Internet-Draft | IPv6 TPF Option | July 2021 |
Bonica, et al. | Expires 27 January 2022 | [Page] |
This document explains how IPv6 options can be used in IPv6 tunnels. It also defines the IPv6 Tunnel Payload Forwarding (TPF) option.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 27 January 2022.¶
Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.¶
This document explains how IPv6 options [RFC8200] can be used in IPv6 tunnels. It also defines the IPv6 Tunnel Payload Forwarding (TPF) option.¶
An IPv6 tunnel [RFC2473] connects two nodes, called the entry-point and the exit-point. The entry-point receives a packet and encapsulates it in a Tunnel IPv6 Header. Figure 1 depicts the encapsulation.¶
+----------------------------------//-----+ | Original | | | | Original Packet Payload | | Header | | +----------------------------------//-----+ < Original Packet > | v <Tunnel IPv6 Headers> < Original Packet > +---------+ - - - - - +-------------------------//--------------+ | IPv6 | IPv6 | | | | Extension | Original Packet | | Header | Headers | | +---------+ - - - - - +-------------------------//--------------+ < Tunnel IPv6 Packet >
The original packet can be any layer-2 or layer-3 packet (e.g., Ethernet, IPv4, IPv6). The Tunnel Header is an IPv6 header followed by zero or more extension headers. The resulting packet is a Tunnel IPv6 Packet.¶
The entry-point sends the Tunnel IPv6 Packet to the exit-point which then executes the following procedure:¶
The exit-point node processes the Tunnel IPv6 Header in strict left-to-right order. It processes the IPv6 header first and then processes extension headers in the order that they appear in the packet. The IPv6 header, and each extension header, includes a Next Header field. The last Next Header field processed identifies the next-protocol engine.¶
Entry-point nodes can send optional information to the next-protocol engine on the exit-point node. For example, the entry-point can indicate:¶
To send this information, the entry-point node includes an IPv6 Destination Option header in the Tunnel IPv6 Header. The IPv6 Destination Options header includes an IPv6 TPF option and the IPv6 TPF option includes TPF information. The next-protocol engine on the exit-point node uses TPF information when it forwards the original packet.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
The TPF Option contains the following fields:¶
The TPF option MAY appear in a Destination Options header that precedes an upper-layer header. It MUST NOT appear in a Hop-by-hop Options header or in a Destination Options header that precedes a Routing header.¶
NOTE : The highest-order two bits of the Option Type (i.e., the "act" bits) are 01. These bits specify the action taken by a destination node that does not recognize the option. The required action is to discard the packet. The third highest-order bit of the Option Type (i.e., the "chg" bit) is 0. This indicates that Option Data cannot be modified along the path between the packet's source and its destination.¶
An exit-point node supports one or more next-protocol engines (e.g., Ethernet, IPv4, IPv6). Each next-protocol engine supports a default forwarding procedure and zero or more special forwarding procedures.¶
When an exit-point node submits a packet to a next-protocol engine without TPF information, the next-protocol engine executes its default forwarding procedure. For example, assume that the exit-point node receives the following Tunnel IPv6 Packet:¶
In this case, the exit-point node processes and removes the Tunnel IPv6 Header. It then submits the original packet, without any TPF information, to the IPv4 protocol engine.¶
The IPv4 protocol engine executes its default forwarding procedure. It searches its Forwarding Information Base (FIB) for and entry that matches the original packet's destination address. If the search returns a FIB entry, the protocol engine forwards the packet through an interface that the FIB entry identifies.¶
When an exit-point node submits a packet to a next-protocol engine with TPF information, the next-protocol engine executes a special forwarding procedure. For example, assume that the exit-point node receives the following Tunnel IPv6 packet:¶
In this case, the exit-point node processes and removes the Tunnel IPv6 Header. It then submits the original packet, along with TPF information, to the IPv4 protocol engine.¶
The IPv4 protocol engine executes a special forwarding procedure. It forwards the packet through the interface identified by TPF information, without searching the FIB.¶
TPF information is opaque. While it must be understood by the entry-point node and the exit-point node, it does not need to be understood by any other node.¶
The IPv6 TPF option is useful in deployments where IPv6 tunnels carry:¶
When an IPv6 tunnel carries L3VPN traffic, VPN context information can be encoded in an IPv6 TPF option. Therefore, the MPLS service label that is normally present in an L3VPN packet can be eliminated.¶
When an IPv6 tunnel carries EVPN traffic, VPN context information can be encoded in an IPv6 TPF option. Therefore, the UDP and VXLAN headers that might otherwise be present can be eliminated.¶
TPF information MUST NOT be accepted from untrusted sources. The following are acceptable methods of risk mitigation:¶
All nodes at the edge of a secure TPF domain discard packets that satisfy the following criteria:¶
IANA is requested to allocate a code point from the Destination Options and Hop-by-hop Options registry (https://www.iana.org/assignments/ipv6-parameters/ipv6-parameters.xhtml#ipv6-parameters-2). This option is called "Tunnel Payload Forwarding Option". The "act" bits are 01 and the "chg" bit is 0. The suggested value is 0x41.¶
Thanks to Dr. Vanessa Ameen, Brian Carpenter, Adrian Farrel, Ishaan Gandhi, Tom Herbert, John Leddy, Srihari Sangli and Tony Li for their comments.¶