM and the NAS and inner VLAN is equivalent to a virtual circuit on a per DSL line basis. In this scenario, any subscriber data received by the access node and transmitted out the uplink to the aggregation network will be tagged with the VLAN stack assigned by the access node

   This TLV can carry the VLAN tags assigned by the access node in the ANCP messages. The VLAN tags can uniquely identify the DSL line being referred to in the ANCP messages, assuming the VLAN tags are not in any way translated in the aggregation network and are unique across physical ports. Each 32 bit integer (least significant bits) contains a 12 bit VLAN identifier (which is part of the VLAN tag defined by IEEE 802.1Q).

   Also, in case of an ATM aggregation network, where the DSLAM is directly connected to the NAS (without an intermediate ATM switch), the two values can contain VPI and VCI on the DSLAM uplink (and can uniquely identify the DSL line on the DSLAM).

   This is optional.

4. Type (Access-Aggregation-Circuit-ID-ASCII = 0x03)

   Length : (up to 63 bytes)

   Value : ASCII string

   This field contains information pertaining to an uplink on the access node. For Ethernet access aggregation, assuming the access node assigns VLAN tags (1:1 model), typical format for the string is:

   "Access-Node-Identifier eth slot/port [:inner-vlan-id][:outer-vlan-id]"

   The slot/port corresponds to the ethernet uplink on the access node towards the NAS.

   For an ATM aggregation network, typical format for the string is:

   "Access-Node-Identifier atm slot/port:vpi.vci"

   This TLV allows the NAS to associate the information contained in the ANCP messages to the DSL line on the access node.

   If the access node inserts this string in the ANCP messages, when referring to local loop characteristics (e.g. DSL line in case of a DSLAM), then it should be able to map the information contained in the string uniquely to the local loop (e.g. DSL line).

   On the NAS, the information contained in this string can be used to derive an "aggregation network" facing construct (e.g. an IP interface) corresponding to the local loop (e.g. DSL line). The association could be based on "local configuration" on the NAS.

   The access node can also convey to the NAS, the characteristics (e.g. bandwidth) of the uplink on the access node. This TLV then serves the purpose of uniquely identifying the uplink whose characteristics are being defined. A separate set of sub-TLVs will be defined for the uplink characteristics (TBD).

   This TLV is optional.

5. Type (DSL Line Attributes = 0x04):

   Length : variable (up to 1024 bytes)

   Value : This is a mandatory TLV and consists of one or more Sub-TLVs corresponding to DSL line attributes. No sub-TLVs other than the "DSL type" and "DSL line state" SHOULD be included in a PORT DOWN message.

   The general format of the sub-TLVs is identical to the general TLV format. The value field in each sub-TLV is padded to a 4-octet alignment. The Length field in each sub-TLV contains the actual number of bytes in the TLV (not including the padding if present). Current defined sub-TLV types are start from 0x81.

   Following sub-TLVs are currently defined :

   • Type (DSL-Type = 0x91) : Defines the type of transmission system in use. This is a mandatory TLV.

     Length : (4 bytes)

     Value : (Transmission system : ADSL1 = 0x01, ADSL2 = 0x02, ADSL2+ = 0x03, VDSL1 = 0x04, VDSL2 = 0x05, SDSL = 0x06, UNKNOWN = 0x07).

   • Type (Actual-Net-Data-Upstream = 0x81): Actual upstream net data rate on a DSL line. This is a mandatory TLV.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Actual-Net-Data-Rate-Downstream = 0x82) : Actual downstream net data rate on a DSL line. This is a mandatory TLV.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Minimum-Net-Data-Rate-Upstream = 0x83) : Minimum net data rate desired by the operator. This is optional.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Minimum-Net-Data-Rate-Downstream = 0x84) : Minimum net data rate desired by the operator. This is optional.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Attainable-Net-Data-Rate-Upstream = 0x85) : Maximum net upstream rate that can be attained on the DSL line. This is an optional TLV.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Attainable-Net-Data-Rate-Downstream = 0x86) : Maximum net downstream rate that can be attained on the DSL line. This is an optional TLV.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Maximum-Net-Data-Rate-Upstream = 0x87) : Maximum net data rate desired by the operator. This is optional.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Maximum-Net-Data-Rate-Downstream = 0x88) : Maximum net data rate desired by the operator. This is optional.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Minimum-Net-Low-Power-Data-Rate-Upstream = 0x89) : Minimum net data rate desired by the operator in low power state. This is optional.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Minimum-Net-Low-Power-Data-Rate-Downstream = 0x8A) : Minimum net data rate desired by the operator in low power state. This is optional.

     Length : (4 bytes)

     Value : (Rate in Kb/sec)

   • Type (Maximum-Interleaving-Delay-Upstream = 0x8B) : maximum one way interleaving delay. This is optional.

     Length : (4 bytes)

     Value : (Time in msec)

   • Type (Actual-Interleaving-Delay-Upstream = 0x8C) : Value corresponding to the interleaver setting. This is optional.

     Length : (4 bytes)

     Value : (Time in msec)

   • Type (Maximum-Interleaving-Delay-Downstream = 0x8D) : maximum one way interleaving delay. This is optional.

     Length : (4 bytes)

     Value : (Time in msec)

   • Type (Actual-Interleaving-Delay-Downstream = 0x8E) : Value corresponding to the interleaver setting. This is optional.

     Length : (4 bytes)

     Value : (Time in msec)

   • Type (DSL line state = 0x8F) : The state of the DSL line. For PORT UP message, at this time, the TLV is optional (since the message type implicitly conveys the state of the line). For PORT DOWN, the TLV is mandatory, since it further communicates the state of the line as IDLE or SILENT.

     Length : (4 bytes)

     Value : { SHOWTIME = 0x01, IDLE = 0x02, SILENT = 0x03 }

   • Type (Access Loop Encapsulation = 0x90) : The data link protocol and, optionally the encapsulation overhead on the access loop. This is an optional TLV. However, when this TLV is present, the data link protocol MUST minimally be indicated. The encapsulation overhead can be optionally indicated.

     Length : (3 bytes)

     Value : The three bytes (most to least significant) and valid set of values for each byte are defined below.

     Data Link (1 byte): {ATM AAL5 = 0, ETHERNET = 1}

     Encaps 1 (1 byte): {

     NA = 0,

     Untagged Ethernet = 1,

     Single-tagged Ethernet = 2}

     Encaps 2 (1 byte):{

     NA = 0,

     PPPoA LLC = 1

     PPPoA NULL = 2,

     IPoA LLC = 3,

     IPoA NuLL = 4,

     Ethernet over AAL5 LLC with FCS = 5,

     Ethernet over AAL5 LLC without FCS = 6,

     Ethernet over AAL5 NULL with FCS = 7,

     Ethernet over AAL5 NULL without FCS = 8}

     If this TLV is present, the Data Link protocol MUST be indicated as defined above. However, the Access Node can choose to not convey the encapsulation on the access loop by specifying a value of 0 (NA) for the two encapsulation fields

5.4.3.  Line Configuration Extensions

The Port Management message format defined in [RFC3292] (Doria, A. and et all, “General Switch Management Protocol (GSMP) V3,” June 2002.) has been modified to contain an extension block (described above in section Section 5.4.1.1 (Extension TLV)) at the end of the message. Also, the original two byte Function field has been modified to contain one byte for the Function field indicating a specific action to be taken by the recipient of the message, and one byte for X-Function field, which could further qualify the action specified in the Function field. Any Function specific data MUST be carried in the extension block.

Not all the fields in GSMP Port Management message are applicable to ANCP. The fields that are not applicable MUST be set to zero by the ANCP sender and ignored by the ANCP receiver.

The NAS uses the extension block in the Port Management messages to convey service attributes of the DSL lines to the DSLAM. TLVs are defined for DSL line identification and service data for the DSL lines. Port number is set to 0 in the message. A new action type "Configure Connection Service Data" (value 0x8) is defined. The "Function" field is set to the action type. This action type indicates to the device being controlled (Access Node i.e. DSLAM) to apply service configuration data contained in the extension value (TLVs), to the DSL line (identified by one of the TLVs in the extension value). For the action type "Configure Connection Service Data", X-Function field MUST be set to 0. The Tech Type field is extended with new type "DSL". The value for this field is 0x05.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers  |  Sub  | Message Type  | Result|        Code           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Partition ID  |            Transaction Identifier             |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|I|      SubMessage Number      |           Length              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                             Port                              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                      Port Session Number                      |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                     Event Sequence Number                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|R|x|x|x|x|x|x|x|   Duration    |    Function   | X-Function    |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|           Event Flags         |        Flow Control Flags     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|x|x|x|x|x|x|x|x| Message Type  |   Tech Type   | Block Length  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
~                         Extension Value                       ~
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The format of the "Extension Value" field is as follows:

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     # of TLVs               | Extension Block length (bytes)  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                            TLVs                               ~
     ~                                                               ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The "Extension Value" field contains one or more TLVs containing DSL line identifier and desired service attributes of the the DSL line. First 2 byte of the "Extension Value" contains the number of TLVs that follow. The next 2 bytes contain the total length of the extension block in bytes (existing "Block Length" field in the GSMP message is limited to 255 bytes and is not sufficient).

General format of a TLV is:

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         Type                  |          Length               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                            Value                              ~
     ~                                                               ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

• Type (Access-Loop-Circuit-ID = 0x01) : defined in section Section 5.4.1 (General Extensions)
• Type (Access-Aggregation-Circuit-ID-Binary = 0x06): defined in section Section 5.4.1 (General Extensions)
• Type (Access-Aggregation-Circuit-ID-ASCII = 0x03): defined in section Section 5.4.1 (General Extensions)
• Type (Service-Profile-Name = 0x05): Reference to a pre-configured profile on the DSLAM that contains service specific data for the subscriber.

  Length : (up to 64 bytes)

  Value : ASCII string containing the profile name (NAS learns from a policy server after a subscriber is authorized).

  In future, more TLVs MAY be defined for individual service attributes of a DSL line (e.g. rates, interleaving delay, multicast channel entitlement access-list etc).

5.4.4.  OAM Extensions

GSMP "Port Management" message (type 32) SHOULD be used by the NAS to trigger access node to run a loopback test on the local loop. The message format is defined in section Section 5.4.2 (Topology Discovery Extensions). The version field SHOULD be set to 3 and sub-version field SHOULD be set to 1. The remaining fields in the GSMP header have standard semantics. The function type used in the request message SHOULD be set to "remote loopback" (type = 0x09). The port, "port session number", "event sequence number", duration, "event flags", "flow control flags" and code fields SHOULD all be set to 0. The result field SHOULD be set to "AckAll" to indicate requirement for the access node to send a success or failure response. The transaction ID SHOULD contain a sequence number inserted by the NAS in each request that it generates.

Not all the fields in GSMP Port Management message are applicable to ANCP. The fields that are not applicable MUST be set to zero by the ANCP sender and ignored by the ANCP receiver.

The extension field format is also defined above in section Section 5.4.2 (Topology Discovery Extensions). The extension value field can contain one or more TLVs including the access-line identifier on the DSLAM and OAM test characteristics desired by the NAS.

The TLV format is defined above in section Section 5.4.2 (Topology Discovery Extensions). The value field is padded to a 4-octet alignment. The Length field in each TLV contains the actual number of bytes in the TLV (not including the padding if present). If a TLV is not understood by the NAS, it is silently ignored. Depending upon the deployment scenario, the NAS may specify "Access Loop Circuit-ID" or the "Access Aggregation Circuit-ID") as defined in section Section 5.4.1 (General Extensions). Following TLVs can appear in this message:

• Type (Access-Loop-Circuit-ID = 0x01) : defined in section Section 5.4.1 (General Extensions)
• Type (Access-Aggregation-Circuit-ID-Binary = 0x06): defined in section Section 5.4.1 (General Extensions)
• Type (Access-Aggregation-Circuit-ID-ASCII = 0x03): defined in section Section 5.4.1 (General Extensions)
• Type (OAM-Loopback-Test-Parameters = 0x07): Parameters related to loopback test. This is an optional TLV. If this TLV is not present in the request message, the DSLAM SHOULD use locally determined default values for the test parameters.

  Length : (4 bytes)

  Value : two 1 byte numbers described below (listed in order of most to least significant). Thus, the 4 bytes consist of 1 byte of Count, followed by 1 byte of Timeout, followed by two pad bytes of zero.

  • Count (1 byte) : Number of loopback cells/messages that should be generated on the local loop as part of the loopback test. The NAS SHOULD restrict the "count" to be greater than 0 and less than or equal to 32. The DSLAM SHOULD discard the request for a loopback test, if the received test parameters contain an out of range value for the "count" field. The DSLAM MAY optionally send a failure response to the NAS with the code "invalid test parameter".
  • Timeout (1 byte) : Upper bound on the time in seconds that the NAS would wait for a response from the DSLAM. If the total time taken by the DSLAM to complete a test with requested parameters, exceeds the specified "timeout" value, it can choose to omit the generation of a response to the NAS. DSLAM SHOULD use a locally determined value for the "timeout", if the received value of the "timeout" parameter is 0.

• Type (Opaque-Data = 0x08) : This is an optional TLV. If present in the request message, the DSLAM SHOULD reflect it back in the response unmodified

  Length : (8 bytes)

  Value : Two 32 bit integers inserted by the NAS (not to be interpreted by the DSLAM, but just reflected back in the response).

The access node generates a success or failure response when it deems the loopback test to be complete. "Port Management" message (type 32) is used. The result field SHOULD be set to success or failure. The function type SHOULD be set to 0x09. The transaction ID SHOULD be copied from the sequence number contained in the corresponding request. The other parameters not explicitly defined here SHOULD be set as specified in the request message above. The code field SHOULD be set to a value in the range 0x500 to 0x5ff (to be reserved with IANA) to indicate the status of the executed test. The valid values defined are (can be extended in future):

0x500 : Specified access line does not exist

0x501 : Loopback test timed out

0x502 : Reserved

0x503 : DSL line status showtime

0x504 : DSL line status idle

0x505 : DSL line status silent

0x506 : DSL line status training

0x507 : DSL line integrity error

0x508 : DSLAM resource not available

0x509 : Invalid test parameter

The Extension value can contain one or more TLVs including the TLV to identify the access line on which the test was performed, and details from executing the test. The access line identifier SHOULD be identical to what was contained in the request. The relevant TLVs are:

• Type (Access-Loop-Circuit-ID = 0x01) : defined in section Section 5.4.1 (General Extensions)
• Type (Access-Aggregation-Circuit-ID-Binary = 0x06): defined in section Section 5.4.1 (General Extensions)
• Type (Access-Aggregation-Circuit-ID-ASCII = 0x03): defined in section Section 5.4.1 (General Extensions)
• Type (Opaque-Data = 0x08) : Data inserted by the NAS in the request reflected back by the DSLAM.

  Length : (up to 8 bytes)

  Value : Two 32 bit integers as received in the request (opaque to the DSLAM).

• Type (OAM-Loopback-Test-Response-String = 0x09)

  Length : (up to 128 bytes)

  Value : Suitably formatted ASCII string containing useful details about the test that the NAS will display for the operator, exactly as received from the DSLAM (no manipulation/interpretation by the NAS). This is an optional TLV, but it is strongly recommended, that in case of ATM based local loop, the DSLAM at the very least indicates via this TLV, the total loopback cells generated and the total loopback cells successfully received as part of executing the requested loopback test.

5.4.5.  Multicast Extensions

The format of the ANCP Multicast message starts with the common GSMP header as in the case of the existing ANCP implementation. Following is the format of this header:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Vers  |  Sub  | Message Type  | Result|        Code           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Partition ID  |            Transaction Identifier             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |I|      SubMessage Number      |           Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      ~                          Message Payload                      ~
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The Result field takes one of the values defined in Section 5 (Access Node Control Protocol (ANCP)).

The Transaction Identifier field is used to distinguish between request messages and to associate a response message to a request. Applications that require such response correlation MUST set the Transaction Identifier to a value in the range (1, 2^24 – 1). When used in this manner, the Transaction Identifier sequencing MUST be maintained independently for each ANCP adjacency and per message type. Furthermore, it SHOULD be incremented linearly for each new message of the given type, cycling back to 1 after running the full range. Message types not requiring response message correlation SHOULD set the Transaction Id field to 0x0. In the event of an ANCP transport protocol failure, all pending ANCP messages destined to the disconnected recipient can be discarded until the transport is re- established following which the Transaction Identifier is re- initialized.

The value of the Transaction Identifier in a Response message MUST be set to that of the respective Request message. This allows the Requester to correlate the Response to the original Request. The Transaction Identifier is not used in ANCP adjacency messages. Also, other ANCP applications not requiring it SHOULD set the Transaction Identifier to 0x0 in their messages.

All TLVs within the ANCP message have to be 32 bit aligned, and when necessary padded with 0s to the 32 bit boundary. The padding is not reflected in the message length field.

5.4.5.1.  General well known TLVs

This section contains the definitions of three general well known TLVs. These TLVs are intended to be re-usable across different Multicast messages.

5.4.5.1.1.  Target TLV

The Target TLV (0x10) is intended to be a general well known TLV allowing the representation of different types of objects. Its use is not restricted to any specific Message Type.

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    TLV Type = Target          |        Target-TLV Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                         Target Info                           ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Target TLV:

TLV (0x10) indicating the type of target being addressed. Numbers TBC. Tentative 0x1000 for single Access-Port.

Target TLV Length:

Length in bytes of Target Info. Excludes TLV header

Target Info:

Target information as defined for each the given target. The field can consist of sub-TLVs.

In its simplest form, when targeting a single access line the Target-TLV will be set to a value of (0x10), and carry in its payload one or more sub-TLVs identifying the target. The following example illustrates the message format for a single port identified by an Access-Loop-Circuit-ID TLV (0x0001) that could be derived from a Port-UP message:

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    TLV Type = Target          |        Target-TLV Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Access-Loop-Circuit-ID=0x0001 |       Circuit-ID Length       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                    Access Loop Circuit ID                     ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

5.4.5.1.2.  Command TLV

The Command TLV (0x11) is intended to be a general well known TLV allowing the encapsulation of one or more command directives in a TLV oriented message. The semantics of the command are allowed to be specified for each message type, ie different message types that choose to carry the Command TLV are expected to define the meaning of the content of the payload, which could be re-used from those already defined elsewhere if appropriate.

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     TLV Type = Command        |       Command-TLV Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                         Command Info                          ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Additional sub-TLV Type   |   Additional sub-TLV Length   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                   Additional sub-TLV data                     ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Command TLV:

TLV (0x11) indicating the contents to be one or more command directives.

Command TLV Length:

Combined length in bytes of the data in Command Info and sub-TLV. Excludes the Command TLV header

Commad-Info:

Command information as defined for each message type. The field can consist of sub-TLVs.

Additional sub-TLV:

Additional sub-TLVs can be present in a command TLV. Any such sub-TLVs must directly follow each command.

Additional sub-TLV Length:

Number of actual bytes contained in the value portion of each additional sub-TLV

5.4.5.1.3.  Status-Info TLV

The Status-info-TLV is intended to be a general well known TLV used to convey the status code regarding commands and/or requests. The format of the Status-Info-TLV (0x012) is shown below.

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    TLV Type = Status-info     |        Status TLV Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Result Code   |  Cmnd Nmbr    |      Error Message Length     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Error Message (aligned to 4 bytes length)              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |           sub-TLVs...                                         |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

Status-info TLV:

TLV (0x12) conveying the status or error response of a command

Status TLV Length:

Specifies the length in bytes of the Status Info TLV payload. Excludes the TLV header

Result Code:

Conveys the result code for the command or message, as defined by the application.

Cmnd Nmbr:

Contains the command number copied from the Request message. The value of 0 is used whenever the error is not specific to a command.

Error Message Length:

Contains the length of an optional error message or 0 if none.

TLVs:

This field is of indeterminate length, and contains zero or more of the TLVs associated with the Status-info-TLV.

5.4.5.2.  Multicast Replication Control Message

The Multicast Replication Control Message Type 0x90 (TBC) is sent by the NAS to the AN with a directive to either add (join) or delete (leave) one or more multicast flows on a target object identified in the content of the message. When a response is needed an AN MUST use the Multicast Status message to convey the outcome of the directive; this message type is covered in Section 5.4.5.3 (Multicast Status Message).

The sender of a Multicast Replication Control message MUST set the Result field to 0x00 meaning "Ignore". The sender MUST populate the ANCP Transaction Identifier field with a distinct non-zero, linearly incrementing value for each Request per adjacency, as described in Section 5.4.5 (Multicast Extensions) .

The ANCP Multicast Replication Control message payload contains the following TLVs:

      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Type = Target TLV      |     Length of Target-Info     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                      Value = Target-Info                      ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |      Type = Command TLV       |    Length of Command Info     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                      Value = Command Info                     ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Target:

See Section 5.4.5.1.1 (Target TLV). The Target TLV (0x10) can only feature once in a Multicast Replication Control Message. Only one such TLV is allowed in this message type.

Length of Target-Info:

See Section 5.4.5.1.1 (Target TLV)

Target Info:

See Section 5.4.5.1.1 (Target TLV)

Command TLV:

The Command TLV (0x11) contains the multicast flow directive(s) for the target and any additional parameters passed via sub-TLVs. See Section 5.4.5.1.2 ( Command TLV)

Length of Command Info:

Includes sub-TLVs. See Section 5.4.5.1.2 ( Command TLV)

Command Info:

Command information as defined in section Section 5.4.5.1.2 ( Command TLV).

The contents of the Command TLV for the Multicast Replication Control Message are defined to be as follows:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Command Code  |R O M   Flags  |         Command Length        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Addr Family   | Encoding Type |  Multicast Source Address     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++++++++++++|
     | Addr Family   | Encoding Type |  Multicast Flow Address       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+++++++++++-+

Command Code:

Command directive: 0x01 – Add; 0x02 – Delete; 0x03 – Delete All.

Command Length:

Length in bytes of each Command including multicast flow address, but excluding the Command Code header and flags.

Flags:

8 bit General purpose Flag field. Currently the following flags are defined:

R -

Resource Admitted Flag. Set to 1 in an add command to indicate that the flow resources have been reserved by admission control, 0 otherwise. Not used in delete command.

O -

Flow Accounting. When set in add command indicates that byte accounting for the flow is to commence.

M -

When set indicates that multicast flow is SSM and the address-family-element set MUST specify the source and group addresses. When not set indicates that multicast flow is ASM and address-family-element MUST specify the group address, and the Source Address field is to be omitted.

Address Family:

The address family used

The unicast source address/mask follows the format defined in [IANAAEA] (, “http://www.iana.org/assignments/address-family-numbers,” 2005.)

Encoded-Unicast-address: Takes the following format:
0                   1                   2                   3
  0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 | Addr Family   | Encoding Type |     Unicast Address           |
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+++++++++++++

Encoded-Unicast-address: Takes the following format:
0                   1                   2                   3
  0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 | Addr Family   | Encoding Type |     Unicast Address           |
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+++++++++++++

Encoding Type:

The type of encoding used within a specific Address Family. The value `0' is reserved for this field, and represents the native encoding of the Address Family.

The address as represented by the given Address Family and Encoding Type.

Address:

The address as represented by the given Address Family and Encoding Type.

The padding will be done after both addresses so that it is 32-bit aligned. As an example for IPv4:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | CmdCode=0x01  |0 0 1   Flags  |         Command Length        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | AddrFamily 0x1| Enc Type  0x0 |    Src Address first 2 bytes  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Src Address last 2 bytes      | AddrFamily 0x1|  Enc Type 0x0 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   Multicast Address (4 bytes)                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

In the above example, no padding is required.

A received Multicast Replication Control Message containing an unrecognized Target TLV MUST be communicated to the sender as an error in a Multicast Status Message indicating the "Unrecognised port Type - 0x04" error. The reception of a Multicast Replication Control Message, or any ANCP message, that is found to have mandatory TLVs missing is to be addressed as part of a ANCP base protocol mechanism yet to be defined.

Each Multicast Replication Control Message may contain one or more command directives, each encapsulated by their own Command TLVs. The sender MUST use separate Command TLVs for each distinct multicast flow. When successive commands relate to a given Target and flow, the state of features controlled or affected by flags as well as by optional attributes received in the Multicast Replication Control message, are to be interpreted as replacing any such previous state for that port and flow. As an example, successive Multicast Replication Control messages containing add commands for a given port and flow, but differing in the accounting flag setting should be interpreted as affecting the state of the accounting feature.

The recipient of a Multicast Replication Control message is to run an implicit directive numbering across the multiple directives in the message. The numbering is to start from 0x01 for each directive in a given ANCP Multicast Replication Control message, and be restarted for subsequent messages. The recipient MUST process the directives in the order of reception, and use the derived directive number in any response messages, besides the Transaction ID.

The processing/execution of multiple directives contained in a single Multicast Control message MUST be interrupted at the first error, and the remaining commands in the Multicast Replication Control message discarded. In such a case a Multicast Status message MUST be sent indicating the command number that resulted in the error along with the error code.

When the strict sequenced processing of the directives in a single Multicast Control message is not required the directives MUST be distributed across separate Multicast Replication Control messages.

Each command directive is equipped with an 8-bit Flags field that allows specification of Multicast ASM or SSM modes of operation, and an indication of other features or conditions attached to this command (e.g. To enable accounting for the flow, etc). Unassigned flags are reserved for future use, and could in the future be subject of the capability negotiation. When receiving a Multicast Replication Control Message containing an unrecognized Flag set (to 1), a recipient MUST interpret it as an error, and generate an Multicast Status message indicating the error.

The multicast flow subject to the command is specified by means of one or two well known Address Family designators ([IANAAEA] (, “http://www.iana.org/assignments/address-family-numbers,” 2005.)), the IPv4-Address-Family (0x01) and the IPv6-Address-Family (0x02). When the M flag is set the two Address-Family tuples MUST be present in the strict order specifying the multicast flow source and group respectively. When the M flag is cleared only one Address-Family is allowed, specifying the multicast flow.

For future extensibility, each command may also have additional TLVs appended following the command and multicast flow information (referred to as “TLVs” in the message format above). Unrecognized TLVs SHOULD be silently discarded. The figure below is an example of a Multicast Replication Control message that would result in a swap from multicast SSM flows 192.0.2.1, 233.252.0.2, to 192.0.2.2, 233.252.0.3 on the Target identified by the “Access Loop Circuit ID”:

     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Type (0x88-0C)         |           Length              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Vers  |  Sub  |MessageType=90 | 0x02  |        Code           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Partition ID  |            Transaction Identifier = 0001      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |I|      SubMessage Number      |           Length              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Type = Target 0x1000   |        Target TLV Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Access-Loop-Circuit-ID 0x0001 |        Circuit-ID Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     ~                    Access Loop Circuit ID                     ~
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Type = Command TLV     |       Command-TLV Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Cmd Code=0x02 |0 0 1          |      Command Length           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | AddrFamily 01 | EncType 0x0  |  Mcast Source: 192.0.2.1       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | AddrFamily 01 | EncType 0x0  |  Mcast Flow : 233.252.0.2      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+--+
     |        Type = Command-TLV     |       Command-TLV Length      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Cmd Code=0x01 |0 0 1          |      Command Length           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | AddrFamily 01 | EncType 0x0   |  Mcast Source: 192.0.2.2      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | AddrFamily 01 | EncType 0x0   |  Mcast Flow: 233.252.0.3      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

5.4.5.3.  Multicast Status Message

The Multicast Status Message (Message Type 0x91 - TBC) is sent by the AN to the NAS in response to a Multicast Replication Control Message and its command directives. A Multicast Status message MUST use the same ANCP Transaction ID as that in the original Multicast Replication Control Message. The Success or Failure status is reported in the Result field of the ANCP header as described in Section 5.4.5 (Multicast Extensions).

A Multicast Status Message indicating Success SHOULD simply consist only of the base ANCP header with no body, however the message MAY contain one or more TLVs that are meant to communicate any relevant information to an application. The payload of a Multicast Status Message indicating Failure MUST contain an Status-Info TLV (0x12), as defined in Section 5.4.5.1.3 (Status-Info TLV), as its first TLV and SHOULD be followed by the Target TLV and Port-info. Other TLVs MAY be present. A Multicast Status message indicating Failure MUST be sent whenever a Multicast Control message cannot be fulfilled or results in an execution error. The Cmnd Nmbr parameter in the Status-Info TLV contained by the Multicast Status Message is to indicate the number of the command in the Multicast Replication Control Message that resulted in an error.

0x00 - Success

0x01 - Malformed message

0x02 - Command not supported

0x03 - Flag set but not supported

0x04 - Unrecognized Target

0x05 - Unsupported Address Family

0x06 - Malformed flow address

0x07 - No resources

0x08 - Unknown Target

0x09 - Target down

0x0a - Configuration error (such as Port not enabled for multicast)

0x0b - Multicast flow does not exist

0x0c - Unsupported address encoding

0x0d - Additional info needed to execute command (payload MAY contain an indication of the expected info)

0x0e - Multicast flow count exceeded

0x0f - M Flag set, but no IP Source address provided

0x10 - Transaction-id out of sequence

An example of a failure message for an invalid address, including the Target TLV for a 4 byte “Access Loop Circuit ID”, followed by TLV padding, is as follows:

     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Type (0x88-0C)         |           Length              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Vers  |  Sub  |MessageType=91 | 0x4   |        Code           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Partition ID  |            Transaction Identifier = 0001      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |I|      SubMessage Number      |           Length              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Status-info-TLV=0x12  |      Status-TLV-Length        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |  Result Code  |  Cmd Number   |    Error Message Length       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |           Error Message (padded to 4) if Length > 0           |
     +---------------------------------------------------------------+
     |     Target TLV=0x10           |        Target-Length          |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Access Loop ID type       |     Access-Loop ID  Length    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                            circuit ID                         |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

5.5.  ATM-specific considerations

The topology discovery and line configuration involve the DSL line attributes. For ATM based access networks, the DSL line on the DSLAM is identified by the port and PVP/PVC corresponding to the subscriber. The DSLAMs are connected to the NAS via an ATM access aggregation network. Since, the DSLAM (access-node) is not directly connected to the NAS, the NAS needs a mechanism to learn the DSL line identifier (more generally referred to as "Access Loop Circuit-ID") corresponding to a subscriber. The "Access loop circuit-ID" has no local significance on the NAS. The ANCP messages for topology discovery and line configuration carry opaque "Access loop Circuit-ID" which has only local significance on the DSLAMs.

The access loop circuit identifier can be carried as an ASCII string in the ANCP messages. This allows ANCP to be decoupled from the specifics of the underlying access technology being controlled. On the other hand, this requires a NAS mechanism by which such identifier can be correlated to the context of an "aggregation network" facing IP interface (corresponding to the subscriber) on the NAS. This would typically require local configuration of such IP interfaces, or of the underlying ATM interfaces.

5.6.  Ethernet-specific considerations

One possible way of approaching the use of Ethernet technology in the access aggregation network is to recreate the equivalent of Virtual Paths (VPs) and Virtual Circuits (VCs) by using stacked Virtual LAN tags. As an example, one could use an "outer" VLAN to create a form of "virtual path" between a given DSLAM and a given NAS. And then use "inner" VLAN tags to create a form of "virtual circuit" on a per DSL line basis. In this case, VLAN tags conveyed in topology discovery and line configuration messages will allow to uniquely identify the DSL line in a straightforward manner, assuming the VLAN tags are not translated in some way by the aggregation network, and are unique across physical ports.

However, some carriers do not wish to use this "connection oriented" approach. Therefore, an alternative model is to bridge sessions from multiple subscribers behind a DSLAM to a single VLAN in the aggregation network. This is the N:1 model. In this model, or in the case where user traffic is sent untagged, the access node needs to insert the exact identity of the DSL line in the topology discovery and line configuration messages, and then hve a mechanism by which this can be correlated to the context of an "aggregation network" facing IP interface (for the subscriber) on the NAS. This can either be based on local configuration on the NAS, or on the fact that such DSLAM (access node) typically inserts the "Access Loop Circuit ID" in subscriber signaling messages relayed to the NAS (i.e. DHCP or PPPoE discovery messages).

Section Section 5.4.1 (General Extensions) defines "Access Loop Circuit ID".

6.  IANA Considerations

This document defines the following additions to the GSMPv3 Message Type Name Space registry:

This document defines the following modification to the Global Switch Management Protocol version 3 (GSMPv3) Result Type Name Space registry:

This document defines the following addition to the GSMPv3 Message Function Name Space registry [editor's note GMSPv3 did not define a Name Space for Function even if RFC3292 defines values for function field]:

This document reserves the range 0x500 to 0x5ff of GSMPv3 Failure Response Message Name Space registry to indicate the status of the executed test for OAM use case described in Section 5.4.4 (OAM Extensions). The initial entries are as follows:

This document defines a new ANCP Tech Type Name Space registry. The initial entries are as follows:

This document defines a new ANCP Status-Info Result Code registry. The initial entries are as follows:

This document defines a new ANCP Command Code registry. The initial entries are as follows:

This document defines a new ANCP TLV Type registry. The initial entries are as follows:

This document defines a new ANCP Capability registry. The initial entries are as follows:

This document defines a new ANCP sub-TLV Type registry. The initial entries are as follows:

7.  Security Considerations

Security of the ANCP protocol is discussed in [ANCP‑SEC] (Moustafa, H., Tschofenig, T., and S. De Cnodder, “Security Threats and Security Requirements for the Access Node Control Protocol (ANCP),” March 2009.)

8.  Acknowledgements

The authors would like to thank everyone that has provided comments or inputs to this document. In particular, the authors acknowledge the inputs provided by Peter Arberg, Josef Froehler, Derek Harkness, Kim Hyldgaard, Sandy Ng, Robert Peschi, Michel Platnic, Tom Taylor and the work done by Philippe Champagne, Wojciech Dec and Stefaan De Cnodder regarding multicast extensions.

9.  References

9.1. Normative References

9.2. Informative References

Authors' Addresses