| Internet-Draft | Forward Search P2mP Path | January 2022 |
| Chen | Expires 14 July 2022 | [Page] |
This document presents a forward search procedure for computing a path for a Point-to-MultiPoint (P2MP) Traffic Engineering (TE) Label Switched Path (LSP) crossing a number of domains through using multiple Path Computation Elements (PCEs). In addition, extensions to the Path Computation Element Communication Protocol (PCEP) for supporting the forward search procedure are described.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 14 July 2022.¶
Copyright (c) 2022 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
RFC 4105 "Requirements for Inter-Area MPLS TE" lists the requirements for computing a shortest path for a TE LSP crossing multiple IGP areas; and RFC 4216 "MPLS Inter-Autonomous System (AS) TE Requirements" describes the requirements for computing a shortest path for a TE LSP crossing multiple ASes. RFC 5671 "Applicability of PCE to P2MP MPLS and GMPLS TE" examines the applicability of PCE to path computation for P2MP TE LSPs in MPLS and GMPLS networks.¶
This document presents a forward search procedure to address these requirements for computing a path for a P2MP TE LSP crossing domains through using multiple Path Computation Elements (PCEs).¶
The procedure is called "Forward Search Shortest P2MP LSP Path Crossing Domains" or FSPC for short. The major characteristics of this procedure for computing a path for a P2MP TE LSP from a source node to a number of destination nodes crossing multiple domains include the following three ones.¶
ABR: Area Border Router. Routers used to connect two IGP areas (areas in OSPF or levels in IS-IS).¶
ASBR: Autonomous System Border Router. Routers used to connect together ASes of the same or different service providers via one or more inter-AS links.¶
Boundary Node (BN): a boundary node is either an ABR in the context of inter-area Traffic Engineering or an ASBR in the context of inter-AS Traffic Engineering.¶
Entry BN of domain(n): a BN connecting domain(n-1) to domain(n) along the path found from the source node to the BN, where domain(n-1) is the previous hop domain of domain(n).¶
Exit BN of domain(n): a BN connecting domain(n) to domain(n+1) along the path found from the source node to the BN, where domain(n+1) is the next hop domain of domain(n).¶
Inter-area TE LSP: A TE LSP that crosses an IGP area boundary.¶
Inter-AS TE LSP: A TE LSP that crosses an AS boundary.¶
LSP: Label Switched Path.¶
LSR: Label Switching Router.¶
PCC: Path Computation Client. Any client application requesting a path computation to be performed by a Path Computation Element.¶
PCE: Path Computation Element. An entity (component, application, or network node) that is capable of computing a network path or route based on a network graph and applying computational constraints.¶
PCE(i) is a PCE with the scope of domain(i).¶
TED: Traffic Engineering Database.¶
This document uses terminologies defined in RFC5440.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC2119.¶
This section summarizes the requirements specific for computing a path for a Traffic Engineering (TE) LSP crossing multiple domains (areas or ASes). More requirements for Inter-Area and Inter-AS MPLS Traffic Engineering are described in RFC 4105 and RFC 4216.¶
A number of requirements specific for a solution to compute a path for a TE LSP crossing multiple domains is listed as follows:¶
This section gives an overview of the forward search path computation procedure (FSPC) to satisfy the requirements for computing a path for a P2MP TE LSP crossing multiple domains described above and describes the procedure in details.¶
Simply speaking, the idea of FSPC for computing a path for an MPLS TE P2MP LSP crossing multiple domains from a source node to a number of destination nodes includes:¶
Start from the source node and the source domain.¶
Consider the optimal path segment from the source node to every exit boundary and destination node of the source domain as a special link;¶
Consider the optimal path segment from an entry boundary node to every exit boundary node and destination node of a domain as a special link; and the optimal path segment is computed as needed.¶
The whole topology consisting of many domains can be considered as a special virtual topology, which contains those special links and the inter-domain links.¶
Compute a shortest path in this special topology from the source node to the multiple destination nodes using CSPF.¶
FSPC running at any PCE just grows the result path list/tree in the same way as normal CSPF on the special virtual topology. When the result path list/tree reaches all the destination nodes, the shortest path from the source node to the destination nodes is found and a PCRep message with the path is sent to the PCE/PCC that sends the PCReq message eventually.¶
Suppose that we have the following variables:¶
A current PCE named as CurrentPCE which is currently computing the path.¶
A candidate node list named as CandidateNodeList, which contains the nodes to each of which the temporary optimal path from the source node is currently found and satisfies a set of given constraints. Each node C in CandidateNodeList has the following information:¶
The flags include:¶
The nodes in CandidateNodeList are ordered by path cost.¶
Initially, CandidateNodeList contains a Source Node, with path cost 0, PCE responsible for the source domain, and flags with S bit set. It also contains every destination node, with path cost infinity and flags with D bit set.¶
A result path list or tree named as ResultPathTree, which contains the shortest paths from the source node to the boundary nodes and destination nodes. Initially, ResultPathTree is empty.¶
Alternatively, the result path list or tree can be combined into the candidate node list. We may set bit T to one in the node flags for the candidate node when grafting it into the existing result path list or tree. Thus all the candidate nodes with bit T set to one in the candidate list constitute the result path tree or list.¶
FSPC for computing a path for an MPLS TE P2MP LSP crossing a number of domains from a source node to a number of destination nodes can be described as follows:¶
Initially, a PCC sends a PCE responsible for the source domain a request with CandidateNodeList and ResultPathTree initialized.¶
When the PCE responsible for a domain (called current domain) receives a request for computing the path for the MPLS TE P2MP LSP, it checks whether the current PCE is the PCE responsible for the node C with the minimum cost in the CandidateNodeList. If it is, then remove C from CandidateNodeList and graft it into ResultPathTree (i.e., set flag bit T of node C to one); otherwise, a PCReq message is sent to the PCE for node C.¶
Suppose that node C is in the current domain. The ResultPathTree is built from C in the following steps.¶
If node C is a destination node (i.e., the Destination Node (D) bit in the Flags is set), then check whether the path cost to node C is infinity. If it is, then we can not find any path for the P2MP LSP, and a repply message with failure reasons is sent; otherwise, if all the destinations are on the result path tree, then the shortest path is found and a PCRep message with the path is sent to the PCE/PCC which sends the request to the current PCE.¶
If node C is an entry boundary node or the source node, then the optimal path segments from node C to every destination node and every exit boundary node of the current domain that is not on the result path tree and satisfies the given constraints are computed through using CSPF and as special links.¶
For every node N connected to node C through a special link (i.e., the optimal path segment satisfying the given constraints), it is merged into CandidateNodeList. The cost to node N is the sum of the cost to node C and the cost of the special link (i.e., the path segment) between C and N. If node N is not in the candidate node list, then node N is added into the list with the cost to node N, node C as its previous hop node and a PCE for node N. The PCE for node N is the current PCE if node N is an ASBR; otherwise (node N is an ABR, an exit boundary node of the current domain and an entry boundary node of the domain next to the current domain) the PCE for node N is the PCE for the next domain. If node N is in the candidate node list and the cost to node N through node C is less than the cost to node N in the list, then replace the cost to node N in the list with the cost to node N through node C and the previous hop to node N in the list with node C.¶
If node C is an exit boundary node and there are inter-domain links connecting to it (i.e., node C is an ASBR) and satisfying the constraints, then for every node N connecting to C, satisfying the constraints and not on the result path tree, it is merged into the candidate node list. The cost to node N is the sum of the cost to node C and the cost of the link between C and N. If node N is not in the candidate node list, then node N is added into the list with the cost to node N, node C as its previous hop node and the PCE for node N. If node N is in the candidate node list and the cost to node N through node C is less than the cost to node N in the list, then replace the cost to node N in the list with the cost to node N through node C and the previous hop to node N in the list with node C.¶
If the CurrentPCE is the same as the PCE for the node D with the minimum cost in CandidateNodeList, then the node D is removed from CandidateNodeList and grafted to ResultPathTree (i.e., set flag bit T of node D to one), and the above steps are repeated; otherwise, a request message is to be sent to the PCE for node D.¶
In this section, we describe the processing of the request and reply messages with Forward search bit set for FSPC. Each of the request and reply messages mentioned below has its Forward search bit set even though we do not indicate this explicitly.¶
In the case that a reply message is a final reply, which contains the optimal path from the source to the destination, the reply message is sent toward the PCC along the path that the request message goes from the PCC to the current PCE in reverse direction.¶
In the case that a request message is to be sent to the PCE for node D with the minimum cost in the candidate node list and there is a PCE session between the current domain and the next domain containing node D, the current PCE sends the PCE for node D through the session a request message with the source node, the destination node, CandidateNodeList and ResultPathTree.¶
In the case that a request message is to be sent to the PCE for node D and there is not any PCE session between the current PCE and the PCE for node D, a reply message is sent toward a branch point on the result path tree from the current domain along the path that the request message goes from the PCC to the current PCE in reverse direction. From the branch point, there is a downward path to the domain containing the previous hop node of node D on the result path tree and to the domain containing node D. At this branch point, the request message is sent to the PCE for node D along the downward path.¶
Suppose that node D has the minimum cost in CandidateNodeList when a PCE receives a request message or a reply message containing CandidateNodeList.¶
When a PCE (current PCE) for a domain (current domain) receives a reply message PCRep, it checks whether the reply is a final reply with the optimal path from the source to the destination. If the reply is the final reply, the current PCE sends the reply to the PCE that sends the request to the current PCE; otherwise, it checks whether there is a path from the current domain to the domain containing the previous hop node of node D on ResultPathTree and to the domain containing node D. If there is a path, the PCE sends a request PCReq to the PCE responsible for the next domain along the path; otherwise, it sends a reply PCRep to the PCE that sends the request to the current PCE.¶
When a PCE receives a request PCReq, it checks whether the current domain contains node D. If it does, then node D is removed from CandidateNodeList and grafted to ResultPathTree (i.e., set flag bit T of node D to one), and the above steps in the previous sub section are repeated; otherwise, the PCE sends a request PCReq to the PCE responsible for the next domain along the path from the current domain to the domain containing the previous hop node of node D on ResultPathTree and to the domain containing node D.¶
RFC 5441 describes the Backward Recursive Path Computation (BRPC) algorithm or procedure for computing an MPLS TE P2P LSP path from a source node to a destination node crossing multiple domains. Comparing to BRPC, there are a number of differences between BRPC and the Forward-Search P2MP TE LSP Inter-Domain Path Computation (FSPC). Some of the differences are briefed below.¶
At first, BRPC is for computing a shortest path from a source node to a destination node crossing multiple domains. FSPC is for computing a shortest path from a source node to a number of destination nodes crossing multiple domains.¶
Secondly, for BRPC to compute a shortest path from a source node to a destination node crossing multiple domains, we MUST provide a sequence of domains from the source node to the destination node to BRPC in advance. FSPC does not need any sequence of domains for computing a shortest inter-domain P2MP path.¶
Moreover, for a given sequence of domains domain(1), domain(2), ... , domain(n), BRPC searches the shortest path from domain(n), to domain(n-1), until domain(1). Thus it is hard for BRPC to be extended for computing a shortest path from a source node to a number of destination nodes crossing multiple domains. FSPC calculates a shortest path in a special topology from the source node to the destination nodes using CSPF.¶
The extensions to PCEP for FSPC include the definition of a new flag in the RP object, a result path list/tree and a candidate node list in a request message.¶
The following flag is added into the RP Object:¶
The F bit is added in the flag bits field of the RP object to tell the receiver of the message that the request/reply is for FSPC.¶
o F (FSPC bit - 1 bit):
0: This indicates that this is not PCReq/PCRep for FSPC.
1: This indicates that this is PCReq or PCRep message for FSPC.
¶
The T bit is added in the flag bits field of the RP object to tell the receiver of the message that the reply is for transferring a request message to the domain containing the node with minimum cost in the candidate list.¶
o T (Transfer request bit - 1 bit):
0: This indicates that this is not a PCRep
for transferring a request message.
1: This indicates that this is a PCRep message
for transferring a request message.
¶
Setting Transfer request T-bit in a RP Object to one indicates that a reply message containing the RP Object is for transferring a request message to the domain containing the node with minimum cost in the candidate list.¶
The IANA request is referenced in Section below (Request Parameter Bit Flags) of this document.¶
This F bit with the N bit defined in RFC6006 can indicate whether the request/reply is for FSPC of an MPLS TE P2MP LSP or an MPLS TE P2P LSP.¶
o F = 1 and N = 1: This indicates that this is a PCReq/PCRep
message for FSPC of an MPLS TE P2MP LSP.
o F = 1 and N = 0: This indicates that this is a PCReq/PCRep
message for FSPC of an MPLS TE P2P LSP.
¶
The figure below illustrates a PCE IPv4 object body (Object-Type=1), which comprises a PCE IPv4 address. The PCE IPv4 address object indicates the IPv4 address of a PCE , with which a PCE session may be established and to which a request message may be sent.¶
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PCE IPv4 address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
¶
The format of the PCE object body for IPv6 (Object-Type=2) is as follows:¶
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| PCE IPv6 address (16 bytes) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
¶
The candidate-node-list-obj object contains a list of candidate nodes. A new PCEP object class and type are requested for it. The format of the candidate-node-list-obj object body is as follows:¶
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
// <candidate-node-list> //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
¶
The following is the definition of the candidate node list.¶
<candidate-node-list>::= <candidate-node>
[<candidate-node-list>]
<candidate-node>::= <ERO>
<candidate-attribute-list>
<candidate-attribute-list>::= [<attribute-list>]
[<PCE>]
[<Node-Flags>]
¶
The ERO in a candidate node contain just the path segment of the last link of the path, which is from the previous hop node of the tail end node of the path to the tail end node. With this information, we can graft the candidate node into the existing result path list or tree.¶
Simply speaking, a candidate node has the same or similar format of a path defined in RFC 5440, but the ERO in the candidate node just contain the tail end node of the path and its previous hop, and the candidate node may contain two new objects PCE and node flags.¶
The Node Flags object is used to indicate the characteristics of the node in a candidate node list in a request or reply message for FSPC. The Node Flags object comprises a Reserved field, and a number of Flags.¶
The format of the Node Flags object body is as follows:¶
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|D|S|I|E|N| Flags | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
¶
where¶
o D = 1: The node is a destination node.
o S = 1: The node is a source node.
o I = 1: The node is an entry boundary node.
o E = 1: The node is an exit boundary node.
o T = 1: The node is on the result path tree.
¶
Below is the message format for a request message with the extension of a result path list and a candidate node list:¶
<PCReq Message>::= <Common Header>
<request>
<request>::= <RP> <END-POINT-RRO-PAIR-LIST> [<OF>] [<LSPA>]
[<BANDWIDTH>] [<metric-list>] [<RRO>[<BANDWIDTH>]]
[<IRO>] [<LOAD-BALANCING>]
[<result-path-list>]
[<candidate-node-list-obj>]
where:
<result-path-list>::=<path>[<result-path-list>]
<path>::= <ERO><attribute-list>
<attribute-list>::=[<LSPA>] [<BANDWIDTH>] [<metric-list>]
[<IRO>]
<candidate-node-list-obj> contains a <candidate-node-list>
<candidate-node-list>::= <candidate-node>
[<candidate-node-list>]
<candidate-node>::= <ERO>
<candidate-attribute-list>
<candidate-attribute-list>::= [<attribute-list>]
[<PCE>]
[<Node-Flags>]
The definition for the result path list that may be added into a request message is the same as that for the path list in a reply message that is described in RFC5440.¶
Below is the message format for a reply message with the extension of a result path list and a candidate node list:¶
<PCRep Message> ::= <Common Header>
<response>
<response> ::= <RP> [<END-POINT-PATH-PAIR-LIST>]
[<NO-PATH>] [<attribute-list>]
[<result-path-list>]
[<candidate-node-list-obj>]
where:
<candidate-node-list-obj> contains a <candidate-node-list>
¶
If the path from the source to the destinations is not found yet and there are still chances to find a path (i.e., the candidate list is not empty), the reply message contains candidate-node-list-obj consisting of the information of the candidate list, which is encoded. In this case, the Transfer request T-bit in the RP Object is set to one.¶
If the path from the source to the destination is found, the reply message contains path-list comprising the information of the path.¶
The mechanism described in this document does not raise any new security issues for the PCEP protocols.¶
This section specifies requests for IANA allocation.¶
A new RP Object Flag has been defined in this document. IANA is requested to make the following allocation from the "PCEP RP Object Flag Field" Sub-Registry:¶
Bit Description Reference
18 FSPC (F-bit) This I-D
19 Transfer Request (T-bit) This I-D
¶
The author would like to appreciate Dhruv Dhody for his great contributions and to thank Julien Meuric, Daniel King, Cyril Margaria, Ramon Casellas, Olivier Dugeon and Oscar Gonzalez de Dios for their valuable comments on this draft.¶