| Internet-Draft | A YANG Network Model for ACs | March 2023 |
| Boucadair, et al. | Expires 2 September 2023 | [Page] |
This document specifies a network model for attachment circuits. The model can be used for the provisioning of attachment circuits prior or during service provisioning (e.g., Network Slice Service). A companion service model is specified in [I-D.boro-opsawg-teas-attachment-circuit].¶
The module augments the Service Attachment Point (SAP) model with the detailed information for the provisioning of attachment circuits in Provider Edges (PEs).¶
This note is to be removed before publishing as an RFC.¶
Discussion of this document takes place on the Operations and Management Area Working Group Working Group mailing list (opsawg@ietf.org), which is archived at https://mailarchive.ietf.org/arch/browse/opsawg/.¶
Source for this draft and an issue tracker can be found at https://github.com/boucadair/network-attachment-circuits.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 2 September 2023.¶
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
The procedure to provision a service in a service provider network may depend on the practices adopted by a service provider, including the flow put in place for the provisioning of advanced network services and how they are bound to an attachment circuit. For example, the same attachment circuit may be used to host multiple services. In order to avoid service interference and redundant information in various locations, a service provider may expose an interface to manage ACs network-wide. Customers can then request a base attachment circuit to be put in place, and then refer to that base AC when requesting services that are bound to that AC. [I-D.boro-opsawg-teas-attachment-circuit] specifies a data model for managing ACs as a service.¶
This document specifies a network model for attachment circuits ("ietf-ac-ntw"). The model can be used for the provisioning of attachment circuits prior or during service provisioning (e.g., Network Slice Service).¶
The document leverages [RFC9182] and [RFC9291] by adopting an AC provisioning structure that uses data nodes that are defined in these RFCs. Some refinements were introduced to cover, not only conventional service provider networks, but also specifics of other target deployments (cloud, for example).¶
The AC network model is designed as an augmnetation to the Service Attachment Point (SAP) model [I-D.ietf-opsawg-sap]. An AC can be bound to a single or multiple SAPs. Likewise, the model is designed to accomdate deployments where a SAP can be bound to one or multiple ACs.¶
.---.
|CE6|
'-+-'
ac | .---. .---. .---.
.-+-. |CE5+--------+ +--------+CE2|
.----+ +---. '---' '-+-' '---'
| '-+-' | |ac
| | |
.-+-. .-+-. .-+-.
.-+sap+-------+sap+-. .-+sap+-------------.
| '---' '---' | | '---' |
.---. .-+-. | | |
|CE1+----+sap| PE1 | | PE2 |
'---' ac '-+-' | | |
'-------------------' '-------------------'
.-------------------. .-------------------.
| | | .-+-. ac .---.
| PE3 | | PE4 |sap+----+CE5|
| | | '---' '---'
| .---. | | .---. .---. .---. |
'-------------+sap+-' '-+sap+-+sap+-+sap+-'
'-+-' '-+-' '-+-' '-+-'
|ac | |ac |ac
.-+-. | .-+-. |
|CE3+--------ac------' |CE4+---'
'---' '---'
The AC network model uses the AC common model defined in [I-D.boro-opsawg-teas-attachment-circuit].¶
The YANG data model in this document conforms to the Network Management Datastore Architecture (NMDA) defined in [RFC8342].¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
The reader should be familiar with the terms defined in Section 2 of [I-D.ietf-opsawg-sap].¶
This document uses the term "network model" as defined in Section 2.1 of [RFC8969].¶
The meanings of the symbols in the YANG tree diagrams are defined in [RFC8340].¶
This document uses the following terms:¶
A physical or logical link that connects a customer node (or site) to a provider network. A bearer can be a wireless or wired link. One or multiple technologies can be used to build a bearer. The bearer type can be specified by a customer.¶
The operator allocates a unique bearer reference to identify a bearer within its network (e.g., customer line identifier). Such a reference can be retrieved by a customer and used in subsequent service placement requests to unambiguously identify where a service is to be bound.¶
The concept of bearer can be generalized to refer to the required underlying connection for the provisioning of an attachment circuit. One or multiple attachment circuits may be hosted over the same bearer (e.g., multiple VLANs on the same bearer that is provided by a physical link).¶
Denotes a functional entity responsible for the management of the service provider network.¶
Refers to a functional entity that interacts with the customer of a network service. The service orchestrator is typically responsible for the attachment circuits, the Provider Edge (PE) selection, and requesting the activation of the requested service to a network controller.¶
A network that is able to provide network services (e.g., Network Slice Services).¶
A service provider that offers network services (e.g., Network Slice Services).¶
Refers to a customer-owned endpoint that terminates an attachment circuit. Such an endpoint can be a Customer Edge (CE), a Network Function (NF), a peer ASBR, etc.¶
Figure 2 shows the positioning of the AC network model in the overall service delivery process.¶
+---------------+
| Customer |
+-------+-------+
Customer Service Model |
e.g., slice-svc, ac-svc |
+-------+-------+
| Service |
| Orchestration |
+-------+-------+
Network Model |
e.g., l3vpn-ntw, sap, ac-ntw |
+-------+-------+
| Network |
| Orchestration |
+-------+-------+
Network Configuration Model |
+-----------+-----------+
| |
+--------+------+ +--------+------+
| Domain | | Domain |
| Orchestration | | Orchestration |
+---+-----------+ +--------+------+
Device | | |
Configuration | | |
Model | | |
+----+----+ | |
| Config | | |
| Manager | | |
+----+----+ | |
| | |
| NETCONF/CLI..................
| NETCONF/CLI..................
| | |
+--------------------------------+
+----+ Bearer | | Bearer +----+
|CTP +--------+ Network +--------+ CTP|
+----+ | | +----+
+--------------------------------+
Site A Site B
The overall tree structure of the module is shown in Figure 3. A node can host one or more SAPs as per [I-D.ietf-opsawg-sap]. Each SAP terminate one or multiple ACs. The SAP model in [I-D.ietf-opsawg-sap] is thus augmented with required AC-related information. Also, in order to ease the correlation between the AC exposed at the service layer and the one that is actually provisioned in the network operation, a reference to the AC exposed to the customer ('ac-ref') is stored in the 'ac-ntw' module.¶
Unlike the AC service model, an AC is uniquely identified within the scope of a node not a network. An AC can be characterized using Layer 2 connectivity, Layer 3 connectivity, routing protocols, OAM, and security considerations. In order to factorize a set of data that is provisioned for a set of ACs, a set of profiled can be defined at the network level, and then called under the node level. The information contained in the profile are thus inherited, unless the corresponding data node is refined at the AC level. In such as case, the value provided at the AC level takes precedence over the global one.¶
augment /nw:networks/nw:network:
+--rw ac-profile* [name]
...
augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
+--rw ac* [name]
+--rw name string
+--rw ac-ref? ac-svc:attachment-circuit-reference
+--rw ac-profile* [profile-id]
| +--rw profile-id -> /nw:networks/network/ac-profile/name
+--rw description? string
+--rw l2-connection
| ...
+--rw ip-connection
| ...
+--rw routing-protocols
| ...
+--rw oam
| ...
+--rw security
...
The full tree of the 'ac-ntw' is provided in Appendix A.¶
The Layer 2 connection tree structure is shown in Figure 4.¶
augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
+--rw ac* [name]
+--rw name string
+--rw ac-ref? ac-svc:attachment-circuit-reference
+--rw ac-profile* [profile-id]
| +--rw profile-id -> /nw:networks/network/ac-profile/name
+--rw description? string
+--rw l2-connection
| +--rw encapsulation
| | +--rw encap-type? identityref
| | +--rw dot1q
| | | +--rw tag-type? identityref
| | | +--rw cvlan-id? uint16
| | | +--rw tag-operations
| | | +--rw (op-choice)?
| | | | +--:(pop)
| | | | | +--rw pop? empty
| | | | +--:(push)
| | | | | +--rw push? empty
| | | | +--:(translate)
| | | | +--rw translate? empty
| | | +--rw tag-1? dot1q-types:vlanid
| | | +--rw tag-1-type?
| | | | dot1q-types:dot1q-tag-type
| | | +--rw tag-2? dot1q-types:vlanid
| | | +--rw tag-2-type?
| | | dot1q-types:dot1q-tag-type
| | +--rw priority-tagged
| | | +--rw tag-type? identityref
| | +--rw qinq
| | +--rw tag-type? identityref
| | +--rw svlan-id uint16
| | +--rw cvlan-id uint16
| | +--rw tag-operations
| | +--rw (op-choice)?
| | | +--:(pop)
| | | | +--rw pop? uint8
| | | +--:(push)
| | | | +--rw push? empty
| | | +--:(translate)
| | | +--rw translate? uint8
| | +--rw tag-1? dot1q-types:vlanid
| | +--rw tag-1-type?
| | | dot1q-types:dot1q-tag-type
| | +--rw tag-2? dot1q-types:vlanid
| | +--rw tag-2-type?
| | dot1q-types:dot1q-tag-type
| +--rw (l2-service)?
| | +--:(l2-tunnel-service)
| | | +--rw l2-tunnel-service
| | | +--rw type? identityref
| | | +--rw pseudowire
| | | | +--rw vcid? uint32
| | | | +--rw far-end? union
| | | +--rw vpls
| | | | +--rw vcid? uint32
| | | | +--rw far-end* union
| | | +--rw vxlan
| | | +--rw vni-id uint32
| | | +--rw peer-mode? identityref
| | | +--rw peer-ip-address* inet:ip-address
| | +--:(l2vpn)
| | +--rw l2vpn-id? vpn-common:vpn-id
| +--rw l2-termination-point? string
| +--rw local-bridge-reference? string
| +--rw bearer-reference? string
| | {vpn-common:bearer-reference}?
| +--rw lag-interface {vpn-common:lag-interface}?
| +--rw lag-interface-id? string
| +--rw member-link-list
| +--rw member-link* [name]
| +--rw name string
+--rw ip-connection
| ...
+--rw routing-protocols
| ...
+--rw oam
| ...
+--rw security
...
The Layer 3 connection tree structure is shown in Figure 5.¶
augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
+--rw ac* [name]
+--rw name string
+--rw ac-ref? ac-svc:attachment-circuit-reference
+--rw ac-profile* [profile-id]
| +--rw profile-id -> /nw:networks/network/ac-profile/name
+--rw description? string
+--rw l2-connection
| ...
+--rw ip-connection
| +--rw l3-termination-point? string
| +--rw ipv4 {vpn-common:ipv4}?
| | +--rw local-address?
| | | inet:ipv4-address
| | +--rw prefix-length? uint8
| | +--rw address-allocation-type?
| | | identityref
| | +--rw (allocation-type)?
| | +--:(dynamic)
| | | +--rw (address-assign)?
| | | | +--:(number)
| | | | | +--rw number-of-dynamic-address? uint16
| | | | +--:(explicit)
| | | | +--rw customer-addresses
| | | | +--rw address-pool* [pool-id]
| | | | +--rw pool-id string
| | | | +--rw start-address
| | | | | inet:ipv6-address
| | | | +--rw end-address?
| | | | inet:ipv6-address
| | | +--rw (provider-dhcp)?
| | | | +--:(dhcp-service-type)
| | | | | +--rw dhcp-service-type?
| | | | | enumeration
| | | | +--:(service-type)
| | | | +--rw (service-type)?
| | | | +--:(relay)
| | | | +--rw server-ip-address*
| | | | inet:ipv6-address
| | | +--rw (dhcp-relay)?
| | | +--:(customer-dhcp-servers)
| | | +--rw customer-dhcp-servers
| | | +--rw server-ip-address*
| | | inet:ipv6-address
| | +--:(static-addresses)
| | +--rw primary-address?
| | | -> ../address/address-id
| | +--rw address* [address-id]
| | +--rw address-id string
| | +--rw customer-address? inet:ipv6-address
| +--rw ipv6 {vpn-common:ipv6}?
| +--rw local-address?
| | inet:ipv6-address
| +--rw prefix-length? uint8
| +--rw address-allocation-type?
| | identityref
| +--rw (allocation-type)?
| +--:(dynamic)
| | +--rw (address-assign)?
| | | +--:(number)
| | | | +--rw number-of-dynamic-address? uint16
| | | +--:(explicit)
| | | +--rw customer-addresses
| | | +--rw address-pool* [pool-id]
| | | +--rw pool-id string
| | | +--rw start-address
| | | | inet:ipv6-address
| | | +--rw end-address?
| | | inet:ipv6-address
| | +--rw (provider-dhcp)?
| | | +--:(dhcp-service-type)
| | | | +--rw dhcp-service-type?
| | | | enumeration
| | | +--:(service-type)
| | | +--rw (service-type)?
| | | +--:(relay)
| | | +--rw server-ip-address*
| | | inet:ipv6-address
| | +--rw (dhcp-relay)?
| | +--:(customer-dhcp-servers)
| | +--rw customer-dhcp-servers
| | +--rw server-ip-address*
| | inet:ipv6-address
| +--:(static-addresses)
| +--rw primary-address?
| | -> ../address/address-id
| +--rw address* [address-id]
| +--rw address-id string
| +--rw customer-address? inet:ipv6-address
+--rw routing-protocols
| ...
+--rw oam
| ...
+--rw security
...
The routing tree structure is shown in Figure 6.¶
module: ietf-ac-ntw
augment /nw:networks/nw:network:
+--rw ac-profile* [name]
+--rw name string
+--rw l2-connection
+--rw ip-connection
+--rw routing-protocols
| +--rw routing-protocol* [id]
| +--rw id string
| +--rw type? identityref
| +--rw bgp
| | +--rw description? string
| | +--rw local-as? inet:as-number
| | +--rw peer-as inet:as-number
| | +--rw address-family? identityref
| | +--rw multihop? uint8
| | +--rw as-override? boolean
| | +--rw allow-own-as? uint8
| | +--rw prepend-global-as? boolean
| | +--rw send-default-route? boolean
| | +--rw site-of-origin? rt-types:route-origin
| | +--rw ipv6-site-of-origin?
| | | rt-types:ipv6-route-origin
| | +--rw redistribute-connected* [address-family]
| | | +--rw address-family identityref
| | | +--rw enable? boolean
| | +--rw bgp-max-prefix
| | | +--rw max-prefix? uint32
| | | +--rw warning-threshold? decimal64
| | | +--rw violate-action? enumeration
| | | +--rw restart-timer? uint32
| | +--rw bgp-timers
| | +--rw keepalive? uint16
| | +--rw hold-time? uint16
| +--rw ospf
| | +--rw address-family? identityref
| | +--rw area-id yang:dotted-quad
| | +--rw metric? uint16
| | +--rw max-lsa? uint32
| +--rw isis
| | +--rw address-family? identityref
| | +--rw area-address area-address
| | +--rw level? identityref
| | +--rw metric? uint16
| | +--rw mode? enumeration
| +--rw rip
| | +--rw address-family? identityref
| | +--rw timers
| | | +--rw update-interval? uint16
| | | +--rw invalid-interval? uint16
| | | +--rw holddown-interval? uint16
| | | +--rw flush-interval? uint16
| | +--rw default-metric? uint8
| +--rw vrrp
| +--rw address-family? identityref
| +--rw ping-reply? boolean
+--rw oam
...
augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
+--rw ac* [name]
+--rw name string
+--rw ac-ref? ac-svc:attachment-circuit-reference
+--rw ac-profile* [profile-id]
| +--rw profile-id -> /nw:networks/network/ac-profile/name
+--rw description? string
+--rw l2-connection
| ...
+--rw ip-connection
| ...
+--rw routing-protocols
| +--rw routing-protocol* [id]
| +--rw id string
| +--rw type? identityref
| +--rw routing-profiles* [id]
| | +--rw id leafref
| | +--rw type? identityref
| +--rw static
| | +--rw cascaded-lan-prefixes
| | +--rw ipv4-lan-prefixes* [lan next-hop]
| | | {vpn-common:ipv4}?
| | | +--rw lan inet:ipv4-prefix
| | | +--rw lan-tag? string
| | | +--rw next-hop union
| | | +--rw metric? uint32
| | | +--rw bfd-enable? boolean {vpn-common:bfd}?
| | | +--rw preference? uint32
| | | +--rw status
| | | +--rw admin-status
| | | | +--rw status? identityref
| | | | +--rw last-change? yang:date-and-time
| | | +--ro oper-status
| | | +--ro status? identityref
| | | +--ro last-change? yang:date-and-time
| | +--rw ipv6-lan-prefixes* [lan next-hop]
| | {vpn-common:ipv6}?
| | +--rw lan inet:ipv4-prefix
| | +--rw lan-tag? string
| | +--rw next-hop union
| | +--rw metric? uint32
| | +--rw bfd-enable? boolean {vpn-common:bfd}?
| | +--rw preference? uint32
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw bgp
| | +--rw peer-groups
| | | +--rw peer-group* [name]
| | | +--rw name string
| | | +--rw local-address? union
| | | +--rw description? string
| | | +--rw local-as? inet:as-number
| | | +--rw peer-as inet:as-number
| | | +--rw address-family? identityref
| | | +--rw multihop? uint8
| | | +--rw as-override? boolean
| | | +--rw allow-own-as? uint8
| | | +--rw prepend-global-as? boolean
| | | +--rw send-default-route? boolean
| | | +--rw site-of-origin?
| | | | rt-types:route-origin
| | | +--rw ipv6-site-of-origin?
| | | | rt-types:ipv6-route-origin
| | | +--rw redistribute-connected* [address-family]
| | | | +--rw address-family identityref
| | | | +--rw enable? boolean
| | | +--rw bgp-max-prefix
| | | | +--rw max-prefix? uint32
| | | | +--rw warning-threshold? decimal64
| | | | +--rw violate-action? enumeration
| | | | +--rw restart-timer? uint32
| | | +--rw bgp-timers
| | | | +--rw keepalive? uint16
| | | | +--rw hold-time? uint16
| | | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(ao)
| | | | +--rw enable-ao? boolean
| | | | +--rw ao-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(md5)
| | | | +--rw md5-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm?
| | | identityref
| | +--rw neighbor* [remote-address]
| | +--rw remote-address inet:ip-address
| | +--rw local-address? union
| | +--rw peer-group?
| | | -> ../../peer-groups/peer-group/name
| | +--rw description? string
| | +--rw local-as? inet:as-number
| | +--rw peer-as inet:as-number
| | +--rw address-family? identityref
| | +--rw multihop? uint8
| | +--rw as-override? boolean
| | +--rw allow-own-as? uint8
| | +--rw prepend-global-as? boolean
| | +--rw send-default-route? boolean
| | +--rw site-of-origin?
| | | rt-types:route-origin
| | +--rw ipv6-site-of-origin?
| | | rt-types:ipv6-route-origin
| | +--rw redistribute-connected* [address-family]
| | | +--rw address-family identityref
| | | +--rw enable? boolean
| | +--rw bgp-max-prefix
| | | +--rw max-prefix? uint32
| | | +--rw warning-threshold? decimal64
| | | +--rw violate-action? enumeration
| | | +--rw restart-timer? uint32
| | +--rw bgp-timers
| | | +--rw keepalive? uint16
| | | +--rw hold-time? uint16
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(ao)
| | | | +--rw enable-ao? boolean
| | | | +--rw ao-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(md5)
| | | | +--rw md5-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw ospf
| | +--rw address-family? identityref
| | +--rw area-id yang:dotted-quad
| | +--rw metric? uint16
| | +--rw sham-links {vpn-common:rtg-ospf-sham-link}?
| | | +--rw sham-link* [target-site]
| | | +--rw target-site string
| | | +--rw metric? uint16
| | +--rw max-lsa? uint32
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(auth-key-chain)
| | | | +--rw key-chain?
| | | | key-chain:key-chain-ref
| | | +--:(auth-key-explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw isis
| | +--rw address-family? identityref
| | +--rw area-address area-address
| | +--rw level? identityref
| | +--rw metric? uint16
| | +--rw mode? enumeration
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(auth-key-chain)
| | | | +--rw key-chain?
| | | | key-chain:key-chain-ref
| | | +--:(auth-key-explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw rip
| | +--rw address-family? identityref
| | +--rw timers
| | | +--rw update-interval? uint16
| | | +--rw invalid-interval? uint16
| | | +--rw holddown-interval? uint16
| | | +--rw flush-interval? uint16
| | +--rw default-metric? uint8
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(auth-key-chain)
| | | | +--rw key-chain?
| | | | key-chain:key-chain-ref
| | | +--:(auth-key-explicit)
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw vrrp
| +--rw address-family? identityref
| +--rw vrrp-group? uint8
| +--rw backup-peer? inet:ip-address
| +--rw virtual-ip-address* inet:ip-address
| +--rw priority? uint8
| +--rw ping-reply? boolean
| +--rw status
| +--rw admin-status
| | +--rw status? identityref
| | +--rw last-change? yang:date-and-time
| +--ro oper-status
| +--ro status? identityref
| +--ro last-change? yang:date-and-time
+--rw oam
| ...
+--rw security
...
The OAM tree structure is shown in Figure 7.¶
augment /nw:networks/nw:network:
+--rw ac-profile* [name]
+--rw name string
+--rw l2-connection
+--rw ip-connection
+--rw routing-protocols
| ...
+--rw oam
+--rw bfd {vpn-common:bfd}?
+--rw session-type? identityref
+--rw desired-min-tx-interval? uint32
+--rw required-min-rx-interval? uint32
+--rw local-multiplier? uint8
+--rw holdtime? uint32
augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
+--rw ac* [name]
+--rw name string
+--rw ac-ref? ac-svc:attachment-circuit-reference
+--rw ac-profile* [profile-id]
| +--rw profile-id -> /nw:networks/network/ac-profile/name
+--rw description? string
+--rw l2-connection
| ...
+--rw ip-connection
| ...
+--rw routing-protocols
| ...
+--rw oam
| +--rw bfd
| +--rw profile? ac-svc:bfd-profile-reference
| +--rw session-type? identityref
| +--rw desired-min-tx-interval? uint32
| +--rw required-min-rx-interval? uint32
| +--rw local-multiplier? uint8
| +--rw holdtime? uint32
| +--rw authentication!
| | +--rw key-chain? key-chain:key-chain-ref
| | +--rw meticulous? boolean
| +--rw status
| +--rw admin-status
| | +--rw status? identityref
| | +--rw last-change? yang:date-and-time
| +--ro oper-status
| +--ro status? identityref
| +--ro last-change? yang:date-and-time
+--rw security
...
The security tree structure is shown in Figure 8.¶
augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
+--rw ac* [name]
+--rw name string
+--rw ac-ref? ac-svc:attachment-circuit-reference
+--rw ac-profile* [profile-id]
| +--rw profile-id -> /nw:networks/network/ac-profile/name
+--rw description? string
+--rw l2-connection
| ...
+--rw ip-connection
| ...
+--rw routing-protocols
| ...
+--rw oam
| ...
+--rw security
+--rw encryption {vpn-common:encryption}?
| +--rw enabled? boolean
| +--rw layer? enumeration
+--rw encryption-profile
+--rw (profile)?
+--:(provider-profile)
| +--rw profile-name? leafref
+--:(customer-profile)
+--rw customer-key-chain?
key-chain:key-chain-ref
This module uses types defined in [RFC6991], [RFC8177], [RFC8294], [RFC8343], [RFC9181], and IEEE Std 802.1Qcp.¶
<CODE BEGINS> file "ietf-ac-ntw@2022-11-30.yang"
module ietf-ac-ntw {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-ac-ntw";
prefix ac-ntw;
import ietf-vpn-common {
prefix vpn-common;
reference
"RFC 9181: A Common YANG Data Model for Layer 2 and Layer 3
VPNs";
}
import ietf-inet-types {
prefix inet;
reference
"RFC 6991: Common YANG Data Types, Section 4";
}
import ietf-key-chain {
prefix key-chain;
reference
"RFC 8177: YANG Data Model for Key Chains";
}
import ietf-routing-types {
prefix rt-types;
reference
"RFC 8294: Common YANG Data Types for the Routing Area";
}
import ietf-interfaces {
prefix if;
reference
"RFC 8343: A YANG Data Model for Interface Management";
}
import ieee802-dot1q-types {
prefix dot1q-types;
reference
"IEEE Std 802.1Qcp: Bridges and Bridged Networks--
Amendment 30: YANG Data Model";
}
import ietf-network {
prefix nw;
reference
"RFC 8345: A YANG Data Model for Network
Topologies, Section 6.1";
}
import ietf-sap-ntw {
prefix sap;
reference
"RFC SSSS: A YANG Network Model for Service Attachment
Points (SAPs)";
}
import ietf-ac-common {
prefix ac-common;
reference
"RFC xxx: XXXX";
}
import ietf-ac-svc {
prefix ac-svc;
reference
"RFC xxx: XXXX";
}
organization
"IETF OPSAWG (Operations and Management Area Working Group)";
contact
"WG Web: <https://datatracker.ietf.org/wg/opsawg/>
WG List: <mailto:opsawg@ietf.org>
Editor: Mohamed Boucadair
<mailto:mohamed.boucadair@orange.com>
Author: Richard Roberts
<mailto:rroberts@juniper.net>";
description
"This YANG module defines a generic YANG model for
the configuration of attachment circuits.
Copyright (c) 2023 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Revised BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC xxx; see the
RFC itself for full legal notices.";
revision 2022-11-30 {
description
"Initial revision.";
reference
"RFC xxxx: A YANG Network Data Model for Attachment Circuits";
}
// L2 conenction
grouping l2-connection {
description
"Defines Layer 2 protocols and parameters that
are required to enable AC connectivity.";
container encapsulation {
description
"Container for Layer 2 encapsulation.";
leaf encap-type {
type identityref {
base vpn-common:encapsulation-type;
}
default "vpn-common:priority-tagged";
description
"Tagged interface type. By default, the
type of the tagged interface is
'priority-tagged'.";
}
container dot1q {
when "derived-from-or-self(../encap-type, "
+ "'vpn-common:dot1q')" {
description
"Only applies when the type of the
tagged interface is 'dot1q'.";
}
description
"Tagged interface.";
uses ac-common:dot1q;
container tag-operations {
description
"Sets the tag manipulation policy for this
VPN network access. It defines a set of
tag manipulations that allow for the
insertion, removal, or rewriting
of 802.1Q VLAN tags. These operations are
indicated for the CE-PE direction.
By default, tag operations are symmetric.
As such, the reverse tag operation is
assumed on the PE-CE direction.";
choice op-choice {
description
"Selects the tag rewriting policy for a
VPN network access.";
leaf pop {
type empty;
description
"Pop the outer tag.";
}
leaf push {
type empty;
description
"Pushes one or two tags defined by the
tag-1 and tag-2 leaves. It is
assumed that, absent any policy, the
default value of 0 will be used for
the PCP setting.";
}
leaf translate {
type empty;
description
"Translates the outer tag to one or two
tags. PCP bits are preserved.";
}
}
leaf tag-1 {
when 'not(../pop)';
type dot1q-types:vlanid;
description
"A first tag to be used for push or
translate operations. This tag will be
used as the outermost tag as a result
of the tag operation.";
}
leaf tag-1-type {
type dot1q-types:dot1q-tag-type;
default "dot1q-types:s-vlan";
description
"Specifies a specific 802.1Q tag type
of tag-1.";
}
leaf tag-2 {
when '(../translate)';
type dot1q-types:vlanid;
description
"A second tag to be used for
translation.";
}
leaf tag-2-type {
type dot1q-types:dot1q-tag-type;
default "dot1q-types:c-vlan";
description
"Specifies a specific 802.1Q tag type
of tag-2.";
}
}
}
container priority-tagged {
when "derived-from-or-self(../encap-type, "
+ "'vpn-common:priority-tagged')" {
description
"Only applies when the type of the
tagged interface is 'priority-tagged'.";
}
description
"Priority tagged container.";
uses ac-common:priority-tagged;
}
container qinq {
when "derived-from-or-self(../encap-type, "
+ "'vpn-common:qinq')" {
description
"Only applies when the type of the tagged
interface is 'QinQ'.";
}
description
"Includes QinQ parameters.";
uses ac-common:qinq;
container tag-operations {
description
"Sets the tag manipulation policy for this
VPN network access. It defines a set of
tag manipulations that allow for the
insertion, removal, or rewriting
of 802.1Q VLAN tags. These operations are
indicated for the CE-PE direction.
By default, tag operations are symmetric.
As such, the reverse tag operation is
assumed on the PE-CE direction.";
choice op-choice {
description
"Selects the tag rewriting policy for a
VPN network access.";
leaf pop {
type uint8 {
range "1|2";
}
description
"Pops one or two tags as a function of the indicated pop
value.";
}
leaf push {
type empty;
description
"Pushes one or two tags defined by the tag-1 and tag-2 leaves.
It is assumed that, absent any policy, the default value of 0
will be used for PCP setting.";
}
leaf translate {
type uint8 {
range "1|2";
}
description
"Translates one or two outer tags. PCP bits are preserved.
The following operations are supported:
- translate 1 with tag-1 leaf is
provided: only the outermost tag is
translated to the value in tag-1.
- translate 2 with both tag-1 and
tag-2 leaves are provided: both
outer and inner tags are translated
to the values in tag-1 and tag-2,
respectively.
- translate 2 with tag-1 leaf is
provided: the outer tag is popped
while the inner tag is translated
to the value in tag-1.";
}
}
leaf tag-1 {
when 'not(../pop)';
type dot1q-types:vlanid;
description
"A first tag to be used for push or
translate operations. This tag will be
used as the outermost tag as a result
of the tag operation.";
}
leaf tag-1-type {
type dot1q-types:dot1q-tag-type;
default "dot1q-types:s-vlan";
description
"Specifies a specific 802.1Q tag type of tag-1.";
}
leaf tag-2 {
when 'not(../pop)';
type dot1q-types:vlanid;
description
"A second tag to be used for push or translate operations.";
}
leaf tag-2-type {
type dot1q-types:dot1q-tag-type;
default "dot1q-types:c-vlan";
description
"Specifies a specific 802.1Q tag type of tag-2.";
}
}
}
}
choice l2-service {
description
"The Layer 2 connectivity service can be
provided by indicating a pointer to an
L2VPN or by specifying a Layer 2 tunnel
service.";
container l2-tunnel-service {
description
"Defines a Layer 2 tunnel termination.
It is only applicable when a tunnel is
required. The supported values are
'pseudowire', 'vpls', and 'vxlan'. Other
values may be defined, if needed.";
uses ac-common:l2-tunnel-service;
}
case l2vpn {
leaf l2vpn-id {
type vpn-common:vpn-id;
description
"Indicates the L2VPN service associated
with an Integrated Routing and Bridging
(IRB) interface.";
}
}
}
}
grouping l2-connection-if-ref {
description
"Defines Layer 2 protocols and parameters that
are required to enable AC connectivity.";
uses l2-connection;
leaf l2-termination-point {
type string;
description
"Specifies a reference to a local Layer 2 termination point, such as a
Layer 2 sub-interface.";
}
leaf local-bridge-reference {
type string;
description
"Specifies a local bridge reference to accommodate, for example,
implementations that require internal bridging.
A reference may be a local bridge domain.";
}
leaf bearer-reference {
if-feature "vpn-common:bearer-reference";
type string;
description
"This is an internal reference for the
service provider to identify the bearer
associated with this VPN.";
}
container lag-interface {
if-feature "vpn-common:lag-interface";
description
"Container for configuration of Link Aggregation Group (LAG) interface
attributes.";
leaf lag-interface-id {
type string;
description
"LAG interface identifier.";
}
container member-link-list {
description
"Container for the member link list.";
list member-link {
key "name";
description
"Member link.";
leaf name {
type string;
description
"Member link name.";
}
}
}
}
}
grouping ip-connection {
description
"Defines IP connection parameters.";
leaf l3-termination-point {
type string;
description
"Specifies a reference to a local Layer 3 termination point, such as a
bridge domain interface.";
}
container ipv4 {
if-feature "vpn-common:ipv4";
description
"IPv4-specific parameters.";
leaf local-address {
type inet:ipv4-address;
description
"The IP address used at the provider's interface.";
}
uses ac-common:ipv4-allocation-type;
choice allocation-type {
description
"Choice of the IPv4 address allocation.";
case dynamic {
description
"When the addresses are allocated by DHCP or other
dynamic means local to the infrastructure.";
choice address-assign {
default "number";
description
"A choice for how IPv4 addresses are assigned.";
case number {
leaf number-of-dynamic-address {
type uint16;
default "1";
description
"Specifies the number of IP addresses to be assigned to
the customer on this access.";
}
}
case explicit {
container customer-addresses {
description
"Container for customer addresses to be allocated
using DHCP.";
list address-pool {
key "pool-id";
description
"Describes IP addresses to be dyncamically allocated.
When only 'start-address' is present, it represents a
single address.
When both 'start-address' and 'end-address' are
specified, it implies a range inclusive of both
addresses.";
leaf pool-id {
type string;
description
"A pool identifier for the address range from
'start-address' to 'end-address'.";
}
leaf start-address {
type inet:ipv6-address;
mandatory true;
description
"Indicates the first address in the pool.";
}
leaf end-address {
type inet:ipv6-address;
description
"Indicates the last address in the pool.";
}
}
}
}
}
choice provider-dhcp {
description
"Parameters related to DHCP-allocated addresses.
IP addresses are allocated by DHCP, which is provided
by the operator.";
leaf dhcp-service-type {
type enumeration {
enum server {
description
"Local DHCP server.";
}
enum relay {
description
"Local DHCP relay. DHCP requests
are relayed to a provider's server.";
}
}
description
"Indicates the type of DHCP service to
be enabled on this access.";
}
choice service-type {
description
"Choice based on the DHCP service type.";
case relay {
description
"Container for a list of the
provider's DHCP servers (i.e.,
'dhcp-service-type' is set to
'relay').";
leaf-list server-ip-address {
type inet:ipv6-address;
description
"IPv6 addresses of the provider's
DHCP server, for use by the local
DHCP relay.";
}
}
}
}
choice dhcp-relay {
description
"The DHCP relay is provided by the operator.";
container customer-dhcp-servers {
description
"Container for a list of the customer's DHCP servers.";
leaf-list server-ip-address {
type inet:ipv6-address;
description
"IPv6 addresses of the customer's DHCP server.";
}
}
}
}
case static-addresses {
description
"Lists the IPv6 addresses that are used.";
leaf primary-address {
type leafref {
path "../address/address-id";
}
description
"Primary IP address of the connection.";
}
list address {
key "address-id";
description
"Lists the IPv6 addresses that are used.";
leaf address-id {
type string;
description
"An identifier of the static IPv6 address.";
}
leaf customer-address {
type inet:ipv6-address;
description
"An IPv6 address of the customer side.";
}
}
}
}
}
container ipv6 {
if-feature "vpn-common:ipv6";
description
"IPv6-specific parameters.";
leaf local-address {
type inet:ipv6-address;
description
"IPv6 address of the provider side.";
}
uses ac-common:ipv6-allocation-type;
choice allocation-type {
description
"Choice of the IPv6 address allocation.";
case dynamic {
description
"When the addresses are allocated by DHCP or other
dynamic means local to the infrastructure.";
choice address-assign {
default "number";
description
"A choice for how IPv6 addresses are assigned.";
case number {
leaf number-of-dynamic-address {
type uint16;
default "1";
description
"Specifies the number of IP addresses to be assigned to
the customer on this access.";
}
}
case explicit {
container customer-addresses {
description
"Container for customer addresses to be allocated
using DHCP.";
list address-pool {
key "pool-id";
description
"Describes IP addresses to be dyncamically allocated.
When only 'start-address' is present, it represents a
single address.
When both 'start-address' and 'end-address' are
specified, it implies a range inclusive of both
addresses.";
leaf pool-id {
type string;
description
"A pool identifier for the address range from
'start-address' to 'end-address'.";
}
leaf start-address {
type inet:ipv6-address;
mandatory true;
description
"Indicates the first address in the pool.";
}
leaf end-address {
type inet:ipv6-address;
description
"Indicates the last address in the pool.";
}
}
}
}
}
choice provider-dhcp {
description
"Parameters related to DHCP-allocated addresses.
IP addresses are allocated by DHCP, which is provided
by the operator.";
leaf dhcp-service-type {
type enumeration {
enum server {
description
"Local DHCP server.";
}
enum relay {
description
"Local DHCP relay. DHCP requests
are relayed to a provider's server.";
}
}
description
"Indicates the type of DHCP service to
be enabled on this access.";
}
choice service-type {
description
"Choice based on the DHCP service type.";
case relay {
description
"Container for a list of the
provider's DHCP servers (i.e.,
'dhcp-service-type' is set to
'relay').";
leaf-list server-ip-address {
type inet:ipv6-address;
description
"IPv6 addresses of the provider's
DHCP server, for use by the local
DHCP relay.";
}
}
}
}
choice dhcp-relay {
description
"The DHCP relay is provided by the operator.";
container customer-dhcp-servers {
description
"Container for a list of the customer's DHCP servers.";
leaf-list server-ip-address {
type inet:ipv6-address;
description
"IPv6 addresses of the customer's DHCP server.";
}
}
}
}
case static-addresses {
description
"Lists the IPv6 addresses that are used.";
leaf primary-address {
type leafref {
path "../address/address-id";
}
description
"Primary IP address of the connection.";
}
list address {
key "address-id";
description
"Lists the IPv6 addresses that are used.";
leaf address-id {
type string;
description
"An identifier of the static IPv6 address.";
}
leaf customer-address {
type inet:ipv6-address;
description
"An IPv6 address of the customer side.";
}
}
}
}
}
}
/* Routing */
//BGP-generic
//BGP-extended
grouping bgp-base {
description
"Configuration specific to BGP.";
leaf description {
type string;
description
"Includes a description of the BGP
session.
This description is meant to be used
for diagnostic purposes. The semantic
of the description is local to an
implementation.";
}
leaf local-as {
type inet:as-number;
description
"Indicates a local AS Number (ASN), if
an ASN distinct from the ASN configured
at the VPN node level is needed.";
}
leaf peer-as {
type inet:as-number;
mandatory true;
description
"Indicates the customer's ASN when
the customer requests BGP routing.";
}
leaf address-family {
type identityref {
base vpn-common:address-family;
}
description
"This node contains the address families
to be activated. 'dual-stack' means
that both IPv4 and IPv6 will be
activated.";
}
leaf multihop {
type uint8;
description
"Describes the number of IP hops allowed
between a given BGP neighbor and
the PE.";
}
leaf as-override {
type boolean;
default "false";
description
"Defines whether ASN override is
enabled, i.e., replacing the ASN of
the customer specified in the AS_PATH
attribute with the local ASN.";
}
leaf allow-own-as {
type uint8;
default "0";
description
"If set, specifies the maximum number of
occurrences of the provider's ASN that
are permitted within the AS_PATH
before it is rejected.";
}
leaf prepend-global-as {
type boolean;
default "false";
description
"In some situations, the ASN that is
provided at the VPN node level may be
distinct from the ASN configured at the
VPN network access level. When such
ASNs are provided, they are both
prepended to the BGP route updates
for this access. To disable that
behavior, 'prepend-global-as'
must be set to 'false'. In such a
case, the ASN that is provided at
the VPN node level is not prepended
to the BGP route updates for
this access.";
}
leaf send-default-route {
type boolean;
default "false";
description
"Defines whether default routes can be
advertised to a peer. If set, the
default routes are advertised to a
peer.";
}
leaf site-of-origin {
when "../address-family = 'vpn-common:ipv4' "
+ "or 'vpn-common:dual-stack'" {
description
"Only applies if IPv4 is activated.";
}
type rt-types:route-origin;
description
"The Site of Origin attribute is encoded
as a Route Origin Extended Community.
It is meant to uniquely identify the
set of routes learned from a site via a
particular CE-PE connection and is used
to prevent routing loops.";
reference
"RFC 4364: BGP/MPLS IP Virtual Private
Networks (VPNs), Section 7";
}
leaf ipv6-site-of-origin {
when "../address-family = 'vpn-common:ipv6' "
+ "or 'vpn-common:dual-stack'" {
description
"Only applies if IPv6 is activated.";
}
type rt-types:ipv6-route-origin;
description
"The IPv6 Site of Origin attribute is
encoded as an IPv6 Route Origin
Extended Community. It is meant to
uniquely identify the set of routes
learned from a site via VRF
information.";
reference
"RFC 5701: IPv6 Address Specific BGP
Extended Community
Attribute";
}
list redistribute-connected {
key "address-family";
description
"Indicates, per address family, the
policy to follow for connected
routes.";
leaf address-family {
type identityref {
base vpn-common:address-family;
}
description
"Indicates the address family.";
}
leaf enable {
type boolean;
description
"Enables the redistribution of
connected routes.";
}
}
container bgp-max-prefix {
description
"Controls the behavior when a prefix
maximum is reached.";
leaf max-prefix {
type uint32;
default "5000";
description
"Indicates the maximum number of BGP
prefixes allowed in the BGP session.
It allows control of how many
prefixes can be received from a
neighbor.
If the limit is exceeded, the action
indicated in 'violate-action' will be
followed.";
reference
"RFC 4271: A Border Gateway Protocol 4
(BGP-4), Section 8.2.2";
}
leaf warning-threshold {
type decimal64 {
fraction-digits 5;
range "0..100";
}
units "percent";
default "75";
description
"When this value is reached, a warning
notification will be triggered.";
}
leaf violate-action {
type enumeration {
enum warning {
description
"Only a warning message is sent to
the peer when the limit is
exceeded.";
}
enum discard-extra-paths {
description
"Discards extra paths when the
limit is exceeded.";
}
enum restart {
description
"The BGP session restarts after
the indicated time interval.";
}
}
description
"If the BGP neighbor 'max-prefix'
limit is reached, the action
indicated in 'violate-action'
will be followed.";
}
leaf restart-timer {
type uint32;
units "seconds";
description
"Time interval after which the BGP
session will be reestablished.";
}
}
container bgp-timers {
description
"Includes two BGP timers that can be
customized when building a VPN service
with BGP used as the CE-PE routing
protocol.";
leaf keepalive {
type uint16 {
range "0..21845";
}
units "seconds";
default "30";
description
"This timer indicates the KEEPALIVE
messages' frequency between a PE
and a BGP peer.
If set to '0', it indicates that
KEEPALIVE messages are disabled.
It is suggested that the maximum
time between KEEPALIVE messages be
one-third of the Hold Time
interval.";
reference
"RFC 4271: A Border Gateway Protocol 4
(BGP-4), Section 4.4";
}
leaf hold-time {
type uint16 {
range "0 | 3..65535";
}
units "seconds";
default "90";
description
"Indicates the maximum number of
seconds that may elapse between the
receipt of successive KEEPALIVE
and/or UPDATE messages from the peer.
The Hold Time must be either zero or
at least three seconds.";
reference
"RFC 4271: A Border Gateway Protocol 4
(BGP-4), Section 4.2";
}
}
}
grouping bgp-base-with-auth {
description
"Configuration specific to BGP.";
uses bgp-base;
uses ac-common:bgp-authentication;
}
//routing profile
grouping routing-profile {
description
"Defines routing protocols.";
list routing-protocol {
key "id";
description
"List of routing protocols used on the
CE-PE link. This list can be augmented.";
leaf id {
type string;
description
"Unique identifier for the routing
protocol.";
}
leaf type {
type identityref {
base vpn-common:routing-protocol-type;
}
description
"Type of routing protocol.";
}
container bgp {
when "derived-from-or-self(../type, "
+ "'vpn-common:bgp-routing')" {
description
"Only applies when the protocol is
BGP.";
}
description
"Configuration specific to BGP.";
uses bgp-base;
}
container ospf {
when "derived-from-or-self(../type, "
+ "'vpn-common:ospf-routing')" {
description
"Only applies when the protocol is
OSPF.";
}
description
"Configuration specific to OSPF.";
uses ac-common:ospf-basic;
leaf max-lsa {
type uint32 {
range "1..4294967294";
}
description
"Maximum number of allowed Link State
Advertisements (LSAs) that the OSPF
instance will accept.";
}
}
container isis {
when "derived-from-or-self(../type, "
+ "'vpn-common:isis-routing')" {
description
"Only applies when the protocol is
IS-IS.";
}
description
"Configuration specific to IS-IS.";
uses ac-common:isis-basic;
leaf level {
type identityref {
base vpn-common:isis-level;
}
description
"Can be 'level-1', 'level-2', or
'level-1-2'.";
reference
"RFC 9181: A Common YANG Data Model for
Layer 2 and Layer 3 VPNs";
}
leaf metric {
type uint16;
default "1";
description
"Metric of the PE-CE link. It is used
in the routing state calculation and
path selection.";
}
leaf mode {
type enumeration {
enum active {
description
"The interface sends or receives
IS-IS protocol control packets.";
}
enum passive {
description
"Suppresses the sending of IS-IS
updates through the specified
interface.";
}
}
default "active";
description
"IS-IS interface mode type.";
}
}
container rip {
when "derived-from-or-self(../type, "
+ "'vpn-common:rip-routing')" {
description
"Only applies when the protocol is RIP.
For IPv4, the model assumes that RIP
version 2 is used.";
}
description
"Configuration specific to RIP routing.";
leaf address-family {
type identityref {
base vpn-common:address-family;
}
description
"Indicates whether IPv4, IPv6, or both
address families are to be activated.";
}
container timers {
description
"Indicates the RIP timers.";
reference
"RFC 2453: RIP Version 2";
leaf update-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "30";
description
"Indicates the RIP update time, i.e.,
the amount of time for which RIP
updates are sent.";
}
leaf invalid-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "180";
description
"The interval before a route is
declared invalid after no updates are
received. This value is at least
three times the value for the
'update-interval' argument.";
}
leaf holddown-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "180";
description
"Specifies the interval before better
routes are released.";
}
leaf flush-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "240";
description
"Indicates the RIP flush timer, i.e.,
the amount of time that must elapse
before a route is removed from the
routing table.";
}
}
leaf default-metric {
type uint8 {
range "0..16";
}
default "1";
description
"Sets the default metric.";
}
}
container vrrp {
when "derived-from-or-self(../type, "
+ "'vpn-common:vrrp-routing')" {
description
"Only applies when the protocol is the
Virtual Router Redundancy Protocol
(VRRP).";
}
description
"Configuration specific to VRRP.";
reference
"RFC 5798: Virtual Router Redundancy
Protocol (VRRP) Version 3 for
IPv4 and IPv6";
leaf address-family {
type identityref {
base vpn-common:address-family;
}
description
"Indicates whether IPv4, IPv6, or both
address families are to be enabled.";
}
leaf ping-reply {
type boolean;
default "false";
description
"Controls whether the VRRP speaker
should reply to ping requests.";
}
}
}
}
grouping routing {
description
"Defines routing protocols.";
list routing-protocol {
key "id";
description
"List of routing protocols used on the
CE-PE link. This list can be augmented.";
leaf id {
type string;
description
"Unique identifier for the routing
protocol.";
}
leaf type {
type identityref {
base vpn-common:routing-protocol-type;
}
description
"Type of routing protocol.";
}
list routing-profiles {
key "id";
description
"Routing profiles.";
leaf id {
type leafref {
path "/nw:networks/nw:network"
+ "/ac-ntw:specific-provisioning-profiles/valid-provider-identifiers"
+ "/routing-profile-identifier/id";
}
//type ac-svc:routing-profile-reference;
description
"Routing profile to be used.";
}
leaf type {
type identityref {
base vpn-common:ie-type;
}
description
"Import, export, or both.";
}
}
container static {
when "derived-from-or-self(../type, "
+ "'vpn-common:static-routing')" {
description
"Only applies when the protocol is a
static routing protocol.";
}
description
"Configuration specific to static
routing.";
container cascaded-lan-prefixes {
description
"LAN prefixes from the customer.";
list ipv4-lan-prefixes {
if-feature "vpn-common:ipv4";
key "lan next-hop";
description
"List of LAN prefixes for the site.";
uses ac-common:ipv4-static-rtg-entry;
leaf bfd-enable {
if-feature "vpn-common:bfd";
type boolean;
description
"Enables Bidirectional Forwarding
Detection (BFD).";
}
leaf preference {
type uint32;
description
"Indicates the preference associated
with the static route.";
}
uses vpn-common:service-status;
}
list ipv6-lan-prefixes {
if-feature "vpn-common:ipv6";
key "lan next-hop";
description
"List of LAN prefixes for the site.";
uses ac-common:ipv4-static-rtg-entry;
leaf bfd-enable {
if-feature "vpn-common:bfd";
type boolean;
description
"Enables BFD.";
}
leaf preference {
type uint32;
description
"Indicates the preference associated
with the static route.";
}
uses vpn-common:service-status;
}
}
}
container bgp {
when "derived-from-or-self(../type, "
+ "'vpn-common:bgp-routing')" {
description
"Only applies when the protocol is
BGP.";
}
description
"Configuration specific to BGP.";
container peer-groups {
description
"Configuration for BGP peer-groups";
list peer-group {
key "name";
description
"List of BGP peer-groups configured on the local system -
uniquely identified by peer-group name";
leaf name {
type string;
description
"Name of the BGP peer-group";
}
leaf local-address {
type union {
type inet:ip-address;
type if:interface-ref;
}
description
"Sets the local IP address to use for
the BGP transport session. This may be
expressed as either an IP address or a
reference to an interface.";
}
uses bgp-base-with-auth;
}
}
list neighbor {
key "remote-address";
description
"List of BGP neighbors.";
leaf remote-address {
type inet:ip-address;
description
"The remote IP address of this entry's BGP peer.";
}
leaf local-address {
type union {
type inet:ip-address;
type if:interface-ref;
}
description
"Sets the local IP address to use for
the BGP transport session. This may be
expressed as either an IP address or a
reference to an interface.";
}
leaf peer-group {
type leafref {
path "../../peer-groups/peer-group/name";
}
description
"The peer-group with which this neighbor is
associated.";
}
uses bgp-base-with-auth;
uses vpn-common:service-status;
}
}
container ospf {
when "derived-from-or-self(../type, "
+ "'vpn-common:ospf-routing')" {
description
"Only applies when the protocol is
OSPF.";
}
description
"Configuration specific to OSPF.";
uses ac-common:ospf-basic;
container sham-links {
if-feature "vpn-common:rtg-ospf-sham-link";
description
"List of sham links.";
reference
"RFC 4577: OSPF as the Provider/Customer
Edge Protocol for BGP/MPLS IP
Virtual Private Networks
(VPNs), Section 4.2.7
RFC 6565: OSPFv3 as a Provider Edge to
Customer Edge (PE-CE) Routing
Protocol, Section 5";
list sham-link {
key "target-site";
description
"Creates a sham link with another
site.";
leaf target-site {
type string;
description
"Target site for the sham link
connection. The site is referred
to by its identifier.";
}
leaf metric {
type uint16;
default "1";
description
"Metric of the sham link. It is
used in the routing state
calculation and path selection.
The default value is set to '1'.";
reference
"RFC 4577: OSPF as the
Provider/Customer Edge
Protocol for BGP/MPLS IP
Virtual Private Networks
(VPNs), Section 4.2.7.3
RFC 6565: OSPFv3 as a Provider Edge
to Customer Edge (PE-CE)
Routing Protocol,
Section 5.2";
}
}
}
leaf max-lsa {
type uint32 {
range "1..4294967294";
}
description
"Maximum number of allowed Link State
Advertisements (LSAs) that the OSPF
instance will accept.";
}
uses ac-common:ospf-authentication;
uses vpn-common:service-status;
}
container isis {
when "derived-from-or-self(../type, "
+ "'vpn-common:isis-routing')" {
description
"Only applies when the protocol is
IS-IS.";
}
description
"Configuration specific to IS-IS.";
uses ac-common:isis-basic;
leaf level {
type identityref {
base vpn-common:isis-level;
}
description
"Can be 'level-1', 'level-2', or
'level-1-2'.";
reference
"RFC 9181: A Common YANG Data Model for
Layer 2 and Layer 3 VPNs";
}
leaf metric {
type uint16;
default "1";
description
"Metric of the PE-CE link. It is used
in the routing state calculation and
path selection.";
}
leaf mode {
type enumeration {
enum active {
description
"The interface sends or receives
IS-IS protocol control packets.";
}
enum passive {
description
"Suppresses the sending of IS-IS
updates through the specified
interface.";
}
}
default "active";
description
"IS-IS interface mode type.";
}
uses ac-common:isis-authentication;
uses vpn-common:service-status;
}
container rip {
when "derived-from-or-self(../type, "
+ "'vpn-common:rip-routing')" {
description
"Only applies when the protocol is RIP.
For IPv4, the model assumes that RIP
version 2 is used.";
}
description
"Configuration specific to RIP routing.";
leaf address-family {
type identityref {
base vpn-common:address-family;
}
description
"Indicates whether IPv4, IPv6, or both
address families are to be activated.";
}
container timers {
description
"Indicates the RIP timers.";
reference
"RFC 2453: RIP Version 2";
leaf update-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "30";
description
"Indicates the RIP update time, i.e.,
the amount of time for which RIP
updates are sent.";
}
leaf invalid-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "180";
description
"The interval before a route is
declared invalid after no updates are
received. This value is at least
three times the value for the
'update-interval' argument.";
}
leaf holddown-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "180";
description
"Specifies the interval before better
routes are released.";
}
leaf flush-interval {
type uint16 {
range "1..32767";
}
units "seconds";
default "240";
description
"Indicates the RIP flush timer, i.e.,
the amount of time that must elapse
before a route is removed from the
routing table.";
}
}
leaf default-metric {
type uint8 {
range "0..16";
}
default "1";
description
"Sets the default metric.";
}
uses ac-common:rip-authentication;
uses vpn-common:service-status;
}
container vrrp {
when "derived-from-or-self(../type, "
+ "'vpn-common:vrrp-routing')" {
description
"Only applies when the protocol is the
Virtual Router Redundancy Protocol
(VRRP).";
}
description
"Configuration specific to VRRP.";
reference
"RFC 5798: Virtual Router Redundancy
Protocol (VRRP) Version 3 for
IPv4 and IPv6";
leaf address-family {
type identityref {
base vpn-common:address-family;
}
description
"Indicates whether IPv4, IPv6, or both
address families are to be enabled.";
}
leaf vrrp-group {
type uint8 {
range "1..255";
}
description
"Includes the VRRP group identifier.";
}
leaf backup-peer {
type inet:ip-address;
description
"Indicates the IP address of the peer.";
}
leaf-list virtual-ip-address {
type inet:ip-address;
description
"Virtual IP addresses for a single VRRP
group.";
reference
"RFC 5798: Virtual Router Redundancy
Protocol (VRRP) Version 3 for
IPv4 and IPv6,
Sections 1.2 and 1.3";
}
leaf priority {
type uint8 {
range "1..254";
}
default "100";
description
"Sets the local priority of the VRRP
speaker.";
}
leaf ping-reply {
type boolean;
default "false";
description
"Controls whether the VRRP speaker
should reply to ping requests.";
}
uses vpn-common:service-status;
}
}
}
// OAM
grouping bfd {
description
"Grouping for BFD.";
leaf session-type {
type identityref {
base vpn-common:bfd-session-type;
}
default "vpn-common:classic-bfd";
description
"Specifies the BFD session type.";
}
leaf desired-min-tx-interval {
type uint32;
units "microseconds";
default "1000000";
description
"The minimum interval between
transmissions of BFD Control packets, as
desired by the operator.";
reference
"RFC 5880: Bidirectional Forwarding
Detection (BFD),
Section 6.8.7";
}
leaf required-min-rx-interval {
type uint32;
units "microseconds";
default "1000000";
description
"The minimum interval between received BFD
Control packets that the PE should
support.";
reference
"RFC 5880: Bidirectional Forwarding
Detection (BFD),
Section 6.8.7";
}
leaf local-multiplier {
type uint8 {
range "1..255";
}
default "3";
description
"Specifies the detection multiplier that
is transmitted to a BFD peer.
The detection interval for the receiving
BFD peer is calculated by multiplying the
value of the negotiated transmission
interval by the received detection
multiplier value.";
reference
"RFC 5880: Bidirectional Forwarding
Detection (BFD),
Section 6.8.7";
}
leaf holdtime {
type uint32;
units "milliseconds";
description
"Expected BFD holdtime.
The customer may impose some fixed
values for the holdtime period if the
provider allows the customer to use
this function.
If the provider doesn't allow the
customer to use this function,
fixed values will not be set.";
reference
"RFC 5880: Bidirectional Forwarding
Detection (BFD),
Section 6.8.18";
}
}
// AC profile
grouping ac-profile {
description
"Grouping for attachment circuit profiles.";
// Layer 2
container l2-connection {
description
"Defines Layer 2 protocols and parameters that
are required to enable AC connectivity.";
//uses l2-connection;
}
// Layer 3
container ip-connection {
description
"Defines IP connection parameters.";
}
// Routing
container routing-protocols {
description
"Defines routing protocols.";
uses routing-profile;
}
// OAM
container oam {
description
"Defines the Operations, Administration,
and Maintenance (OAM) mechanisms used.";
container bfd {
if-feature "vpn-common:bfd";
description
"Container for BFD.";
uses bfd;
}
}
}
//AC network provisioning
grouping ac {
description
"Grouping for attachment circuits.";
leaf description {
type string;
description
"Associates a description with an AC.";
}
// Layer 2
container l2-connection {
description
"Defines Layer 2 protocols and parameters that
are required to enable AC connectivity.";
uses l2-connection-if-ref;
}
// Layer 3
container ip-connection {
description
"Defines IP connection parameters.";
uses ip-connection;
}
// Routing
container routing-protocols {
description
"Defines routing protocols.";
uses routing;
}
// OAM
container oam {
description
"Defines the Operations, Administration,
and Maintenance (OAM) mechanisms used.";
container bfd {
description
"Container for BFD.";
leaf profile {
type leafref {
path "/nw:networks/nw:network"
+ "/ac-ntw:specific-provisioning-profiles"
+ "/valid-provider-identifiers"
+ "/bfd-profile-identifier/id";
}
//type ac-svc:bfd-profile-reference;
description
"Well-known service provider profile name.
The provider can propose some profiles
to the customer, depending on the
service level the customer wants to
achieve.";
}
uses bfd;
container authentication {
presence "Enables BFD authentication";
description
"Parameters for BFD authentication.";
leaf key-chain {
type key-chain:key-chain-ref;
description
"Name of the key chain.";
}
leaf meticulous {
type boolean;
description
"Enables meticulous mode.";
reference
"RFC 5880: Bidirectional Forwarding
Detection (BFD),
Section 6.7";
}
}
uses vpn-common:service-status;
}
}
// Security
container security {
description
"Site-specific security parameters.";
container encryption {
if-feature "vpn-common:encryption";
description
"Container for AC security encryption.";
leaf enabled {
type boolean;
default "false";
description
"If set to 'true', traffic encryption on
the connection is required. Otherwise,
it is disabled.";
}
leaf layer {
when "../enabled = 'true'" {
description
"Included only when encryption
is enabled.";
}
type enumeration {
enum layer2 {
description
"Encryption occurs at Layer 2.";
}
enum layer3 {
description
"Encryption occurs at Layer 3.
For example, IPsec may be used when
a customer requests Layer 3
encryption.";
}
}
description
"Indicates the layer on which encryption
is applied.";
}
}
container encryption-profile {
when "../encryption/enabled = 'true'" {
description
"Indicates the layer on which encryption
is enabled.";
}
description
"Container for the encryption profile.";
choice profile {
description
"Choice for the encryption profile.";
case provider-profile {
leaf profile-name {
type leafref {
path "/nw:networks/nw:network"
+ "/ac-ntw:specific-provisioning-profiles"
+ "/valid-provider-identifiers"
+ "/encryption-profile-identifier/id";
}
//type ac-svc:encryption-profile-reference;
description
"Name of the service provider's
profile to be applied.";
}
}
case customer-profile {
leaf customer-key-chain {
type key-chain:key-chain-ref;
description
"Customer-supplied key chain.";
}
}
}
}
}
}
augment "/nw:networks/nw:network" {
description
"Add a list of profiles.";
// References to the profiles defined in the AC-SVC
container specific-provisioning-profiles {
description
"Contains a set of valid profiles to reference
in the AC activation.";
uses vpn-common:vpn-profile-cfg;
}
list ac-profile {
key "name";
description
"Maintains a list of AC profiles.";
leaf name {
type string;
description
"Name of the AC.";
}
uses ac-ntw:ac-profile;
}
}
augment "/nw:networks/nw:network/nw:node"
+ "/sap:service/sap:sap" {
when '../../../nw:network-types/sap:sap-network' {
description
"Augmentation parameters apply only for SAP
networks.";
}
description
"Augments SAPs with AC provisioning details.";
list ac {
key "name";
description
"List of ACs.";
leaf name {
type string;
description
"A local AC identifier.";
}
leaf ac-ref {
type ac-svc:attachment-circuit-reference;
description
"A reference to the AC as exposed at the service
level.";
}
list ac-profile {
key "profile-id";
description
"List of AC profiles.";
leaf profile-id {
type leafref {
path "/nw:networks/nw:network/ac-profile/name";
}
description
"A reference to an AC profile.";
}
}
uses ac-ntw:ac;
}
}
}
<CODE ENDS>¶
The YANG module specified in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].¶
The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.¶
There are a number of data nodes defined in this YANG module that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) and delete operations to these data nodes without proper protection or authentication can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/ vulnerability in the "ietf-ac-ntw" module:¶
Some of the readable data nodes in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control read access (e.g., via get, get-config, or notification) to these data nodes. These are the subtrees and data nodes and their sensitivity/vulnerability in the "ietf-ac-svc" module:¶
IANA is requested to register the following URI in the "ns" subregistry within the "IETF XML Registry" [RFC3688]:¶
URI: urn:ietf:params:xml:ns:yang:ietf-ac-ntw Registrant Contact: The IESG. XML: N/A; the requested URI is an XML namespace.¶
IANA is requested to register the following YANG module in the "YANG Module Names" subregistry [RFC6020] within the "YANG Parameters" registry.¶
Name: ietf-ac-ntw Maintained by IANA? N Namespace: urn:ietf:params:xml:ns:yang:ietf-ac-ntw Prefix: ac-ntw Reference: RFC xxxx¶
module: ietf-ac-ntw
augment /nw:networks/nw:network:
+--rw specific-provisioning-profiles
| +--rw valid-provider-identifiers
| +--rw external-connectivity-identifier* [id]
| | {external-connectivity}?
| | +--rw id string
| +--rw encryption-profile-identifier* [id]
| | +--rw id string
| +--rw qos-profile-identifier* [id]
| | +--rw id string
| +--rw bfd-profile-identifier* [id]
| | +--rw id string
| +--rw forwarding-profile-identifier* [id]
| | +--rw id string
| +--rw routing-profile-identifier* [id]
| +--rw id string
+--rw ac-profile* [name]
+--rw name string
+--rw l2-connection
+--rw ip-connection
+--rw routing-protocols
| +--rw routing-protocol* [id]
| +--rw id string
| +--rw type? identityref
| +--rw bgp
| | +--rw description? string
| | +--rw local-as? inet:as-number
| | +--rw peer-as inet:as-number
| | +--rw address-family? identityref
| | +--rw multihop? uint8
| | +--rw as-override? boolean
| | +--rw allow-own-as? uint8
| | +--rw prepend-global-as? boolean
| | +--rw send-default-route? boolean
| | +--rw site-of-origin? rt-types:route-origin
| | +--rw ipv6-site-of-origin?
| | | rt-types:ipv6-route-origin
| | +--rw redistribute-connected* [address-family]
| | | +--rw address-family identityref
| | | +--rw enable? boolean
| | +--rw bgp-max-prefix
| | | +--rw max-prefix? uint32
| | | +--rw warning-threshold? decimal64
| | | +--rw violate-action? enumeration
| | | +--rw restart-timer? uint32
| | +--rw bgp-timers
| | +--rw keepalive? uint16
| | +--rw hold-time? uint16
| +--rw ospf
| | +--rw address-family? identityref
| | +--rw area-id yang:dotted-quad
| | +--rw metric? uint16
| | +--rw max-lsa? uint32
| +--rw isis
| | +--rw address-family? identityref
| | +--rw area-address area-address
| | +--rw level? identityref
| | +--rw metric? uint16
| | +--rw mode? enumeration
| +--rw rip
| | +--rw address-family? identityref
| | +--rw timers
| | | +--rw update-interval? uint16
| | | +--rw invalid-interval? uint16
| | | +--rw holddown-interval? uint16
| | | +--rw flush-interval? uint16
| | +--rw default-metric? uint8
| +--rw vrrp
| +--rw address-family? identityref
| +--rw ping-reply? boolean
+--rw oam
+--rw bfd {vpn-common:bfd}?
+--rw session-type? identityref
+--rw desired-min-tx-interval? uint32
+--rw required-min-rx-interval? uint32
+--rw local-multiplier? uint8
+--rw holdtime? uint32
augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
+--rw ac* [name]
+--rw name string
+--rw ac-ref? ac-svc:attachment-circuit-reference
+--rw ac-profile* [profile-id]
| +--rw profile-id -> /nw:networks/network/ac-profile/name
+--rw description? string
+--rw l2-connection
| +--rw encapsulation
| | +--rw encap-type? identityref
| | +--rw dot1q
| | | +--rw tag-type? identityref
| | | +--rw cvlan-id? uint16
| | | +--rw tag-operations
| | | +--rw (op-choice)?
| | | | +--:(pop)
| | | | | +--rw pop? empty
| | | | +--:(push)
| | | | | +--rw push? empty
| | | | +--:(translate)
| | | | +--rw translate? empty
| | | +--rw tag-1? dot1q-types:vlanid
| | | +--rw tag-1-type?
| | | | dot1q-types:dot1q-tag-type
| | | +--rw tag-2? dot1q-types:vlanid
| | | +--rw tag-2-type?
| | | dot1q-types:dot1q-tag-type
| | +--rw priority-tagged
| | | +--rw tag-type? identityref
| | +--rw qinq
| | +--rw tag-type? identityref
| | +--rw svlan-id uint16
| | +--rw cvlan-id uint16
| | +--rw tag-operations
| | +--rw (op-choice)?
| | | +--:(pop)
| | | | +--rw pop? uint8
| | | +--:(push)
| | | | +--rw push? empty
| | | +--:(translate)
| | | +--rw translate? uint8
| | +--rw tag-1? dot1q-types:vlanid
| | +--rw tag-1-type?
| | | dot1q-types:dot1q-tag-type
| | +--rw tag-2? dot1q-types:vlanid
| | +--rw tag-2-type?
| | dot1q-types:dot1q-tag-type
| +--rw (l2-service)?
| | +--:(l2-tunnel-service)
| | | +--rw l2-tunnel-service
| | | +--rw type? identityref
| | | +--rw pseudowire
| | | | +--rw vcid? uint32
| | | | +--rw far-end? union
| | | +--rw vpls
| | | | +--rw vcid? uint32
| | | | +--rw far-end* union
| | | +--rw vxlan
| | | +--rw vni-id uint32
| | | +--rw peer-mode? identityref
| | | +--rw peer-ip-address* inet:ip-address
| | +--:(l2vpn)
| | +--rw l2vpn-id? vpn-common:vpn-id
| +--rw l2-termination-point? string
| +--rw local-bridge-reference? string
| +--rw bearer-reference? string
| | {vpn-common:bearer-reference}?
| +--rw lag-interface {vpn-common:lag-interface}?
| +--rw lag-interface-id? string
| +--rw member-link-list
| +--rw member-link* [name]
| +--rw name string
+--rw ip-connection
| +--rw l3-termination-point? string
| +--rw ipv4 {vpn-common:ipv4}?
| | +--rw local-address?
| | | inet:ipv4-address
| | +--rw prefix-length? uint8
| | +--rw address-allocation-type?
| | | identityref
| | +--rw (allocation-type)?
| | +--:(dynamic)
| | | +--rw (address-assign)?
| | | | +--:(number)
| | | | | +--rw number-of-dynamic-address? uint16
| | | | +--:(explicit)
| | | | +--rw customer-addresses
| | | | +--rw address-pool* [pool-id]
| | | | +--rw pool-id string
| | | | +--rw start-address
| | | | | inet:ipv6-address
| | | | +--rw end-address?
| | | | inet:ipv6-address
| | | +--rw (provider-dhcp)?
| | | | +--:(dhcp-service-type)
| | | | | +--rw dhcp-service-type?
| | | | | enumeration
| | | | +--:(service-type)
| | | | +--rw (service-type)?
| | | | +--:(relay)
| | | | +--rw server-ip-address*
| | | | inet:ipv6-address
| | | +--rw (dhcp-relay)?
| | | +--:(customer-dhcp-servers)
| | | +--rw customer-dhcp-servers
| | | +--rw server-ip-address*
| | | inet:ipv6-address
| | +--:(static-addresses)
| | +--rw primary-address?
| | | -> ../address/address-id
| | +--rw address* [address-id]
| | +--rw address-id string
| | +--rw customer-address? inet:ipv6-address
| +--rw ipv6 {vpn-common:ipv6}?
| +--rw local-address?
| | inet:ipv6-address
| +--rw prefix-length? uint8
| +--rw address-allocation-type?
| | identityref
| +--rw (allocation-type)?
| +--:(dynamic)
| | +--rw (address-assign)?
| | | +--:(number)
| | | | +--rw number-of-dynamic-address? uint16
| | | +--:(explicit)
| | | +--rw customer-addresses
| | | +--rw address-pool* [pool-id]
| | | +--rw pool-id string
| | | +--rw start-address
| | | | inet:ipv6-address
| | | +--rw end-address?
| | | inet:ipv6-address
| | +--rw (provider-dhcp)?
| | | +--:(dhcp-service-type)
| | | | +--rw dhcp-service-type?
| | | | enumeration
| | | +--:(service-type)
| | | +--rw (service-type)?
| | | +--:(relay)
| | | +--rw server-ip-address*
| | | inet:ipv6-address
| | +--rw (dhcp-relay)?
| | +--:(customer-dhcp-servers)
| | +--rw customer-dhcp-servers
| | +--rw server-ip-address*
| | inet:ipv6-address
| +--:(static-addresses)
| +--rw primary-address?
| | -> ../address/address-id
| +--rw address* [address-id]
| +--rw address-id string
| +--rw customer-address? inet:ipv6-address
+--rw routing-protocols
| +--rw routing-protocol* [id]
| +--rw id string
| +--rw type? identityref
| +--rw routing-profiles* [id]
| | +--rw id leafref
| | +--rw type? identityref
| +--rw static
| | +--rw cascaded-lan-prefixes
| | +--rw ipv4-lan-prefixes* [lan next-hop]
| | | {vpn-common:ipv4}?
| | | +--rw lan inet:ipv4-prefix
| | | +--rw lan-tag? string
| | | +--rw next-hop union
| | | +--rw metric? uint32
| | | +--rw bfd-enable? boolean {vpn-common:bfd}?
| | | +--rw preference? uint32
| | | +--rw status
| | | +--rw admin-status
| | | | +--rw status? identityref
| | | | +--rw last-change? yang:date-and-time
| | | +--ro oper-status
| | | +--ro status? identityref
| | | +--ro last-change? yang:date-and-time
| | +--rw ipv6-lan-prefixes* [lan next-hop]
| | {vpn-common:ipv6}?
| | +--rw lan inet:ipv4-prefix
| | +--rw lan-tag? string
| | +--rw next-hop union
| | +--rw metric? uint32
| | +--rw bfd-enable? boolean {vpn-common:bfd}?
| | +--rw preference? uint32
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw bgp
| | +--rw peer-groups
| | | +--rw peer-group* [name]
| | | +--rw name string
| | | +--rw local-address? union
| | | +--rw description? string
| | | +--rw local-as? inet:as-number
| | | +--rw peer-as inet:as-number
| | | +--rw address-family? identityref
| | | +--rw multihop? uint8
| | | +--rw as-override? boolean
| | | +--rw allow-own-as? uint8
| | | +--rw prepend-global-as? boolean
| | | +--rw send-default-route? boolean
| | | +--rw site-of-origin?
| | | | rt-types:route-origin
| | | +--rw ipv6-site-of-origin?
| | | | rt-types:ipv6-route-origin
| | | +--rw redistribute-connected* [address-family]
| | | | +--rw address-family identityref
| | | | +--rw enable? boolean
| | | +--rw bgp-max-prefix
| | | | +--rw max-prefix? uint32
| | | | +--rw warning-threshold? decimal64
| | | | +--rw violate-action? enumeration
| | | | +--rw restart-timer? uint32
| | | +--rw bgp-timers
| | | | +--rw keepalive? uint16
| | | | +--rw hold-time? uint16
| | | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(ao)
| | | | +--rw enable-ao? boolean
| | | | +--rw ao-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(md5)
| | | | +--rw md5-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm?
| | | identityref
| | +--rw neighbor* [remote-address]
| | +--rw remote-address inet:ip-address
| | +--rw local-address? union
| | +--rw peer-group?
| | | -> ../../peer-groups/peer-group/name
| | +--rw description? string
| | +--rw local-as? inet:as-number
| | +--rw peer-as inet:as-number
| | +--rw address-family? identityref
| | +--rw multihop? uint8
| | +--rw as-override? boolean
| | +--rw allow-own-as? uint8
| | +--rw prepend-global-as? boolean
| | +--rw send-default-route? boolean
| | +--rw site-of-origin?
| | | rt-types:route-origin
| | +--rw ipv6-site-of-origin?
| | | rt-types:ipv6-route-origin
| | +--rw redistribute-connected* [address-family]
| | | +--rw address-family identityref
| | | +--rw enable? boolean
| | +--rw bgp-max-prefix
| | | +--rw max-prefix? uint32
| | | +--rw warning-threshold? decimal64
| | | +--rw violate-action? enumeration
| | | +--rw restart-timer? uint32
| | +--rw bgp-timers
| | | +--rw keepalive? uint16
| | | +--rw hold-time? uint16
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(ao)
| | | | +--rw enable-ao? boolean
| | | | +--rw ao-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(md5)
| | | | +--rw md5-keychain?
| | | | key-chain:key-chain-ref
| | | +--:(explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw ospf
| | +--rw address-family? identityref
| | +--rw area-id yang:dotted-quad
| | +--rw metric? uint16
| | +--rw sham-links {vpn-common:rtg-ospf-sham-link}?
| | | +--rw sham-link* [target-site]
| | | +--rw target-site string
| | | +--rw metric? uint16
| | +--rw max-lsa? uint32
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(auth-key-chain)
| | | | +--rw key-chain?
| | | | key-chain:key-chain-ref
| | | +--:(auth-key-explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw isis
| | +--rw address-family? identityref
| | +--rw area-address area-address
| | +--rw level? identityref
| | +--rw metric? uint16
| | +--rw mode? enumeration
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(auth-key-chain)
| | | | +--rw key-chain?
| | | | key-chain:key-chain-ref
| | | +--:(auth-key-explicit)
| | | +--rw key-id? uint32
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw rip
| | +--rw address-family? identityref
| | +--rw timers
| | | +--rw update-interval? uint16
| | | +--rw invalid-interval? uint16
| | | +--rw holddown-interval? uint16
| | | +--rw flush-interval? uint16
| | +--rw default-metric? uint8
| | +--rw authentication
| | | +--rw enable? boolean
| | | +--rw keying-material
| | | +--rw (option)?
| | | +--:(auth-key-chain)
| | | | +--rw key-chain?
| | | | key-chain:key-chain-ref
| | | +--:(auth-key-explicit)
| | | +--rw key? string
| | | +--rw crypto-algorithm? identityref
| | +--rw status
| | +--rw admin-status
| | | +--rw status? identityref
| | | +--rw last-change? yang:date-and-time
| | +--ro oper-status
| | +--ro status? identityref
| | +--ro last-change? yang:date-and-time
| +--rw vrrp
| +--rw address-family? identityref
| +--rw vrrp-group? uint8
| +--rw backup-peer? inet:ip-address
| +--rw virtual-ip-address* inet:ip-address
| +--rw priority? uint8
| +--rw ping-reply? boolean
| +--rw status
| +--rw admin-status
| | +--rw status? identityref
| | +--rw last-change? yang:date-and-time
| +--ro oper-status
| +--ro status? identityref
| +--ro last-change? yang:date-and-time
+--rw oam
| +--rw bfd
| +--rw profile? leafref
| +--rw session-type? identityref
| +--rw desired-min-tx-interval? uint32
| +--rw required-min-rx-interval? uint32
| +--rw local-multiplier? uint8
| +--rw holdtime? uint32
| +--rw authentication!
| | +--rw key-chain? key-chain:key-chain-ref
| | +--rw meticulous? boolean
| +--rw status
| +--rw admin-status
| | +--rw status? identityref
| | +--rw last-change? yang:date-and-time
| +--ro oper-status
| +--ro status? identityref
| +--ro last-change? yang:date-and-time
+--rw security
+--rw encryption {vpn-common:encryption}?
| +--rw enabled? boolean
| +--rw layer? enumeration
+--rw encryption-profile
+--rw (profile)?
+--:(provider-profile)
| +--rw profile-name? leafref
+--:(customer-profile)
+--rw customer-key-chain?
key-chain:key-chain-ref
¶
TODO acknowledge.¶